Search Documents

By Hans Lundberg

By electrical prospecting, orebodies that do not otherwise manifest themselves at the surface may be located. Conditions favorable to success with the methods are: Favorable geological conditions, such a proportion of minerals of good electrical conductivity in the orebody as will render the latter materially a better conductor than the enclosing rock, situation of the orebody within the range of influence of the electrical currents used and in proportion to this range a sufficient area of horizontal cross section of the orebody. The result is to permit of spotting drill holes accurately and to save the expense of drilling barren ground. THE art of prospecting, like other branches of mining, has developed rapidly during the last ten years, mainly because of the advancement of mining geology, but also because of the development of "geophysical methods," which are based on the different physical characters of minerals and rocks, e. g., specific gravity, elasticity, and magnetic and electric properties. These methods have proved of great value, especially in countries where the rock is covered by soil and direct geologic investigation is out of the question. In prospecting for orebodies, the methods based on studying differences in electrical conductivity have proved most successful; for which reason, the methods of electrical prospecting have been subject to the most energetic and systematic work, especially in Sweden. This paper gives a brief description of the methods of electrical prospecting now in use, especially the new electromagnetic methods, which have not been described before. The great differences in the electrical properties, especially in conductivity, between ore minerals and rock minerals are fundamental to all methods of electrical prospecting, for which reason, the electrical conductivity of ore minerals and rock minerals has been carefully studied in connection with and previous to the development of the various methods of prospecting with electricity. Ore minerals with a metallic luster, such as chalcopyrite, iron pyrite, galena, specular iron, magnetite, etc., also graphite and a number of cows, have considerably higher conductivity than the surrounding rock and soil (see Table 1). The figures of the table denote the specific resistance W, expressed in ohms for a cube with an edge of 1 centimeter.

Jan 7, 1925

By David White

Attention has been given to the sources and supply of the raw vegetal matter and the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic dct,ris, and of the biochemical changes undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of this debris, and the deposition, as sediments, of the undecom-posed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal so1ution. Biochemical Changes End in Peat Formation The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly uncon-solidated, and their water content is great, amounting to over 85 per cent, near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed. Geochemical and Geophysical Changes in Buried Deposits Subsequent Changes " Dynamochemical" The changes which subsequently take place through dehydration, lithification, and simultaneous progressive chemical alteration, by which organic sediments are advanced to brown lignite, subbituminous, bituminous, semianthracitic, and graphitic ranks, are geochemical and geophysical, and the process, which really is metamorphic,2 takes place under dynamic influences. In fact, the essential changes, including loading,

Jan 1, 1925

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By L. C. Aycock, J. Hunter, P. M. Lyons

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By R. Al-Hussainy, H. J. Ramey

Previous gas well test analyses have been based mainly upon linearizations of ideal gas flow results, although a method for drawdown analysis based upon real gas flow results has been proposed. Linearizations based upon ideal gas flow require estimation of gas physical properties at Tome sort of average pressure, and implicitly involve the assumption that pressure gradients are small everywhere in the reservoir. A new real gas flow equation has been developed by means of a substitution which couples presTure, viscosity and gas law deviation factor. This sub-stitution has been called the real gas pseudo-pressure. Use of the real gas pseudo-pressure leads to simple equations describing real gas flow which do not contain pressure-dependent gas properties, and which do not require the assumption of small pressure gradients everywhere in the flow system. Equations required to determine flow capacity, well condition and static formation pressure from pressure drawdown and build-up tests with the real gas pseudo-pressure concept are presented. Also shown are applications of the real gas pseudo-pressure to back-pressure testing, the gas materials balance and rigorous determination of average gas properties for previous gas flow equations. Included are sample calculations for well test analyses. INTRODUCTION A recent study' of the flow of the transient flow of real gases in ideal radial systems showed that it is possible to consider gas physical property dependence upon pressure by means of a substitution called the real gas pseudo-pressure. The substitution has the advantage that it enables engineering solutions for steady and transient flow of real gases that are more accurate and general than those previously available. The solutions are particularly important for the case of gas flow in tight, high-pressure formations under large drawdowns. Even for more ideal flow conditions, the real gas pseudo-pressure concept leads to important rules for finding average gas physical properties pertinent for older well test analyses. Ref. I provides a detailed study of the theory behind the real gas flow correlations to be used in this paper. The purpose of this paper is to provide necessary engineering forms for use of the real gas flow results, and to illustrate applications. The following considers flow of real gases in an ideal radial flow system. It is assumed that: (1) formation thickness, porosity, water saturation, absolute permeability, temperature and gas composition are constant; (2) gas compressibility and density are functions of pressure as described by the gas law pv = znRT; (3) gas viscosrty is a function of pressure; (4) effective permeability to gas may be a function of pressure to account for liquid condensation; (5) condensate is immobile; and (6) the formation has no dip.

