Search Documents

By J. G. Henning

Following completion of planned mining operations at the Goldcorp Dome Open Pit Mine, a high-grade Shaft Pillar located in the pit highwall was recovered. Mining of this Shaft pillar faced numerous rock engineering design and implementation challenges due to its remote position on the highwall and the presence of mine workings within the wall. The case example presented in this paper discusses the geotechnical investigation performed at the site, novel measures undertaken for installation of ground support required for rockmass reinforcement and for worker protection, as well as operational challenges to successful mining of the Shaft Pillar.

May 1, 2009

By William S. Sanner

A demonstrated reserve base (DRB) of bituminous coal suitable for cokemaking has been estimated based on the latest published information on U.S. coal reserves. Bureau of Mines analyses of raw coalbed samples were used to classify the coals as low-, medium-, and high-volatile bituminous and grade them as premium, marginal, and latent coking coals. Coal rank was used as the basis for identifying coking coals, and ash and sulfur content were used to determine coking coal grade. The demonstrated reserve base of coking coal for the entire United States is 162.67 billion tons. However, only 18.96 billion tons are premium (metallurgical) grade, and between 80 and 99 percent occurs in the Eastern States. The demonstrated reserve base of marginal-grade coking coal is 31.3 billion tons; more than half the marginal reserve base is in the Eastern States, and most of the medium- and low-volatile marginal coals are in the Eastern States. The Eastern and Midwestern States contain most of the latent-grade DRB of 112.4 billion tons; most (106.6 billion tons) is high-volatile coal, and 98 percent of the medium- and low-volatile latent coals occur in the Eastern States. Based on the worst assumption, which assumes that only premium-grade coals are used for cokemaking, the DRB for high-volatile coal would suffice for 127 years, the medium-volatile coal for 80 years, and the low-volatile coal for 83 years.

Jan 1, 1979

Conservation and environmental issues are raising their profile with respect to both demand restraint and electricity supply options. In New Zealand, conservation pressures and energy efficiency need to be seen in relation to the supply system currently in place which has capacity for economic supply of electricity in quantities substantially in excess of the current market. Consequently, energy efficiency and conservation need to be interpreted in relation to the supply system as well as in relation to end use. The relationship between the environment and conservation is strongest when new generation is required. New Zealand's electricity supply system consists of a large proportion of hydro production and this has significant environmental benefits when considered in relation to concerns of global wanning and the greenhouse effect. However, environmental trade-offs in supply options need to take account of both the efficiency of electricity end use, the trade-off between hydro and thermal generation and the inter-regional effects of shifting development options from one region to another. The Electricity Corporation has a high level of consciousness with respect to environmental and conservation issues and this paper demonstrates its own moves to maximise energy efficiency and illustrate the environmental trade-offs for supply.

Jan 1, 1990

By Tracy Brettmann

A new method for estimating ground vibrations caused by pile driving was developed as a result of a vibration monitoring program performed for a large pile driving project. The method is accurate, rational and theoretically based starting with energy actually transmitted to the pile (not the rated or operating hammer energy). This energy is then assumed to be transmitted to the soil in the form of surface waves that attenuate from both geometric and material damping. The main input parameters for this method include the energy transmitted to the pile and the dynamic properties of the soil (wave velocity, material damping, and unit weight). In this study we concurrently measured both: (1) pile driving of 14-in.-square, 65-ft-long precast concrete piles with a Pile Driving Analyzer?, and (2) vibration levels at various distances away from the piles during driving. A geotechnical study for the site was also performed that included measurement of the dynamic soil properties using both crosshole and seismic cone testing. This paper presents the data obtained from the study and compares the results to the values estimated using this new method. Vibrations from pile driving is a serious matter that impacts virtually every pile driving project. It is important that accurate methods for estimating ground vibrations be available to engineers and contractors.

Jan 1, 1999

By Madan B. Karkee

The understanding and the development of sound theoretical basis concerning the pile foundations has been phenomenal during the past few decades, considering the thousands of years the piles have evidently been in use. The importance of the quality assurance and the need for verification of load bearing capacity is being further reinforced rather than undermined by these developments. This is evidenced by significant developments made in the pile load test technology in recent decades, making it possible to make judicious selection of a test method, or a package of test methods, suitable for a given situation. The selection depends on the objective of carrying out the test and the reliability desired. Presently, the possible selection ranges from dynamic to static methods. The extent of dynamic effect in a test can be reckoned based on a dimensionless parameter defined as the 'relative duration'. Examples of different load tests are given for illustration of the different methods currently in use.

