Search Documents

By R. L. Ash, R. R. Rollins, C. J. Konya

An investigation was performed to determine conditions for optimizing the spacing of simultaneously initiated multiple explosive columns. This was done by using models of mortar, dolomite, and Plexiglas with 10-grain mild detonating fuse as the explosive charge. It was desired to simulate blastholes with multiple primers initiated by detonating fuse or when high-velocity explosives are used in low-velocity materials. It was found that optimum spacing between multiple charges was strongly influenced by charge length. At less than optimum charge length, the spacing at which complete shearing was possible between adjacent charges decreased exponentially with a subsequent loss of broken material volume. For charges fired simultaneously, larger burdens and spacings were possible as compared to those necessary for single-crater charges. For each material studied, there was a characteristic optimum charge length and a maximum attainable spacing at any given burden. Proper selection of the spacing distance between charges is fundamental to successful blasting. Its value directly affects the cost of drilling and explosives used per unit of broken material. In addition, the choice of a spacing that is Compatible with a given set of blasting conditions aids in the control of fragmentation sizing, ground vibrations, overbreak, and throw which in turn, influence other production costs. For example, normally loaded blastholes that are spaced too closely invariably promote overbreak and usually give coarse fragmentation. Unless care is taken, airblast and violent flyrock will occur and under certain conditions cutoffs and misfires may result. Too large a spacing, on the other hand, frequently leads to conditions that form bootlegs or toes. The choice of a particular spacicg to use, however, is largely a matter of individual experience and judgment, usually based on trial and error. Very little is known or can be found in the literature with regard to how the spacing between charges is related to field conditions and charge geometry. As a general rule, the firing time sequence of adjacent charges and properties of a material are thought to have the most significant influence on the spacing distance best suited for any given field condition. For example, delayed initiation of adjacent charges usually always requires a closer spacing than when charges are fired at the same time. This should be expected if one considers that the energy normally dissipated and lost in the surrounding ground from charges fired independently would be captured and utilized for breaking material between charges when they are initiated together. Spacing can be extended also when charges are aligned with structural planes of a material, such as jointing, along which shearing is relatively easy. It is customary to relate the spacing (S) between charges to their common burden (B) in the form of a spacing ratio, or SIB. The burden normally is considered as the optimum depth or distance from any single charge perpendicular to the nearest free or open face at which the desired fragmentation and maximum crater yield are obtained. For production blasting, value of the ratio is generally considered to vary from 1 to 2, depending on conditions.1-6 When adjacent charges are fired independent of one another, the value varies from 1 to about 1.4, the closer amount being employed to square corners or produce craters having the ideal 90" apex angle. The larger ratio is the geometric balance value for craters having an apex angle of 135". The basic ideal crater forms in the plane of the charge diameter for charges fired independently are shown in Fig. 1. In the event charges are fired simultaneously, geometric balance in the plane of their charge diameters suggests that a spacing ratio near 2 would be appropriate, as illustrated by Fig. 2. In practice, however, some compromise ratio value must be selected to conform with the specific ground conditions. An example would be where the jointing planes tend to produce 60° or 120° crater angles, the appropriate geometrically balanced charge arrangement being given by Fig. 3. In this condition, the spacing ratio is 1.15, not 1 or 1.4 as suggested for the 90° cratering of independently fired adjacent charges. In view of the foregoing, it would seem logical to assume that whenever charges all having the same burden are fired at the same time, spacing distances always can be greater than those permitted by charges fired independently. In practice this is not the case, however.

