Search Documents

BLAMEY STEVENS, Nogales, Ariz. (written discussion *).-This subject should be approached boldly from the purely physical standpoint. There are usually many known ways of making chemical deposits of any particular mineral and probably many more ways that are still unknown. With-physical-effects; .however, there-are, in-general, only one or two, or possibly three, ways that will pass muster before the physicist, when he realizes the geological conditions to be harmonized with the physical ones. Let us consider the second way that Mr. Taber describes: "It (the mineral matter transported in solution) may enter along a fracture, bedding plane, or similar passage, and, as it is deposited, force the wall rock apart, thus making room, for the growing vein," because it is the one Mr. Taber chooses for the great bulk of metalliferous veins. By "forcing the wall rock apart" Mr. Taber indicates that he means that the process of crystallization or-solidification of the mineral in the vein forces the walls apart. To prove this, he offers a great variety of geological evidence, which, from the physical standpoint, is entirely superficial. From the geological standpoint the evidence is the best to be had, but it is entirely negative and one single grain of really positive evidence will entirely offset it. Suppose it be granted that there is a considerable force of crystallization. It is well known among physicists that, other circumstances being equal, the crystal would rather form where it does not have to exert that pressure; or, to be more exact, where it is not necessary for the crystal to

Jan 12, 1918

By Carle R. Hayward

The growing importance of metallography has caused a corresponding interest in the improvement of apparatus for preparing specimens of metals and alloys for microscopic examination. The purpose of this paper is to describe an electric heating-furnace, a grinding- and polishing-machine, and a device for mounting specimens, which are used in the metallographical work at the Massachusetts Institute of Technology. These three pieces of apparatus were designed and made in the laboratory of the Institute, and each possesses some original features which may be of interest. Electric Heating-Furnace. The accurate control of heat necessary for metallographic work is best obtained by the electric-resistance furnace. Uufortunately, however, even the platinum-wound furnaces cleteriorate with use and ultimately burn out, while the cheaper resistance-materials are often short-lived. Since the resistance-coil must be replaced from time to time, it is of advantage to be able to make this change with as little trouble as possible, and this is an important feature in the furnace shown in Fig. 1. A is a cylindrical galvanized-iron can, with two handles, B. A porcelain tube, C, passes through the central hole in the cover of the can and rests upon the asbestos disk, D; the bottom of the tube is held in place by the asbestos ring, 3. The space, F, around the tube is filled with powdered magnesia. G is an ordinary assay-crucible, with the cover inverted so as to present a smooth top for supporting a second porcelain tube, H. The latter is wound with " Excello " resistance-tape, 0.014

Jan 1, 1912

By Theo B. Comstock

TO the large majority of visitors the unique features of the National Park are interesting chiefly on account of their novelty. Scientists of all schools may find here food for reflection, and much that is rare and marvelous; but the real, practical uses of the reservation, aside from its pleasure-giving adaptations, are not as yet fully appreciated. Since 1873, the writer has on frequent occasions expressed freely his own views upon the proper means of utilizing the Park for the best interests of science.* Some of the recommendations made have been adopted by the authorities. At the suggestion of friends I present here a brief statement of facts concerning matters which may be of advantage for visiting engineers to know, hoping that the very limited stay of the Institute may thereby be rendered a little more profitable, and that our common profession may possibly receive some benefit. First, then, it should be understood that, as in many other cases in. the West, the present routes to the Park from the south are not the most direct. The expedition of Captain (now Major) Jones in 1873 discovered a practicable route for a, wagon or railroad via the head of Wind River, through To-gwo-tee Pass and Two-Ocean Pass, by which the distance from Point of Rocks, Wyoming, on the Union Pacific R.R., to the Yellowstone Lake, is only 290 miles. Eventually, it is probable that a railway line from Cheyenne or some other point in Wyoming will be constructed, which, taking advantage of

Jan 1, 1888

By John D. Ridge, Robert C. Barwick

The amount of lead in concentrates that moved in international trade in 1952 was only 16 pct of the world mine production of lead and was less than 27 pct of the total of lead in concentrates and lead metal that traveled from one country to another. Because almost all lead is derived from galena, lead concentrates are high grade, with a theoretical maximum of 86 pct lead, and can be shipped as such without transporting a considerable weight of waste material. It would not be surprising, therefore, to find the large share of lead in international trade moves in concentrates (Rule 5). This is not, as has just been mentioned, actually the case. There is more than one explanation for the situation. Lead smelting is not a particularly difficult process and is one for which smelting equipment can readily be made of the best size for the tonnage to be handled. Another factor that encourages local smelting is the effort of many mining countries to see that a maximum of profit from their raw materials remains in the home country. Still another factor is the newness of large scale lead mining in two of the three largest exporters of lead in concentrates. In these countries, South West Africa and French Morocco, there has not yet been time to erect enough smelting capacity to process all of the concentrate output. Even in these countries, however, it will not be long, if present trends continue and plans are fulfilled, before most or all of the lead mined is domestically smelted.

