Search Documents

By H. N. Treaftis, J. W. Cahn

THE previous determinations of the solvus of tin in solid lead disagree with one another by as much as 40°C or almost 10 at. pct. Even determinations that appear to be careful differ considerably in both the solubility and its temperature coefficient. Recent kinetic workl -3 on the rate of precipitation of tin from lead-tin alloys and thermodynamic work4 on the heat of solution of tin in lead have given some insight into the time necessary to reach equilibrium in this system. As this time is longer than that used in almost all previous determinations of the solvus, these determinations are questionable. Since the interpretation of recent kinetic results requires accurate values of the equilibrium solubility the present work was undertaken. DISCUSSION OF PREVIOUS RESULTS The methods used in previous studies may be placed into three classes: 1) Several alloys covering a range of compositions are allowed to reach "equilibrium" at a certain temperature.5-7 Some property, such as the X-ray lattice parameter of the lead-rich phase or the re- sistivity of the alloy, is then measured as a function of composition. The solubility limit for that temperature is taken to be that composition at which a discontinuity in the property occurs. However, the recent kinetic work has shown that tin precipitates in two stages. The first stage is rapid but leaves the lead still supersaturated. The second stage is very slow, and it seems from the equilibration times quoted by the investigators of the solvus that the end of the first stage of precipitation was usually mistaken for equilibrium. This is especially true at temperatures below 100°C where the first reaction is still quite rapid (from minutes to months), but where the second stage is so slow that very long holding times are required to reach equilibrium. Alternatively micrographic work8 on several alloys of different compositions seems to have given good results if done carefully. 2) The beginning of precipitation in a homogenized alloy is measured as it cools slowly8-10. Since reactions in solids undercool easily, such determinations will always give too low a temperature for the solvus. 3) Some property of an alloy is measured as a function of temperature while the alloy is above the solvus.5,9,11 The range of temperature can usually be extended slightly into the two phase region. Then the alloy is precipitated at a much lower temperature and slowly reheated. The solvus is taken to be the lowest temperature where the property of the reheated alloy is equal to that previously determined for the homogeneous alloy. Usually one also expects a discontinuity at the solvus in the temperature variation of the property for the reheated alloy. The difficulty in this method is the sluggishness of the dissolution process, and this method may give too high a solvus temperature. EXPERIMENTAL The phase boundary or solvus temperature was determined by a modification of method 3 for a series of chemically analyzed high-purity alloys, ranging from 5.1 to 26.4 at. pct Sn. The resistance, as a function of temperature, of a sample of homogenized alloy (which could easily be undercooled) was compared with the equilibrium resistance which that alloy sample attained after precipitation at room temperature followed by long isothermal anneals at various temperatures. Before each anneal the sample was rehomogenized and reprecipitated. The solvus temperature could be located to within 1°C as the intersection of the resistance vs temperature curves for the homogenized and equilibrium alloys. No attempt was made to locate the phase boundary more accurately since the limiting factor was the precision with which the alloys could be analyzed. This precision was ±0.1 wt pct Sn and corresponds to an error of 1 deg in temperature. This use of isothermal anneals differs from some of the previous investigations in which method 3 was used with baths of slowly rising temperatures. It was found early in the investigation that solvus temperatures tended to be high if the latter method was used even at extremely slow heating rates. For example a