Jan 1, 1970

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,',' Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to in- crease. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining

Jan 1, 1981

By B. A. Wilcox, A. H. Clauer

DURING the course of an investigation on the high-temperature creep behavior of TD Nickel* (Ni + 2) vol pct ThO2), it was observed that the creep fractures were similar in appearance to low-temperature ductile fibrous fractures and creep ruptures by cavitation. Microfractographs of fibrous ruptures are typically characterized by a dimpled appearance, with second-phase particles frequently found near the bottom of the dimples.'-4 These somewhat resemble creep ruptures by cavitation, in that fracture occurs by void formation, with the subsequent growth and final merging of the voids to form a complete fracture.' It is the purpose of this communication to describe the creep fracture of TD nickel and suggest a mechanism for the rupturing process. The discussion is relevant to material crept to fracture in vacuo at a constant stress of 18,000 psi, over the temperature range 900" to ll00°C. The material used in this investigation was 1/2-in.-diam bar stock supplied by Du Pont, contain- ing 2.3 vol pct Tho2. The final fabrication treatment consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fibered structure with a transverse grain size of -1 µ and a longitudinal grain size of 10 to 15 µ. Selected-area diffraction indicated that the fiber axis was parallel to (00l), in agreement with the results of Inman et a1.6 The thoria particle size varied from 80 to 1000Å, with an average size of 400Å, and the mean particle spacing was about 1200Å. The remarkable structural stability7 was confirmed by annealing for 6 hr at 1300°C (about ' 0.9 the absolute melting point). Transmission electron microscopy revealed that the only structural change was a slight decrease in dislocation density. Furthermore, recrystallization or grain growth during creep has not been observed. All specimens were annealed in vacuo at 1300°C for 3 hr prior to creep testing. The following times to rupture were obtained for vacuum creep tests at a constant stress of 18,000 psi: 900°C, 854 hr; 930°C,

Jan 1, 1965

By Roman Y. Poderny, Vladimir V. Rjevskii

In the USSR, the Moscow Institute of Radio Electronics tronics and Mining Electro-Mechanics (MIRGEM) has started what it hopes will become a nationwide movement to educate mining students in the precise specialties that industry has come to require. Courses for mining engineers, the MIRGEM faculty proposes, should dovetail as exactly as possible with specific jobs available in the mining profession. Acting upon this thesis, MIRGEM revised its own curriculum in 1962 and has since presented an over-all plan for Soviet mining education before two mining school conferences as well as the Ministry of Higher Education and a number of major Soviet industrial ministries. The plan was universally approved with some suggested revisions. SOVIET MINING EDUCATION TODAY At present, mining education in the Soviet Union covers the exploitation of solid minerals and raw materials, including coal as well as ferrous and nonferrous metals. The extraction, storage, and refining of oil and gas is treated as a separate discipline. In all, there are 33 Soviet universities and institutes that train mining engineers for careers in the industrial, research and educational fields.

Jan 9, 1966

By J. T. Ryan

POISONOUS, irritating, or explosive gases are found in almost every industry, and manufacturers of gas masks are called upon to provide gas mask protection for a great variety of conditions, such as operators in horseradish factories, fumigators of homes and ocean liners, and men engaged in the manufacture of tetra-ethyl-lead, the new motor fuel. The modern type of gas mask and respirator, to provide protection against all such industrial gases, is an outgrowth of the gas mask developed during the World War to protect the soldiers against the poisonous war gases. So far, it has been possible to develop ample mask protection from all known noxious gases and fumes present in atmospheres encountered in mines, metallurgical works, and chemical and other industries, so long as there is sufficient oxygen present to support the flame of an oil lamp. The most important development of the gas mask was in providing protection against carbon monoxide- which is the noxious gas that mining men are most concerned with and, in fact, is the noxious gas that man is most frequently exposed to. This paper will be con- fined largely to the discussion of masks for underground use in metal mines. Gases that contaminate the normal air in mines can be divided into two classes: those that are given off normally by the workings, and those that are produced in mine operation.