Sep 1, 1955

Pumping coal to market may help Appalachian coal operators increase their share of the eastern seaboard fuel business. Transporting it by pipeline is already an accomplished fact, but until recently it had to be dewatered to be used in boiler furnaces. The campaign for these eastern markets was begun in earnest last November by the widely publicized announcement of successful plant-scale firing of a central station boiler with coal slurry pumped to the burners. This latest advance makes coal similar to oil and gas in convenience in handling and controlling at the consumption end of the pipeline. Slurry could be considered a new commodity for the fuel market. HUGE POTENTIAL MARKET The heaviest concentration of power plants in the U.S. is along the line Washington, Baltimore, Philadelphia, New York and Boston which makes this region the best hunting ground for selling pipelined coal brought from western Pennsylvania and northern West Virginia. Furthermore, if this region is assumed to consume 125 million tons of coal annually, on a comparable basis, the consumption of oil and gas would be about 180 million tons. Even if all of this fuel is not consumed in central stations, it is still a very big market for coal at the right price. Consolidation Coal Co. and Texas Eastern Transmission Co. are trying to line up customers in this area so that a pipeline can be built. This is not to say that there are not many other areas in the U.S. that could not be supplied advantageously by a mine-to-market pipeline.

Jan 1, 1962

Abadilla, Quirico A., Geol.. Lago Pet. Corp Box 172 Maracaiho, Venezuela. IIAbbw. Robert Graham. The W. W. Sly Mfg. Co.Train Ave.. Cleveland. Ohio. Abbotf A. N., Mines Supt., Maznpil Copper Co.. Ltd..Conception del Oro, Zac., Mexico. Abbotf Clarence E, Mgr.. Mines & Quarries, Tenn. Coal. Iron & R. R. Co., 1242 Brown Marx Bldg., Birmingham, Ala. Abbott. Louis Benjamin. Chief Engr.. Consolidation Coal Co. ... .Elkhorn Div., Jenkins, Ky. Abeel, George 8.. Jr., Cons. Min. Engr...4612 West 17th St., Los Angeles, Cal. Abel. Albert E.. Asst. to Pres.. Valley Mould & Iron Corp..Hubbard, Ohio. Abel. Raymond L Asst. Prof., Dept. of Pet. Refin.. Univ. of Pittsburgh. .. .Pittsburgh. Pa. Abernathy. George Elmer. Prof. of Geol. & Min.. Kansas State Teachers College. Pittahurg. Kans. Abernethy, D. Carl, Jr. Min. Engr., Hudson Coal Co. .Scranton, Pa. Abw, Hirouhi. Min. & Met. Engr., Min. & Met. Dept., The Higher Technical School, Osaka, Japan. Aborn. Robert H.. Research Assoc.. Mass. Inst. of Tech..Cambridge, Mass. Abouchar. Bylvain Sley. Min. Engr. & Geol., c/o S. H. Sekaly, 13 Rue El Nimr, Cairo, Egypt. tAbozeid. Mahmood. Pet. Min. Engr., Marland Oil Co. of California, Subway Terminal Bldg., Los Angeles, Cal. Abraham. Arthur W.A. pt. 40, Barcelona. Anzoatmui, Venezuela. Abrahams. Alexander I.. Gen'l Mgr., Racon Electrical Co.. ..... .Slough, London, England. tAbrahamuon, C. W., Min. Engr.. The Mond Nickel Co., Ltd.. ..... .Levack. Ont., Canada. Abstein, Henry T.. Engr. & Mgr.. Profile-Tamarack Mines Co.. ...... .Yellow Pine, Idaho. tAcker, E. WC.. Met.. ........ .I28 East Washington Lane. Germantuwn. Philadelphia, Pa. IlAckerman, D. E.. Research Engr.. Research Lab., International Nickel Co., Bayonne, N. J. tAckerman. Ernest R., Pres., Lawrence Portland Cement Co.. . .Plainfield, Union Co., N. J. Adachi. Jinzoo.A..d dress Wanted Adachi, Yuichi, Chief Engr.. Anzan Steel Works, South Manchuria RY. Co., Anzan, South Manchuria. China. (Via Dairen). Adair, Arthur C, Valuation Engr., Internal Revenue. Treasury Dept.. . .Washington, D. C. Adami. Arthur E., Prof. of Min. Engrg., Montana State School of Mines. Butte, Mont. Adami. Charles J.. Min. Engr., Gen'l Mnr., St. Jos~ph Lead Co.. ....... .Bonne Terre, Mo. Adama, C. W., Pres. Adams Pacific Corp .I66 Montgomery St., San Francisco. Cal. Adams. Cuyler .Dee rwood, Minn. Adams, David T, 514 Wrigley Bldg.. Chicago, Ill. ADAMS, FRANK DAWSON, Logan Prof. of Geology and Dean, Faculty of Applied Science. McGiU Univ., Montreal. Que.. Canada. Adams. Gale L, Research Engr.. General Pet. Corp...Los Angeles. Cal. Adams. George I.. Prof. of Geol. & Mineralogy. Univ. of Alabama. .Tuscalmsa, Ala. Adams. H. H.. Cons. Gml..Room 415, W. T. Waggoner Bldg., Fort Worth. Tex. Adams, Henry, Cons. Min. Engr. . 934 Park Ave., Plainfield, N. J. Adame, Henry H. 285 Madison Ave., New York. N. Y. Adams. Henry Farnum. Engr.. Charge Experimental Work, Inspiration Concentrator. Inspiration Cons. Copper Co.. Box 364, Inspiration. Ariz. Adams, Huntington, Min. Engr, 149 Broadway, New York, N. Y. Adams. Leland D, V.P.. Leslie-California Salt Co., 166 Montgomery St.. San Francisco. Cal. Adams. Louie W.. Illinois Steel Co Gary, Ind. Adama, XL L. Min. Engr.. Old Ben Coal Corp., Mine 12.. Christopher. IU. Adams, Robert M. Robert M. Adam Co. .I201 Fidelity Bldg., Duluth, Minn. Adams. Sidney F.. Geol., Empire Zinc Co .Gilman, Colo. tAdams, Waldo Peck..P ittsfield, Pike Co.. Ill. Addams. Charles 1. Min. Engr.. Bo x 663. Phoenix, Ariz. Addicka, Lawrence. Cons. Enar..... .61 Maiden Lane. New York. N. Y. Addison, Herbert, V.P.. Big Horn Collieries Co ,412 Colorado Bldg., Denver, Colo. Adkemn. J. Carson. Min. Engr.. HY Grade Manganese Co., Inc..Woodstock, Va. Ady. Joseph Wesley. Jr.. Min. Enar., 314 Mining Exchange Blda., Colorado Springs, Colo. Affelder. William Lewis. Asst. to Pres., Hillman Coal & Coke Co. & Allied Companies. 2006 First National Bank Bldg.. Pittshurgh, Pa. Ameck, B. F.. Pres.. Universal Portland Cement Co. .. .210 South La Salle St., Chicago. Ill. Agabeg, Edgar C.. Cons. Min. Engr.. ..... .Evelyn Lodae. Asansol, E. I. R. Bengal, India. tAsar. William M.. Aest. Prof. of Geol.. Kirtland Hall, Yale Univ.. ... .New Haven, Conn. Agaeniz. Rodolphe L, Pres.. Calumet & Hecla Consolidated Copper Co. ...... .Boston, Mass. tAgens, William Holmes. District Mgr.. Traylor Engrg. & Mfg. Co., 362 I. W. Hellman Blda.. Los Aneeles. Cal.

Jan 1, 1928

By J. A. M. van Liempt

SINCE the discovery, of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost' absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state

Jan 1, 1927

By AIME AIME

MOST of us are far .from home, and yet our Japanese hosts- have made us feel very much at home. Here in the Orient we engineers are .learning a new meaning for the word "orientation"- hereafter that engineering term will be a synonym for gracious hospitality, and "to orient" will mean to turn a whole country over to the World Engineering Congress. Mere geographic distance is no longer able to separate nations, for the conquest of distance is one of the triumphs of 'modern engineering. We of the Americas are fortunate in the position of our continents: with their shores lapped by the waves of two oceans, we face' two great civilizations, the' Occidental and the Oriental, and thus we can share the intellectual resources of these two older cultures.

