Search Documents

By N. Jovanovic, A. Vazirizadeh

"The main objective of this study is to find a solution to design a mass flow observer system with the minimum required sensors and maximum observability for a mineral processing plant. The second objective is designing a mass flow observer configuration with high reliability to manage sensor failures. This configuration will provide a robust monitoring system that increases plant availability and process measurement fault detection. Furthermore, the monitoring system is expected to improve process efficiency. In this investigation, the procedure of designing an observer system is presented along with three models to design the sensor network. The advantages and disadvantages of each models are discussed and finally the models result for an industrial case are presented and analyzed. INTRODUCTION The concepts of observability and redundancy of mass flow are directly linked with the ability to solve and estimate the mass flow. There are hundreds of streams in a process plant flowsheet, and for technical and economic reasons it is not possible to measure all mass flows. It is thus important to know for a set of measured streams, which of the unmeasured streams can be estimated. The concept of observability deals with this issue. It is also valuable to know whether a measured mass flow of streams can be estimated even if a sensor fails for some reason. Redundancy deals with this failure question. A stream is said to be observable if it can be estimated by using the measurements and/ or mass conservation equations. Also, a stream is redundant if it is observable even when its measurement is removed. Observability and redundancy analysis can be exploited for adding new measuring instruments. It can also play a useful role in efficient decomposition and data reconciliation problem (Narasimhan and Jordache 1999). The value of an observer system cannot be justified without considering its benefits. This justification is done through evaluation of data reconciliation, gross error detection and improving process performance such as outlined below:"

Jan 1, 2018

By N. V. Ramana Murthy

Utilisation of Low-Grade Iron Ore Fines after concentration not only helps in conservation of the mineral wealth, but also substantialsly improves the economics of iron ore mining. There has been need to develop suitable beneficiation process for upgradation of low-grade iron ores towards their rational utilisation. Presently the circuit adopted for processing iron ores has limitations in reduction of alumina. The depletion of high-grade reserves, utilisation of low-grade reserves coupled with in-creasing market pressure for improved product quality necessitates re-examination of the process flow sheets and evaluate alternative or supplemental processing routes. The main objective of the Process amenability studies for utilisation of Low-Grade Iron Ore Fines (-10mm) is to get Pellet grade concentrate with +65% Fe (min), SiO2 1.8% (max), Al2O3 1.8% (max) and other proportionate constituents by adopting suitable beneficiation techniques and to collect the relevant data (Quality and Quantity of the Products) for the process development. In an effort to formulate a conceptual process flow sheet, the Process amenability studies for utilisation of Low-Grade Iron Ore Fines (-10mm), which is lying at a mine site in India, samples were collected and taken up for the study. The efforts of R & D of NMDC are discussed in this paper. Low-Grade Iron Ore Fines (-10mm) sample assayed 60.10% Fe with 3.48% SiO2 Aland 4.48% 2O3from 40 microns to 300 microns. The sample consists of hematite as the chief ore mineral followed by minor amounts of maghemite. The gangue minerals include quartz and ferruginous clay in which quartz occurs as medium grained where as ferruginous clay occurs as fine to sub microscopic size mineral. The economical processing route evolved out of the studies finally could yield a final concentrate constituting 58.63% by weight along with Iron unit?s recovery of 63.51% assaying 65.10% Fe with 1.48% SiO2 and 1.85% Al2O3route that adopted comprises the following operations. Making slurry in a sump pump followed by grinding in close circuit with 48mesh size Screen. The -48 mesh size product was subjected o the Cycloning to remove slimes. The Cyclone Underflow product was subjected to Floatex Density Separation (FDS) to separate fine heavy minerals from the gangue minerals. The FDS Underflow was collected as concentrate. The FDS Overflow product was further subjected with Wet High Intensity Magnetic Separation (WHIMS) to recover more Iron units as magnetics. A conceptual process flow sheet was evolved, which may become the prelude to the subsequent finalisation of the process flow sheet for commercialisation.