Jan 1, 1926

By G. F. Tagg

Earth-resistivity measurements are often of service in obtaining information regarding geological formations, particularly when applied to structural problems. In such problems the masses of the various bodies are large, and have a corresponding effect on the average resistivity of the soil. Much work has been done using such measurements, but in general the method of interpretation employed is empirical. Since certain simple cases can be investigated mathematically, it appears to be quite sound to endeavor to apply the mathematical solutions to the practical results, in order to deduce from the latter such unknown quantities as depth. This paper deals with such a method of interpretation for the simple case of a single horizontal stratum. In the method described by Wennerl for measuring earth resistivity, four stake electrodes are driven into the earth in a straight line as shown in Fig. 1. A current I amperes is passed between the two outer stakes and the potential difference V volts between the two inner stakes is measured. Then if a is the electrode separation, the specific resistance of the soil, which is assumed to be homogeneous, is given by the formula P = 2?v/1 [1] v or if v/1 is called a resistance R ohms, p = 2?aR [2] If a is in inches, p will be in ohms per inch cube, or ohm-inches, and if a is in centimeters, p will be in ohms per centimeter cube or ohm-centimeters. As stated above, this formula is true only if the earth is homogeneous, and when this is not the case an application of one of these formulas

Jan 1, 1934

By D. Harker, M. J. Murphy

THE mechanism by which age-hardening takes place is still not completely understood. The principal theories range from the extreme of "precipitation-hardening" to that of "order-hardening," with many intermediate gradations. In the hope of obtaining new data on which to base a choice among the many theories, the authors have made electron micrographs of formvar replicas taken from metallic specimens at various stages of age-hardening. The results so obtained on an alloy of 2 per cent beryllium in copper and one of 20 per cent molybdenum in iron will be described in the following pages, as well as the technique used in preparing the replicas. PREPARATION OF FORMVAR REPLICAS OF METALLIC SPECIMENS This section is concerned with the techniques that have proved successful in preparing formvar replicas for studying the microstructure of metals with the electron microscope. Because of its simplicity and accuracy, the formvar replica1 method developed in the General Electric Research Laboratory has been used exclusively, since it is much simpler than the silica replica method of Heidenreich and Peck2 and produces as good results. The formvar method to be described requires a technique acquired only by practice, and no foolproof set of rules can be given. It is a rapid method and a replica can be obtained in less than five minutes under favorable conditions. This does not mean that perfect replicas can be produced every five minutes, but rather that one can well afford to take several strippings* in order to produce a replica of high quality. The metallographic technique required for replica work-very fine polishing and etching with very dilute solutions-is described here. It can be said, in general, that almost any surface that has been carefully prepared for a photomicrograph at 1000 or more diameters can be used to obtain a replica for the electron microscope. PREPARATION OF METALLOGRAPHIC SPECIMENS The preparation of the metallographic specimens is somewhat more exacting than that usually given to samples to be used for inspection under the light microscope. After much experimentation, it was concluded that the best method consists in polishing the metal through to the coarse cloth, then etching and repolishing on final cloth until the layer of distorted metal is removed. After this procedure has been completed, a dilute etch-to approximately the depth necessary for a micrograph at 1000 diameters-usually produces a sur-

Jan 1, 1945

Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 T A Read, Chairman O T Marzke, Past Chairman J H Jackson, Senior Vice-Chairman David Swan, Vice-Chairman D C Johnston, Secretary-Treasurer AIME, 29 West 39th Street New York 18, New York

Jan 1, 1960

By T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 91. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special condi¬tions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1943