Jan 1, 1929

By REED H. HYDE

IN these days of low metal prices and difficult marketing conditions, any treatment that will improve the grade of a product is of interest, particularly when the operation involves little or no addition to the total cost and may even result in a marketable by-product. Such a' combination of circumstances exists, in some cases, in the zinc industry, where it has been found that certain impurities can be removed from .the ore during the Dwight-Lloyd sintering operation, previous to reduction to metal. Consequently it is not surprising that zinc smelters having these sintering machines are paying particular attention to this phase of the operation. Loss of zinc as fume is very low under the conditions obtaining in sintering zinc ores, but impurities such as cadmium and lead are more readily fumed off and it is on this fact that the purification is based. As a result of preferential volatilization of these impurities a sintered product' is made from which purer zinc metal or oxide can be produced, while the fume may be collected and treated to recover the impurity metals. To be effective the operation must be carefully conducted, but no special equipment other than that of a well designed Dwight. Lloyd plant is needed.

Jan 1, 1931

By L. F. Reinartz

FROM the earliest times when our prehistoric ancestors laboriously fashioned crude tools and weapons from meteoric iron until our day when we manufacture steel in 150-ton open-hearth furnaces, the production of iron and steel has played a dramatic and important role in the development of civilization. Progress in the science of refining iron ore into iron and steel was painfully slow for many centuries. The keen scimitars of Damascus, the broadswords of the English knights, the coats of mail of French knights, and the Iron Pillar of Delhi are well¬known examples of medieval metallurgical technique. Expense and the scarcity of raw materials originally limited the distribution of iron and steel products. It was not until the nineteenth century that a determined effort was made to adapt the use of steel to peaceful pursuits. The spectacular and rapid strides made in the manufacture of steel during the last hundred years were hastened by the invention during the decade 1860 to 1870 of two great steelmaking processes-the Bessemer and the open-hearth process.

Jan 1, 1936

By L. F. Reinartz

The furnace in which rimming steel is made has an important bearing on the quality of the steel produced. Furnace.—Particularly in the manufacture of low-carbon rimming steels, it is necessary to have an efficient, easily regulated furnace, because of the relatively high finishing temperature requirements. In recent years, the most important development in design of open-hearth furnaces has been the sealing and insulation of the greater part of the furnace to prevent air infiltration and loss of heat. Efficient, straight-line valves insure proper draft. Combustion controls guarantee correct gas-air ratios. Furnaces of all sizes ranging from 20 to 200 tons have been used successfully in the manufacture of rimming steels. Metal bath is varied from 20 to 40 in. in depth without appreciable variation in quality. Charging.—A normal open-hearth charge consists of pig iron (hot or cold), scrap of miscellaneous nature, and slag-making additions, such as limestone and burnt lime. Because of local conditions, some plants find it necessary to discard the use of pig iron and use some carbonaceolis substances with varying percentages of cast iron to replace the pig iron. It is questionable whether such practice will consistently produce the quality of rimming steel required for auto stampings and other severe drawing requirements. Pig Iron.—An open-hearth furnace under proper control should melt 150 tons of low-carbon rimming steel on about 35 to 38 per cent pig-iron charge basis. In some practices, best results are obtained when the total charge contains from 0.40 to' 0.50 per cent silicon. If reasonably low-

Jan 1, 1935

By Thomas MacFarlane

IN smelting copper, lead, and silver ores, it is scarcely possible in every case to make analyses of the various parcels of ore, with the view of combining these and the fluxes so accurately as to yield, in the furnace, slags of exactly the most favorable composition. This is even more difficult with ores which require previous calcination, or with mattes which have been roasted in heaps. Even in cases where the greatest pains have been taken and the most elaborate calculations made beforehand, it frequently happens that variations in the working of the furnace interfere with the result so much desired. Generally, the practical metallurgist must be content with ascertaining the average composition of his ores and fluxes, making a calculation once for all as to the most advantageous mixture, and leaving slight changes in its composition to be taken care of as it is passing through the furnace. The various products then afford him the best material whereon to base his judgment as to the manner in which his smelting mixture is working. Of course the character of the slag is one of his chief guides, but it is not always possible from its outward characters alone to form a correct judgment as to its composition. Neither would it be possible or practicable to apply chemical analysis for this purpose, as it would be impossible to wait for its results while working a furnace. Abich was, I believe, the first to point out the relation existing between the composition of volcanic rocks and their densities, and to show that, the latter being ascertained, very correct conclusions

Jan 1, 1880

By Edward Thomas

THE late George S. Rice was active in the investigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and-to a lesser extent-Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,1 if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength2 in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable.

