Search Documents

By D. G. Hulbert, J. H. Schubert, R. G. D. Henning

"Froth depth, along with reagent addition and aeration rate, is one of the crucial factors that can be used to control a flotation circuit. Sub-optimal setpoints and disruptions in levels have a severe adverse influence on grades and recoveries. A novel control strategy has been developed which provides exceptionally tight regulation of pulp levels. The controller observes and acts on all the flotation levels simultaneously. This provides a clear improvement over the standard approach, which is to use a set of Pl controllers. The system has been run on several industrial plants and has resulted in reduced fluctuations in level; fast responses to setpoint changes, and fast settling times after start-ups or disturbances. Testwork has shown that the improvements in level stabilisation translate into improvements in recovery and grades.IntroductionProcess control and optimization have an important influence on the economic efficiency of flotation plants. Inefficient operation can allow the wrong balance between grades and recoveries, and can also lead to adverse shifts in the grade-recovery relationship. Of all metallurgical operations, flotation loses the largest proportion of valuable material. Better operation can reduce these losses.An essential requirement of a good controller is that it should be able to stabilize and regulate the plant. Stable operation allows the performance of the plant to be observed without being obscured by the effects of disturbances and fluctuations. The optimum conditions can then be detected more easily. Good regulation can maintain operation at the optimum with proper neutralization of disturbances. Only when good stabilization and regulation are achieved can an optimizing strategy be properly applied.Froth depth, aeration rate and reagent addition are the three means by which a flotation plant is generally controlled. These control actions are effective on different time scales. Reagent addition is slower in its effect as some conditioning time is required. Since reagents are only added at the head of the circuit and at a few selected points within the banks, time is required for the effect of reagent changes to move through the circuit. Because of this slower time constant, reagent addition is more suited to process optimization and to dealing with slower changes in the process. An example of these slower changes is variation in the feed."

Jan 1, 1995

By L. Heber Cole

The search for potash in western Canada during the years of the great war led to the staking of claims on many of the "alkali lakes" and sloughs which occur in numerous localities in the morainic areas of the prairies, as well as in British Columbia, in the hope that potash salts would be found in commercial quantities. While the search for potash, up to the present time, has been disappointing, the prospecting of these areas has demonstrated that Canada possesses large reserves of sodium and magnesium compounds, principally in the form of sulphates, carbonates and chlorides. he writer first became interested in these deposits in 1911 while investigating the sodium chloride springs of northern Manitoba. In the fall of that year a number of the sulphate ? deposits in Saskatchewan and Alberta were visited, but owing to the excessive rains at that period, all the deposits were under water and only a few brine samples were obtained. Owing to pressure of other work investigations of the alkali deposits in western Canada, by the Mines Branch of the Department of Mines, could not be undertaken until the field season of 1921, but since that time the work has been continuous. During the summer of 1918 a reported discovery of a large deposit of potash bearing salts was featured in western papers and in a short time practically all the lakes and sloughs of the prairie provinces, which showed the least indication of being saline, were staked for potash. This reported discovery was not substantiated on investigation and many of those who had staked claims allowed them t~ lapse without the slightest effort to determine the character of the material in the deposits which they? had leased.

Jan 1, 1924

By D. J. Hallbom

This paper presents a novel methodology for the hydraulic design of mine backfill distribution systems. The ?operating range? method uses the concepts of the hydraulic grade line and equivalent pipe length to determine flows and pressures as the pipeline route and static head change over the life of the mine. The operating range method is easy to learn because it is semi-graphical and uses well-known design concepts (e.g., the hydraulic grade line) and slurry design models (e.g., the Durand deposition velocity model). However, by changing the paradigm in which these concepts are used, the operating method allows all potential pipeline cases to be analysed simultaneously without the need to know the exact pipe routing. It also allows the hydraulics engineer to quickly identify ?pinch points? and ?slack flow? zones, to estimate the effect of changing the size or length of any given section of pipe, to assess the impact of changing the material properties of the backfill slurry, to size the slurry pumps, and to size and locate rupture discs when required.

