Search Documents

By Robert H. Richards

Jan 1, 1897

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

By A. C. Backeberg

There is no South African code for the design of reinforced concrete headframes, and all those erected have been designed on a uniform basis which, up to the present, has tended to be conservative. With certain exceptions designs have generally conformed with British Standard Code of Practice C.P. 114. In the design of reinforced concrete headframes the following loads are taken into account:

Jan 11, 1961

By P. H. Dudley

IN giving a brief account of the experiments in progress to inquire into some of the facts in regard to "railway resistances," recently commenced upon the Lake Shore and Michigan Southern Railway, with the dynagraph (which is essentially an instrument recording upon paper the force required to draw a train, at all speeds, marking the time in short intervals, so that the force absorbed due to any

Jan 1, 1876

By J. A. Corbyn

An analysts of mining investment from the point of view of financial optimization is presented. The method uses differential equations to describe financial performance rather than the more usual method of modeling mine accounts from year to year. The analysis shows there is a optimum mine life that can be easily determined if certain simplifications are made. Tables are given to facilitate computation of the optimum life.

Jan 1, 1985

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y', and E carbonitride has been confirmed and it has been found that y' is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part' reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,' this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* 'Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By Frank C. Smith

The following article covers the history of a metallurgical campaign, commenced in March, 1905, at the mines of the Socorro Bold Co., in the so-called desert region of Yuma county, Arizona. The results obtained were simply a function of necessity, as will be seen from the description of the local economic conditions and the character of the ores treated. The mines and mill of the Socorro Gold Co. are located near the small village of Harrisburg, about 60 miles from Congress Junction, Ariz., which, at the time this work was undertaken, was the nearest railroad station, and from which all supplies were brought by wagon through the desert, at a cost varying from $10 to $15 per ton in addition to the railroad freights. Wood, the only available fuel, cost $7 per cord. Water for all purposes was pumped to the plant from a well in the valley about 4 miles away. Under the Arizona law, a working-shift is 8 hr. Wages were $6 per day for foremen and mill-men, $4 per day for blacksmiths and engineers, $3.50 per day for miners, and $3 per day for shovelers and trammers. The ore consisted of quartz, in which, above the 250-ft. level, the iron-minerale were largely oxidized and some free gold was visible; below that level few traces of oxidation occurred, and pyrite constituted the principal mineralizer in the quartz, together with occasional pockets of galena and a few eccentric specks of covellite. The 20-stamp mill was equipped with plates for amalgamation, and three Standard tables for concentration. The tails from the tables mere elevated by a centrifugal pump to a launder, by which they were conveyed to a 60-ton cyanide-mill for further treatment. The cyanide-mill was erected at so great a distance from the stamp-mill that a separate crew of workers and a separate power-plant were necessary. No arrangement had been made for the treatment of the concen-

Jan 1, 1907

By GUY C. RIDDELL

ZINC, manganese, and aluminum received attention at the two nonferrous metallurgy sessions at the Annual Meeting. L.P. Davidson, general superintendent of the rebuilt Monsanto zinc plant, described its operation, which reflects Polish practice and is really a combination of electrolytic, Waelz, and retort procedure. Briefly, it embraces leaching of roasted concentrate with sulphuric acid, electrolysis of sulphate solution using Tainton lead-silver anodes with ?goulac? added to the electrolyte, treatment of tailing in Waelz kilns, and retorting of the recovered zinc oxide, casting furnace dross and residues. Recovery is good, equipment and maintenance costs low. Ferrate zinc that might be lost in the electrolytic process appears to be recovered as oxide in the Waelz treatment.

