Search Documents

By Remo Grandori, Manfred Jaeger, Fabrizio Antonini, Luis Vigl

The EVINOS-MORNOS tunnel project with its 30 km of length is one of the longest hydraulic tunnel in the world realised with TBM method. The adverse geological conditions, the high cover and the short construction schedule were a great challenge for the successful construction of this tunnel. The paper will describe: the criteria adopted for the tunnel design, the selection of the construction methods and equipment, the productions of the 4 TBMs adopted and the comparison of the behaviour of the different type of TBMs in the various rock conditions, including special conditions, the characteristics of the adopted in situ and precast linings, a comparison between the foreseen and actual construction schedules, the contractual implications of realising a tunnel in such a severe and complex conditions.

Jan 1, 1995

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

By R Shaw, M Hidding

The design of primary sample cutters for high-capacity conveyors is critical to achieving a correct sample, both in collecting the sample and ensuring smooth sample discharge flow. Modelling usually occurs at the design stage and requires extensive experience to achieve the correct result. However, it is difficult to confirm the effectiveness of the cutter design until after installation. Even with high-speed video, confirmation of complete sample capture is difficult, especially if the material characteristics change over time. Recent investigation using discrete element method (DEM) simulation to model the flow of the ore into the cutter and observe how it interacts with the cutter has revealed some interesting design requirements not observed in the past. By including DEM modelling, the correct design and optimisation of the cutter can be more accurately determined prior to commissioning.CITATION:Hidding, M and Shaw, R, 2017. Modelling ore flow in the design of high-capacity sample cutters, in Proceedings Eighth World Conference on Sampling and Blending , pp 145–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By J. H. East, D. Harrington

"INTRODUCTION Mining at its best is not a clean occupation for either surface or underground employees; and this applies alike to coal, metal, and non-metallic mines. The employees are handling minerals that have been blasted, or broken by some means and are subjected to mineral dust, whether it is coal, quartz, or talc. The employees usually wear clothes specifically adapted to the work in which they are engaged, and frequently these clothes are not suitable for use away from the mine. Many mines are wet, and employees must wear rubber boots to remain at least partly dry, and even on relatively dry mines, some parts of the mines usually have water falling from overhead, there are accumulations of water, or the floor or other surfaces are wet or muddy, Some mines are dusty, and the air-borne dust quickly settles on the clothes and body of the miner, especially, when he is working in confined areas, or in places that are hot, humid, or poorly ventilated. Most occupations around a coal tipple, anthracite breaker, or a mill at a metal or nonmetallic mine have their own problems of cleanliness as to skin or clothes or both. Mining in any of its phases is inherently dirty work, and the employees dress accordingly while at work.In the early stages of mining it was the custom or workers to wear their dirty clothes home and change there. This necessitated their going home after work in dirty clothes which were usually damp from perspiration or from contact with wet or muddy matelials or surfaces, and, in addition to being inconvenient this was a frequent cause of colds, pneumonia, other pulmonary diseases or, possible skin ailments. Men working in very wet mines found that it was more satisfactory to change into dry clothes in the boiler room at the mine after work and allow their wet clothes to dry overnight. The mining companies later provided the first of the so-called ""dry-houses"" which were heated but had, few, if any, conveniences, such as showers, lockers, or latrines. The miners changed into dry clothes after work, but would not bathe or ""clean up"" until they reached their homes. Later, progressive mining companies provided bathing facilities for the employees, and eventually the present modern wash and change houses were evolved. Unfortunately, many mines, still have no bathing accommodations, and many have only makeshift accommodations."