Jan 1, 2014

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimisation.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By S. Owada

A national project of ?Establishing ?Green-Hydrogen (G-H)? Society in Honjo-Waseda Area? is now being developed by Waseda University together with four other universities and ten companies. The project involves three tasks of technological development of, (1)?G-H? production, (2)?G-H? refining, transportation and storage, and (3)?G-H? utilization. This paper focuses the first task of ?G-H? production from aluminium dross. We developed the physical treatment process by combining selective grinding with vibrating rod mill and electrostatic separation, in order to produce two kinds of materials, one is metal aluminium concentrate to recover it and the other is raw material to produce ?G-H? and aluminium hydroxide which can be generated by the treatment with sodium hydroxide aqueous solution. Here, we described the concentration mechanism of metal aluminium in the selective grinding and electrostatic separation and proposed a separation flowchart for optimizing the ?G-H? system in Honjo-Waseda area.

Jan 1, 2014

By M. M. Kulkarni1

Kaolin clay is used as a filler and pigment in various applications such as paper, paint, rubber, plastics, adhesives, ink and ceramics etc. Major mineral content in crude kaolin clay is kaolinite along with some accessory minerals as quartz, hematite, mica, feldspar, anatase, rutile, illemnite etc. The Fe and Ti bearing minerals play very important role in determining quality of the kaolin, as these minerals impart yellow, pink or darker color to the white kaolin. Conventional beneficiation methods used in kaolin processing are de-gritting, classification and sodium dithionite bleaching, which improves the optical properties of kaolin, wherein reduction of color imparting constituents such as Fe2O3 and TiO2 is marginal. In the present study, these coloring impurities are separated using selective adsorption of water-soluble polymers. Degritted kaolin samples after passing through 45 micron sieve is used in the study for selective flocculation by polyacrylamide based polymers. The effect of pH, zeta potential, and polymer dose on the reduction of impurities is studied. Analytical tools such as XRF, XRD, SEM, and TEM techniques are utilized and results are discussed in detail.

Sep 1, 2012

By R. Singh

The present paper deals with the development of flotation based process for enrichment of a lead-zinc sulphide ore from Ganesh-Himal region of Nepal. Detailed characterisation and flotation studies were carried out under varying process conditions. The sample assayed 2.47% Pb with 13.6% Zn. The ore was predominantly made up of spahlerite and pyrite in association with subordinate amounts of galena, minor amounts of pyrrhotite and chalcopyrite. Dolomite was the main gangue. The modal analysis showed the probability of fair liberation of sulphides from gangues around 210 microns but the locking of galena with sphalerite and other sulphides continued to finer sizes. Under the optimum process conditions the rougher lead and zinc recoveries were 96.3% and 90% respectively. Multistage cleanings of rougher products proved helpful in improving the concentrate grade, meeting the required specification. Based on the studies undertake a process flow-sheet for the concentration of the ore to individual lead and zinc concentrates was developed.

Jan 1, 2014

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By E. V. Manlapig, M. C. Harris

"The complexity of the flotation process has made the identification of an appropriate model structure, for use in the prediction of flotation circuit performance, far from obvious. Work performed under the auspices of the AMIRA P9 flotation program has indicated that the metallurgical performance achieved from a flotation cell arises from the interaction of two essentially independent property classes, namely the cell operating conditions and the properties of the cell feed stream. These observations have led to the development of a model structure that associates a constant set of flotation parameters to the streams of the circuit, which are transformed into a flotation response depending on the operating conditions within the flotation cell.A variety of alternative model structures exist within the literature which do not make this distinction between cell and stream flotation properties, and many of these models are in widespread use for flotation optimisation and design studies, both in industry and academia.In this paper, data collected from an industrial flotation circuit is used to derive the parameters associated with two different types of flotation models. Simulations performed using these models demonstrate the need to differentiate between cell and feed properties. A model that does not differentiate between these two properties fails to successfully predict the metallurgical performance of a flotation circuit after a disturbance."

