Search Documents

By K. Hodgson, Cook. N. G. W.

Most structures are designed so that the possibility of failure is eliminated. However, some degree of failure in the rock around deep mine excavations is inevitable if mining operations are continued. The presence of failed rock constitutes a hazard the magnitude of which can be predicted by computer models from calculations of the energy change per unit area mined in stopes, or the field stress around service excavations. Empirical relationships between these calculable quantities and the incidence of rock failures and delays associated with them have been established. Experiments on the computer using different layouts enable the mining engineer to select the least hazardous of otherwise acceptable alternatives, and to predict the incidence of damage ahead of actual mining, so that appropriate measures to maintain an adequate degree of safety and productivity can be planned in advance.

Jan 1, 2014

By R. Weideman, K. du Preez

Biological sulfate reduction has become a successful treatment alternative for acid mine drainage and Mintek is developing biological processes for treatment of highsulfate mine waters. Treatment of these high-sulfate waters is achieved by sulfatereducing bacteria that reduce sulfate to produce sulfide as a product, in the form of H2S and HS− at neutral pH. This introduces the opportunity to apply treated effluents from biological treatment processes for the recovery of metals, such as copper, from metallurgical waste streams. This study models the kinetics of copper sulfide precipitation from a complex bioleach liquor. The results indicated a rapid rate of reaction and the formation of covellite, suggesting the potential to use biogenic sulfide to recover copper as a metal sulfide product.

Jan 1, 2023

By S. G. Mgenge, J. D. Steenkamp

Tronox Namakwa Sands operates two ilmenite smelters for the production of high-titania slag and low-manganese pig iron. Slag or metal is tapped from one of two product-specific, bi-level tap-holes. In this paper the refractory design specific to the tap-hole refractory layout is described, as well as practices for slag and metal tapping and refractory maintenance. Further developments planned are briefly described.

Jan 1, 2014

By S. Banisi, S. M. Mousavi, S. D. Tafvizi, Gh. A. Parsapour, M. Mahmoudi

Generally, regrind circuits are used to increase the degree of liberation of value minerals which are fed to flotation circuits. At the regrind circuit of the Sarcheshmeh copper complex, four ball mills are in closed circuit with their hydrocyclone clusters. In the initial design of the plant, feed and underflow percent solids, and pressure drop of the hydrocyclones were 39% and 65%, and 15psi, respectively. Over the years, due to a reduction in the feed grade from 1.17% to 0.67% and changes in the operational conditions, the feed rate to each hydrocyclone cluster has decreased from 401 to 70t/h and consequently the pressure drop, feed and underflow percent solids have reduced to 4psi, 17% and 25%, respectively. The main objective of this research was to audit the feed solids concentration and pressure drop of the hydrocyclones and make the necessary modifications based on the Plitt’s model. The results of sampling showed that water recovery to underflow was 59% which was higher than normal values. By reducing the number of operating regrind mills from 4 to 2, the feed rate to each mill increased. After this modification and taking necessary measures in the plant to implement the new operating approach, the pressure drop, feed and underflow percent solids increased to 18psi, 28% and 58%, respectively. The water recovery of the hydrocyclones underflow decreased from 59% to 12%. These changes in addition to increasing the circuit efficiency saved 1000 kWh energy and decreased ball consumption by 925 ton/year because of reduction in the number of operating ball mills. Keywords: Regrind mills, flotation, audit, troubleshooting

Jan 1, 2020

By S. A. Hosseini, O. Asghari

"The quantification of mineral resources and evaluation of process performance in mining operations at Gole Gohar iron ore deposit requires a precise model of the spatial variability of three variables (Fe, P, and S) which must be determined. According to statistical analysis there are complex multivariate relationships between these variables such as stoichiometric constraints, nonlinearity, and heteroskedasticity. Due to the impact of these complexities in decision-making, they should be reproduced in geostatistical models. First of all, in order to maintain the compositional and stoichiometric constraints, additive log-ratio (alr) transformation has been applied. In the next step cosimulation, using stepwise conditional transformation (SCT) and sequential Gaussian simulation (SGS) has been used to simulate multivariate data. Through statistical and geostatistical validations it is shown that the algorithms were able to reproduce complex relationships between variables, both locally and globally. IntroductionThe key steps in mining projects are the quantification of mineral resources, definition of mining reserves, and production scheduling. They rely on the construction of a block model that is used to represent basically the spatial distribution of ore grades (Montoya et al., 2012). The determination of grades and tonnages affects risk assessment and economic evaluation of mining projects. Evaluation of process performance in mining operations requires geostatistical modelling of many related variables (Barnett and Deutsch, 2012). Iron ore quality is characterized by multiple variables: not only the iron grade but also the contaminants that interfere in the subsequent steel manufacturing processes. Consequently, the spatial variability of multiple variables must be determined. Key variables are frequently correlated, and such correlations must be honoured during estimation and simulation. Data from iron ore deposits constitutes compositional data; furthermore, relationships the between assay data are often heteroskedastic."