Jan 8, 1958

By Thomas MacFarlane

In smelting copper, lead, and silver ores, it is scarcely possible in every case to make analyses of the various parcels of ore, with the view of combining these and the fluxes so accurately as to yield, in the furnace, slags of exactly the most favorable composition. This is even more difficult with ores which require previous calcination, or with mattes which have been roasted in heaps. Even in cases where the greatest pains have been taken and the most elaborate calculations made beforehand, it frequently happens that variations in the working of the furnace interfere with the result so much desired. Generally, the practical metallurgist must be content with ascertaining the average composition of his ores and fluxes, making a calculation once for all as to the most advantageous mixture, and leaving slight changes in its composition to be taken care of as it is passing through the furnace. The various products then afford him the best material whereon to base his judgment as to the manner in which his smelting mixture is working. Of course the character of the slag is one of his chief guides, but it is not always possible from its outward characters alone to form a correct judgment as to its composition. Neither would it be possible or practicable to apply chemical analysis for this purpose, as it would be impossible to wait for its results while working a furnace. Abich was, I believe, the first to point out the relation existing between the composition of volcanic rocks and their densities, and to show that, the latter being ascertained, very correct conclusions

Jan 1, 1880

By N. W. Shed

The specifications for bridge-steel are usually not severe. The main difficulty is to secure a material which will roll easily, without showing signs of cracking on the corners of the blooms or on the flanges of the beams. In many mills sulphur has been deemed the most harmful constituent in this respect. It has been thought hazardous.to roll steel containing over 0.07 per cent. of sulphur. Yet, in making steel for the Phoenix Iron Company, I have produced from stock running as high as 0.13 per cent. of sulphur a material which rolled very satisfactorily. It is reasonable to infer that the injurious effect of sulphur can be neutralized, to a great extent, by proper treatment in the open-hearth furnace; and the following notes from my usual practice here may be of interest to those obliged to use high-sulphur stock. The steel made at Phoenixville in the 20-ton furnaces has about the following composition : Per cent. Carbon,...0.15 to 0.20 Manganese,.........0.50 to 0.60 Sulphur,..........0.11 to 0.13 Phosphorus,.: .0.04 to 0.06 Silicon,.......... 0.01 to 0.02 The best running heats were made with a small amount of pigiron. In using large proportions of pig the quantity of ore is also increased. This not only cuts the bottom, but also lengthens the time required to bring the charge down. Up to 50 per cent. of pig may be used, but 25 per cent. is much better. A 40,000-pound charge, containing 10,000 pounds of pig and 30,000 pounds of Bessemer butts or beam-scrap, works very well.

Jan 1, 1890

By L. F. Reinartz

The furnace in which rimming steel is made has an important bearing on the quality of the steel produced. Furnace.—Particularly in the manufacture of low-carbon rimming steels, it is necessary to have an efficient, easily regulated furnace, because of the relatively high finishing temperature requirements. In recent years, the most important development in design of open-hearth furnaces has been the sealing and insulation of the greater part of the furnace to prevent air infiltration and loss of heat. Efficient, straight-line valves insure proper draft. Combustion controls guarantee correct gas-air ratios. Furnaces of all sizes ranging from 20 to 200 tons have been used successfully in the manufacture of rimming steels. Metal bath is varied from 20 to 40 in. in depth without appreciable variation in quality. Charging.—A normal open-hearth charge consists of pig iron (hot or cold), scrap of miscellaneous nature, and slag-making additions, such as limestone and burnt lime. Because of local conditions, some plants find it necessary to discard the use of pig iron and use some carbonaceolis substances with varying percentages of cast iron to replace the pig iron. It is questionable whether such practice will consistently produce the quality of rimming steel required for auto stampings and other severe drawing requirements. Pig Iron.—An open-hearth furnace under proper control should melt 150 tons of low-carbon rimming steel on about 35 to 38 per cent pig-iron charge basis. In some practices, best results are obtained when the total charge contains from 0.40 to' 0.50 per cent silicon. If reasonably low-

