Search Documents

By D J. Bradshaw, E M. Wightman, C L. Evans, B Triffett

During the commissioning phase of Prominent Hill, periods of reduced recovery were experienced with higher-grade ore blends. This was unexpected and as part of the process to identify the cause, surveys were conducted in May 2009, with two different ore blends (copper grades: 1.94 per cent Cu (blend 1) and 2.49 per cent Cu (blend 2)). Metallurgical performance was assessed in terms of rougher recovery and grade with consideration of both pulp and froth effects. In addition, hydrodynamic measurements (gas hold up, bubble size, superficial gas velocity) as well as measurements of bubble load and top-of-froth grade were taken during the surveys and full mineralogical assessment of selected streams completed to characterise the nature of the differences. The metallurgical results showed that the lower performance was obtained with blend 2 which contained the higher amount of chalcocite and was higher-grade. Analysis of the survey data showed that for both ore blends more than half of the copper loss occurred in the +38 ¦m size fractions. Almost 30 per cent of the copper in the +38 ¦m fractions that reported to the rougher tails during processing of blend 2 was liberated compared to less than five per cent for blend 1. Additionally almost 60 per cent of the copper in the +38 ¦m fraction of blend 2 was chalcocite compared with approximately 20 per cent in blend 1. This paper discusses the sensitivity of the chalcocite-to-surface chemistry effects causing marked reductions in recovery either through reduced pulp recovery or froth phase (detachment) effects. The reagent suite and operating conditions were subsequently changed and the recoveries increased substantially and the sensitivity to ore changes eliminated. It should be noted that subsequent optimisation work, which focused on recovery improvement, has led to copper recoveries of over 90 per cent being achieved.CITATION:Bradshaw, D J, Wightman, E M, Evans, C L and Triffett, B, 2012. Characterising the reasons for the difference in performance of two ore blends in early processing at OZ Minerals Prominent Hill Operation, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 273-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By D Connelly

Magnetite orebodies generally means mining lower grade iron ores, crushing and grinding with significant energy costs in processing and the capital costs being significantly higher than for direct shipping ores (DSO). Overseas, the mining and processing of magnetite ores has a long history of production due to the lack of DSO deposits. This raises the question as to why the new magnetite projects have been so problematic and also whether there is a future for the long list of potential magnetite projects in Australia.The quality of the magnetite concentrate product is superior to most DSO products and the magnetite contains energy benefits when converted to hematite in sintering or pelletising. The industry’s hopes for new projects have been dashed and questions are being raised as to the financial viability of such projects.A comparison of Grange Resources Savage River, Arrium’s Project Magnet, the Sino Iron Project and Gindalbie’s Karara Iron Project is used to understand the differences between the projects and why some are more successful than others.CITATION:Connelly, D, 2015. What is the future for magnetite projects in Australia and why have some of the new projects been so problematic?, in Proceedings Iron Ore 2015, pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By P J. Chapman

Recent catastrophic failures of tailings storage facilities (TSFs) continue to highlight the need for a detailed understanding of failure modes and the defences that are in place within the design to mitigate the failure modes. However, in many cases the instrumentation devices and monitoring approaches selected during operation do not link back to the design defences and inappropriate or redundant instrumentation is often installed. Candidate instruments and monitoring approaches (critical controls) are presented and matched to critical failure modes, with clear linkages to the intent of each instrument/monitoring approach. Commentary on where complementary measurements with independent technology types are recommended to provide greater assurance of trends to the design engineer or TSF owner is also presented. In response to the recent TSF failures, an increasing focus is being placed on instrumentation and monitoring relating to slope instability and safeguarding against the potential for static liquefaction, using a critical state soil mechanics framework. To support selection of appropriate zoning within a stability model, three complementary devices are recommended – vibrating wire piezometers to provide an indication of pore pressure and allow the phreatic surface to be inferred, tensiometers to confirm the presence of unsaturated conditions (and hence low potential for undrained failure) and moisture content sensors to provide an indication of void ratio, and hence state parameter, in saturated zones. The combination of VWPs and tensiometers will provide complementary measurements in the saturated and unsaturated zones, and also provide information on the extent of any near-saturated zones, provided that sufficient instruments are installed.

