Search Documents

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

By Linsheng Xu

When coal seam is under the integral thick sandstone (or conglomerate), the structure of thick sandstone is integral and its strength is rather high. After coal is extracted, the roof is hanging and caving is difficult. When the method of full caving is adopted in the longwall working face to control this kind of hard and difficult caving roof, the effect of roof-controlling affects directly the production and safety. In China Datong Coal Mines the extracting coal deposit is Datong Jurassic period. Most of the roof is sandstone and conglomerate. It is hard and difficult to cave. Having used special hydraulic power supports and other special ways to deal with the roof, the hard and difficult caving roof has been controlled.

Jan 1, 1986

By J. D. Cole

In order to reduce the number of longwall face moves and to increase the rate of gateroad construction, super longwall panels, 1000 feet wide and 12000 to 14000 feet long, are planned for Wolf Creek Collieries No. 4 mine. The development of the longwall panels at the mine has evolved from 5-entry, to 4-entry, to 3-entry systems. A three-entry system including pillar size and entry supporting method for the super longwall panels was designed for long-term stability. The design procedures included field observation and studies, laboratory properties tests, in-situ stress measurement, and computer analysis. Three pillar design methods consisting of PILLAR, ALPS, and the Wilson Method, and one entry supporting method, ROOFBOLT, were adopted in this study. The procedures, methods, and results are discussed in detail.

Jan 1, 1990

By Lance R. Barron

The U.S. Bureau of Mines, in cooperation with a central Utah coal .mine operator, began a study in July 1988 into longwall gateroad designs applicable to deep, bump- prone mine conditions. Prior to the study, four adjacent longwall panels, incorporating a variety of panel entry configurations using "yielding' chain pi liars, experienced severe bumps and coal outbursts at the face and in the tailgate pillars during panel extraction, resulting in several lost-time accidents and a fatality. To quantify those factors primari1y responsible for bump occurrences during panel retreat, a field investigation was initiated to confirm the anticipated performance of a two-entry gateroad system employing a large, nonyielding chain pillar design. Hydraulic borehole pressure cells and roof-to-floor closure [convergence) measurement stations were installed to monitor gateroad abutment loading and entry closure during panel extraction. Study results indicate that very high confinement of the coal seam by strong roof and floor members existing across the entire property, in conjunction with overburden depths in excess of 1.600 feet, provides for bump-scale energy storage in not only gate pillars, but along the entire periphery of the active mining area. Insufficient gate pillar designs were also identified as possibly enhancing the occurrence of bumps in the tailgate and adjacent face areas.

Jan 1, 1990

Virtually all mineable Appalachian coal seams exist in a multi-seam environment. This makes it inevitable that most seams will eventually experience interaction induced ground control and mining problems. Indeed, it has been estimated that every working face will experience interaction effects from previous or current workings at least once during its lifetime (1), and that these problems are considerably exaggerated when seams are in close proximity -- a distance of less than 110 feet. The continued increase in multi-seam problems has resulted in considerable research activities over many years (2,3,4,1). Theoretical analysis, numerical and physical model studies, statistical and empirical analysis of numerous interaction related field data have been applied to multi-seam mining situations and have identified many useful trends and design criteria (4,5,6,7). To fully utilize research results and transfer multi-seam mining technology to field engineers, a design model -- USEAM was constructed (8). This model, designed for close seam under-mining situations, was computerized to facilitate utilization. In the current research, a new computer program "MSEAM" was developed to produce a model for both under- and overmining close seam situations. It is hoped that both of these software packages will aid field engineers in using important interactive design criteria to gain a better understanding of interaction mechanisms. Through advance planning with these programs, detrimental interaction may be avoided and minimized, and occasionally a design can be selected which will allow interaction effects to be utilized to the benefit of mining operations.

Jan 1, 1987

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Karl H. Brandt

In the Auguste Victoria mine a bolted rectangular roadway has been kept open for the first time in the seam D/C after retreat. The target of the project was to gain a basis for planning and experience for future mining layouts in the same scam in view of the reuse of boated rectangular roadways. For this the roadway was additionally secured in sections with longbolts before the influence of the retreating panel had taken place. On retreat a concrete sidepack was concurrently put in place on the face side. The installed monitoring systems consisted of endoscopic devices, multiple extensometers (Tell-Tales), shear-tales, extensometers and convergence measurements. The experience that was gained was carried over into a physical and numerical model.

Jan 1, 2001

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998

By Christopher Mark

Mines with exceptionally low-strength roof (UCS <3,500 psi and CMRR <40) are much more likely to struggle with roof falls than other mines. Weak-roof is a particular problem for many room and pillar mines in the Midwestern and Northern Appalachian coal basins. Traditional roof support techniques are often not up to the challenge at these operations. This paper focuses on two mines, one operating in the Upper Freeport seam and the other in the Herrin No. 6 seam. Together, the two mines had more than 300 roof falls during a recent 5 year period. Each has experimented with a variety of roof bolt types and lengths, and with different supplemental supports. Detailed statistical analysis was conducted to determine which support combinations have proven to be most effective. Geology, horizontal stress, and time are also important at both mines. Successful control techniques have included; ? Identifying particularly troublesome lithologic roof units; ? Installing longer and stronger roof bolts; ? Installing supplemental support in intersections, and; ? Limiting the duration that a panel remains open. The lessons learned from these mines, and others like them, could help improve ground control safety for the entire U.S. mining industry.