Jan 1, 1967

By J. Hunter, P. M. Lyons, L. C. Aycock

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

amounted to about 2000 metric tons. The total output is increasing from year to year. Marine salt is now produced in Haiti in quantity sufficient to supply nearly all the requirements of this Republic, so production tax is now collected. Central America Guatemala-The major production of salt in Guatemala is solar salt derived from sea water, but the Indian population prefers salt derived by boiling coastal marine earth. Salt is taxed by the Government. The industry has been beset by controversies in recent years, especially following the revolution of October 1944. The Government issued a decree in August 1940 designed to control production and price of salt. The creation of a salt consortium was provided for and marketing was to be governed by production quotas. It is understood that the Government pool was later dissolved and the industry is now under older laws whereby production and sales have no limits. South America Panama-Output of salt in Panama in a very recent year was 11,000 net tons of solar-evaporated sea salt. A Government bank is in charge of output and distribution of the product. Colombia-Rock-salt deposits are known in five places-Zipaquira, Nemocon, and Sesquile, in the Department of Cundinamarca, the Cumural y Upin near Restrepo, and San Miguel y Barital, near Medina in Meta Intendency. The latter deposit never has been worked on account of its inaccessibility. Saline springs are worked in four locations. The largest producer among marine salinas is Manare but it is now planned to make Bahia Honda the largest. Some evaporated salt is made in vacuum pans. The deposits at Zipaquira, Nemocon, and Sesquile are believed to occur in the domal type of deposit. All the salt resources are under Government control. Venezuela-The salt industry in Venezuela is under Government control and is taxed. Taxes in recent years, however, have been reduced for salt used in curing hides and salting meats, fish and fish products. Production has approximated 25,000 metric tons yearly but may now be considerably above that figure. The basin on the peninsula of Araya, State of Sucre, which at present is the only important source of salt, could produce at least 175,000 metric tons if more ground were provided-a larger supply than the entire country could consume. This unique landlocked basin of nearly 1000 acres lies 12 ft below sea level. Ecuador-Salt is a Government monopoly in Ecuador and is produced chiefly by solar evaporation close to the shore. The main producing center is on the Santa Elena peninsula, which supplies about 90 pct of the salt. Small fields are at Punta Arenas, Payana, and Chara-

Jan 1, 1949

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches 'carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on, this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable .to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, .and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix .2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smiths have pointed out, that the lamellae delineate the [210] planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By R. C. Earlougher

Based on laboratory tests conducted with the use of fresh core samples as well as a considerable amount of field data obtained from numerous water floods in northeastern Oklahoma, it appears that for any given oil saturation there is a critical maximum velocity above which the oil-recovery efficiency falls off very rapidly. In effect, when a water flood is operated above this critical velocity, the injected water-oil ratio rises extremely fast, thus shortening the economic life of the flood and reducing the ultimate oil recovery. This critical velocity apparently varies considerably with the percentage of oil saturation of the sand, so that in effect the higher the oil saturation at the beginning of a flood the higher the velocity that can be used successfully. In reviewing several of the earlier floods in the Mid-Continent area, it is concluded that most of the failures were due to two things: (I) too low an oil saturation, such as 30 per cent, and (2) too high water-injection rates, Although considerably more field data are necessary to establish definite limits, it would seem that the proper field injection rate for a 330 by 330 or 440 by 440-ft. spacing varies from approximately I bbl. per foot of sand per day where the oil saturation is as low as 30 per cent up to 5 bbl per foot of sand per day when the oil saturation is as high as 45 to 50 per cent, Introduction With secondary recovery by water-flooding receiving more and more attention throughout the industry, a greater working knowledge of multiphase flow under field conditions becomes more and more necessary A great deal of research has been carried on in highly idealized laboratory conditions, from which certain trends have been indicated, but with few exceptions no direct application to field use has been reported. widely varying conclusions have been drawn from the mass of idealized laboratory experiments and often this divergence apparently was due to the neglect of connate or interstitial water. Since interstitial water is such an important factor in water-flooding operations, it then follows that any laboratory flooding experiment must necessarily take it into account; and since it is difficult to set up laboratory models to allow for interstitial water, the next best procedure is to use fresh core samples for such tests. Even this procedure has its difficulties, inasmuch as it is possible to run only one flooding test on each sample, as each sample differs somewhat in character from all other samples. However, this disadvantage can be overcome to a large degree by the use of an extremely large number of samples. The next question that arises is: "IS it possible to get uncontaminated core samples having a true oil and water saturation like that existing in the reservoir?" If the sand under consideration is still in the primary stage of production, with a normal or relatively high amount of gas still in solution in the oil, probably it is not possible to get a nonflushed core. On the other