Jul 1, 2021

By M Medina, J Alexander, R J. Longey

Capricorn Copper Pty Ltd (CCPL) are operating the Capricorn Copper Mine located at Gunpowder, Queensland. As current holder of the environmental authority for the site, CCPL have obligations to rehabilitate areas of the mine that are no longer operational and have the potential to cause/contribute to environmental harm. CCPL sought a voluntary Transitional Environmental Program (TEP) to provide an agreed program of works to cap and rehabilitate the former Mammoth Tailings Storage Facility. The voluntary TEP contained conditions that were required to be met, to reduce the potential for environmental harm from the facility. The former Mammoth Tailings Storage Facility commenced use in the early 1970’s, and is an unlined valley in-fill structure, contemporary in design compared with other such approved structures of the era. The decommissioned Mammoth Tailings Storage Facility, now known as the Old Tailings Storage Facility (Old TSF), has been a legacy source of contamination due to the existing capping not meeting modern cover criterion, and allowing oxidisation and infiltration to the underlying acid forming tailings resulting in Acid and Metalliferous Drainage (AMD) from the facility. A cover design for the Old TSF, and other mine waste storages onsite that required clay capping, had been proposed by previous operators. Under the TEP cover design phase, it was identified that a key constraint was the lack of significant quantities of low permeability clay onsite. The lack of available clay prompted the consideration of alternate lining materials for the Old TSF, with a Bituminous Geomembrane Liner (BGM) being adopted as the preferred alternative. The BGM compared favourably with clay-based materials on seepage analysis, and led to other benefits by eliminating the need for borrowing clay off site, reducing the site’s environmental footprint, and reducing construction time. The BGM cover system on the Old TSF is being monitored with the intent to use this as a case study to confirm expected performance, enabling the cover design to potentially be adopted on the remainder of the site’s mine waste storages that require capping.

Jul 1, 2021

By C L Humphrey

Biological monitoring programs for environmental protection require techniques that will provide both early detection of possible adverse effects, and assessment of the ecological significance of these effects. Monitoring techniques must include responses sensitive to the impact, that can be subjected to rigorous statistical analysis and for which statistical power is high. Such issues in baseline research of 'what and how to measure?' and 'for how long?' have been the focus of a program being developed to monitor and assess effects of mining operations on the effectively pristine, freshwater ecosystems of the Alligator Rivers Region (ARR) in tropical northern Australia. Application of the BACIP design, utilising a form of temporal replication, to univariate data (single species) and multivariate (community) data is described. For new ventures in Australia (such as mining), monitoring programs should be designed to establish with high probability that an impact on the ecosystem no greater than a prescribed amount has gone undetected - as opposed to simply allowing development to continue as long as 'proof' of impact is not available. Such a precautionary approach represents a shifting of the 'burden of proof' and would require with the BACIP design, a minimum number of baseline years in order to achieve some desired level of statistical power in a test for impact. Power analyses conducted on two to five years (depending upon the technique) of baseline data from streams of the ARR indicate that the BACIP design would not impose developmental constraints on mining and that a policy of reversal of the burden of proof would provide the cornerstone required for managing such development in an ecologically sustainable manner.

Jan 1, 1994

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By S-C Shim, H-R Lee, Y Kang, H Shin

Since iron oxide and silicon oxide are major gangue components in various types of ore, FeO-SiO2 base slag, ie fayalite slag, has been often encountered in pyrometallurgical processes of non-ferrous metals. During most matte production processes such as the smelting of Cu, Pb, and Ni, the FeOSiO2 based slag is inevitably formed and plays an important role in refining crude metal as well as engineering aspects. Recently, similar pyrometallurgical approaches have been attempted in the recovery of valuable metals (Ni, Co, Cr) from wasted secondary batteries. Thus, the viscosity of the FeO-SiO2 based slag has great significance in properly controlling smelting processes. However, when molten metal or matte does not coexist with the slag during the measurement, there has been a serious difficulty in maintaining Fe valance and consequently, the slag composition. In the present research, the viscosity of molten FeO-SiO2 slag was measured in 1573~1673 K using a rotational viscometer. In order to keep the state of iron oxides, the oxygen partial pressure was controlled using CO/CO2 gas mixture. The optimised ratio of CO/CO2 could be calculated using Fe/Fe2+ and Fe2+/Fe3+ equilibria at each temperature. The composition of the slag, particularly Fe valance, after the measurement was analysed with the aid of an inductively coupled plasma – optical emission spectroscopy (ICP-OES) and an automatic potentiometric titrator. The measurement showed that the FeO-SiO2 slag has considerably low viscosity values in the molten state, and it sharply increases as the temperature decreases. In spite of the careful oxygen partial pressure control, a part of Fe2+ was found to be oxidised to Fe3+, with a maximal case reaching about 20 per cent. The increase in viscosity of FeO-SiO2 at low temperatures can be attributed to the composition change due to an unavoidable Fe2+ oxidation. In addition, the relationship between the change in the viscosity and the liquidus temperature of FeO-SiO2 based slag was discussed to understand the composition dependence of viscosity.