Jan 1, 2003

By J. Masinja

The mining industry is known to be a potential major contributor to the industrial development of any economy. Large-scale mining has been going on in Zambia for the last 100 years. The impact of mining in Zambia has been to create a development corridor along the line of rail to the Copperbelt Province, where hitherto, mining was concentrated, and then to develop a large consolidated high-density economic zone covering an area of about 72 km by 60km. This area is home to a number of very large integrated copper/cobalt mining complexes. The mining zone has expanded to the Northwestern Province in the last 10 years, where the largest copper mine in Africa now exists, having produced about 300 000 tonnes of copper in 2011. The total output of the Zambian mining industry is now about 820 000 tonnes per annum with projections of reaching 1.5 million by 2015, due to new Greenfield investments expected to come online by then. These new mining industry developments have come on the back of strong and sustained high base metal prices, in the last 10 years or so, due to demand mainly from China and India. This new lease of life has increased the contribution of the sector to the national treasury. The mining industry in Zambia has undergone a very important ownership restructuring with the sale of the previously Government owned parastatal, Zambia Consolidated Copper Mines (ZCCM) which dominated the sector, to allow for private sector participation. The privatization process lasted from about 1995 to about 2002. The recent growth of the mining sector has unfortunately not been matched by an adequate supply of skilled manpower for various reasons. These include: (i) A lack of strong in-house training strategies by the new mine owners (ii) Decrease in industry support to the training institutions (iii) The demise of and restructuring of ZCCM which has consequently limited the Government human resources planning tools for the mining sector (iv) The cyclic nature for the fortunes of the sector has lead to fluctuating interest of student recruitment into training institutions (v) Limitations, both staff and equipment, in the training institutions (vi) A re-structuring of the training institutions This paper examines the current status, and student output from tertiary training institutions for the mining sector in Zambia. This is then compared to the skilled labour demands of the sector. The various cause and effect issues are considered and a proposal on how this skills gap could be addressed sustainably is proposed. Keywords: skills gap, graduate training, quality of graduates

Sep 1, 2012

By V. K. Gupta

Several approaches to the estimation of the size discrete breakage rate and distribution parameters (kj and bi,j ) of the batch grinding kinetic model are available in the literature. Analysis of a large amount of data available in the literature and our own data on several pure minerals and complex ores has shown that it is not always possible to obtain correct estimates of the two sets of parameters using known approaches as several widely different combinations of k and b parameters can sometimes simulate the batch grinding data reasonably accurately. It has been found that there are two main reasons: (i) all size classes are not well represented in the data and (ii) functional forms used for estimation of the two sets of parameters are sometimes chosen somewhat arbitrarily (especially in the case of complex ores), though they are actually uniquely related through size continuous breakage rate and distribution functions. A suitable experimental methodology has been described and demonstrated using some synthetic data and actual experimental data. A mill function approach, which does not require making any assumptions about the functional forms for k and b parameters, is also described and demonstrated. This approach is promising, but requires further development.

Sep 1, 2012

By N. R. Mandre

In the present work an attempt has been made to study beneficiation of low-grade iron ore associated with manganese clay by selective flocculation. The representative samples obtained for this purpose were initially subjected to chemical and mineralogical studies. The chemical analyses indicated 42.56 % Fe, 6.25% Mn, 8.72 % SiO2 and 13.60 % Al2O3 in the representative sample. The mineralogical analyses carried out under optical microscope showed that the ore mineral predominantly comprised of iron oxides and hydroxides along with manganese and silicate as gangue minerals. Prior to the beneficiation studies, the samples were subjected to settling tests. These tests were carried out by using poly acrylic acid (paa), poly acryl amide (pam) and guar gum (gg) as the flocculants. From these studies it was observed that settling rate of particles increases with increase in pH and a maximum settling rate of 0.23 cm/secwas obtained at pH 9 in presence of poly acryl amide. Further, the samples were subjected to selective flocculation studies using above-mentioned reagents. From these studies better results were obtained in the experiments carried out with poly acryl amide as the flocculant. Thus, it was possible to upgrade the iron content from 42.5 to 53%, with a recovery of 92%. However, 51% Fe with recovery of 87% and 50% Fe with recovery of 94 % was obtained using poly acrylic acid and guar gum respectively.