Dec 1, 1947

By D Brett

"Mine waste storages including tailings dams and waste rock dumps represent arguably the biggest risk on a mine site from both physical and geochemical viewpoints, related firstly to structural stability and the consequences of failure and secondly from potential on-going seepage or run-off of acid and metalliferous drainage (AMD). The risks are most likely to increase during operations and continue through the closure and post-closure phases, with the waste storages likely to be the most difficult features to resolve in the mine closure process. Contaminated water quality from tailings dams and waste rock dumps can require treatment "in perpetuity" at a cost of hundreds of millions of dollars. The problem is increasing with ever larger mine operations and waste generation volumes. This paper identifies leading practice methodologies in planning and operating mines and process plants to minimise the risks from tailings storages and how this might also affect waste rock management and even the design of mine excavations. These methodologies require a "big-picture" approach to develop an understanding of the overall issues and identify synergies between the different operational areas on a mine site that can reduce overall risk. With a conservative approach and realistic allowance for future costs it is possible to facilitate decisions at the mine planning stage that can reduce risk and save cost over the long term. This is in contrast to the common approach where each operational area is looking to minimise its own costs with a short-term view. Incorrect mine methodologies can be developed by allowing net present value (NPV) accounting methods to trivialise future closure issues.Methodologies discussed include: Integrated Waste Management - Significant structural improvements to tailings dams can be achieved if the structures can be incorporated into the waste rock dumps. Risk of AMD can also be reduced by utilising the tailings and waste rock effectively. This could go even further to consider the placement of wastes to limit mine void environmental issues; Process Optimisation - Water quality and the nature of potential tailings dam structures can be highly influenced by the geo-chemistry of the tailings. This can be modified by processing, where simple changes such as maintaining separate streams of geo-chemically different tailings rather than recombining them or by initiating further processing to remove problematic minerals such as sulphides; Enhancing Geophysical Properties - The geochemical performance of waste repositories can be greatly influenced by the geophysical properties of the stored materials, particularly the air-water characteristics, which are influenced by particle size, density and permeability. The geotechnical properties can be enhanced by strategic paddock dumping, blending and compaction.These methodologies are demonstrated by case histories.CITATION:Brett, D, 2013. Mine waste risk minimisation by integrated waste management and process optimisation, in Proceedings MetPlant 2013, pp 247-258 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By G. S. Hansford, C. J. N. Dempers, G. E. Searby, A. W. Breed, M. A. Jaffer

The bioleaching of sulfide minerals involves a ferric attack of the mineral with the role of the micro-organisms being the oxidation of the ferrous-iron back to the ferric form, and the oxidation of sulfur, either via thiosulfate or polysulfides, to sulfate. The kinetics of bacterial ferrous-iron oxidation and the chemical ferric leach kinetics of sulfide minerals can both be described as functions of the ferric/ferrous-iron ratio. The independently determined bacterial ferrous-iron oxidation and chemical ferric-iron leaching kinetics have been successfully used to predict continuous bioleaching operations.

Jan 1, 2000

The panic bars (and associated linkage's and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on Self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and soma commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in 'Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Qingsheng Liu

A new method of recycling aluminum dross for preparation Al-Si-Ti alloy was studied in this paper. This was carried out in two processes. first the aluminum doss was pretreated by leaching and calcining process, the fine purity and phase of the intermediate oxide powder up to electrolysis demands, then, could be obtained when aluminum dross after washing have been leached for 2h at 100? in 20% hydrochloric acid and calcined for 2h at 1200?, which was treated by cryoite-based molten salt electrolysis. Finally, the Al-Si-Ti alloy was successfully obtained through electrochemical co-deposition in the cathode shows a typical as-cast microstructure. This new recycling method can produce high quality alloy and may bring remarkable economic and social benefits.

Jan 1, 2010

By Edward P. Barrett

The production of sponge iron is one of the earliest arts in the metal¬lurgy of iron and steel. The idea of producing iron direct from ore at temperatures lower than the melting point of, the iron has persisted throughout the centuries. The purpose of this paper is to present a general picture of the methods, proposed or tried within the past 100 years, for producing sponge iron by treating hot ore with heated reducing gases. The abundant literature has been abstracted, and quoted freely. Publications concerning more detailed information on the various methods are referred to in the footnotes and in the bibliography.