By C. C. Miller, A. B. Dyes

The cost of finding and developing new reserves is continually rising. We must meet these rising costs with more economical operations. This can he accomplished if we revise our ideas of proper well spacing and well allowable to consider the concept of optimum well spacing. According to this concept, the optimum spacing is the one which leads to the maximum present worth for a reservoir when ail factors affecting total cost and total revenue are considered and when the wells are produced in the most eficient manner. Application of this principle efficiently utilizes available well potential and properly considers the recovery eficiency in addition to fixing the spacing on the basis of the amount and value of the oil to he recovered. This Study presents an analysis of one producing zone containing low gravity crude to illustrate the effect of these factors on the present worth and on the optimum economic spacing under two production drives—-evolved gas and water drive. The maximum present worth occurs when the optimum number of wells for open-flow operation is employed. Frequently, this optimum development cal1s for very wide spacing and the ideal field rates are not unreasonable. Under other circumstance. where proration is necessary, an optimum combination of well spacing and well allowable exists which permits production at relatively high rates. The optimum well density in a field depends on the recovery efficiency and the valule of the oil. In solution gas-driven reservoirs this optimum spacing for operation at high producing rates can vary from extremely wide spacing to handle viscous low gravity oil in thin formations to relatively close spacing in thick sands where good recoveries are expected. Because of the better recovery from water-driven fields, the optimum spacing in these fields is closer than in solution gas-driven fields. Also, the water encroachment pattern is dependent upon the well spacing, and an adequate numher of wells is needed to assure a good sweep eficiency. The economic optimum well density in a water-driven field is high enough for this purpose. INTRODUCTION From year to year domestic oil becomes more difficult to find. The fields we do locate are frequently smaller and deeper than older fields and the costs for men, material and equipment are continually rising. To replenish our reserves we must continue to search for and develop new fields, but experience has shown we cannot expect prices to rise in proportion to costs. Consequently, we must meet increasing costs by more economical operations. A vigorous effort is being made within the industry to improve exploration methods, to cope with the problems of deeper drilling, and to obtain a secondary yield from older fields. Many significant contributions have resulted from these efforts. The economic operation of new fields can be further improved by developing these fields on optimum spacing and producing the wells at higher rates. This would avoid the drilling of unnecessary wells and provide additional capital for seeking new oil. While the benefits of these practices are obvious, the problem of defining the optimum development of a field for natural depletion can become very complex. A study of the effect of well spacing and several reservoir variables on economic worth of a specific field is reported here to illustrate the problem and to show the magnitude of the benefits to be realized. This study is necessarily limited to the field conditions selected and is not intended as a general solution of the well spacing problem. It does, however, indicate factors to be considered, the trends to be expected, and the direction in which we should proceed in developing new fields. NO consideration is given to land and legal considerations which might arise. METHOD OF ANALYSIS The optimum method of developing and producing a field is to use the combination of spacing and prora-tion which gives the maximum return. In addition, we do not want to lose recovery. These considerations of maximum return and maximum recovery present no serious conflict. The value of each method of operation is conveniently expressed in terms of its present worth. According to the present worth method of evaluation,' an acceptable annual percentage return is assigned to the operation, and all incomes, capital costs, and expenses are discounted at this rate to the start of the operation. This net value is the present worth. If we apply the same discount rate to several alternate methods of operation, the one yielding the greatest present worth is the best method. If we express net income in terms of price per barrel of oil produced, drilling and equipment costs on a well basis, and expenses as cost per well year, this evalu-

By L. W. Casteel, E. A. Jones

MINING the lead deposits of Southeast east Missouri has reached a high stage of technical development dictated by the scattered occurrences of low-grade ore through favorable horizons in the Bonne Terre formation. The rock-breaking, handling, and related practices described here have evolved as the best way of mining these particular deposits. These methods are applied in the production of about 19,000 tons of lead ore per operating day from four mines in Southeast Missouri. Development drilling Drifts 10 ft wide and either 8 or 9 ft high are driven in this district on contract. Miners are guaranteed standard wages plus a bonus on the footage advanced, if earned. Labor, fuse, caps, wire, and dynamite used are charged against the contract. Normally the cycle of operations in drifting is performed by a two-man crew, a motor operator and a shovel operator who first load out the rock broken by the preceding shift. The drift crew then sets up two vertical column and mounts the drills. Cleveland HC-10's are used which have a steel lug integral with the cylinder for connection with the air feed. All drilling in drifts is wet. Air pressure is 85 to 100 lb at the face. From 28 to 32 holes are drilled per swing in a pyramid cut. Cut holes

