Search Documents

By Heath E, van Calsteren P, Turner S, McDermott F

U-Th isotope studies of recent volcanic rocks may be used to evaluate the depths and rates of melt generation beneath mid- ocean ridges and ocean islands. Island arc rocks exhibit a similar range in Th isotopes to that seen in both MORB and OIB, but while those with high (230Th/232Th) tend to have excess 238U, many of those with low (230Th/232Th) are in isotope equilibrium. The excess 238U is attributed to the preferential mobilisation of U in hydrous fluids from the subducted slab within the last 100,000 years, whereas the low Th isotope ratios in the higher-K arcs are primarily due to the introduction of subducted sediment. Preliminary results from mineral separates from lavas on Soufriere on the island of St. Vincent indicate that some of the minerals crystallised up to 50,000 years prior to eruption.

Jan 1, 1995

By Oda Y, Hashiuchi M

In the smelting section, flexible fuels such as coal or coke are used in place of heavy fuel oil in order to utilize energy sources more efficiently. Heat recovered from the off gas of the furnace has been converted by the waste heat boiler into steam, which is used for self power generation and for heating or maintaining various temperatures. The amount of the recovered steam in the smelter is currently increasing due to maximum utilization of powdered cokes. The heat source required to maintain the temperature of the electrolyte in the tank house is electric power and steam. However until recent year this steam was provided by its own heavy oil combustion type boiler in the tank house since the amount of steam consumed in heating the electrolyte is large. Though experimental work over the last few years has shown the advantages of reducing steam in the tank house by fully covering the cell, the implementation of the full cover can lead to other operating problems. However various improvements, mainly the covering of the cell with a simple device, have led to greatly reduced steam consumption. As a result, steam for the tank house is now provided by the waste heat boiler only bringing more efficient energy usage.

Jan 1, 1987

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By D Cohen, A Wurster

Many Southern African mining operations produce mine water which is beneficially and productively utilised on the mine sites and to support other water uses. Mine water treatment typically takes place within the context of integrated mine water management involving pollution prevention, waste minimisation, recycling and reuse as well as river discharges. Development of new and improved mine water treatment has focused on the neutralisation of metals removal, desalination of high sulfate waters and passive treatment. Mine water neutralisation processes now incorporate a combination of natural limestone and lime treatment, as well as features to maximise gypsum precipitation. The South African CSIR developed a suite of limestone-based neutralisation processes, which include reuse of CO2 and CaCO3 generated in the process. Desalination of high sulfate mine water is typically done using one of the following technologies:biological sulfate removal with different approaches to the handling of the sulfide generated in the process, and ultrafiltration (UF)/reverse osmosis (RO) treatment with different approaches to the handling and disposal of the brine. The current research and development focus is the separation and recovery of saleable products from the treatment residues and brine streams.

Jan 1, 2006

By Smith I. T

Mine operators have long recognised that the results achieved in primary blasting are critical to subsequent mining activities. With the introduction of "in the hole" drills under- ground and the advantages offered by the use of water gels in conjunction with ammonium nitrate-fuel oil (ANFO) explosives, new mining methods have been developed and enabled improvements in older methods. Pumpable water gels have been used with varying success underground. These gels allow a high loading density even in ragged bore- holes. The problems encountered with slumping in upholes is recognised so the current trend is to use these gels in downholes where wet holes are prevalent. Cartridged water gel technology has advanced to the point where it has allowed the replacement of nitroglycerin (NG) based explosives and pumpable water gels. Today, gels can be made as a tampable product for use in development headings or as a slump- ing product for downholes to give an effective coupling. With the introduction of the Tovex« pneumatic loaders, the problems associated with a pumpable gel were eliminated and gave the user the ability to alter his loading density.

Jan 1, 1977

The addition of a thallous salt to the cyanide leach of a calcined pyritic concentrate causes a marked increase in the"rate of extraction of gold. This probably is due to the activation of passive gold by.th,e. thallous ions'.''Lea'd, bismuth, and mercury salts, which should produce ' a, similai effect, fail to do so. It is postulated that'this latter result, together with'the reprecipitation of silver at low cyanide levels, is due to the presence of soluble sulphide. The use of thallous salts to reduce leaching time is discussed briefly.

Jan 1, 1964

By A Bonani, R Molina, H Constanzo

With conventional undercutting sequence the infrastructure on the production level often has a short serviceable life before major rehabilitation is necessary and is characterised by high maintenance costs. The abutment stress zone is the main cause of this situation. The application of the pre-undercut caving method variant can increase the availability and utilisation of the production level When a pre-undercut is used development and construction are carried out underneath a previously undercut area, far away from the abutment stress zone, under more favourable stress conditions. This paper describes the design principles and the relevant results from the application of the pre-undercut variant over three years to the Esmeralda sector of El Teniente mine. The aspects described are the undercut-extraction, the undercut-development and construction distances, the geometry and drawbells opening, cave extraction rates, and the rate and height of undercutting.

Jan 1, 2000

P.IISTRACTThe Pacific Rim is advantaged by the uniqueness and diversity of its geological features. Why then is geology given so little regard in the education systems of the countries of this region? Not that these countries differ greatly from those in other parts of the world. Papers presented during the Precollege Geoscience Education session at the 28th International Geological Congress (28th IGC) held in Washington, July, 1989, indicated strongly that the problem is universal. There is a marked decline in interest in the Earth sciences and many nations are looking towards methods that might change this trend. Problems affecting geological education include the lack of purpose and direction, its obsolete curricula and the difficulty in attracting gifted students.The world-wide plight of geology comes at the very time when it should be fundamental to a public understanding of the global effect of human population pressure. There is a universal awareness of "the environment" but very little awareness of the science that has supplied most of the data. Geology, as the science of the Earth, is of paramount importance to an understanding of our life on this planet, particularly in its role as the source of our every need.