Jan 1, 1961

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

Edward Dyer Peters, the only child of Henry Hunter Peters and Susan Barker Thaxter, was born in Dorchester, Mass., June 1, 1849. From his father he was a descendant of the Peters family of Ipswich and Andover, Mass., whose earliest ancestor settled in Essex County in 1659; while upon his mother's side he descended from several old Hingham families, as well as from the Quineys and from Governor Bradford. Between the ages of fourteen and sixteen he was a student at the Episcopal School for boys in Cheshire, Conn. Near the school was an old tin mine, and he used to spend his Saturday afternoons exploring it. When Edward was sixteen, his father sold his property in South-borough, and for the next three years lived in Europe. Sept. 26, 1865, Edward entered the Royal School of Mines at Freiberg, Saxony. In the summer of 1867 he joined his family on Lake Geneva, and spent a part of the season in that vicinity, going to Chamounix and taking other trips. Extract from a letter to his father: Elbingerode, Harz, Aug. 30, 1868: I left Freiberg with my friend Lilienthal, on Wednesday the 19th of August, reached Leipzig in the evening and spent the night in that city: the next morning we took the cars and in the afternoon reached Eisleben, in Prussia, which was to be our first stopping-place; there are immense copper-mines and smelting-works at this place, and the method of working the mines is very peculiar ... The next morning we got up at five and spent the whole day in the smelting-works where I obtained a number of drawings of the furnaces they use here and a good many valuable data. Saturday morning we got up at four o'clock, and descended a mine about three miles from the town; the Director of this mine was one of the most intelligent and agreeable men that I ever met; he accompanied us in the mine and explained everything that was new to us. The system of mining at Eisleben is peculiar to this town, and is not used at any other place in the world; the copper ore comes in narrow, flat veins eighteen inches high, at the utmost, consequently the men work lying flat on their left side and using the pick with both hands: the ore is carried out of the side passages into the main ones, in very low waggons about twelve inches high, and four by two feet; the boys who pull these waggons have a board buckled to their left thigh and their left arm; they pass their bare foot through a strap in the waggon and wriggle along on their side dragging the waggon after them, with their foot, almost as fast as a man can walk above ground. In the afternoon we walked over to Hittstadt, about twelve miles, and remained there Sunday and Monday. Monday night, at ten o'clock we went out to one of the smelting-works, to see the refining of the copper; this is only done at night, so we worked there from ten in the evening till eleven the next morning, and came home all blackened up and with blistered hands, for our skin was not quite so tough as that of the workmen: at noon the same day we took the stage to Ascherls-leben, and then the train to Stassfurt, where there are immense salt-mines, as well as factories for the manufacture of bromium, which latter process is, however, kept a profound secret, so we had very little hope of seeing anything but the salt mines; we were talking with our landlord about our disappointment, that evening, when he told us that the director of the Bromium works was sitting in the next room with no company but his glass of beer, so we went over to him, introduced ourselves as Americans, and actually succeeded in persuading him that it could do his business no earthly hurt if he showed us his works; at last he consented, after making us give our word of honor

Jan 1, 1919

By B. Yarar, J. Kaoma

[Introduction The critical surface tension of wetting of hydrophobic materials has been investigated extensively by Zisman et al. (1973) and relates the spreading of a liquid on a solid to the surface tension of this liquid. Thus, the Zisman ap¬proach shows that a plot of Cos 0 versus ?LV where, 0 is the contact angle and ?LV is the surface tension of that liquid in contact with its own vapor at equilibrium, produces a straight line which can be extrapolated to Cos 0 = 1. The intercept corresponds to a given ?LV, termed the critical surface tension of wetting. In instances, however, Cos 0 - ?LV plots show deviations from linearity. Alternative approaches have also included the plotting of adhesion tension (YLV COs 0) versus ?LV that can be interpreted in terms of critical surface tension data (Lucassen-Reynders, 1963). It has, on the other hand, been customary to correlate contact angle (0) with flotation data, although it is recognized that surface inhomogeneities and related contact angle hysteresis limit the interpretations pertaining to solid surface structures purely based on contact angle measurements. It is nonetheless true that 0 = 0, when the liquid is water, corresponds to a hydrophilic solid. Determination of ?c by contact angle measurements in conformity with the Zisman approach can encounter experimental difficulties, especially when solids are in a powder form. Following the reasoning that 0 = 0 corresponds to the hydrophilic state of a solid, froth flotation experiments can be expected to produce critical surface tension of wetting values for powders. The technique that consists of plotting recovery (% R) versus YLV data and extrapolating the linear part of the curve to % R = 0, has been described elsewhere (Yarar and Kaoma, 1984). This paper describes some of the results obtained by the extrapolation technique mentioned above, using various sulfide minerals. Experimental Materials Molybdenite (MoS2), sphalerite (ZnS), chalcopyrite (CuFeS2), chalcocite (Cu2S), and galena (PbS) were handsorted from massive samples and ground by mortar and pestle, and the -147 Fan fraction used in experiments; sulfur (S) was a C.P. Fisher Scientific Co. product. Method One gram powder samples were conditioned for three minutes in methanol-water solutions of predetermined surface tension values and the percents recovered by flotation using a Partridge-Smith Cell (Partridge and Smith, 1972), were plotted against each ?LV value. Results and Discussion The percent recovery versus ?LV for two naturally hydrophobic solids, i.e., natural molybdenite, MoS2 and sulfur are given in Fig. 1 where it is seen that ?c for sulfur is obtained as 31.5 mNm-1 whereas for MoS2, it is 26 mNm-1. Figure 1 also shows that the new flotation technique described, for estimating ?c is in good agreement with the Zisman method. Curves obtained by the same method for the minerals Cu2S, PbS, and ZnS are given in Fig. 2, where it is seen that for Cu2S, ZnS, and PbS, the extrapolation to % R = 0 produces ?c values of 36, 39, and 49 mNm-1, respectively. CuFeS2, on the other hand, gives a curve that does not permit such an extrapolation to obtain a ?c value with certainty. Nonetheless, treatment of the powder with 8.95 X 10-5 molar Na2S solution followed by washing with distilled water prior to flotation effects the curves as shown in the insert of Fig. 2. The type of curves given in Fig. 1 appear to be typical of hydrophobic solids as can also be observed in Fig. 3. The composition of solid and minute quantities of inclusions seem to play an important role as regards the surface properties of solids as reflected by the slope of the linear part of the % R - ?LV plot and thus the value of ?c obtained by this technique. For example, MoS2 of three different stoichiometric compositions produced the data given below. [MoS2MoS2.14Mo1.002S2 ?c mNm-126.029.031.0 dR/d?8.95.23.0]]