Jan 1, 1947

By T. B. Massalski, Horace Pops

Martensitic transformations were observed by optical metallography and electrical-resistivity measurements during cooling at cryogenic temperatures of the bcc pr-phase Au-Zn alloys. The com-position dependence of the MS, MF, AS , and AF temperatures have been determined. It is concluded that the martensitic platelets which grow mainly in the lengthwise direction and which are associated with a very small temperature hysteresis are "thermoelastic" martensite. In some cases the observed structure seems to have no definite crys-tallographic habit or consists of a mixture of- plates and broad transformed areas. THE majority of the bcc /3-phase alloys in systems of copper, silver, and gold with zinc and cadmium are unstable at low temperatures and undergo a transformation upon further cooling into another structure. A large number of such transformations are martensitic. The composition dependence of the Ms temperatures has been determined and reported for CU-~n,' Ag-Cd,' and AU-C~~ alloys. The 50 at. pct ordered Au-Zn p' alloy has been reported by Jan and pearson4 to transform martensitically at 58°K in connection with their study of the de Haas-van Alphen effect The p' phase in the Au-Zn system has the ordered CsC1-type structure. The phase field is shown in Fig. 1: it has the typical V shape which is characteristic of all copper-, silver-, and gold-based binary /3-phase alloys. There appears to be no a priori reason why the transformation should be limited to the equiatomic composition and the availability of a cryogenic stage for optical metallography5 has permitted studies down to the liquid-helium temperature of a series of alloys in this system. EXPERIMENTAL PROCEDURE Predetermined weights of 99.999 pct pure gold and zinc were melted and cast under a partial atmosphere of helium in sealed quartz capsules. Thorough mixing of the molten metals was achieved by vigorous shaking, followed by a rapid quench into a brine solution. All ingots were homogenized at 640°C for 4 days. The loss in weight was usually less than 0.04 wt pct and was assumed to be due to

Jan 1, 1965

By T. T. Read

FOR the second time the Mineral Industry Education Division opened the sessions at the Annual Meeting by gathering at the Engineering Woman's Club, Sunday at 3 p. in., and, in spite of the informality of the hour, with a good attendance of representative men in the educational field. The chairman of the Division, Thomas T. Read, after briefly reviewing some of the more significant events of the past year, introduced H. P. Hammond, professor of civil engineering, Brooklyn Polytechnic Institute, a leading figure in the project of the Engineers' Council for Professional Development for accrediting engineering schools. Prof. Hammond made it clear that the project is not to rate engineering schools but to accredit them; not to arrange them in order of excellence, but to segregate them into two groups, those that are entitled to recognition as genuine engineering schools, and those that are not. About thirty schools in the whole country will presumably fall into the latter class; they are typified by an unnamed institution where the teacher of mathematics bears the title of Professor of Civil Engineering and the man who teaches chemistry that of Professor of Chemical Engineering, and having no engineering instruction except some elementary surveying, but still claiming in its catalogue to be an engineering college. While everyone would like to avoid the necessity of accrediting engineering colleges, it cannot be avoided, since the University of the State of New York, and several other agencies, are already doing it. If it cannot be avoided it is best that it should be done by a qualified agency set up by the national engineering societies, so that the results may command respect and general acceptance. It is for this reason, and this alone, that the accrediting committee of the E. C. P. D. has been set up. It is now ready to begin its task, and during-the coming year it will accredit the schools in two of the seven geographical districts into which the country has been divided, beginning with New England and the Mid-Atlantic States.

Jan 1, 1935

By H. B. Pulsifer

ABOUT 15 varieties, or modifications, of the best magnesium available were prepared and subjected to etching tests, then examined for microstructure. Of the 30-odd etching reagents that were tried, nearly half, mostly ammonium salts, etched the metal satisfactorily. The surfacing and etching of magnesium is shown to be a very simple and quick operation. The density and hardness of magnesium were determined. The most interesting new observations relate to the finding of the hexagonal etch figures, the crystal laminations, and the fact that the metal is plastic, cold, when restrained or quickly deformed. Under slowly applied pressure cold metal deforms slightly, then shears to fracture without plastic flow. The chief structural features of magnesium are presented in two reduced photographs and 30 photomicrographs. MATERIALS TESTED There are only two sources in the United States from which new metal can be procured: the American Magnesium Corpn. and the Dow Chemical Co. No pronounced structural or property differences in the metals from these two companies were disclosed by the work of this investigation. The following materials were obtained from the manufacturers: 1. Massive crystals of distilled metal (American Magnesium Corpn.). 2. Rods of hot-extruded metal, ½ -in. squares and 5/8-in. rounds (American Magnesium Corpn.). 3. Sheet magnesium, 0.005-in. thick (American Magnesium Corpn.). 4. Cast stick metal, 1 3/8-in. dia. (Dow Chemical Co.). 5. Magnesium-aluminum alloy, hot-rolled plate, ½ in. thick (American Magnesium Corpn.). From these materials, were prepared: 6. Sections from a furnace-cooled ingot made from distilled crystal. 7. Cold-strained pieces from (6), (4) and (2). 8. Pieces cold-squeezed to fracture from (6), (4) and (2). 9. Hammer-struck pieces from (6), (4) and (2). 10. Steam-hammer struck pieces from (6), (4) and (2). 11. Sections from furnace-cooled ingot of the magnesium-aluminum alloy.