Jan 1, 2004

By Clifford J. Roblee

In this paper, various seismic indicators are evaluated for ability to discern fractures induced into a rock mass by blasting. This is accomplished by presenting results from in situ crosshole seismic studies performed prior to and after a sequence of controlled blasts within limestone and dolomite rock near Austin, TX. Indicators investigated are compression (P-) and shear (S-) wave travel times, first peak and maximum amplitudes, first arrival rise rate, and the linear spectrum of the received signal. Compression wave travel time yielded the most consistent results, while the various amplitude indicators yielded the poorest results for the equipment configuration utilized. In addition, this study documents magnitudes of change in seismic measurements which occurred following blasting. Both P- and S-wave travel times exhibited a wide range of variation due to blasting. Near blast centers below the surficial fractured rock, velocity decreases of about 10% were noted, significantly less than the 50% decrease observed for previously fractured near-surface rock through which the explosive energy was vented. Signal amplitude measurements also varied in magnitude but were less consistent.

Jan 1, 1989

By Cosmo P. Fazio

Remote control roof bolting is approaching reality with the continued improvement of a number of components and subsystems being developed by The Bendix Corporation under sponsorship of the U.S. Bureau of Mines and the U.S. Department of Energy. The era of remote control research in roof bolting was initiated by the USBM in June of 1973 with the award of a contract to Bendix Corporation to design and build a roof bolt bender/inserter device. One year later in June of 1974, the Bureau awarded five parallel R&D contracts to develop a longer-than-seam-height flexible roof drill. The Bendix flexible drill design has been the most successful of the five, has been thoroughly tested in both laboratory and underground situations, and has been incorporated into a number of machine applications along with the roof bolt inserter. The purpose of this paper is to discuss the advantages of remote control bolting from both a safety and productivity standpoint. Applications of the flexible drill and roof bolt inserter on a number of government and industry supported programs are used to illustrate the advances being made toward the goal of remote control.

Jan 1, 1982

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By George Mishra

In mid-1979, J&L Steel Corporation experienced rapid failure of pillars after only two weeks&apos; operation with a combination of full retreat and partial mining in the 154 Road Section of its Nemacolin Mine, Greene County. The rate of advance of the "squeeze line" was very rapid for the first 500 feet, but it slowed down considerably as it approached some large coal blocks and gas well barrier pillars. After moving all section equipment out tc a safe distance, all accessible headings and crosscuts were filled with cribs and tri-set posts to prevent further spread of the squeeze. At one time, there was great apprehension by mine management that without implementation of some immediate corrective measures the safety of #3 airshaft and the only haulage and access road to the 8 Road mining area would be in jeopardy. In September, 1979, the U.S. Bureau of Mines established convergence monitoring stations outby the squeeze area. Readings were taken at weekly intervals until January, 1980, and monthly thereafter. Mathematical calculations, plot- ting of contour maps, and graphing of total convergence at different stations were used to follow and analyze the progress of the squeeze and provide guidelines for mining plans in the adjoining areas.

Jan 1, 1981

By E. Bane Kroeger

Rib failure is a hazard that has resulted in many injuries and fatalities in underground coal mines, especially in soft coal seams. Conventional rib control methods including rib boarding, shotcreting. steel meshing and geogridding, are fairly expensive and time consuming to install. Some methods, such as rib boarding, have met with marginal success at controlling rib failure. Under this research, the Rib Strap System (RSS) introduced by Dr. Chugh in 1999, was modified and new components were added. Both bench scale and full size prototypes were tested in the labs at SIUC to determine the best materials for fabrication and easier methods for assembly and installation. This laboratory research has developed new methods of securing the strap ends to smaller rib hoards, a new device to post-tension two straps together, and a technique for replacing straps without having to drill new rib bolts or for retrofitting straps to rib hoards that are already in place. The method used to secure the strap end to rib boards developed during bench-scale testing was dubbed the wrapped staple technique. It is very simple, requiring only 10-15 staples, with the end of a strap secured to a rib board in about 45 seconds. Several different prototype designs for a new device to join the strap ends together and tension the strap were fabricated and tested in the labs at SIUC. The device, dubbed the rib strap buckle, was very easy to install and held the straps firmly. One specific buckle design worked extremely well during testing and exceeded all expectations. The laboratory research also developed a method of replacing a damaged rib strap that can also be used to add rib straps to existing rib boards. The technique uses nails, spacer blocks, and band clamps to secure the new board and strap. This technique was developed to allow one person to replace a strap using only a hammer and screwdriver, negating the need to drill and install a new rib bolt using mine equipment such as a roof bolter or scoop. In addition to the technical feasibility, the cost of materials for the rib strap system was compared to the rib boarding method currently being used at a mine in the Illinois Basin. The mine is using 20 rib boards on each pillar at cost of about $223.60. The costs for the rib strap system depend on the materials chosen for fabrication but for the base case, were about $97 per pillar.