Jan 1, 2016

By B. Nemutudi, X. Zhang, B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, S. Pikinini

The comparison study on adsorption of potassium normal butyl xanthate (PNBX) and sodium (nbutyl) dithiocarbamate (SNBDTC) on sperrylite mineral forms a basis in understanding the floatability improvement and paves a way for the design of collectors that may impact on a wide range of arsenide minerals. This study used a computational density functional theory (DFT) and experimental microcalorimetry approach to determine the adsorption energies of PNBX and SNBDTC collectors onto a sperrylite mineral surface. From a computational aspect, we considered the most stable surface plane of (100) surface, which had been found to give the lowest surface energy, compared to the other surface planes. It was observed that the PNBX and SNBDTC preferred to bridge on the As and Pt atoms through the S atoms. These findings showed that the collector adsorbed on the surface through both Pt and As atoms and indicated that the As atoms were significantly active in the adsorptions. We found that the adsorption energies were in the order: SNBDTC (–278.38 kJ/mol) > PNBX (–270.92 kJ/mol), indicating that the dithiocarbamate had stronger exothermic adsorption than the xanthate. From the microcalorimetry test it was also found that the SNBDTC was more exothermic than the PNBX and the adsorption energies were: SNBDTC (–473.50 kJ/mol) > PNBX (–331.13 kJ/mol). These results showed that the nitrogen atom in the SNBDTC collector had a great influence on the adsorption strength of the collector on the mineral surface. This is due to the electron deposition behaviour of nitrogen atoms compared to the electron withdrawing character of oxygen and as such the SNBDTC showed better collecting ability than the PNBX. These results paved the way for the design of collectors for sperrylite and other arsenide minerals and suggested that nitrogen in a collector may significantly improve the ability of the collector for improved recovery. Keywords: Computational modelling, microcalorimetry, SNBDTC and PNBX collectors, adsorption energies

Jan 1, 2020

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

A Special General Meeting, followed by the February General Meeting of the Institute, was held in Kelvin House, Johannesburg, on 18th February, 1970, at 4.30 p.m. Mr J. K. E. Douglas (President) was in the Chair. There were also present 24 Members: Messrs A. R. C. Fowler, R. C. J. Goode, Prof D. D. Howat, Messrs D. G. Maxwell, J. A. Nixon, P. W. J. van Rensburg (Council Members), C. A. Border, J. C. Fritz, E. K. Gibson, P. L. Grimbeek, S. D. Hill, D. A. Immelman, P. J. Uoyd, M. Mrost, C. S. Macphail, D. G. Malan, W. D. Ortlepp, R. S. Pearson, A. J. H. Pole, Dr W. S. Rapson, L. W. P. van den Bosch, R. A. von Maltitz and Dr A. Whillier. Eight Associate Members: Dr M. I. Brittan, Messrs J. Brett, I. E. Clarke, C. L. de Jongh, W. B. Evans, D. Loubser, R. C. More O'Ferrall and G. R. Still. One Graduate: Mr T. J. Kotze. One Student: Mr J. A. Cruise. Nine Visitors: including Dr N. G. W. Cook, Messrs M. D. Labuschagne, A. Nicoll, S. Sadowski, Dr A. M. Starfield and Dr H. Wagner. Secretary: Mr D. C. Visser. Total present: 45. SPECIAL GENERAL MEETING The President: "You will have received notices of the Special General Meeting and I declare it duly constituted. In keeping with the trend of overseas and local institutes, your Council recommends that we should change our membership classification as indicated in the notes of the meeting. The new grades are proposed to replace those presently in the Constitution and By-Laws. In terms of Clause 4.8 of the Constitution a special general meeting must be held for the purpose of considering and, if approved, adopting with or without amendments, the revision of the undermentioned clauses of the Constitution, which Council now recommends should read as follows. Clause 2.2 'Corporate Members shall comprise the grades of Honorary Life Fellow, Fellow and Member', these being the equivalent of Honorary Life Member, Member and Associate Member. Clause 2.6. 'Non-Corporate Member shall comprise the grade of Honorary Fellow, Graduate, Associate and Student.' Are there any questions in regard to this proposal? If not would someone propose that these clauses be amended and adopted?" Proposer: Mr A. J. Nixon. Seconder: Prof D. D. Howat. The motion was then adopted. The President: "It is recommended that Clause 2.15 should read, 'A Corporate of the Member of the Institute shall be entitled to use the following authorised letters designating the grade of Membership in Honorary Life Fellow and Fellow, F.S.A.I.M.M. and Member, M.S.A.I.M.M.' Previously we used the letters M.S.A.Inst.M.M. and your Council considered that we should adopt the simpler lettering. Could I ask someone to propose that this amendment be adopted?" Proposer: Mr R. C. J. Goode.