Jan 1, 1985

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

By A. H. Daane, B. J. Beaudry

The Sc-Y and Sc-Zr systems were studied by thermal and X-ray methods. Both systems are characterized by complete solid solubility in the low temperature hexagonal form and in the high temperature bcc form. In the Sc-Y system, there is a minimum in the solidus at 50 at. pct and 1365°C, while the solidus in the Sc-Zr system follows a nearly straight line relationship between the melting point of scandium and zirconium. There is a minimum in the temperature of transition from hexagonal to bcc in the Sc-Y system at 43 at. pct Y and 1175°C; while the temperature of transition is raised in the Sc-Zr system to a maximum of 1415 °C at 30 at. pct Zr. INTEREST in the metals of the first transition series has usually stemmed from their useful properties; however, there is now a great deal of interest in determining the fundamental nature of these metals. Since scandium is the first of these transition metals, a study of the preparation and Properties1 and the alloying behavior of scandium2 was initiated. In a continuing study of the alloying behavior of scandium, the systems of scandium with zirconium and yttrium have been established. Extensive solid solubility in both the Sc-Zr and Sc-Y systems was expected from application of the classical rules of Hume-Rothery. Also, the modified Darken and Gurry plot as suggested by Gschneid-ner3 showed ideal conditions for solubility in the Sc-Zr system with less favorable conditions in the Sc-Y system. The effect of scandium on the transformation temperature of zirconium and yttrium was of interest, since a recent empirical observation by Uly and Burr4 predicted that the solute scandium would raise the transformation temperature of zirconium and lower the yttrium transformation. In addition to noting the validity of the above predictions, the SC-Y and Sc-Zr systems were established. EXPERIMENTAL METHODS Materials. The metals employed in this investigation were crystal bar zirconium, distilled scandium prepared by the method described by Spedding, et al.1 and yttrium prepared by the method described by Carlson, et a1.5 The major impurities present in these metals are listed in Table I in ppm. Alloy Preparation. All the alloys examined were initially formed by comelting the two metals in a nonconsumable electrode arc-melting furnace under an atmosphere of purified helium or argon. The buttons were inverted at least five times and re-melted each time to ensure homogeneity. During preparation of Sc-Zr alloys, approximately 1 wt pct was lost which was attributed entirely to the loss of scandium by distillation. When preparing Sc-Y alloys, approximately 1.5 wt pct was lost, but it was assumed that the intended composition was maintained, since the relative weight lost when arc melting the component metals was nearly the same. Samples weighing 15 to 20 g were prepared for time-temperature thermal analysis, while only 1- to 2-g samples were prepared for the optical pyrometer and X-ray diffraction studies. Thermal Methods. The solidus and the melting points of the metals were determined by an optical pyrometer method described previously.2 The temperatures at which the transformation from hexagonal to bcc occurs were determined by differential thermal analysis. Several points on the solidus and liquidus in the Sc-Y system were also determined by this method and are in good agreement with those obtained by the optical pyrometer method. The procedure followed in the preparation of samples for thermal analysis and the furnace used have been described elsewhere.2'6 Since a limited quantity of scandium was available, most of the alloys were not melted during thermal analysis, thus avoiding contamination by the crucible. The alloy could then be reused and the composition changed by adding the desired quantity of solute to obtain the next alloy. Heat Treatment and X-Ray Methods. In order to ensure homogeneity, the "as arc-melted" alloys Were wrapped in tantalum foil, sealed in quartz capsules and heated at 1100°C for 15 hr and then cooled at a rate of 8 deg per min. Samples for X-ray diffraction were filed from these heat-treated alloys, sealed in 1/8 in. by 1/2 in. tantalum capsules under