Jun 19, 2024

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By P K. Wong, D A. F Oliveira, F M. Azad

In situations where foundation piles are located in proximity to existing or future tunnels, it is typical for the tunnel owner to require that sleeving of the piles be carried out to at least the invert of the tunnels to minimise any load transfer to the tunnel lining. In competent rock, this practice may be sometimes unnecessary, thus uneconomical. This paper presents an assessment of the effect of pile loading from one of the multi-storey buildings at Barangaroo South in Sydney on the adjacent future Sydney Metro tunnels. It was originally required by Transport for NSW (TfNSW) that the piles be sleeved below the tunnel invert level; however, the building developer wanted to reduce the pile sleeving depth to achieve a more economical solution due to the large number of load transfer piles being required for the project. To assess this feasibility, a full 3D commercial numerical code, FLAC3D, was used to carry out this complex soil-structure interaction analyses. Based on these assessments, it was demonstrated successfully to the TfNSW that the pile sleeving may be terminated at 2 m above the tunnel invert level. For this arrangement, the investigations found that the loading on the piles should have negligible adverse impact on the tunnel lining design. As a result of such an assessment, the proposed pile sleeving level was approved by TfNSW, thus offering an economical foundation solution for the project.CITATION:Azad, F M, Oliveira, D A F and Wong, P K, 2014. The impact of pile loading on adjacent metro tunnels – Barangaroo South, Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 355–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Wanninayake, E Novello, I Gillani

A residue storage facility (RSF) was designed to cater for Davidson Creek Area and Robertson Range Area operations under the FerrAus Pilbara iron ore development project in the Pilbara Region, Western Australia. Annual ore production was about 15 million tonnes over a period of up to 15 years. The RSF was designed to handle a tailings production rate of 2.2 Mt/a over the project life with ability to be expanded at a later date. The composition of tailings was predominantly -45 ¦ material with some spiral reject material. The fraction of solids was expected to be between 40 per cent and 50 per cent solids by weight.The RSF was designed as an above ground storage facility, integrating with a mine waste dump planned close to the selected RSF site. This integration helped to increase the stability of the RSF embankment and to reduce the construction cost. The main source of construction material for the remaining part of the RSF embankment was selected to be mine waste. The RSF was designed to be constructed in stages by considering the availability of mine waste according to the mining schedule. The use of mine waste for construction of RSF embankments has several benefits over use of borrowed material. These include less construction costs and less disturbances to the environment, by minimising borrowed areas and waste dump footprints.CITATION:Wanninayake, A, Novello, E and Gillani, I, 2013. Effective use of mine waste in the design of a residue storage facility, Pilbara region, Western Australia, in Proceedings Iron Ore 2013 , pp 39-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By M Berry

Consider these four questions:What is the definition of life-of-mine?When should life-of-mine planning seriously commence?When can life-of-mine planning seriously commence?What is the key input to effective life-of-mine planning?Whilst there is likely to be general consensus on the answers to the first three questions, the answer to the fourth question is open to debate. This author argues that understanding and managing risks and opportunities associated with geological uncertainty is the key input to effective life-of-mine planning, at all stages in the life cycle of a mining project.CITATION:Berry, M, ?2014. Effective life-of-mine planning by understanding and managing risks and opportunities associated with geological uncertainty, in Proceedings Life-of-Mine 2014 , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By A Baker