By F. H. Touwen, N. C. Joughin

"Simulation is a technique for studying the operation of systems by synthetic experimentation. With digital computers it is possible to simulate even the complex production processes in gold mining. This has great potential in that it enables the investigation, analysis and comparison of mining systems to be done accurately, rapidly and at low cost. Two programs have been developed to simulate the principal underground production processes in gold mining.These are the simulation of any stope contract and the simulation of underground transport operations. The programs synthesize these mining activities from a large number of small unit operations. The stope contract program simulates rockbreaking by drilling and blasting and the cleaning of the panels by face and gully scraping. The transport program simulates the functions and movements of all vehicles running on rails on one underground level. The simulation programs provide an effective means for experimenting with mining activities."

Jan 1, 2014

By E. Bakhtavar, R. Mikaeil, D. Khademi

"Fuzzy-weighted integer goal programming has been developed and used to select the most suitable site to construct a central processing plant for several adjacent small-scale dimension stone quarries, based on the most effective criteria. In the first step of mathematical modelling, the most important goals and decision variables were defined. Accordingly, an objective function was used in the model for minimizing the sum of undesired fuzzy-weighted deviations. Fuzzy weights were determined by a matrix of pairwise comparisons of various expert judgments in this field and the fuzzy geometric mean. The goal and systemic constraints were also modelled. The most suitable site for the construction of the plant was selected after solving the mathematical model in the ExcelR Solver add-in. The selected site had various advantages over the other sites, such as the shortest average distance to the quarries, the shortest distance to power access and workforce, and the lowest land price. IntroductionSelection of the most suitable site of a plant is one of the most important considerations when constructing an industrial project. A suitable site has a significant effect on a company's competitiveness in the market. Selecting a desirable location for constructing plants such as mineral processing facilities is an essential part of the economic planning that will enable a company to meet the needs of related upstream and downstream operations. These units are considered to be best built near the relevant mining sites because of technical difficulties, the cost of transporting minerals, and the traffic hazard caused by the movement of trucks transporting materials. Two main types of research using multiattribute decision-making models have been reported for selection of a processing plant site (Safari et al. 2010, 2012). In that research, the analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal solution (TOPSIS) approach were applied to select the suitable locations for the mineral processing plants for phases 1 and 2 of Sangan iron ore mine."