Jan 1, 1963

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

By F. C. Bond, J. T. Wang

H. J. Kamack (E. I. du Pont de Nemours & Co., Inc., Wilmington, Del.)—Rittinger's law usually is stated to the following effect: "The work (or energy) consumed in particle size reduction is proportional to the new surface area produced." The law has been stated substantially in this way by Taggart20 Berry21 Dalla Valle22 Coghill and DeVaney,23 Richards and Locke," Gross,25 and many others, and, according to Gaudin,26 was originally expressed by Rittinger in the same form. Consequently there can be little doubt that this is the understanding of the law among most workers in the field of particle size reduction. Bond and Wang, however, express the law in the form "the useful work accomplished . . . ." (italics theirs). The distinction is critical, for in the form used by Bond and Wang the law becomes, as they themselves remark "merely a more or less arbitrary definition of useful work," while in its usual sense the law expresses a physical hypothesis which has been verified experimentally within certain limitations. Considering the way the law has been used, it might be stated more explicitly as follows: "In a given machine operating under a given set of constant operating conditions, the work consumed in the particle size reduction of a given material is proportional to the new surface area produced." Or, as Coghill and deVaney have said,27 "the (Rittinger) law holds only when the tests being compared are made under analogous conditions." There are occasions when the law transcends these limitations; for example, the surface area produced per unit energy consumption for a given material in a ball mill does not vary much over a fairly wide range of operating conditions. But by and large, the surface area production per unit energy consumption will vary with the operating conditions, the type of machine, and the material. The essence of Rittinger's law is that the surface area production per unit energy consumption is independent of the particle size, and this has been verified experimentally by numerous workers for numerous materials, within certain limits. An important limitation is that when one grinds to very small particle sizes, agglomerative forces may tend to interfere with size reduction so that the surface area increases less rapidly than Rittinger's law would predict. Within such limitations, Rittinger's law can be regarded as empirically established. The law has, however, certain theoretical implications, and it seems to be chiefly against these that Bond and Wang direct their criticism. Solids are believed to possess surface energy which is proportional to surface area. Thus, Rittinger's law implies a proportionality between surface energy produced and mechanical energy expended (for a particular material in a particular machine). It does not imply that all or most of the mechanical energy is transformed into surface energy; in fact it is known that most of the mechanical energy is transformed into heat. Bond and Wang assert that most of this heat arises from the damping of elastic vibrations of stressed particles. This may possibly be true for crushing (with which they are chiefly concerned), although in grinding it is probable that much of the heat arises from friction between particles. However, the fact that the surface energy is small compared to the heat energy does not invalidate Rittinger's law, which implies merely that they are proportional. The authors also criticize Rittinger's law on the grounds that "this theory cannot be justified mathematically, since work is the product of force times distance, and the distance factor is ignored," and "energy input must be the product of force times distance, and the Rittinger theory completely ignores large variations in the distance (strain dimension or deformation) throughout which a force must act to produce breakage of different materials." However, the quantities force and distance as such are irrelevant to Rittinger's law, which considers energy input as an integral quantity. The fact that different materials require different forces and strains (hence, different amounts of energy) to break them is incontrovertible but again is irrelevant to Rittinger's law, which, as mentioned before, applies -only to a single material. Even in theory, it would not be expected that the surface area produced per unit energy consumption would be the same for different materials, because the surface energy per unit area is presumably specific to each material. Bond and Wang advance another argument of a