May 1, 2007

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

By A. D. Huffman

This paper covers the major salt deposits of Canada, with a brief summary of the early history of the industry and a more extended outline of progress since the second world war. Both dry mining and solution mining are covered, and the future of salt mining in Canada is discussed.

Jan 1, 1968

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By Brad Thrall, Howard Bradley, Michael Samuels

"LOCATIONViceroy Minerals Corporation owns and operates the Brewery Creek heap leach gold mine located approximately 55 kilometers northeast of Dawson City, Yukon Canada. Dawson was home of the Klondike Gold Rush 100 years ago. Upon startup in November 1996, the Brewery Creek Mine was the northernmost operating heap leach gold mine in North America and one of the most northern in the world. Located at 64"" 02' latitude, the mine is less than 300 km south of the Arctic Circle. Access to the mine is available at Kilometer 14 of the Dempster Highway, linking Inuvik, NWT and the Klondike Highway, 40 kilometers east of Dawson City. The immediate vicinity is the only part of Canada not glaciated in the Wisconsin advance, which has resulted in an oxide ore deposit due to approximately 80,000 years of weathering - an area unique in Canada.DESCRIPTION OF OPERATIONSIn order to utilize heap-leaching technology successhlly in an extreme northern climate, a number of design features were incorporated into the process flow sheet to operate on a year round uninterrupted basis. Winter temperature may dip below minus 50 ""C, demanding an approach to mining and leaching that is different from heap-leach operations in more temperate climates. Because of the severe winter temperatures, the mine operates approximately 2 10 days per year, while the leaching process is continuous on a year round basis. Run of mine ore (ROM) is placed on the heap beginning in mid April until late October. Overall gold recovery is projected to be 78% over a 325 day leaching cycle with annual production levels of 2.3 million tonnes of ore placed on the pad, with an average of 75,000 ounces of gold recovered per year. The recovery process utilizes conventional sodium cyanide leaching, carbon adsorption, high pressure stripping, thermal reactivation and acid washing, and on-site smelting.HISTORYFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996.A Socio-Economic Accord with the Tron Dek Hwech'in First Nations provides for employment, contract, and scholarship opportunities for First Nations citizens."

Jan 1, 1999

By Gordon Jackson

"There are two accomplishments of air and gas drilling: a new series of economic and mechanical challenges; and, acceptance as a standard drilling and completion tool.The new challenges are related to the concept of using a gaseous circulating medium in drilling for oil or gas. For purposes of discussion, a two part division has been made: the challenge of fluid invasion control and that of equipment and tools. Great strides have been made in the development of materials and techniques to combat formation fluid invasion. Chemicals and the ""mist drilling"" technique, now in use, have the versatility to cope with a wide range of downhole fluid entry conditions.Equipment and tools have been developed to meet the challenges of better, more economic drilling and completion possible with a gaseous circulating fluid. Economic and operational challenges remain.Acceptance of air and gas drilling as a normal operating tool was reached with difficulty. It is now established as a means of reducing costs in exploratory and develop-mental well drilling, exemplified in a recent study of 226 wells covering 419,407 feet of hole in the United States. Air reached the projected depth in 85 per cent of the operations, although formation water was encountered in 48.7 per cent of the holes. Slim hole bit performance and cost all compared for overall bit averages as part of analysis."