Jan 1, 2017

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By T. Flitton, R. Peattie

"The extreme depths and consequent expense of drilling and sampling the gold-bearing reefs of the Witwatersrand Basin have resulted in limited data being available for estimation of grade ahead of the mining face. There is, however, a wealth of information from mined-out areas of these deposits. This estimation challenge resulted in the development of a unique method of Mineral Resource estimation.AngloGold Ashanti (AGA) utilizes a technique termed macro cokriging (MCK), which allows for the integration of the limited advanced borehole data with the large chip sample data-sets from the previously mined-out areas by adopting a Bayesian geostatistical approach. The MCK process, in short, is the estimation of mixed support size data together with the application of four-parameter distribution models.The gold value estimation for the Carbon Leader Reef (CLR) on the AGA TauTona Mine is used in this paper as a case study of the process and to demonstrate the effectiveness of this technique through production reconciliation. The current method has been proven over the last 20 years and is now an established part of the Mineral Resource evaluation process within AGA.IntroductionOwing to the extreme depths of the goldbearing reefs at the AngloGold Ashanti (AGA) Witwatersrand operations and the prohibitive expense and time involved in drilling boreholes to the required depth, only limited drilling and sampling data is available ahead of the mining face. Whereas traditional estimation techniques are interpolative, within the Witwatersrand the estimation is primarily extrapolative, with the majority of the data being sourced from the mined-out areas. This significant challenge to estimation resulted in the development of a unique method of Mineral Resource estimation and evaluation."

Jan 1, 2016

By P. Kitobo, T. Nduba, D. Mbay, J. B. Vangu, R. Ciband

The flotation plant tailings at Kamoa Copper Mine concentrator were found to contain a high proportion of extremely fine particles. The potential issues with settling these fine solids were resolved by the use of a poly-di-allyl-di-methyl ammonium chloride (DADMAC) coagulant, Flobead DB 45 VHM, in conjunction with a standard anionic polyacrylamide flocculant. This paper outlines some of the issues encountered and how they were resolved at the Kamoa concentrator. The potential to use this process and technology at other sites is also considered

Jan 1, 2023

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By D. F. Malan, J. C. Esterhuyse

"Mining in the Carletonville area of the Witwatersrand Basin predates 1934. Owing to the depletion of higher grade ore, the current activities focus increasingly on the extraction of lower grade secondary reefs as well as remnant extraction. Of particular interest is multi-reef remnant extraction. Numerical modelling was conducted to investigate some rock engineering aspects of remnants being understoped on a secondary reef horizon. An analysis of the stress evolution in the middling between two reef horizons indicated that a zone of high major and low minor principal stress develops between the two reefs. This indicates a high risk of violent shear failure. Some pillars were nevertheless successfully understoped in the past and a study was conducted to better understand this phenomenon. An ’extended’ energy release rate concept introduced by Napier and Malan (2014) proved to be useful for investigating this problem. It was found that bedding planes and lithology appears to play a role in the stable dissipation of energy in multi-reef remnant geometries. The study indicated that the stope convergence and the various energy components are affected by the presence, position, and properties of a bedding plane. The energy solutions are complex and sometimes counterintuitive. Care should be exercised when modelling specific cases. The modelling was nevertheless valuable as it indicated that energy dissipated on weak layers may reduce the risk of violent failure in a multi-reef mining scenario. Additional work is required to investigate if crushing on the reef plane plays a prominent role when mining these remnants. IntroductionTo extend the lives of the Witwatersrand gold mines, work is being conducted to include a larger number of remnants and pillars in the reserve base of the mines. According to Jager and Ryder (1999), a remnant is an unmined block of ground surrounded by extensive mining. Remnants are typically left because of adverse or difficult mining conditions caused by geological structures, poor ground conditions, low grade, or rockburst damage (Durrheim, 1997). In contrast, pillars are typically the result of rock engineering designs to control energy release rates (ERR) and seismicity. During the early 1900s, remnants formed by the practice of scattered mining layouts had a significant effect on seismicity. Numerous task teams were appointed during this period. As the industry expanded, the severity of rockbursting increased and the research was formalized after the 1960s. Various recommendations were made and many of these are still used as best practice today (e.g. Jager and Ryder, 1999)."