Jan 1, 1952

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By M. Marciano, K. Kreider

Silicon carbide coated boron fiber (Borsic) reinforced aluminum composites were made which exhibit strength and modulus values predicted by the rule of mixtures. A successful technique for fabricating these composites consists of plasma spraying of monolayer filament reinforced tapes and subsequent diffusion bonding of these tapes into composites. The elastic properties of the composites were given by the rule of mixtures in reinforced directions. (The modulus parallel to the fibers was 32 x 106 psi for a composite with 50 pct by volume fibers. The other elastic properties for a composite with 50 pct fiber were transverse modulus = 14 to 16 X 10 psi, G = 9.5 x 106psi, and v,, = 0.23. Tensile strengths of over 190,000 psi were measured for the composites with 50 pct fiber and the average strength for these composites was 162,000 psi. These same composites had interlaminar shear strengths of 12 to 15,000 psi. Multidirectionally reinforced composites demonstrated the same reinforcement efficiency in strength and modulus as the uni-directimlly reinforced composites. Comrpessive strengths of composites with 50 pct by volume fiber were found to be greater than 250,000 psi. STRUCTURAL filamentary composite materials are being considered for use where high strength, high modulus, and lightweight materials are required. Metal matrix composites have been considered for use at temperatures ranging from cryogenic (aluminum stainless steel) to 6000°F (plasma sprayed tungsten plus tungsten fiber) and other requirements have been similarly diverse. Metal matrix composites offer high modulus and high strength in unreinforced directions, the ability to be joined by brazing or welding, and greater fracture toughness compared with the more easily fabricated resin matrix composites. This paper deals with the mechanical properties of aluminum boron composites, a system which is being considered for applications where lightweight, high modulus, and high strength are required at temperatures including those above the normal operating temperatures of resin composites. The boron fiber used in this investigation had an average room temperature strength of greater than 400,000 psi, a modulus of 58 x 106 psi, and a density of 0.09 lb per cu in. (2.6 g per cu cm).&apos; The fiber used in the composites had a coating of silicon carbide to retard degrading reactions with the matrix at elevated temperatures. The coated fiber, which is sold commercially as Borsic: has been reported to have excellent resistance to degradation at temperatures up to 600°C in air and in aluminum2 and the same mechanical properties as the standard bare boron fiber. Fabrication of Composites. The composites were diffusion bonded from plasma sprayed monolayer tapes. These tapes were fabricated on a substrate of aluminum alloy foil which is incorporated in the composite matrix. The technique consists of winding a layer of fiber on the foil, and plasma spraying the balance of the matrix alloy over the windings which bonds all of the components together. Advantages of this process include the ability to achieve good fiber spacing, Fig. 1, the formation of a good bond between fiber and matrix (achieved during the plasma spraying), and the adaptability of the process for forming large and complex parts. This is particularly true when used with brazing foil backing which alloys low pressure bonding of the structural shape. PROPERTY EVALUATION TECHNIQUES Tensile test specimens, 5 to 7 in. long with a reduced gage section and ,030 to ,040 in. thick, were cut from composite sheets with a diamond saw. The gage section was .200 in. wide, while the gripped section was .240 in. wide and over 2 in. long in each grip. The standard gage length used was 1 in., however, transverse specimens (i.e., specimens with the fibers oriented 90 deg to the loading axis) were tested without a reduced section. Twelve specimens were also made with a 3-in. gage length but no significant effect of gage length was measured. The tensile test specimens were mounted in a fixture and aligned in friction grips using a 10X microscope. Unbonded foil doublers (0.010-in.-thick aluminum) were used to insure firm gripping with a minimum of damage to the fibers. The test specimens were transferred to the testing machine in a rigid fixture and mounted in the self aligning loading train. Testing was performed using a Tinius Olsen four screw testing machine with a torsion bar LVDT load

Jan 1, 1970

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year&apos;s work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By K. L. Young