Jan 1, 1943

By R. Norman Orava

The strain-mte behavior of. the tensile yielding and flow characteristics of arc-cast polycrystal-line molyhdenum of pidrity > 99.97 pct was investigated in the range 10-6 to 10-1 sec-1 at 243o, 293o, and 373oK for two grain sizes, 0.027 and 9.098 mm. For 0.998 mm, the strain-mte dependence of the lower yield stress can be described by a straight line of the jowl a, = a + 0 log e over the whole range of strain rates examined. However, for 0.027 mm, the data fit several consecutive linear relationships of the above form. The previous association of these different linear regions with different rate -controlling mechanisms is questionable for molyhdenzdm. The senlilog strain-rate dependence of the yield stress is consistent with Hahn's model for yielding when the stress dependence of the mobile dislocation density, pr, is taken into account. Since p', from rate -cycling experirnents, is found to be relatively insensitive to stress for single crystaIs, the obserzied log-log dependence of their yield stresses is also in agreement with the model. A correction for the stress dependence of p' changes the activation oolurrze for yielding from a zero to a more realislic inverse function of stress where the Peierls mechanism is believed to be rate-controlling. The gmin-size dependence of the lower yield stress is not a monotonic junction of strain rate. RECENT experimental evidence' has revealed that the strain-rate dependence of the tensile lower yield stress, a,, of commercially pure ni- obium and tantalum tested at room temperature can be described by several consecutive semilog relations of the form: sv =a + ß log € [1] where i is the applied strain rate and a and 0 are constant Over only relatively small ranges of strain rate. Three linear regions were found for niobium and four for tantalum. Each linear region was interpreted as being associated with a different rate-controlling mechanism on the basis of the current

Jan 1, 1964

By Roy Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe¬rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By C. C. Templeton, S. S. Rushing