Dec 1, 2018

By C. van der Merwe, R. Lumbule, J. Kgomo

"The mining industry in the Democratic Republic of Congo has seen a significant expansion in copper and cobalt production in recent years. The greater proportion of this expansion has arisen through processing of oxide ores. The design of metallurgical processes for these oxide ores is based on the conventional equipment and layout for processing of sulphide ores, and comprises milling followed by leaching, solvent extraction, and electrowinning. The physical characteristics of the oxide ores, however, provide the process design engineer with an opportunity to examine critically the principles on which equipment selection is based and to design processes better suited to these ores. In 2015, ERG Africa began a project to expand the leaching capacity of the Luita hydrometallurgical facility. A number of innovative changes to the conventional process design were included in the modified flow sheet, which were validated when the project reached design throughput in November 2017. Of these changes, the most novel presented an alternative approach to mitigate the impact of colloidal silica on the operation of the solvent extraction plant. Introduction ERG Africa operates the Luita hydrometallurgical facility located at Kakanda in the Democratic Republic of Congo (DRC), treating malachite and heterogenite minerals to recover copper as electrowon cathode and cobalt as a hydroxide precipitate. The process was originally conceived as a heap leach operation followed by direct electrowinning of copper, with solvent extraction (SX) and electrowinning (EW) of cobalt. In preparing the sized ore for the heap leach operations, the undersized ore fraction at a P80 of 625 µm was discharged to a fines storage facility for later processing. This fraction carried with it approximately 30% of the copper contained in the run-of-mine (ROM) ore feed, and an equivalent proportion of cobalt.In a subsequent development, the cobalt SX section was converted to a copper SX facility, the leached cobalt being recovered from a bleed stream from the copper heap leach circuit. The operating cost for the process as then installed placed this facility well in the fourth quartile of the industry cost curve. The initial Luita operation was established in 2010 at a time when metal prices were above long-term averages (copper above US$3.00 per pound; cobalt above US$20.00 per pound), and the drop in prices in 2015/2016 presented a major challenge. The London Metal Exchange (LME) copper price dropped below US$2.00 per pound, with cobalt dropping below US$10.00 per pound in Q1 2016. This set in motion a range of improvement initiatives for the Luita operation. Central to this was the installation of a tank leach circuit to process the discarded fines and a modified SX circuit to manage colloidal silica. The revised Luita circuit reached design capacity in November 2017 and has proven to be well suited to processing of the oxide ore feed. This process design challenges the boundaries of conventional thinking in the areas of leaching, solid/liquid separation, solution management, impurity management, and metal recovery, and is the subject of this paper."

Nov 1, 2018

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

By F. Smit

Mining and plant disciplines can benefit from pre-concentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of pre-concentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2012

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

Recycling has become an important part of the lithium-ion battery (LIB) life cycle due to the growing demand for energy storage in applications like electric vehicles and renewable energy. Recycling spent LIBs provides a secondary source for strategically scarce metals, like lithium and cobalt, helping to reduce the environmental impact of LIBs. Organic acids have been proven to be effective lixiviants with the benefit of reduced environmental impacts, amongst which citric acid has shown to exhibit similar extraction performance when compared to mineral acids. Leaching LCO and NMC batteries with 1.5M citric acid and 2 vol.% H2O2 at 95°C, 20 g/L for 20 minutes achieved 93% Al, 90% Co, 96% Li, 94% Mn and 94% Ni dissolution. The strong chelating property of citric acid affects the separation of the metals, providing unique extraction opportunities. The first extraction uses 12 vol.% D2EHPA at a pH of 2.5 and O/A ratio of 2 to separate 96.4% Mn and 100% Al from the PLS in two counter-current stages. Stripping the loaded organic with 1.25M citric acid at an A/O ratio of 3 allows for up to 91% stripping of the manganese in a single stage. The second extraction then separates 96.5% Li from the PLS in three counter-current stages using 20 vol.% D2EHPA at a pH 5.5 and O/A ratio of 5. The raffinate remaining after the second separation contains 48.4 wt.% Co and 50.3 wt.% Ni. Keywords: Hydrometallurgy, lithium-ion batteries, metal recycling, citric acid, solvent extraction

Jan 1, 2020

By E. M. W. Skinner

Various models of near-surface kimberlite pipe emplacement have been proposed over the years. These include a top-down, phreatomagmatic model, a bottom-up, embryonic pipe model and three top-down explosive dyke models. AU of these models consider kimberlites as essentially the same rock type. However, different kimberlites have different pipe shapes and contain different rock types with very specific mineral assemblages and textures and therefore are likely to have been emplaced by different processes. Some authors have considered local geological differences as the principal reason for the contrasting geology but others argue that, while geological differences might contribute locally the petrographic peculiarities of particular kimberlites may be due mainly to inherent compositional differences specifically in the ratios of juvenile CO2 and H2O.

Jan 1, 2010