Jan 1, 1949

The relationship between the maceral composition of coal and the strength of the coke produced from that coal has received a great deal of attention in recent years.Studies using two Bulli Seam coals, and blends of Bulli and Wongawilli Seam coals, from the IIIawarra Measures of the Southern Coalfield of New South Wales were carried out.The optimum range of vitrinite was found to lie between 45 per cent and 60 per cent (mineral matter free).Above and below this vitrinite range coke strength deteriorated. Coke strength indices increased with rank, and the optimum vitrinite content increased with an increase in rank. These changes require confirmation as trends by testing a third level of rank. It was noted that vitrinite content decreased with an increase in the specific gravity of separation of the coal.Use of petrographic analyses will increase confidence in choosing coals for coking, provided the coals are well known. Such analyses offer the possibility of greater flexibility in coal purchases and the possibility of producing a marketable blend from coals, which have limited market potential. Critical base coals for blends can be conserved.Significantly more work is required before coal reserves can be utilized to optimum advantage. This work would require extension of the studies discussed in this paper and, in particular, the testing of a wider range of rank.

Jan 1, 1971

One of the most common critical areas of longwall mining in terms of ground stability are the gateroad and bleeder entries. These critical entries provide much-needed safe access for miners and allow for adequate ventilation required for dilution of hazardous airborne contaminants and must remain open during mining of a multi-panel district. This paper focuses on the stability of the longwall entries subjected to a single abutment load such as bleeders, first tailgate, and last headgate. First tailgate and last headgate are also referred to as blind headgates and tailgates. A study of a longwall district through conditions mapping, support evaluations, and numerical modeling was conducted and evaluated by researchers from the National Institute for Occupational Safety and Health (NIOSH). The condition mapping and support evaluations were performed on entries that spanned the previous five years of mining and relied on a diverse selection of supports to maintain the functionality of the entry. Numerical modeling was also conducted to evaluate various support types with further investigation and comparison to the condition mapping. The study demonstrated the importance of the abutment load decay versus distance from the gob edge, the potential for a reduction in material handling related injuries, as well as optimal usage of secondary and standing support.

Jan 7, 2020

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

By J. R. Heberger

"The Safety Pays in Mining web application, developed by the National Institute for Occupational Safety and Health (NIOSH) Mining Program, helps mines determine the potential costs associated with mining injuries. This web app groups injuries by type, either by the cause of the injury or by the nature of the injury. When the user selects one of over 30 common types of mining injuries, the app provides information on the distribution of costs of workers’ compensation claims for that type of injury. Based on other user inputs, Safety Pays in Mining will estimate the total costs of the selected injuries, including an estimate of additional indirect costs, the estimated impact of total injury costs on mining company profits, and provide some examples of other items (services, equipment) on which companies could spend the savings that result from the prevention of injuries. This paper reviews the Safety Pays in Mining web application by discussing the development of the app, how it is used to show the true costs of mining injuries, and how mines can benefit from using this app. INTRODUCTION Injuries on the job cause pain and suffering. They can also profoundly affect profits and daily operations. In addition to paying direct costs or increased premiums for workers’ compensation insurance, a company might need to pay overtime for other workers to fill an injured worker’s job role, cover training costs for a replacement worker, or divert administrative resources in the wake of an injury. Safety Pays in Mining is a web app that estimates the distribution of these injury costs and assesses the impact that occupational injuries have on a company’s profits. The costs of specific types of occupational injuries in mining are not readily available as mining and insurance companies don’t usually share this information. As a consequence, companies only have cost information based on previous experience with their own employees. Therefore, if a mine never experienced a finger amputation for one of its miners, it would not be aware of the possible costs associated with this type of injury. In addition, injury costs are unique in that the cost distribution is so wide — with half of the injuries in our dataset having mean costs higher than 90th percentile costs — just using the average cost of a specific injury type does not provide adequate information. Some injuries involve immensely high costs, and even though the risk of these high-cost injuries occurring is low, mines need to be aware of their potential impact on their company’s financial health."