Methods previously developed for the study of air-liquid displacements in microscopic capillaries (inner diameters of 3 to 40 microns) have been used to investigate oil-water displacements in capillaries initially filled with water. Displacement calculations assuming perfect displacement and no capillary pressure hysteresis yielded oil effective viscosities smaller than the macroscopic viscosities. For a given liquid pair, the oil effective viscosity decreased both with decreasing capillary size and with increasing oil-water viscosity ratio. This behavior can be explained by the existence of an annular water film (20 A to 260 A thick) on the capillary wall. When the capillary was first filled with oil, the ratio of the oil effective viscosity to the normal oil vircosity was highest for the first water displacement and decreased with subsequent displacements. Sometimes the oil effective viscosity ratio during the initial water displacement was greater than unity. INTRODUCTION In a previous paper1 a technique was described for studying air-liquid and liquid-liquid displacements in very small capillaries of uniform diameter, in the hope that such microscopic data would further the understanding of the nature of multiphase fluid flow through porous media. That paper contained comprehensive data for air-liquid displacements in Pyrex capillaries, with a few data for oil-water displacements in capillaries initially filled with water. The purpose of this paper is to present more complete results for oil-water displacements in capillaries initially filled with water, and to describe for the first time such observations in capillaries initially filled with oil. In this way the effect of the wetting history of the system upon the displacement process may be studied. METHODS The basic techniques employed were described in the previous paper.1 The measuring procedure and the working equations will be briefly summarized here and a few modilications will be pointed out. For the present study, temperature control within 0.l °C was obtained by placing the microscope and its immediate accessories in a thermostated air bath made of a steel frame covered with plexiglas. The water and oils used in this work were the same as in the previous paper,1 with the addition of "Medium Mineral Oil, U.S.P. supplied by the Harshaw Scientific Co. When the first liquid was introduced into the horizontal capillary, the air-liquid static capillary pressure Poc was measured along the observable length of the capillary. From the relation Poc = 4y cos 0/d, the capillary diameter d could be calculated from Poc if the "microscopic" air-liquid boundary tension, To = y cos On, was taken as equal to its known "macroscopic" value. This calculation involves assuming that cos 6 = 1 and that capillary size or the resulting high interfa-cial curvature has no effect on surface tension, or y cos 6, as was verified by our work, and also by that of Cohan and Meyers on air-liquid-solid systems. For several capillaries these calculated diameter values were compared with values measured visually with a filar micrometer eyepiece. For a given capillary the average values for the two methods agreed within 1 or 2 per cent, but the visual values were less reproducible than the calculated values. Further the calculated values were much less subject to personal bias and took into account any slight ellipticity that might be present. Hence diameters calculated from air-liquid Poc data were used throughout this paper. The second liquid was introduced in such a way that a single spherical interface separated the two liquids. Displacements were always made with a constant pressure, Pt, between the ends of the capillary. The times (t) at which the interface passed certain

Jan 1, 1957

By Luiz C. Correa da Silva, Robert F. Mehl

A. D. Le Claire and R. S. Barnes (Atomic Energy Research Establishment, Harwell, Didcot, Berks., England)-—This much awaited paper admirably confirms that the Kirkendall effect is a true diffusion phenomenon and likely to be found in all diffusing systems. The most likely explanation put forward so far to account for the shift of interface is that the two components of the system, diffusing in opposite directions, do so with unequal rates so that there is a net loss of material from that half of the diffusion zone rich in the more rapidly diffusing component. This loss is accompanied, and at least partly compensated for, by a closing up or decrease in volume of this latter half of the diffusion zone and an expansion of the other half so as to tend to keep constant the overall volume per atom. This is manifest as a movement of the original interface. If this is a true picture of what is taking place then there are at least two important matters requiring further study."1—The quantitative relating of the observed shift with the independently measured separate diffusion coefficients of the two diffusing species."2—A detailed study of the mechanism and characteristics of the closing up process."We would like first to make a few remarks pertinent to these topics. In connection with the first of these, it is a pity that more and detailed measurements were not made on the Au-Ag system, the only one for which the separate diffusion coefficients of the two species have been measured.'" One of us (A. D. Le C.) has calculated from Johnson's results the shift to have been expected in samples D.2 and D.3. Darken4 showed that the velocity v with which the markers move is related to the separate diffusion coefficients Dau, Dag, by the eauation:"dN"v = (Dag — Dau "dx"dN"where .is the concentration gradient at the mark-ax"ers. Under certain conditions,4, 20 it can also be shown that:"Xm"v = "2t"where x, is the total marker shift after time, t:"dN". . xm = 2t (Dag — Dau) [9]"dX"Johnson measured Dag and DAu in a chemically homogeneous alloy and so his reported figures represent the true or ideal diffusion coefficients"; the same quantities in eq 9 represent the actual diffusion coefficients as would be measured in the presence of a chemical concentration gradient, so we need to multiply Johnson's reported values of Dag and Dau by the"1 before insert-dlogN "ing them in eq 9. 7 is the activity coefficient of Ag at the concentration prevailing near the markers which we shall assume to be - 50 pct. The values of the thermodynamic factor for N = 0.5 and the temperatures at which D.2 and D.3 were annealed were obtained from thermodynamic data quoted by Darken.' aN/ax was computed from the coefficient of inter-diffusion of Au and Ag given by Johnson on the assumption that in the samples D.2 and D.3, the concentration distance curve could be represented by the standard equation:""No is the original difference in concentration between the two halves of the couple, and + is the error or probability function."aN/ax at x = 0 is then given by:"adN/dx "2/nDt"and we assume that this represents the concentration gradient at the markers, although it is probable that the figure is slightly high."When all the appropriate quantities are inserted in eq 9, we find that the expected shifts are: for D.2, 0.0134 cm and for D.3, 0.0119 cm."The agreement between these results and those