Jan 1, 1928

By Robert Mehl

THE purpose of this investigation was to prepare high-purity iron-carbon alloys, to determine as precisely as possible the A3(GOS), the Acm(SE), and the A1(PSK) transformation temperatures in the meta-stable iron-iron carbide system (up to 1.4 per cent C), and to study the influence of carefully controlled and constant rates of heating and cooling (1/8 to 2° C. per minute) upon the transformation temperature and upon the resulting microstructure. Apart from the general metallurgical importance attending the completion of such a task, it will be noted that highly precise transformation temperatures are of interest and importance in the thermodynamic study of this system1. Several determinations of the iron-iron carbide diagram have been made. These suffer generally from the low purity of the alloys used, and from the application of methods of investigation of low sensitivity. Attempts to compare and weight the many data available in an effort to construct as accurate a diagram as possible have, in the main, been unsuccessful. In general, the wide differences in the results of different workers, the lack of complete analytical data, the omission of important details relating to the heat-treatment of the alloys, and the meager description of the methods of investigation applied, render such a process of averaging nearly meaningless. It may be seen from the summaries by Epstein2 and Körber and Oelsen1 that variations as great as 30° C. exist in the reported data on the A3 temperatures in iron-carbon alloys. For-tunately, the A3 temperature in pure iron is now known to be 910° C. ± 1° C.3 The best recent work on iron-carbon alloys is that of Esser4 on hypoeutectoid steels and that of Sato' on both hypoeutectoid and hyper-eutectoid steels.

Jan 1, 1937

By Walter C. Lawson

THE primary objective in laying track in panel sections is to reduce the number of track laborers required. This is possible because the work is mechanized. Moreover, because the work is mechanized and each of the operations needs only a few men, and each is self-contained, the work can be carried on at night as well as in daylight; therefore, the method provides a means of preparing tracks on more than one shift. The laying of tracks in open pits and quarries in panel sections is not new but new methods have been made possible by the introduction of new types of equipment. The purpose of this paper is to describe the methods that are followed in' the Morenci open pit. GENERAL MINING OPERATIONS Full-scale ore production at Morenci is about 50,000 tons daily. The normal yearly output of ore and waste is 32,000,000 tons, of which 30,000,000 tons is handled by rail haulage. This requires the building of approximately 47 miles of loading and other temporary tracks during a 12 months' period (Fig I). Broken ore and waste, is loaded., into 90-ton capacity dump cars with 5-cu-yd full-revolving electric shovels. Shovel banks are uniformly 50 ft high:. They are blasted- with churn drill holes, and the broken material from a blast is loaded out with two shovel cuts, the first one being called (locally) the "splatter" cut and the second one the "clean-up" or "face-up" cut. When a shovel is making its clean-up cut, the loading track is about 70 ft from the toe of the bank and, under normal conditions, a bank is blasted against it without removing the track. It is thus evident that each track is used for two shovel cuts before relocation is necessary, inasmuch as a single position serves for both the clean-up cut prior to blasting and for the splatter cut following the blast. The normal advance of a solid bench by a single blast is 40 ft (Fig 2). PREPARATION OF PANEL GRADE In preparation of panel grades bulldozers and rooters are used for the bulk of the work and an auto-patrol road grader for the final stage. At Morenci, bulldozers have always been used for track-grade preparation, but before the introduction of the other two types of equipment grades were uneven and irregular at best, and always necessitated a big gang of track laborers to hand-block under the ties with rocks after a track was laid into place. High blocking also made poor track because of instability and caused frequent derailments. Under these conditions derailments were generally bad as re-railing became difficult. Much track was torn up and many ties broken in the process. The inadequacy of the hand-blocked track, together with the inefficiency of hand blocking, constantly pointed to the desirability of reducing the amount of labor required, so various means were tried to improve conditions, such as wood