The general energy equation, including change in kinetic energy, was solved by numerical integration and used to evaluate simplifying assumptions and application practices over a wide range of conditions. When extreme conditions were encountered, sizable errors were caused by large integration intervals, application of Simpson&apos;s rule and neglecting change in kinetic energy. A maximum error of only 1.31 percent was caused by assuming temperature and compressibility constants at their average value. It was discovered that a discontinuity can develop in the integral for the injection case. This discontinuity indicates a point of zero pressure change and is an inflection point in the pressure traverse. INTRODUCTION When a pressure in a gas well is to be calculated, one of the first decisions is to select a method of calculation. In many instances, this selection becomes a problem because the literature, at best, provides an evaluation of any method for only a limited range of conditions. Once a method has been selected, a question often arises as to the size of the calculation interval which should be used. The question regarding calculation interval arises because an analytic solution is not obtainable and approximate solutions must be used. This paper presents an evaluation of major assumptions and application practices of probably the two most widely used methods for calculating steady-state single-phase gas well pressures. The two methods are Cullender and Smith1-" (numerical integration), and average temperature and com-pressibility. The Cullender-Smith method assumes that change in kinetic energy is negligible and is normally applied in two steps with a Simpson&apos;s rule correcton. The average temperature and compressibility method, in addition to neglecting kinetic energy change, asumes that temperature and compressibility are constant at their average values. This method is normally applied for wellhead shut-in pressures of less than 2,000 psi, and in one step. Computer programs were written to compute bottom-hole pressure with and without the assumptions, using various approaches. Values of input parameters investigated are shown in Table 1. Flow rate was limited to a maximum of 5,000 and 10,000 Mcf/D for tubing sizes of 1.610 and 1.995 in. ID, respectively. Flow rate was also limited to 10,000 Mcf/D for a tubing size of 2.441 in. ID when wellhead flowing pressure was 100 psia. These limitations were imposed on flow rate so as not to exceed sonic velocity. The z factor routine available necessitated limiting bottom-hole temperature to 240F and wellhead pressure to 3,000 psia. Pressures were compared on the basis of percent deviation from the trapezoidal integration of Eq. l or 2 at 100-ft intervals. A preliminary investigation indicated that a 1,000-ft interval solution would differ from a 50-ft interval solution by less than 0.25 percent; therefore, the 100-ft interval was chosen for a base. For the purpose of comparison, deviations less than 1 percent were considered insignificant. where 111.1 qeC2/d p = kinetic energy term. Eqs. 1 and 2 can be evaluated numerically at specific depths using the trapezoidal rule as shown by Cullender and Smith. If change in kinetic energy is neglected and temperature and compressibility are assumed constant at their average values, Eq. 1 can be integrated to give the average temperature and compressibility equation,

By G. F. Fix

Oil and gas activity reached a higher peak in Indiana during 1940 than for any like period during the past decade. Major activity, as during 1939, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin, where most of the increase was due to field drilling in previously proven areas. The amount of wildcat drilling was about the same as for 1939. No new fields of any apparent consequence were discovered during the year, with the possible exception of the College pool, in southwest Posey County. Only one well had been completed in this area at the end of the year. About 10 ft. of saturated Aux Vases sandstone was drilled in this well and the initial production was I00 bbl. of oil a day. Other discoveries during the year 1940 include: St. Thomas, in southwestern Knox County, where four McClosky wells, ranging from I00 to 300 bbl. a day initially, were com-pleted; Buff kin, in central Posey County, with 11 oil wells and 5 gas wells completed; and new developments in two old areas —Randolph County (part of the old Trenton field) and Gentryville, northwestern Spencer County, where some oil was found many years ago. The St. Thomas field proved disappoint-ing, with very spotty production from the McClosky horizon of the St. Genevieve limestone at a depth of about 1875 ft. The discovery well flowed 362 bbl. a day ini-tially. At the end of the year the field was pretty well outlined by dry holes and some inside locations were dry. The Buffkin pool also proved spotty, with production from shallow Pennsylvanian sands and from the Basal Pennsylvanian Mansfield sandstone, the latter at a depth of approximately I175 ft., with small production from the Cypress sandstone of Chester age. Oil wells in this pool are small, ranging from 25 to 75 bbl. a day. The Randolph County area, on the east side of the Trenton gas field, showed some promise for a commercial gas field, with four completed gas wells having cumulative initial flows of about 1,200,ooo cu. ft. a day. The area appar-ently was not depleted during the Trenton boom at the turn of the century, since casing pressures are about as high as the virgin pressure in the old field. Elsewhere the pressure has dropped as low as 5 pounds. The Griffin field received most of the drilling during 1940, with 163 completed oil wells. This field now covers about 3200 acres on the Indiana side of the Wabash River and is not as yet completely delimited. It produced the major part of Indiana&apos;s oil during the year—a total of 3,594,000 bbl. At the end of 1940, there were 253 producing wells in Griffin. New Harmony had five completions for a total of 24. The Rockport field, in Spencer County, continued to be actively developed and had a total of 45 gas wells and 9 oil wells at the end of the year. Oil in commercial quantities had not been found in the field previous to 1940. Total gas production for the year was 394,470,000 cubic feet. In all, 521 wells were drilled in the state during 1940, as compared to 377 for 1939. Of this number 248 were oil wells, 77 were gas wells and 196 were dry. Divided into