Jan 1, 1952

By M. Prats

This paper presents a method for obtaining the correct values of the breakthrough sweep efficiency of the staggered line drive, taking into account the proper shape of the breakthrough streamline. Results obtained were different from those previously published, which were obtained by using an inexact shape of the breakrhrough streamline. INTRODUCTION In Section 9.31 of Muskat's' The Flow of Hotnogeticous Fluids Through Porous Media, it is stated that in a staggered line drive flood "the streamline of highest average velocity [is] the line of centers between input and output wells" (see Fig. I). Muskat used this concept to determine the relationship between the breakthrough sweep efficiency and the geometry of the staggered line drive pattern. Although it is clear from symmetry considerations that the breakthrough streamline passes through the midpoint between input and output wells, it is equally clear, as shown in Fig. 239 of Ref. 1, that the breakthrough streamline is not represented very well by the straight line joining the input and output wells. Therefore, it is desirable to determine the proper relationship between the breakthrough sweep efficiency and the pattern geometry by using the proper shape of the breakthrough streamline. METHOD OF SOLUTION It was found that the effect of the geometry of the staggered line drive on the breakthrough sweep efficiency can be investigated easily by making use of the method developed in Ref. 2. With this method, it can be shown that the general complex potential for the staggered line drive, which can be considered as a rectangular five-spot, is given in the coordinate system of Fig. 1, by O(z) = In cn(z\m) = +(x,y) + i $(x, y) . (1) where z = x + iy, +(x, y) is the potential distribution and $(x, y) is the stream function. The function cn (zm) is a Jacobian elliptic function of parameter m and has simple zeros at z,. = (2n + 1) K + 21iK and simple poles at z, = 2nK + (21 + 1)iK. Thus, the complex potential behaves like a(z) = ln(z - zr.) in the neighborhood of the production wells and behaves like a(z) = - ln(z - Z,) in the neighborhood of the injection wells. Since (z - z1.v) = rll.ei, we note that the potential + has the proper logarithmic behavior near the two wells, while the stream function $ varies with the angle, decreasing clockwise around the production well and increasing clockwise around the injection well. The functions K(m) and K'(tn), related by K(m) = K'(m,), where m + m, = 1, are known as the complete elliptic integrals of the first kind. By use of other properties of the Jacobian elliptic functions, the general stream function distribution for the staggered line drive can be obtained from Eq. 1: From the Jacobian elliptic function values, sn(0lm) = 0 dn(O(m) = cn(0jm) = 1, and f[K'(m)Iml = 03, it follows that the stream function given by Eq. 2 satisfies the proper symmetry conditions near a production well P located at [K(m), 01 and an injection well I located at [0, K' (m)]. That is, the line IOP in Fig. 1 is a streamline with value G (0. 0) = -0. and the straight lines connecting I and P to the point [K(m), K' (m)] is a streamline of value $[K(m), K' (m)] = -7/2. Similar symmetry conditions are obtained near other wells. It should be nuled that for m = m1, = 0.5, Eq. 2 reduces to the stream function distribution of the regular five-spot given in Ref. 7. SHAPE OF THE BREAKTHROUGH STREAMLINE It is apparent, from symmetry considerations, that the breakthrough streamline ($,) passes through the point [K(m)/2, K' (m)/2]. Its value there is so that the shape of the breakthrough streamline $,, is given by