Jan 1, 1947

By L. C. Graton

At the Tenth International Geological Congress, Mexico, 1906, Waldemar Lindgren presented "The Relation of Ore Deposition to Physical Conditions." Retrospect ranks it as the outstanding offering at that Session and as the most fundamental contribution up to that date on the philosophy of ore deposition. Elaborating thereon in his text-book "Mineral Deposits," Lindgren analyzed ore-forming processes under conditions prevailing from great depth up to surface; explained the nature of deposition in each environment; and developed a comprehensive genetic ore classification, which brought wide acceptance and enriching contributions by many. Since Lindgren's latest edition (1933), have come wealths of material relevant to ore genesis, particularly through amazing renaissance and proliferation throughout science. Current publication regarding ores now emanates largely from a generation caught in pressures of the breathless modern tempo, which tempts scant reflection upon earlier truths. Consequently, today's thrilling output contains not a few offerings that need challenge because supplanting interrelationship and system by what seems, collectively, an assemblage of strange, ad hoc and often self-contradictory concepts. From these latter some merit may eventuate but at the probable cost of present confusion and delayed progress. The following pages, naming numerous post-Lindgren advances, record the conviction, held by many, that Lindgren's philosophy, progressively improved, remains the soundest approach to understanding ore genesis.

Jan 1, 1968

By James M. Link

The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple compared to the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve the understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instances, more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test loops such as the one at the Colorado School of Mines Research Institute. The pilot scale projects are designed to provide the basic engineering data necessary to design slurry transport pipeline systems. Usually three slurry solid concentrations are pumped at various line velocities and optimum slurry densities and velocities are determined. Critical velocities, friction head losses, power requirements, and so forth, are also determined from measurements and calculations. Wear tests are also strongly recommended and anticipated pipe wear rates in inches per million tons of solids reported.

Jan 11, 1972

By T. A. Wilson

THE plastic deformation of slender single crystals of zinc has been described in some detail in the paper by Mark, Polanyi and Schmid,1 which has become a classic, and also by one of the present authors in a somewhat shorter account.2 The study of single-crystal zinc is termed classical because zinc single crystals offer, perhaps, the best material yet available for the study of atomic behavior during deformation and the effect known as "strengthening" in metals. A considerable amount of additional work has also been clone on single-crystal zinc, but as it 'is not closely related to the present paper it will not be considered. Throughout all the former work, the mechanism of plastic deformation first described by Mark, Polanyi and Schmid has been assumed to hold. This may be said to offer the strongest confirmation of its correctness. Even so, the picture of the process has never been as completely portrayed as is desirable. The first object of the present paper is to describe work that has been done in this field, and which is even yet being carried on, in the hope that a more complete picture may be obtained. Mathewson and Phillips3 have recently described a new mechanism of the deformation of zinc based on their study of large rectangular crystals. One of their conclusions was that deformation produced twinning with a rotation of some of the basal planes into positions 94° removed from their original position; a position almost the same as that of the prismatic planes before twinning. A second conclusion was that fracture occurred along these basal planes in their new position, and, therefore that fractures previously regarded as prismatic were in reality basal. Such findings are of great significance and they raise a question as to the generality of such behavior. Professor Mathewson's opinion is that even the slender cylindrical single crystals behave in the same manner as his large rectangular crystals when strained by simple tension.

Jan 1, 1927