Jan 1, 1961

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929

By J. Nesset, F. Rosenblum, P. Spira

"Sulphide concentrates may exhibit self-heating to various degrees during storage or shipping, the worst cases presenting a serious hazard from fire and SO2 emission. Based on measurements of heating rates on a wide variety of concentrate samples in a special apparatus, combined with field experience, a methodology has been developed which allows concentrates to be rated for their heating potential. This has proven to be very useful in practice, for example, in deciding on the need to take preventive measures. Oxidation under ambient conditions in the presence of moisture initiates heating locally within a stockpile. In the case of highly active materials, such as those that contain abundant pyrrhotite, heating may progress through three stages to temperatures well above 5000C. However, most concentrates show little or no propensity to selfheat. Heating rates were used to estimate values of the heat output, or self-heating capacity (in joules per gram), which sustains the process at each stage. Thermal data from differential scanning calorimetry are also reported. Variables which affect self-heating are discussed and an actual case of heating control on a stockpile by covering is described. A simple apparatus which can be used to simulate stockpiling conditions has been tested successfully and is proposed as a convenient test system.INTRODUCTIONPrevious publications from this laboratory on the evaluation of self-heating in sulphides dealt with tailings backfill (Rosenblum et al. 1982) and waste rock (Rosenblum and Spira 1995). Sulphide concentrates may likewise exhibit self-heating in storage or during shipping. In a comprehensive but dated review, Kirshenbaum (1 968) pointed out the conflicting nature of information on means of controlling the problem, particularly with regard to the application of water and ventilation. Modelling by Simpson (1 97 1) of autogenous heating in stockpiled zinclead concentrate and associated field measurements by Wright et al. (1972) showed that the supply of oxygen by wind and the shape of the piles were the major factors in the development of hot spots. Simpson did not attempt to explain the complex mechanism of self-heating, simply ascribing its onset to oxidation. Pearse (1 980) investigated a potential method of testing for selfheating which consisted of (i) reaction with hydrogen peroxide and (ii) differential thermal anal sis, to characterize the response of concentrates at both ambient and temperatures above 100 C. He found the method sensitive enough to identify the need for careful handling but not to predict ignition. He recommended compacting concentrates and covering stockpiles with plastic sheeting to prevent ingress of air. All these workers recognized the key role played by oxygen and moisture in triggering self-heating."

Jan 1, 2001

By P. Hajiani

"Feasible and sustainable separation of lanthanides outside of China has been a dilemma for the past few years. The present technique uses REE electrophoretic mobility (Ui) variation in an electrical field to separate them. The present invention relates to a system and a method to separate and refine rare earth elements/compounds produced in hydrometallurgical processes while they are dissolved in an acidic medium, without any intermediate precipitation step. This process uses free-flow electrophoresis to isolate REE from the concentrate simultaneously without any pre-treatment or intermediate steps related to the nature of elements.INTRODUCTIONRare earth elements (REE) invariably occur together in nature, and any given mineral contains several or most of them. Production of high purity individual rare earth (RE) elements/compounds from their ores generally requires two stages of processing, including mineral processing and hydrometallurgy.Depending on the ore, mineral processing and hydrometallurgy treatment of the ore before REEs purification is relatively simple and quite achievable though conventional methods. However, producing individual REE from mixed REs compounds is tremendously tedious. RE processing often requires dozens of steps, each resulting in minute improvement in the complex RE streams. Separating and extracting a single REE requires a great deal of time, resources, and expertise. Today, advanced RE refinery facilities cost hundreds of millions of dollars to build. The high purity RE concentrates are separated into individual REE using solvent-based or ion exchange methods. Although there are several techniques to separate REEs, most of them suffer from different types of drawbacks. For instance, solvent extraction requires a great number of steps to achieve high purity REEs. The process which uses ion-exchanger for separation and refinery operates with low REE concentration in solution which leads to very large liquid volume quantity, bulky tanks, dehydrators, pumps, etc. The low concentration will adversely affect the water consumption as well as other chemicals. Similar chemical properties of those three valent elements do not allow them to be isolated easily one from one another using conventional separation techniques. Solvent extraction has been successfully applied for rare-earth refining (lanthanide, scandium and yttrium) for the past few decades in China. Since then, efforts have been dedicated to develop other techniques which could be applied industrially around the world."