Jan 1, 1957

By H. Margolin, E. Ence

Two versions of the Ti-Mn binary diagram have been published recently.' , -0th diagrams show two compounds in the region between 40 and 70 wt pct Mn, but disagree as to the reaction in which these compounds are involved. The investigation of the manganese-rich portion of the Ti-Mn binary diagram was undertaken at New York University as part of an investigation of ternary systems with titanium and manganese in order to determine which of the proposed diagrams is correct. A number of alloys between 31 and 70 pct Mn were prepared in a manner similar to that described by Cadoff and Nielsen; except that low currents (110 amp in argon atmosphere) and long melting times (up to 20 min) were used to prepare the alloys. Compositions were determined from weight-loss data, assuming all loss as due to manganese. Heat treatments were carried out with relatively large pieces, since there was a tendency for manganese to be lost during heat treatment. When X-ray diffraction data was to be obtained, the central parts of heat-treated specimens were used to make filings or powders which were not heat treated. Specimens were heat treated from the as-cast state. Heat-treatment times were as follows: 1150°C, 1 day; ll00°C, 2 days; 1000°C, 5 days; and 900°C, 15 days. It should be noted that equilibrium was not attained at 900°, 1000°, and in one case, at 1150°C. Metallographic specimens were electrolytically polished and strain etched by a technique described elsewhere.' At least four, and possibly six, phases were found in the region investigated. On the basis of information available at this time, a completely self-consistent diagram cannot be constructed, and therefore data are presented only for those phases which have been identified by both X-ray and microstruc-ture. Of the compounds detected, the one highest in manganese is the Laves phase, TiMn,, which is hexagonal with a MgZn, type of structure.V he diffraction data for TiMn2 from a 70 pct Mn alloy annealed at 1150°C are shown in Table I. The c/a ratio and parameters of TiMn2 agree well with those of Wall-baum hnd Rostoker et al. The values obtained here are c/a = 1.641, a = 4.825A. Another compound is the y-phase which is estimated to contain about 60 pct Mn. The y-phase has a structure which is identical to that of TiMn, with c/a = 1.639, a = 4.906Å. The fact that y has a Laves-type lattice would suggest that TiMn, has a range of solubility which extends from the composition of TiMn2 (69.6 Mn) to that of y (60 pct Mn). However, this could not account for microstructures which, in the 60 to 70 pct Mn region, show several phases in both the as-cast state and after annealing at 1150°C. Fig. 1 shows a two-phase structure of a 60 pct Mn alloy annealed at 1150°C. The phases present are y (white) and e (dark). If y were TiMn, then, according to Rostoker et al.,' the second phase of Fig. 1 should be P-Ti. The diffraction data for the 60 pct Mn alloy of Fig. 1 are shown in Table I. The starred d-values are from the e-phase and these lines do not correspond to those of &Ti. Comparison of as-cast and 1150°C microstructures of the 60 pct Mn alloy indicates that e precipitated from y. Since y has a

Jan 1, 1955

By D. L. Martin

THAT small amounts of impurities have a harm-J- ful effect on the malleability of metals and alloys is well-known. One common type of em-brittlement involves the formation of a small quantity of eutectic at the grain boundaries, and is typified by sulfur embrittlement of nickel. Another example of eutectic embrittlement—sulfur embrittlement of cobalt—is described in this report. In the preparation of specimens for a study of Co-Pt alloys, it was observed that the hot swagabil-ity of the alloys appeared to be influenced by the grade of cobalt used as melting stock. The cause of the hot-shortness was not traced to any particular impurity, although sulfur was suspected.' The damaging action of sulfur on the malleability of cobalt has not been generally recognized,'; in spite of the fact that the Co-S phase diagram8 eveals the same basic conditions—low solubility and eutectic formation—responsible for sulfur embrittlement of iron and nickel.7, 8 Apparently sulfur embrittlement has not been a serious problem in the fabrication of cobalt alloys. One related factor is likely the limited commercial experience with high cobalt alloys, since the predominant use of cobalt has been in alloys containing less than 75 pet Co. A series of Co-S alloys was prepared and studied to establish the effect of sulfur on the hot working characteristics of cobalt. Specimens, 5/8 in. diam by 4 in. long, were prepared by vacuum melting in magnesium oxide crucibles and casting in a copper mold. Two grades of low sulfur electrolytic cobalt were used as the basic material for the study, one from Johnson, Matthey and Co. and the other from the International Nickel Co. Each contained about 99.5 pet Co and had a nominal sulfur content under 0.005 pet. The sulfur was added initially as cobalt sulfide powder. Later, some low sulfur alloys were prepared by diluting the high sulfur alloys with cobalt. Trouble was experienced in controlling the sulfur content. Apparently much of the cobalt sulfide powder was lost during melting, as most of the samples contained a lower sulfur content than was added. The alloys were evaluated for hot brittleness by heating to 1000°C in a hydrogen furnace and swaging in air. The results of these tests are summarized in Table I. All the alloys containing less than 0.008 pet S were successfully hot swaged to 1/4 in. diam. The bars containing more than 0.015 pet S could not be swaged because of the formation of intercrystal-line cracks similar to those illustrated in Fig. 1. Examination of the microstructure of the cast bars revealed cobalt sulfide eutectic at the grain boundaries, Fig. 2. The sulfide was not always continuous at grain boundaries in bars that were hot embrittled but, in general, the particles did form a network that could account for the brittleness above the eutectic temperature, 880°C. There is no question about the brittle nature of a specimen exhibiting a continuous sulfide network such as is shown in Fig. 2b, though a sulfide distribution similar to that in Fig. 2a is marginal. This particular bar cracked when hot-swaged. However, other bars with lower sulfur content but with some sulfide phase at grain boundaries were successfully worked. The reduction of area of a hot tensile test specimen was also found to be a sensitive indicator of sulfur embrittlement. The variation of reduction of area with sulfur content is shown in Fig. 3 for specimens fractured at 900°C in an evacuated capsule. The ductility of cobalt is greatly reduced when the sulfur content exceeds 0.005 pet. Similar results were obtained for alloys tested at 800°C, below the eutectic temperature. The upper sulfur embrittlement limit of 0.015 pet, Table I, agrees with the observation of Kalmus8 hat