Jan 1, 1942

Jan 1, 1952

By Ernest Gayford

This is a nontechnical paper on flotation, subdivided under three general headings: (I) Definition of flotation; (2) what flotation is now doing in Utah; and (3) what is the future of flotation? Definition T. A. Rickard defines flotation' as "the act or state of floating," from the French flottaison, water-line and flotter, to float. The dictionary defines flotation as "the science of floating bodies." The flotation process is a method of concentrating ores by frothing. Weinig and Palmer,2 define flotation as follows: What is the flotation process? Briefly, it consists in the agitation of finely divided ore in water containing bubbles of air or gas, a small amount of oil and, usually, other reagents, soluble and insoluble; under these conditions the small particles of native metals, sulfides, arsenides, antimonides, selenides and tellurides show a tendency to attach themselves to the films of the bubbles, and are thus carried to the surface of the water. The oxidized gangue minerals, such as quartz, feldspar, limestone, hematite, etc., show much less affinity for the bubbles, are easily wetted by the water, and either remain in suspension in the water, or sink to the bottom of the vessel. If the bubbles are sufficiently stable they can be removed, carrying their load of sulfide-mineral particles with them. Thus there can be effected a separation of the two classes of minerals from each other, assuming that the grinding has been sufficient to unlock all of the particles of different composition. The separation does not depend upon differences in specific gravity of the various minerals; in fact, the sulfides are usually heavier than the oxides, and some of the heaviest sulfide minerals are the easiest to float. A particle of mineral may be so large, however, that its weight will counteract its affinity for the film of the bubble. In most cases the ore must be fine enough to pass a screen having at least 48 meshes to the linear inch. Taggart3 defines flotation as follows: Flotation is a method of wet concentration of ores in which separation of mineral from gangue is effected by causing the mineral to float at or above the surface of a body of liquid pulp while the gangue becomes or remains submerged. The method

Jan 1, 1928

By T. R. Lippard

PURE gypsum may be broken down into its constituents as follows: [ ] Standard specifications (ASTM Designation C22-25) state that a material shall not be considered gypsum if it contains less than 64.5 pct by weight of CaS042H2O. Anhydrite, the second calcium sulphate mineral found in nature, may be broken into its constituents as follows: [ ] PROPERTIES OF GYPSUM AND ANHYDRITE Pure gypsum is colorless to white but various impurities change its color to shades of gray, brown, red, or pink. It has a hardness of 2 in the Mohs scale and can be scratched with the fingernail. The specific gravity of pure gypsum is 2.3 to 2.4, so that rock gypsum, free from moisture, weighs about 145 lb per cu ft. Gypsum crystallizes in the monoclinic system in tabular crystals that exhibit good cleavage

Jan 1, 1949

By William E. Hughes, Roderick K. Davey

The objective of this chapter is to review and discuss interpolation techniques commonly in use in the mining Industry today, including simple examples. This chapter will not attempt to compare the relative accuracy of each technique as this subject has adequately been covered by several authors (Knudsen and Kim, 1967; David, 1974; and Barnes, 1979) When appropriate, methods will be compared relative to the results of simple examples and computational ease. The examples presented are based on metallic deposits. The techniques, however, are not restricted to metallic deposits and can generally be applied to nonmetallic ones. The purpose of interpolation, as applied to a mineralized deposit, 1s to extend the knowledge of the grade and geology of localized samples to an estimate of the grade and mineralogy of a larger block of ground or even an entire deposit. The word interpolation means to compute values between given values and is limited to that region between the known values. The distinction between interpolation and extrapolation is important and must be adhered to in the application of these techniques in general, the interpolation must be limited to the area enclosed by verified samples. The methods being discussed can be broadly broken into three categories. ( 1 ) geometrical methods, (2) distance weighting methods, and (3) geostatistical techniques.