Jan 1, 1941

By J. F. Smith

ELASTIC constants of yttrium and eleven of the rare earth elements have been measured. This has been accomplished by measuring the propagation velocities of ultrasonic pulses. The velocity measurements were made by noting the elapsed time between an applied pulse and the appearance of successive echoes. The pulse-echo technique has become relatively common, and the basis of the measurement is outlined in several standard tests, e.g., Heuter and Bolt.1 Two important assumptions are made when using this method for the determination of elastic moduli. First, the pulse is assumed to propagate as a plane wave. To justify this assumption, the cross section of the test specimen should be large compared to the wave length of the transmitted pulse. For these measurements on the rare earth elements the minimum cross section wave length ratio was about 20. A second assumption which must be made when using polycrystalline specimens is that the grains are sufficiently numerous and randomly oriented so that the specimen may be approximated as elasti-cally isotopic. The grain size in the as-cast specimens which were used is believed to be sufficiently fine for this approximation, and the degree of preferred orientation is believed to be small. Supporting this viewpoint is the fact that elasticity measurements by the pulse-echo technique on as-cast specimens of other metals give results which are in satisfactory agreement with values obtained by other techniques. Hence, it is believed that the measured elasticity values for the rare earth elements are not apt to be seriously in error due to the assumption of elastic isotopy. The apparatus used in this determination was a modified Sperry Reflectoscope with a precisely calibrated time base circuit. Piezoelectric transducers were used both to generate the pulse and to detect the echoes. X-cut quartz crystals were used for the longitudinal modes, and Y-cut quartz crystals were used for the shear modes. Frequencies of 2.25 and 5 megacycles per sec were employed. Most of the specimens were 2.5 to 5.0 cm in length. Results Table I is a tabulation of the measured propagation velocities of longitudinal waves and of shear waves, together with densities obtained by Sped- ding, Daane, and Herrmann2 from lattice parameter measurements. The shear modulus, Poisson&apos;s ratio, and Young&apos;s modulus were calculated from the data in Table I through use of the following relationships: µ = pv32 [1] s=2-(vb/vs)2/2[1-(vb/vs)2] [2] and Y= 2µ(l+s) [3] where s is the shear modulus, Y is the Young&apos;s modulus, s is Poisson&apos;s ratio, p is the density, V0 is the longitudinal wave velocity, and v, is the shear wave velocity. The calculated quantities are shown in Table 11. Compressibility values can be computed from the relationship and the computed values may be compared with measured values obtained by Bridgman.8 Table III lists the data for such a comparison. The agreement is satisfactory, being particularly good for neodymi- um and gadolinium, poor for samarium, and intermediate for the other elements. Some variation is expected since Bridgman&apos;s measurements are isothermal, whereas the present measurements are adiabatic. In addition there may be some effect due to small variations in purity. Though most of the rare earth metals measured by Bridgman and all of the metals used in the present measurements were prepared at this laboratory, minor purity variations might exist since the samples came from different lots. Also, any imperfections such as dislocations, vacancies, voids, grain boundaries, microcracks, etc., should contribute to the volume change of a com-