Jan 1, 1957

By Dennis Peterson

INTRODUCTION The business arena has dramatically changed for most producers and consumers of commodities. International debt, currency shortages, political upheavals, etc., require corporations today to be sophisticated and flexible enough to change their purchasing and sales techniques in order to maximize returns. Many external factors, such as interest rates, trading partners, currency changes, and government edicts, can have an adverse effect on a company's bottom line. Totally out of a company's ability to control or predict, these. factors force the commodities based corporation to constantly re-evaluate its operating scope and domain. The principle of back-yard only operations and the laissez-faire with blinders style of management is no longer a viable way to run a business. The industrial world has been operating for the past 10 to 15 years as though there were no commodity nor raw material crisis. For developed countries the primary products sector has become marginal, whereas it was central in the first half of the century. A radical change in the method of doing business is necessary to offset a depression in the industrial economy. The risk of collapse may be heightened by a banking crisis caused by massive defaults on the part of commodity producing debtors, whether in the third world or in our own farm producing sector. The raw materials economy has become divergent with the industrial economy. This is a major change in the world economy with tremendous implications in both developed and developing countries for economic and social policies and economic theories. Basic competition issues, such as low labor costs, are likely to become less of an advantage in international trade. In developed countries these costs are going to account for a smaller portion of total costs. The total costs of automated processes are lower than those of traditional plants with low labor costs. Automation in the commodities sector eliminates the hidden but high cost of not processing at capacity created by poor quality, rejects and maintenance for product change-overs. The cost of capital will become increasingly important in international competition. Over the last ten years the U.S. has become the highest cost country in this area. Reversing the U.S. policy of high interest rates and costly equity capital should be a priority for management decision makers. In the rapid industrialization of this century, Japan developed by exporting raw materials, (principally, silk and tea), at steadily increasing prices. Germany developed by leap frogging into the high-tech industries, mainly in electricity, chemicals and optics. The United States did both. Both avenues are blocked for today's rapidly industrializing countries because (a) the deterioration of the terms of trade for primary products, and (b) it requires an infrastructure of knowledge and education far beyond the scope of a poor country. Many explanations exist for the explosion of international money flows. The shift from fixed to floating exchange rates in 1971 may have given initial impetus by inviting currency speculation. The surge in liquid funds flowing to petroleum producers after the oil shocks of 1973 and 1979 was definitely a major cause. There can be little doubt that the U.S. government deficit also played a big role. The American budget deficit has become a massive void, sucking in liquid funds from all over the world and making the U.S. the world's major debtor country. In reality, a trade and payments deficit is actually a loan from the seller of goods and services to the buyer, that is, to the U.S. From now on, the global ramifications of business will have to be treated in economic theory and business policy alike. Economic theory teaches that the comparative advantage factors of a real economy determines operative and financial policy. These comparisons -- labor costs, productivity, raw materials cost, energy costs,

Jan 1, 1990