Jan 1, 1979

By J. M. Steininger

The mechanism of flotation of sphalerite with sulthydryl compounds of different acidities has been interpreted in terms of chemisorption of unionized collector molecules on hydroxylated zinc surface sites. At a constant collector concentration of 1.5 x 10 -4 M, the upper pH limit of flotation has been found to be directly and closely related to the negative logarithm of the collector acidity constant, pKa The experimental results indicate that flotation is prevented when about 95% of the collector is ionized. At low pH, collector adsorption decreases because of the reduction in number of hydroxylated zinc surface sites. These two effects explain why sphalerite does not float with the more acidic sulfhydryl compounds. Typical anionic collectors for sulfide minerals are short chain xanthates or dithiophosphates which are nearly completely ionized in the generally alka- line flotation circuits.1,2 Flotation mechanisms have therefore been usually interpreted in terms of ionic collector adsorption and competition with ionic depressants of the same sign as the collector. A few attempts have been made, however, to consider adsorption of neutral collector molecules. Contact angle measurements obtained by Wark and cox3 have been interpreted by Cook and Nixon4 as representing adsorption of the free acid molecules on sulfide minerals such as pyrite, galena, chalcopyrite, and sphalerite. Cook and Nixon tried to show that the free acid concentration of the collector was substantially constant along the curves relating collector addition and minimum pH for bubble adherence. However, in a review of the subject,5 Sutherland presented new data on the flotation of pyrite with mercaptobenzothiazole which did not support the hypothesis of constant concentration of either collector ions or collector free molecules. He further showed that, with the assumption of constant occupation of surface sites, both theories lead to relations between pH and collector addition having similar mathematical expressions. In fact, with the more likely assumption of variable occupation of surface sites which results in more complex relationships, it appears impossible to

Jan 1, 1968

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By John T. Ryan

DEFINITE improvement in its accident fatality rate in the coal-mining industry was recorded during 1941, based on preliminary figures for the period from January through October. Total production during this ten-month period was approximately 91 percent of the total production in all of 1940. The ten-month accident rate for both bituminous and anthracite mining in 1941 was 2.15 killed per million tons of coal mined, compared with a rate of 2.66 for the full year of 1940. The bituminous rate decreased from 2.55 in 1940 to 1.99 in ten months of 1941, and the anthracite rate from 3.62 to 3.53 in similar periods. The decrease is more apparent for the bituminous branch of the industry, as the high figure in 1940 was due to seven major disasters which brought death to 276 men. The same number of major explosions during ten months of 1941 caused only 64 lives to be lost. The severity of the explosions has been lower this year but a definite need still exists for reduction in this type of accident.

Jan 1, 1942

By Arthur B. Foote

Ore production from the property of the Miami Copper Co. began early in 1911. Until 1925 this ore came from the so-called high-grade orebodies, which contained a little over 2 per cent. copper. This ore was mined by the following methods: 1. Top slicing after mining the peaks by square setting, which produced 4,524,347 tons, including ore from square setting. 2. Shrinkage stoping with sublevel caving of the pillars, which produced 2,230,577 tons. 3. Undercut caving with hand tramming, which produced 15,427,672 tons. Estimating December tonnage, the total ore mined to the end of 1929 will amount to slightly more than 43,000,000 tons. The first method was described by E. G. Deane' and the second by D. B. Scott,' and the third, together with a general description of the mine, by J. H. Hensley, Jr.' The geology of the district has been worked out by Dr. F. L. Ransome.2 The author acknowledges also the assistance of R. W. Hughes, assistant mine superintendent, E. V. Graybeal, chief mine engineer, A. J. McDermid and S. R. Burdick, engineers of Miami Copper Co., Miami, Arizona. Factors Influencing Selection of Mining Methods The mining method described herein was selected primarily with a low mining cost in view and was developed to avoid as far as possible dilution of the already very low-grade ore. In 1924, with the exhaustion of the high-grade orebodies in sight, it was decided to develop the low-grade orebody, which at that time contained 36,000,000 tons of ore assaying 1.06 per cent. copper, and had an area of 50 acres with an average thickness of 206 ft. overlain by an average thickness of 320 ft. of barren capping.