Sep 1, 2012

By A. A. Remes

High precision on-line particle size distribution measurement of mineral slurries has recently be-come available. It provides new tools for the development of monitoring and optimization methods for mineral grinding and separation circuits. The paper presents the development work at the Kemi chromite concentrator plant of Outokumpu Tornio Works in Northern Finland. The Kemi concentrator processes annually 1.2 Mt of chromium ore. The products are upgraded lumpy ore and metallurgical grade concentrate. The concentrate is produced using gravity separation methods, preceded by a rod mill - ball mill grinding stage. The separation process performance is strongly dependent on the particle size distribution of the grinding product at the Kemi plant. Particle size distribution has a significant effect on the concentrate grade and recovery. Currently a new laser diffraction based on-line particle size analyser is used for monitoring the grinding product. The analyser system allows the measurement of the whole cumulative particle size distribution simultaneously. It provides a wealth of new measurement information for process control. A monitoring and optimization scheme for grinding and gravity separation based on the particle size information is presented. The goal is to minimize the production of fine slime, and subsequently to improve the concentrate quality and minimize chromite recovery losses. Data-based recursively identified linear PLS process models are developed for optimization purposes. The preliminary results of the monitoring system operation in on-line use are presented.

Jan 1, 2014

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By S. M. Javad Koleini

Processing of phosphate ore sample was investigated for increasing phosphate content and reduction of its gangue minerals such as carbonates and silicates. Experimental designs were per-formed using Taguchi method. Different flotation methods were investigated for Moundon phosphate ore sample and three methods were used as follow: direct cellophane flotation, reverse calcite flotation and reverse quartz flotation. Because of the sensitivity of cellophane flotation to slime content, prior desliming was carried out before the experiments. Direct flotation experiments carried out and a concentrate contained 23.80% P2O5, 6.88% SiO2 and 72.33% recovery were produced. The achieved P2O5 content in the produced concentrate from reverse flotation of calcite was 26.44% and the recovery was 82.56%. The concentrate products obtained at optimum conditions by direct flotation of phosphate and indirect flotation of calcite were subjected to indirect flotation of calcite and direct flotation of appetite and final concentrates with P2O5 grade of the order of 24.19% and 26.96% were obtained, respectively. It was concluded that one stage direct flotation is unavoidable to achieve a product with low SiO2 content.

Jan 1, 2014

By J. Quinteros-Riquelme

Despite increasing demand, the supply of silver is limited by its inadequate recovery from ores. Due to its scarcity in nature, its high ore variability and complex mineralogy of current silver deposits, its recovery by mineral froth flotation presents a real challenge for process engineers. A silver ore often contains significant amounts of five to ten different silver minerals and knowledge of the mineralogy is a necessary precursor to flotation testing. In this work, a complex silver ore was treated by using batch laboratory flotation, in an effort to find the best experimental conditions to obtain the optimal silver recovery. Mineralogical characterization of feed samples was conducted using a combination of tools, namely the mineral liberation analyzer (MLA) and inductively-coupled plasma mass spectrometry (LA-ICP-MS), which indicated that most of the silver occurred as ?invisible? silver in pyrite. The pyrite assay of the ore was approximately 4%. The ore was processed in two flotation stages. The first stage, sulphide flotation, aimed to collect a sulphide mineral rich concentrate; then a non-sulphide flotation stage was performed by adding sodium sulphide and collectors to the remaining material in the cell, with the objective of obtaining a pyrite rich concentrate. To reach the target recovery of silver from this ore, various variables were altered. In the first stage: mixed collectors, activators, dispersants, and mainstream inert grinding were assessed. In the second stage, the conditions for sulphidization and subsequent flotation were both investigated. From the grade recovery curves for silver and sulphur it was possible to observe a similar metallurgical behavior for both elements, supporting the results given by the mineralogical characterization. Keywords: silver oxide, froth flotation, sulphidization, mig