Jan 1, 2018

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By Lorrie Fava

Two needs in the mining industry, to enable overall process improvements, are open systems and network connectivity in underground mines. The Pando project, a collaboration between Symboticware, Vale and Xstrata Nickel, and supported by CEMI, addresses these issues, and leverages the solution platform to deliver intelligent applications. An open system is one that uses publicly available standards for its key interfaces. Vendor-neutrality and ease of information flow are two main benefits that result from the use of open systems. By facilitating the interoperability of systems, open systems allow information to be available when and where it is needed for decision support. Network connectivity in underground mines is typically limited, with hotspots in strategically chosen areas that are relatively static. Mobile equipment moving through a mining work cycle experiences intermittent connectivity; in this situation, seamless remote equipment monitoring is impossible. The Pando project establishes an open technology platform, adhering to the IREDES and OPC UA standards. It enables the collection and integration of information generated by mobile equipment? seamlessly while there is a network connection, and as a store-and-forward gateway to manage intermittent connectivity. The platform capabilities are leveraged to support embedded intelligent applications. This open platform, the SymBot, is a rugged hardware and software device. The platform complies with open standards for industrial automation and systems interoperability. The SymBot platform is capable of providing advanced real-time decision support at the device level, and is designed to be remotely configurable. Applications being developed through the Pando project include engine monitoring, a dynamic load weighing system, machine location monitoring and automated activity monitoring including production and maintenance reporting.

Oct 1, 2010

By Yongbin Yang

Cathodic reduction of oxygen is a process involved in many fields. As is well known, the mechanism of oxygen reduction usually varies considerably with electrode substrates. In this paper, cathodic reduction of oxygen on gold electrode was studied by linear sweep voltammetry with regards to cyanide leaching of gold. As the results shows, the electron transfer number increases as potential shifted negatively and decreases as pH value increases. Besides, the increment of electron transfer number as a function of potential decreases when pH value increases. When pH increases to 13.0, the volt-ampere curve exhibits a relative flat section with currents approximate to the limit current density of a 2e process. By varying dissolved oxygen concentration, the electron transfer number was calculated for pH11.0 at different potentials, the results being 2.387e, 2.732e, 2.982e, and 3.227e at, -0.35V, -0.40V, -0.45V, and 0.50V, respectively. The calculated current densities are in good conformity with measured results.

Jan 1, 2010

New Zealand China Clays produces a unique halloysite clay product at Matauri Bay, Northland.   The company has licences over four deposits that were derived from the weathering of rhyodacite domes. Clay is mined and processed from two of the four deposits and is refined using a complex process based on gravity separation.   The product is almost entirely exported to niche markets in 24 countries. The main market is the fine ceramic industry where the product is used as a component in the manufacture of high quality porcelain and bone china bodies. The use of halloysite in these bodies gives the manufacturer the ability to achieve high whiteness and translucency. The other major market is for use in technical ceramics, where the product is sought after due to its high purity, fine particle size and stability at high temperatures.

Jan 1, 1997

By K. M. Phamotse, A. S. Nhleko

"*Paper written on project work carried out in partial fulfilment of BSc (Mining Engineering) degreeSynopsisLiqhobong Mining Development Company (LMDC) has been experiencing problems with boulders after blasting where the fragment sizes exceed the maximum of 800 mm as per mine standard. As a result, the mine has employed various methods to improve the fragmentation. The goal is to produce a run-of-mine (ROM) feed that does not choke the crusher and cause delays in production. In order to achieve this goal, fragmentation distribution within the fines and coarse envelope must be optimized through effective planning of blasting activities and accurate execution.The mine determined the fines-coarse envelope within which the entire crushing system can handle fragments using Split Desktop software. It is expected that both the predicted and actual fragmentation curves lie within that envelope for optimal fragmentation. The Kuz-Ram model with blast design parameters of 2.6 m for burden, 2.8 m for spacing, and 127 mm hole diameter was used to predict the fragmentation. The results show that the blast design parameters may need altering to achieve optimum fragmentation. Furthermore, the execution of the drilling and blasting may be the cause of the fragmentation problems. The mean fragmentation size (X50) differs greatly, unlike the uniformity index (n)s values which are relatively close to each other (0.6 to 2.2). The mean squared error (MSE) values have a large range. A proposed solution is a modified burden, spacing, and hole diameter. It is concluded that blast design parameters need to be reviewed in order to obtain correct predictions. IntroductionFragmentation has an impact on the mine production cycle which comprises, inter alia, drilling, blasting, loading, hauling, and crushing. Correct fragmentation as set by the plant design is important as it reduces the time lost due to secondary blasting and/or loading difficulties. In this paper we analyse blast results at Liqhobong Mining Development Company (LMDC) in Lesotho for a period of six months. This project was undertaken to observe the trends from the blasts and to identify whether any discrepancies exist in the overall blast information. The period under study included 16 blasts."

Jul 1, 2019