Jan 1, 1930

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

?ADAIR, ARTHUR C., Corp 4th Co., 1st. Training Bat., 154th Depot Brigade. ADAMS, HENRY, Major: Chemical Warfare Service. ARLUCK, A. A Headquarters, 1st Corps of Artillery. ASKIN, THOMAS B. H Ensign. BANKS, H. R., 2d Lieut Canadian Engineers. BAYLESS, G. E. S Supply Dept. U. S. Submarine Base. BELL, L. R Co. C, 302d Engineers. BELLIS, ARTHUR E., Capt Ordnance Reserve Corps. I BIRRETT, HOWARD, Lieut., Aviation Section, U. S. Signal Corps, Ellington Field. BOISE, PAUL T 2d Regiment, 24th Squadron. ?BRADLEY, CLARENCE I Convois Automobile Section 585. BROWN, GEORGE M Co. G lot Engineer Replacement Regiment. BUCKINGHAM, ALBERT U. S. S. " Coronet," S. P. 194, Section Base No. 7. BURNS J. J Co. 1-B, E. R. O. T. C. BURT, Co. B, let Engineers Replacement Regiment. ||BYERS, WHEATON B., 2d Lieut Ordnance Dept. CANTON, WILLIAM R., Sgt Headquarters Co., 80th F. A. CARSON, JOSEPH A., Capt A.S. S. R. C.' CHAPMAN, LEWIS C. Corp 29th engineers. CHETNEY, P. C., 2d Lieut 15th Bat. Headquarters Co. CHEVRILLON Louis French Red Cross. CHIDESTER, W. B., 1st Lieut 24th Machine Gun Bat. CHURCH, JOHN L., Capt 308th Engineers. CLAGHORN, D. MONTGOMERY, 1st Lieut 45th Engineers. CLAQHORN, JAMES L., Lieut Aviation Section, Signal Corps. CLARKE, ALEXANDER F U. S. Naval Aviation Service. COMINS, WALDO H. Ca t 41st Co., 164th Depot Brigade. COOK, FREDERICK A., Capt., Engineer Reserve Corps, Asst. to Div. Engr. 79th Division. COOPER, CLAUDE H. Capt C. A. R. C., 50th Artillery. COPELAND, N. R., Lieut. ||CORBY H.. G., 1st Lieut Co. D, 109th Supply Train. CORSA, BEAN, Capt Co. D, 612th Engineers. CORTESE, EMILIO Italian Army. COULDREY PAUL S., Corp British Expeditionary Forces. || CRAGIN, RODNEY S Co. E, 115th Engineers. CURRIE, JOHN M., Ca t Royal Engineers. || CUTTING, G. W., 2d Lieut U. S. Reserves, Field Artillery. V DARRINGTON, PAUL N., 1st Lieut U. S. Infantry. DAVIS, ANGUS W., Lieut-Col British Expeditionary Forces. || DAVIS, THORNTON, 1st Lieut 13th Field Artillery. ELAND, FREDERICK A., Major Engineer Reserve Corps. DOUGLAS, JAMES $ American Red Cross. DOVE, D. R., Candidate 21st Training Battery, F. A. C. O. T. C. Dover JAMES J 6th Co. C. B. DOWS, DAVID,Capt Coast Artillery, Officers Reserve Corps. || DRAKE, M. 6., 2d Lieut Headquarters Co., 325th Infantry. I || EMMERSON, E. Roy British Navy. EVERIT, RICHARD STURTEVANT Heavy Artillery Officers' Training Camp.

Jan 1, 1923

By J. H. Pratt

In a recent paper* on the origin of corundum associated with the peridotites of North Carolina, attention was called to the constant occurrence of the mineral, chromite, in these rocks. The field-data obtained during the preparation of that paper have been used largely in the present paper. During the past summer the general occurrences of chromite have been carefully studied, and those in North Carolina have been especially examined in the field. It is purposed to give, in this paper, the reasons why the chromite should be regarded as having been formed at the same time with the peridotites, having been held in solution by the molten mass of the peridotite, and crystallizing out among the first minerals as the mass began to cool. This theory is essentially the same as that advanced by me for the origin of the corundum associated with the peridotite rocks, and a similar line of reasoning has been used to substantiate the theory proposed. Investigations concerning the igneous origin of some of the ores have been materially aided, during recent years, by the skillful experiments of Morozewicz and Lagorio,§ and by researches that show us, more clearly, why we should regard a fused mass of rock as a liquid, having similar properties to an ordinary solution. These experiments have shown that a molten basic glass, similar in composition to the basic magnesian rocks, dissolves alumina readily, and that upon cooling, the first minerals to separate out are corundum and spinel.

Jan 1, 1900