Sep 1, 2012

By R. P. Bhagat

The paper reports results on sinterability of iron ores from the mines of Tata Steel Limited. The objective was to improve tumbler index (TI) of sinter and its reduction parameters, reduction degradation index (RDI) and reducibility (RI) while maintaining strand productivity same or to improve. Pot sintering experiments were carried out with Joda and Noamundi mines having LOI 3.8% and 2.9% respectively. Sinter basicity (CaO/SiO2) was varied in the 2.1 to 2.5 range and its MgO content was kept in the 1.4% to 1.8% range according to the blast furnace requirement. The ignition condition and vacuum was maintained according to the plant practice. The effect of variables namely, granulometric composition of ores vis-à-vis that of sinter mix, bed height, solid fuel, moisture content of green mix on the sintering indices was studied. The productivity with Noamundi ore (26 %+6.3 mm) was lower than that with Joda ore (45% +6.3 mm) at 4% coke in the mix and sinter basicity (CaO/SiO2) 2.1. However, with 4% coke (ash 22%) the RDI value was significantly high in case of Noamundi Ore, which decreased significantly to 29% with 5% coke. The size parameter of ore fines and its LOI content do influence the sintering speed and the sinter properties significantly. At 2.1 basicity ratio, the sinter with the Joda ore having coarsergranulometry had highest TI (=70.2%). The RDI (27%) in this case was inferior to that (23.2%) when Joda ores with finer size was sintered. Better RDI with finer sized ore could be attributed to better assimilation of CaO/ MgO with more balanced and uniformly distributed hematite minerals. The size parameter has been inter-influenced by the coke requirement. With the lower mean sized Joda ore the sinter RDI decreased significantly to 23% and the productivity improved to 42.9 T/(sq m*d) when the coke in the mix increased from 4% to 5%. An attempt to reduce the coke in the mix from 5% to 4% with respect to both the ores was not successful as it resulted higher RDI and lower strand productivity. The present study has revealed that sinter RDI improves (decreases) with decrease in the sintering time, while such correlation was absent between TI of sinter and speed of sintering. Corollary to this observation, one can take advantage of other stronger parameters to increase the sintering speed (and hence sinter productivity) without affecting the sinter strength. In the present study higher FeO sinters has displayed excellent RDI, however cold strength of sinter was not correlated with its FeO content. The TI and RI parameters of sinter improves marginally with increase in its MgO content while RDI got worsened. Keywords: LOI content, iron ore, reduction properties, sinter, noamundi, joda

Sep 1, 2012

By Arkady Senchenko, Sergey Rybkin, Svetlana Lagutina, Alexander Aksenov

"The application of autoclave leaching technology for sulfide concentrates containing base and precious metals is spreading nowadays. In the process of concentrate leaching silver accumulates in the forms of jarosite compounds, transforms into passive chemical state and is mostly found in solid phase. Effective technology development for silver recovery from solid phase of concentrate autoclave leaching raises the necessity for comprehensive research of silver forms of occurrence and their properties in this product. The possible form of silver presence in solid phase of concentrate from autoclave leaching is argentojarosite. This article is about the study of physical and chemical properties and structure of synthetic argentojarosite - AgFe3(SO4)2(OH)6. A method of argentojarosite synthesis has been developed under conditions simulating the process of autoclave leaching of sulfide concentrate, and includes silver dissolution in the form of Ag2SO4, Fe3+ sulfate hydrolysis, AgFe3(SO4)2(OH)6 build-up. X-ray data of synthesized argentojarosite completely correspond to those of natural mineral. The structural formula of this complex compound has been studied and confirmed. The chemical properties of synthetic argentojarosite, its solubility in acids and alkalis have been investigated. Phase changes when heating argentojarosite with the build-up of iron oxide and silver sulfate stop at the temperature equal to 650 ºC. Based on the results received the technological solutions for solid phase of autoclave leaching of concentrate have been developed with silver recovery of 95-98%."