Jan 1, 2016

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By H. Ewaschuk

"INTRODUCTIONRio Algom's involvement with the Enviro-Clear thickener began in May 1975, when tests on a laboratory waif were carried out by our Research and Development group. Commencing in June, further tests were carried out using a 3 foot diameter pilot unit. By December, a 30 foot full-scale thickener had been installed. In the near future, 3 more Enviro-Clear thickeners will be commissioned. With in the space of a year, almost $2.5 million had been committed to liquid/ solid separation facilities using the Enviro-Clear thickener. This paper briefly traces the extent and development of this commitment.BRIEF HISTORY OF QUIRKEQuirke Mine started operating in September 1956 at a rated capacity of 3,000 TOD. Because of market conditions, Quirke was shut down in December 1960. The facilities were re-opened at an increased capacity of 4,000 TPD in July 1968, by which time the demand for uranium had returned. Also, a second shaft was sunk, and by 1970, all of the ore treated in the concentrator was coming from the new Quirke II mine. The Quirke I stopes were allowed to fill with natural seepage. As well, acidic barren solution from the concentrator was pumped underground.With increasing demand for uranium, the capacity of Quirke will be further expanded to 7,000 TPD by 1978. Studies of how this expansion could best he carried out led to the consideration of a fairly new piece of equipment, the Enviro-Clear thickener, for certain operations in the concentrator. These operations are as follows:"

Jan 1, 1977

By D. S. Case

"Following a brief explanation of the land arrangements under the Alaska Native Claims Settlement Act, this paper will examine both a mineral exploration agreement and a mining development agreement negotiated between two large mining companies and two different Alaska Native institutions. One of the institutions is a village corporation involved with an exploration agreement and the other is one of the Alaska Native regional corporations, which is party to a mining and development agreement with Cominco Alaska for the development of the Red Dog lead and zinc mine.Special attention will be given to the factors to be considered when dealing with small aboriginal owners with few resources in the context of an exploration agreement, including development issues which must be considered early in the process. The paper will also discuss the unique royalty and taxation structures developed for the Red Dog Mine Agreement as well as environmental issues. The paper will also consider the ways in which the cultural and differing economic interests of an aboriginal owner and a large mining company have been accommodated in the both the exploration and development agreements"

Jan 1, 1998

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937

By L. Li

The rock quality designation (RQD) was initially introduced by Deere (1963) for civil engineering. But, its application has been largely extended to rock mechanics and has become a fundamental parameter in geotechnical engineering (e.g., Hoek & Brown 1980; Milne et al. 1998). The success of this definition is due, in great part, to its simplicity. However, this index includes a number of limitations. Among these limitations, a critical one is associated with the arbitrarily selected threshold value (e.g., Priest & Hudson 1976). Consequently, the RQD value would vary with different threshold length for the same core. Also, using the customarily and universally adopted but very arbitrarily selected threshold value of 10 cm (for NX cores) in the assessment of RQD, the RQD values usually tend to be either high or low in most rock engineering. Some intermediate values (50%) are less frequently encountered (Harrison 1999). The original definition of RQD does not well represent the actual quality of rock masses. In this paper, an improved definition of rock quality designation (RQDc) is given.

May 1, 2009

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By Neil Westoll

But First, An Overview of the Selwyn Basin and Its Resources ?World-renowned sedimentary-exhalative (SEDEX) deposits of zinc, lead, silver +/-barite ?Significant reserves/resources remain and vast tracts of prospective stratigraphyremain under-explored and untested. ?More details are at the Yukon Geological Survey?s Selwyn Basin Metallogenysite:http://www.geology.gov.yk.ca/metallogeny/selwyn/ Overview of Metal Price and Demand Trends ?The pace of economic change in China has been extremely rapid since the start of economic reforms just over 25 years ago. According to official statistics, economic growth has averaged 9.5% over the past two decades and seems likely to continue at that pace for some time. National income has been doubling every eight years. Such an increase in output represents one of the most sustained and rapid economic transformations seen in the world economy in the past 50 years.? Organization for Economic Co-operation and Development 16-Dec-2005

May 1, 2006