Hail Creek Mine is an open cut coal operation owned by Rio Tinto. It is located 120 km south west of Mackay in the Bowen Basin region of central Queensland. Opened in late 2003, the mine produces two high quality coking coal products that are used in the production of steel in various overseas markets. Hail Creek is a dragline and truck/shovel operation with a capacity to mine eight million tonnes per annum. In 2010, the production was more than seven million tonnes.Traditionally, coal seam edge loss had been minimised on site by the practice of coal edge buffering. Importing buffer material can be quite expensive as it requires a large involvement from the truck and shovel or dozer fleet. In order to minimise this expense, a program of front splitting was introduced on site. Front splitting however involves an additional blast interaction which places added pressure on mining schedules. Both these methods of coal protection demonstrated a significant benefit with coal loss being reduced by approximately seven per cent (absolute) compared to traditional cast blasting.With the application of electronic detonators at Hail Creek the new blasting practice of dynamic buffering is able to be performed on site. Dynamic buffering refers to a blasting practice where two or three separate blasts are initiated during the same blasting event (front-split, cast and at times presplit). The process involves firing a front-split and allowing it to have time to settle and buffer the coal edge prior to the cast blast initiating. This practice is only made possible with the use of electronic detonators and the effective absence of a surface burning front. Current practice at site involves the front-split being fired (occasionally at the same time as the presplit) and the main cast blast being initiated several seconds later. Dynamic buffering is now used for all cast blasts to coal at Hail Creek. Electronic detonators have allowed Hail Creek to achieve reduced coal losses by buffering the coal edge without compromising the mining schedule.

Nov 8, 2011

By M Habte

This paper presents a simplified method for the assessment of creep deformations in rock masses containing bands of low strength or soil strength rock. The main impetus for this work was the need to assess the impact of distinct bands of clay and/or low strength rock on the long term deformation behaviour of a rock pillar formed as part of a series of proposed tunnelling works. In particular, the authors were interested in being able to provide criterion which could be used by site personnel to assess the encountered rock conditions against design assumptions.Creep deformation versus time plots are presented for a range of material consistencies. These plots were produced using the hyperbolic creep equation proposed by Mesri et al (1981). This empirically based equation was chosen for its simplicity and practicality. Discussion is included regarding typical input parameter values and the sensitivity of the results to these values is explored. Finally, in the soil strength materials, the secondary consolidation equation is used to check the veracity of the results calculated using the hyperbolic creep equation.

Mar 8, 2011

By R Wei, Y Peng, D Seaman

This study addresses a widespread problem confronting the mining industry: the deleterious effect of clay minerals in flotation. This problem is seemingly exacerbated by the presence of iron contamination from grinding media. The interaction of clay minerals and grinding media in copper and gold flotation was investigated in this study. A low-clay ore and a high-clay ore were obtained from Telfer to represent different contents of clay minerals, while stainless steel and mild steel grinding rods were used to produce different grinding chemistry, in particular, iron contamination. Flotation tests on an unsized and sized basis were conducted to reveal how clay minerals and grinding media affect copper and gold flotation. Iron contamination and the oxidation of copper minerals were quantified by ethylene diamine-tetra acetic acid (EDTA) extraction. It is interesting to find that both clay minerals and iron contamination depressed the flotation primarily in fine particles smaller than 33 ¦m, and clay minerals played a dominant role. Although flotation of coarser particles greater than 33 ¦m was less affected by clay minerals and iron contamination, coarser grinding to increase P80 was not an effective way to improve copper and gold flotation for the high-clay ore. This study suggests that to improve copper and gold flotation from clay ores, clay dispersion in conjunction with the minimisation of iron contamination may be required.CITATION:Wei, R, Peng, Y and Seaman, D, 2013. The effect of grinding media on copper and gold flotation in the presence of clay minerals, in Proceedings World Gold 2013 , pp 283-288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R Morrison, P Walters, B Adair, V Jokovic

‘Grade Engineering&lt;sub&gt;&#174;&lt;/sub&gt; is an integrated approach to coarse rejection that matches a suite of separation technologies to ore specific characteristics and compares the net value of rejecting low value components in current feed streams to existing mine plans as part of a system-view’ (Walters, 2017). Two of these technologies are directly recoverable through screening stages: Natural Deportment and Induced Deportment. The potential for taking advantage of “Natural Deportment” by size following blasting and crushing has been demonstrated for a range of ore types. Simple and low cost screening can in some cases generate a fine product with improved grade and a lower grade oversize which can be directed to leach or to waste. Where an ore body consists of many different ore types, the traditional approach of blending to metal grade will often add to complexity of treatment, which will reduce the effect of “natural deportment” by size.CITATION: Jokovic, V, Walters, P, Adair, B and Morrison, R, 2018. Applying enhanced grade engineering to complex ore bodies, in Proceedings Complex Orebodies Conference 2018, pp 21–23 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By M Haydon