Jan 1, 1935

General Aurelio Blanquet,* the best known of living Mexican soldiers, formerly the trusted friend of Porfirio Diaz and organizer of the old Federal Guard of Mexico City, who as a sergeant commanded the squad that executed sentence on Emperor Maximilian, and. more recently was Minister of War in the Cabinet of Victoriano Huerta, landed in Mexico early in April and joined the forces of Felix Diaz. His landing in the state of Vera Cruz, it was stated, was for the definite purpose of aiding the movement now under way to overthrow Venustiano Carranza and to place in power a government that will be "pro-Ally" in its sympathies and will promulgate and enforce laws that will guarantee the rights of life and property in Mexico. The New York Tinges says of the revolution editorially: "Whatever may be the success of General Aurelio Blanquet's attempt to overthrow the Carranza Government in Mexico, admiration cannot be withheld from the General's publicity manager. No enterprise awning at the overthrow of a Government ever had more favorable and widespread advertising. Felix Diaz, whom Blanquet is going to reinforce, supersede, or overthrow, as the case may be-Mexican precedent in these matters offers opportunity for considerable speculation-has been conducting his revolution, at the old stand for some time, but without much success. But, says General Blanquet's representative, the landing of Blanquet will send a thrill to the heart of every true republican.' Meanwhile a biographical booklet is published, adorned with photo¬graphs illustrating the General's record, including such varied matters as the General in favor, receiving a decoration from Victoriano Huerta, and the General in exile, feeding the birds in Central Park."

Jan 5, 1919

By Howard Drullard

To OBTAIN the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the 'chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not, adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid-grease should be used. The lubricators should be filled-once for every 12 or 14 ft. (3.5 to 4m.), of hole drilled. Grease-guns should be used to fill the port in the chuck end once a shift; a medium ( No. 3) grease is well adapted to this purpose. Hard grease must not be put into- the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of, hole drilled. The rotating handle of a stoping drill -is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wicking, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at. least twice a shift; lighter oils than castor, such as Arctic Ammonia may be used.

Jan 8, 1920

By Van Manning

IN SUBSTANCE, the international aspects of the petroleum industry, as these relate to the United States, are as follows: The domestic production is not keeping pace with the domestic demands; our best engineering talent warns us of the imminence of a decreased production by our oil wells, although more oil is needed; and the only practical source whence this increasing demand can be supplied for some time to come will be the foreign fields. Other nations have given thought to the future and, in recent years, have shown a tendency to adopt strong nationalistic policies regarding their petroleum resources, policies that hinder or prevent the exploitation of these resources by other nationals. In consequence, we find that, facing a probable shortage of the domestic supply, our nationals are excluded from foreign fields; and this in spite of the fact that foreign nationals have been permitted to enter into and exploit, our own oil resources on an equality with American citizens and without hindrance or restrictions. This country: has supplied the larger part of the petroleum consumed by the world and yet, with a failing supply imminent, it finds that those countries that have been drawing upon our resources to supply their needs are showing a tendency to exclude us from their resources. In this way we shall be transferred from a position of dominence to one of dependence; and only by sufferance of those countries that are now seeking financial or political control of petroleum supplies, shall we be able to obtain the oil we will need.

Jan 2, 1920

Mr. Cottrell : I omitted to speak of the cost of installation. The precipitation-plant at the Balaklala smelter, up to the time of initial operation, including the construction of flues, installation of the apparatus, etc., cost $107,000, and subsequent modifications probably represented at least $15,000 more. Upon the information gained in this plant, the installation at the cement-mill, handling nearly twice as much gas, has been reduced in cost in a number of ways, but the overhead construction, carrying the precipitator at the top of the stacks, is naturally expensive, yet, even so, the total cost of construction will probably not greatly exceed $150,000. The mechanical details of the tubular form last shown have been worked out more recently than those of the plate form, and the tubular form promises to be still less expensive in construction, as you would naturally expect. The cost of operat-ing the plant varies somewhat with the character of the gases used. The amount of power consumed is not determined by the tonnage of the material collected, but by the volume of gas to be handled. It takes as much power to precipitate a thin cloud as a dense one. In the cement-plant they are getting a higher efficiency; i. e., a greater number of cubic feet treated per kilowatt than in the earlier plants. This is perhaps partly due to higher temperature of the gases, which here average about 450° C. The best figures on the cement-plant are between 3 kw. and 4 kw. Of

Jan 1, 1913