Jan 1, 1958

By R. J. Hopkins, L. B. Haney

On the basis of limited experimental work conducted at the Port Pirie smelter, it would appear that, by increasing the specific surface of sinter, and possibly that of coke as well, a marked increase in the rate and degree of sinter reduction in the furnace shaft can be achieved. Fusion-point tests have shown that this increased reduction means a much higher sinter fusion point and narrower plastic zone, while the more efficient utilization of coke in the furnace is inherent in the intensification of reduction by the provision of a more reactive sinter surface. Investigations aimed at increasing the ability to operate the blast furnace with a higher lead tenor of sinter reducing fuel cost proportionately, and at eliminating the loss in reduction potential in coke entering the furnace, as shown by the presence of appreciable proportions of CO in the top gases, are reported. Several lines for future investigations that could result in improved smelting methods are proposed. A SOMEWHAT informal presentation of ideas on lead blast-furnace smelting will be given in this paper. These ideas have been developed during observations of furnace behavior at Port Pirie and earlier at Mt. Isa, and have been guided by the results of laboratory experiments at Port Pirie. The authors do not intend to propound any particularly new theories, but present their ideas as a basis for discussion which may help toward a better understanding and improved control of blast-furnace operation. Performance variations of considerable magnitude occur from time to time at most lead blast-furnace plants. While Port Pirie is fortunate in having a very regular supply of high grade concentrates, it is no exception in this respect. Such irregularities are of considerable economic importance and they constitute a challenge to present-day metallurgists in their efforts to obtain an ever greater degree of control over furnace operation. In operating as Port Pirie does with a relatively high lead charge, it has been recognized for a long time that shaft conditions are ,of the greatest importance. A practical, or engineering, attack on the problem of accretions consisted of changes in furnace design, e.g., by widening the shaft to 10 ft above the bottom row of tuyeres, and by the provision of curved ends and vertical walls.&apos; That this attack has had a great measure of success is shown by the fact that barring down of these wide furnaces is rarely necessary, shaft conditions have greatly improved, and sensitivity to charge variations has been markedly reduced. These modifications, followed by some metallurgical changes (chiefly the incorporation of pig iron into the furnace charge in 1948), have brought furnace operation to a point where some variables which were previously masked can now be studied. Accordingly, over different periods of time during the last five years, such variables as could be given numerical values have been recorded and subjected to statistical examination. The objectives of this work were: 1—to reveal the true importance of the different variables and 2—to show the proportion of total furnace variation which is unexplained and therefore referable to causes not measured at present? e.g., shaft accretions, sinter structure, coke structure, and others. Statistical Study of Variables In this work factors relating to furnace speed and lead reduction have been examined: 1—slag com-

Jan 1, 1955

By G. F. Fix

Oil and gas activity reached a higher peak in Indiana during 1940 than for any like period during the past decade. Major activity, as during 1939, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin, where most of the increase was due to field drilling in previously proven areas. The amount of wildcat drilling was about the same as for 1939. No new fields of any apparent consequence were discovered during the year, with the possible exception of the College pool, in southwest Posey County. Only one well had been completed in this area at the end of the year. About 10 ft. of saturated Aux Vases sandstone was drilled in this well and the initial production was I00 bbl. of oil a day. Other discoveries during the year 1940 include: St. Thomas, in southwestern Knox County, where four McClosky wells, ranging from I00 to 300 bbl. a day initially, were com-pleted; Buff kin, in central Posey County, with 11 oil wells and 5 gas wells completed; and new developments in two old areas —Randolph County (part of the old Trenton field) and Gentryville, northwestern Spencer County, where some oil was found many years ago. The St. Thomas field proved disappoint-ing, with very spotty production from the McClosky horizon of the St. Genevieve limestone at a depth of about 1875 ft. The discovery well flowed 362 bbl. a day ini-tially. At the end of the year the field was pretty well outlined by dry holes and some inside locations were dry. The Buffkin pool also proved spotty, with production from shallow Pennsylvanian sands and from the Basal Pennsylvanian Mansfield sandstone, the latter at a depth of approximately I175 ft., with small production from the Cypress sandstone of Chester age. Oil wells in this pool are small, ranging from 25 to 75 bbl. a day. The Randolph County area, on the east side of the Trenton gas field, showed some promise for a commercial gas field, with four completed gas wells having cumulative initial flows of about 1,200,ooo cu. ft. a day. The area appar-ently was not depleted during the Trenton boom at the turn of the century, since casing pressures are about as high as the virgin pressure in the old field. Elsewhere the pressure has dropped as low as 5 pounds. The Griffin field received most of the drilling during 1940, with 163 completed oil wells. This field now covers about 3200 acres on the Indiana side of the Wabash River and is not as yet completely delimited. It produced the major part of Indiana&apos;s oil during the year—a total of 3,594,000 bbl. At the end of 1940, there were 253 producing wells in Griffin. New Harmony had five completions for a total of 24. The Rockport field, in Spencer County, continued to be actively developed and had a total of 45 gas wells and 9 oil wells at the end of the year. Oil in commercial quantities had not been found in the field previous to 1940. Total gas production for the year was 394,470,000 cubic feet. In all, 521 wells were drilled in the state during 1940, as compared to 377 for 1939. Of this number 248 were oil wells, 77 were gas wells and 196 were dry. Divided into

Jan 1, 1941

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days&apos; rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth&apos;s crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975