Jan 1, 2004

By Mao Bai

Mining in situations where there exists a potential hazard from inundation has always existed in coal mining, and often reserves were left unmined in favor of reserves with no such hazard. However, increased pressure on expanding the minable reserves and on producing low-sulfur coal, has made mining under water hazards necessary in many parts of the world. Recent joint efforts by the authors to develop case-history data bases of mining under water hazards has allowed the bringing together of Chinese and United States experience and guidelines for such mining. In China, mining under water hazards has been successfully accomplished for a number of years, allowing the development of a good data base from which to draw guidelines. In the United States, much more limited experience, and the longer delay in adopting longwall mining compared to the rest of the world, has forced reliance on a more limited data base and European experience. In the United States (and Canada), the data base is continuing to increase as more operations start-up. Developing a generally-applicable set of guidelines for international use, based upon extensive Chinese and other experience, appears feasible. The Chinese and United States experiences are detailed by case histories.

Jan 1, 1995

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Peter Hayes

Moonee Colliery operates a longwall extraction system in the Great Northern seam of the Newcastle Coal Measures, approximately 100km north of Sydney, NSW. In the initial mine area of longwall blocks1-4a, the Great Northern seam is overlain by a massive conglomerate approximately 35m in thickness. Unanticipated sudden, blocky caving of this material has produced windblasts with associated velocities of 100m/sec and over-pressures of 35kPa. Although these events have not resulted in fatality, the potential safety risk to face personnel was such that the mine was threatened with closure. The development of a Windblast Management Plan to minimise the exposure to windblasts, a Micro-seismic Management flan to predict caving events, and the use of hydraulic fracturing to generate caving on demand, have all contributed to the salvation of the mine. Prior to the introduction of hydraulic fracturing, falls were highly variable and ranged in goaf area from 2000m2 to 30,000m2 with an average of around 7.000m2. Hydraulic fracturing has introduced consistent and far less variable falls, planned as averaging around 5000m2 and all accompanied by microseismic warning, Moonee Colliery is believed to he the only operation in the world using real-time microseismic warning and using hydrofracturing as a day-to-day operational process. These processes have enabled it to return to financial viability in an environment of strict procedural control, whilst ongoing efforts are made to optimise and enhance these systems. Moonee&apos;s story is a case study of the successful application of research and development work to the economics of a mine.

Jan 1, 2000

By C. P. Mangelsdorf

The success of the Birmingham roof truss (Figure 1) in supporting some difficult roof conditions, particularly in the Illinois coal basin, has given impetus to the development of a number of alternate schemes. These schemes attempt to alleviate two major problems with the Birming-ham truss, namely, the time required for installation and the cost of material. Because of the difficulty of drilling angled holes and the number of different pieces of hardware which must be handled manually, most operators have been unable to install Birmingham trusses in the cycle and have had to schedule truss crews during the maintenance shift or whenever they would not impede production. Due to this delay the truss has traditionally been viewed as a supplemental form of roof support. In fact, the truss might qualify as primary support and replace at least two bolts if it could he installed in the cycle (and MSHA would accept it as an alternate in the roof plan.) [ ] Figure 1. The Birmingham truss. Two attempts to deal with the first difficulty have sought to streamline the truss hardware while preserving the essential character of the Birmingham truss. One of these, by Peabody Coal, is reported elsewhere in these proceedings by C. Bollier. Another is a contract issued by the Bureau of Mines to Bendix Corporation for the development of a machine, particularly suited for use in low coal, which will automate many of the operations currently executed manually. This machine is expected to be ready for field testing by fall of 1982. Once in place, a truss installed by either of these schemes will interact with the roof in the same way as a conventional Birmingham truss. An alternate approach has been proposed by several different manufacturers independently. Although the hardware details differ. the essential idea consists of two angle bolts, the heads of which are connected by a horizontal chord tightened to some pre-determined tension. Figure 2 shows the generalized concept and does not depict any one of the four systems proposed. The advantage of this scheme is that the angle bolts can be installed and tightened in the cycle, and as bolts, immediately satisfy the roof control plan. The horizontal chord can be added later to achieve almost any initial desired roof loading, the limits of which are defined below this scheme is referred to here as the angle-bolt truss. Because of a fundamental difference in the way in which load is transferred between chords, this design does not interact with the roof under subsequent loading in the same manner as a Birmingham truss. The purpose of this paper is to examine this fundamental difference and its consequences. [ ]

Jan 1, 1982