Jan 1, 2014

By P. Han

The preparation technological conditions and regeneration method of two novel granulated adsorbing materials of rectorite/fly ash composite (Material 1) and rectorite/water quenched - slag composite (Material 2) and the use of them to remove heavy metals from copper smelting plant wastewater have been studied. The experimental results showed that under the preparation conditions with the ratio of rectorite to fly ash or water - quenched slag of 1:1, the amount of the additive (Industrial Starch, IS) of 15% (Material 1) or 10% (Material 2), the addition of 50% water, and the calcination temperature of 500? (Material 1) or 400? (Material 2), the efficiency of heavy metal removal with the granulated materials was the best, whereas the ratio of disintegration loss was the lowest. Under the treatment conditions of natural pH, and with the addition of the granulated materials of 0.07g/cm3 (Material 1) or 0.05g/cm3 (Material 2), a reaction time of 60 minutes (Material 1) or 40 minutes (Material 2), and the adsorption temperature of 25?, the efficiency for the granulated materials to remove Cu2+Pb2+Zn2+Cd2+ and Ni2+ from the copper smelting plant wastewater was 98.9, 97.5, 96.7, 90.2, and 79.1, (Material 1) or 98.2, 96.3, 78.6, 86.2, and 64.2, (Material 2), respectively, and the quality indexes of the wastewater after treatment conformed with the first level of integrated wastewater discharge standard (GB8978-1996). When the adsorption of heavy metal ions on the surface attained saturation the granulated materials could be regenerated by washing with 1 mol/L sodium chloride (NaCl) solution and still with quite good heavy metal removal efficiency. The granulated adsorbing materials had the advantages of high efficiency of wastewater treatment, easy method of solid-liquid separation and regeneration, and a broad prospect of applications.

Jan 1, 2014

By Pramila Misra, Jibardhan Meher, Debadutta Das

The concentrated coal-water slurry has been receiving considerable attention recently due its ability to replace fossil fuels. Attainment of stable and concentrated slurry has been succeeded so far through several physical and chemical techniques. The present article reports the formulation and stabilization of a highly concentrated coal-water slurry formed from five varieties of non-coking coals with variable ash contents obtained from Eastern part of India, employing three varieties of starch esters, such as starch benzoate, starch formate, and starch carbamate as dispersant. The apparent viscosity of the modified coal-water slurry has been measured by varying coal loading, dispersant percentage, pH, temperature, etc. The apparent viscosity of the slurry has been found to be decreased substantially on addition of 0.8% of adsorbate in the slurry. The particle-particle interaction has been considerably decreased and stable concentrated coal-water slurry containing high weight fraction of coal (61.5-63.5%) has been achieved in each case. The slurries stay in a non-settling form for about a month with viscosity in a permissible low range. The coal-water slurry has been found to behave as a non-Newtonian liquid. Comparison of the zeta potentials of the naked and modified coals evidences that adsorption of the dispersants at coal-water interface results in inhibition of the agglomeration of coal particles through mostly steric repulsions.

Jan 1, 2014

By M. N. Chandraprabha

Arsenopyrite is often associated with sulphides like pyrite, chalcopyrite and galena in refrac-tory gold ores. Selective flotation of arsenopyrite from associated sulphides is desirable for effective gold extraction when the gold is preferentially associated with the arsenopyrite matrix. By contrast, presence of arsenopyrite in flotation tailings poses a serious environmental threat due to arsenic dissolution. To prevent arsenic contamination from the mine wastes, it would be more economical and environmentally beneficial to remove this mineral during the froth flotation step. Use of Acidithiobacillus thiooxidans in the detoxification of arsenic containing sulphides is outlined in this pa-per. Biomodulation using Acidithiobacillus thiooxidans resulted in the preferential depression of pyrite from arsenopyrite. By suitable conditioning with cells and collector effective separation of arsenopyrite from pyrite was achieved. Biomodulation with wild cells did not yield separation of arsenopyrite from chalcopyrite. However, bacterial affinity could be induced to a desired sulfide mineral through environmentally controlled adaptation techniques. Through the use of arsenic-adapted bacterial cells, selective removal of arsenopyrite from chalcopyrite was readily achieved.

Jan 1, 2014