How do you portray a large structurally and stratigraphically complex deposit to return a meaningful resource estimation, and produce a geological model that is useable for planning on a daily basis? The George Fisher Mine is located 22 km north of Mount Isa and forms part of XstrataÆs Zinc Group operations. It is currently a major producer of zinc, lead and silver in the region with an estimated total resource for all categories of 127 Mt at 100g/t Ag, 5.3 per cent Pb and 9.2 per cent Zn (June 2005). Production in 2005 totalled 2 647 492 wet tonnes for 317 699 kg Ag, 140 317 tonnes Pb and 230 331 tonnes Zn from underground operations. George Fisher (GF) consists of two deposits that are structurally complex on a mine scale, George Fisher North (GFN) and George Fisher South (GFS). Regional faulting has resulted in a 2 km long package of variably pyritic shale and siltstone that separates the deposits. This paper looks specifically at GFN. Distinct correlations exist between the two deposits based on stratigraphic matches; however, orebody characteristics, geometry and fault architectures differ significantly between the two. The deposits consist of multiple, sedimentary-hosted, stratiform orebodies from 2 to 25 m wide, separated by waste intervals of variable width. Each ore-waste interval is modelled as an individual geological domain. Structurally, George Fisher North (GFN) contains a series of major late-stage NE faults with dextral offset(s) of up to 130 m. Further complexity is added by NS, NW and NNE striking fault orientations that can produce either a loss or repeat of stratigraphy, local drag folding, orebody attenuation and block rotation. Due to this structural complexity and orebody offsets, domains at GFN are further divided into fault blocks (FB). The GFN model comprises eight FBs over a strike length of 1 km, all of which are modelled independently. As drilling progresses and additional resources are converted, further FBs will be added at major fault offsets to accommodate orebody and model expansion. This will be in addition to what is already a large and time-consuming data set to manage and update. For example, each FB has 18 domains each with two constraining wireframes (hanging wall and footwall). Each wireframe has several sets of point data depending on the type of data available, ie diamond drilling, mapping or interpretation points. This equates to over 1100 separate files to manage. Additional wireframes and files are also required for major structures, daily planning requirements and block model runs. In total some 1500 files are managed, updated and maintained for GFN alone. The ongoing need to expand as a business and optimise production in the current economic climate where there is a global demand for metal has led to an increase in production at GF. This has resulted in a rapidly growing data set and highlights the importance of practical and efficient modelling to achieve a meaningful resource estimate. This paper focuses on the geological modelling, modelling approaches and techniques employed for the GFN deposit.

Jan 1, 2006

By Low Russell

Mark Westfield, writing in The Australian on 16 May 1994 stated: The role of the independent expert is crucial to Australia&apos;s investment system. When it falls down, there can be very dramatic consequences. The scope of these consequences was dramatically illustrated in the decision of Rogers J. at first instance in Cambridge Credit Corporation v. Hutcheson (1983) 8 ACLR 123 when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million, well in excess of their insurance cover. No comfort should be sought in the fact that this decision was overturned on appeal, for the result of the appeal rested on whether there had been a causal connection between the breach of contract which had occurred and the loss suffered, rather than on the fundamental principle of auditors&apos; liability. Thus: Those who prepare experts&apos; reports in company cases carry a heavy moral responsibility, whatever their legal duties may be... Unless high standards are observed by those who prepare these reports, there is a danger that systems established for the protection of the investing public will, in fact, operate to their detriment through reliance placed on those reports and on the reputations of those who furnish them. In lending his name, the expert will often, as in this case, be lending a name to conjure With.

Jan 1, 1995

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By B C. McLellan

The decline of ore grades on land, increasing demand and high prices for various minerals have led to an increased interest in mining the deep ocean sea floor. The potential deep ocean reserves are vast and in some circumstances the grades are high enough to consider mining. However, the consequences of such mining are as yet uncertain. This paper will present the results of a comparative assessment of life cycle impacts of deep ocean minerals. Two alternative extraction technologies from different deep ocean resource types were examined and key commodities are considered. Initial results indicate that the energy requirements will be higher than the average land-based resources, but may fall within the range of the deepest terrestrial mines.CITATION:McLellan, B C, 2015. Comparative life cycle impacts of deep ocean minerals and land-based counterparts, in Proceedings Third International Future Mining Conference, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015