Jan 1, 1990

By Pollard DM, Willis GM

The removal of bismuth from liquid copper in a vacuum furnace was studied over a range of pressures. The rate determining step changes from diffusion in the gas at pressures above 0.2 Torr to approach the Langmuir evaporation rate at pressures of 10-2 Torr. Oxygen and sulphur were found to have a negligible effect on the rate. Bismuth removal from copper sulphide was found to be considerably slower than from copper. This is consistent with the known thermodynamic properties of ternary sulphide melts.

Jan 1, 1980

White Cliffs Opal Field is situated in the Parish of Kirk, County of YulguIgra, New South Wales, about sixty miles from Wilcannia, and the River Darling. It is near the southern edge of the cretaceous basin of the interior of Queensland, New South Wales, and South Australia. Twelve miles south-west of the field, at Tarella station, a well sunk at the homestead reached silurian slates at about 127 feet, getting no water but about three miles north-west from the originally discovered and no central portion of the field, a well was sunk by the Momba, Pastoral cmpany, to a depth of 270 feet all the way through the cretaceous beds. At 250 feet a small supply of water was struck, but so much mineralised as to be quite useless. The temperature also was so high that a man could not keep his hand in it and Mr. Hogarth, the Momba Pastoral Company's manager, informs me that so corrosive was the action of the water, that a shovel left down the well for a fortnight, at the time of sinking, was completely eaten away.The well having now fallen in, I have been unable to obtain any of the water for analysis.The western termination of this portion of the cretaceous basin is situated about twenty miles from the present opal field, at which distance the slates, with (probably) devonian sandstones and quartzites resting unconformably thereon, commence to appear. The opal bearing country, as far as at present known, follows a more or less well defined line running north and south towards the northern end of the field, and north-east and south-west towards the southern extremity.

By Restarick C, Jowett A

A cylinder-cyclone system, fitted with a flow control valve between the cylinder and cyclone plus in some tests a variable cyclone spigot, has been used to achieve classifier separations at unusually coarse sizes relative to the diameter of the units used. The method has proved to be useful for low tonnage flows at low pulp density and variable feed rate. The system relies on use of a cylinder unit to reject excess water and fine particles, the amount rejected being adjusted by the flow control valve. The valve also adjusts flow rate and pulp density of feed to the cyclone unit, and can be adjusted to give a separation at a coarse particle size. The system has been used in connection with experiments on the pilot plant at Mount Isa, where a 76 mm system was used to classify feed to the lead secondary rougher circuit at sizes as coarse as 52 micrametres galena equivalent for split conditioning tests. Further tests have been carried out with quartz to assess the range of size separations Possible.

Jan 1, 1978

By Jackson GS

Since 1983 Cobar Mines Pty Ltd has madea concerted effort to improve the performance of its long hole open stopes, especially in the areas of dilution and fragmentation.This has resulted in modifications to stope design, drilling and blasting practice.

Jan 1, 1985

By Zharinov SE

Geonechanical modelling of island arc sys- tems and their analogs is investigated. Slow seismotectonic movements along the inclined deep fault zone under the compressive horizontal stress conditions are proposed to be the princi- pal mechanism controlling the structures and processes in the active continental margins. A model of shearing surface crack in an elastic half-plane is used for simulation. The main ele- ment of the model is viscous interaction bet- ween the crack sides, the viscosity varying with depth. To describe the stress-strain state of the medium an integro-differential singular equation is derived and solved numerically. The results of simulation are in good agreement with geological and geophysical data on the ac- tive continental margins.

Jan 1, 1987

The success of any industry depends on the planned integration of the policies and resources of the key components of the Australian economic and political structure - government, industry management, education, research, and the human resources of the industry. The Australian Mineral Industry, like Australia itself, has grown and developed at a rate not foreseen by many of our founding fathers and early industry leaders. Hence, now, as we approach the 21st Century, we need to re-think our approach to the significant new problems that are beginning to face both government and the Mineral Industry. Government initiatives, government information and support services, industry re-structuring, and research and development support, need to be carefully re-evaluated, re-diredted,. and strengthened, so that government, the community, and the Mineral Industry produce and receive the optimum education and research strategies and services. The support of academics and researchers, the development of facilities, and the design of new Courses for the future successful and beneficial exploitation of minerals need particular consideration.

Jan 1, 1986

By Wharton C. L

This paper describes a new computer program which can significantly increase the Net Present Value of either an open cut or underground mine by optimising the cut-offs used during the operating life of the mine. It was developed over a period of about three years by Whittle Programming Pty Ltd of Melbourne, Australia. Several authors have contributed to the theory behind this work, but the ideas were further developed, consolidated, and clearly explained by Lane (1988). It was this book that triggered the development of the new program. The paper starts with an explanation of the theory behind this type of optimisation, and then goes on to describe the computer methods used to optimise the different parts of the problem.

Jan 1, 1995

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2005

This paper outlines the thermodynamic and mass balance principles which affect the distribution of cobalt between matte and slag during the pyrometallurgical treatment of nickel - copper sulphides and considers the implications with regard to maximising the recovery of cobalt from the smelting and converting circuit.

Jan 1, 1992

By Tooley S. M

An experimental investigation of the hydraulic cuttability of coal from the Theiss Dampier Mitsui mine near Moura, Central Queen land illustrated the ability of established cutting equations to describe the behaviour of the coal during cutting. The experimental equipment developed for the work proved reliable. The results of the experimental programme are consistent with accumulated experience from overseas.

Jan 1, 1985

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986