Jan 1, 1997

By Turgut Yalcin

"High-grade concentrates are achieved in flotation columns primarily due to the use of thick froth layers and wash water, both of which facilitate the drainage of hydrophilic minerals from the froth. However, conventional columns employ tall, non-agitated recovery sections for bubble-particle attachment that require high headroom and special gas spargers as well as imposing particle size limitations. These disadvantages can be all alleviated by carrying out the recovery part of the process in a mechanical or pneumatic cell which generate froth more conveniently and efficiently.This paper describes the combining of mechanical and column flotation in a single unit and discusses the influence of various parameters on the performance of the system.INTRODUCTIONIn a flotation process, some of the minerals lifted up to the froth phase may drain back to the pulp due to various reasons such as weak attachment of particles to air bubbles, bursting of air bubbles, agitation of froth, etc. Weakly floating and entrained hydrophilic minerals drain at a faster rate than the strongly floating minerals, and effective exploitation of such differential drainage can lead to cleaner concentrates.For a given mineral, if the rate of flotation from pulp to froth is k1 (min·1) and the rate of drainage from froth to pulp is k2 (min""1), then the net (overall) flotation rate of the mineral, k (min-1 ), will be [Lynch et al., 1981 ]:"

Jan 1, 1997

In the late 1970's and early 1980's a considerable number of large scale open pit mines were developed in N.S.W. and Queensland. At the time these mines were planned, the industry was characterised by rising coal prices, rising fuel prices, and a host of other labour and government constraints different to the situation today. Yet some mines have clearly been able to cope with this change much better than others. While one mine may now be expanding and profitable, its neighbour may still be labouring under painful adjustment processes. This paper examines the major reasons for this difference. It suggests more robust criteria for assessment of future projects to reduce their sensitivity to changes outside management control.

Jan 1, 1990

COUNCIL OF ECONOMICS, AIME Formerly Mineral Economics Division Established as a Division December 15, 1948 Established as a Council February 26, 1957 Sheldon P Wimpfen, Chairman John D Ridge, Vice-Chairman (Mining) A J Philips, Vice-Chairman (Metals) Warren B Davis, Vice-Chairman (Petroleum) COUNCIL OF EDUCATION, AIME Formerly Mineral Industry Education Division Established as a Division January 15, 1932 Established as a Council February 26, 1957 James D Forrester, Chairman Charles V Kirkpatrick, Vice Chairman (and Chairman-elect) Lysle E Shaffer, Past Chairman Truman H Kuhn, Secretary-Treasurer Colorado School of Mines Golden, Colorado John S Bell, Contact AIME Director

Jan 1, 1960

By W L. Jennings

This paper summarises work undertaken to date as part of an investigation into the mineral resources of the proposedNorth West South Island National Park. The area covered by the proposed national park is underlain by many rock types that have undergone a long and complex history of evolution which has endowed it with some of the best potential for a wide range of different minerals in New Zealand. Many of these minerals occur only in this area or in Fiordland National Park.   The first gold-rush in the area occurred in 1856 and followed the discovery of payable gold at Lightbands Gully, south of Collingwood. The miners first focused on the alluvial deposits but soon shifted attention to lode potential. The total historical gold production for the area may be over 400 000 oz (NZ$250 - NZ$295.6 M at 1993 prices).   In addition to gold, a wide range of other minerals have been reported from the area including molybdenum, copper, nickel, zinc, silver, bismuth, stibnite, lead and antimony. The Onekaka iron-ore deposits have produced small tonnages of ochre and iron-ore at various times. Tungsten, platinoids and other metals have been. given only minor attention. The diverse geology of the Northwest Nelson has resulted in the occurrence of many industrial minerals which have been exploited in generally small-scale operations. Aggregate, chrysotile asbestos, clay, dolomite, marble, limestone, dimension stone, rip-rap, talc-magnesite and wollastonite have all been produced.

Jan 1, 1993

By Rajesh Minda

160 numbers of double bulb underreamed piles were constructed based on the safe loads specified in IS code at Tripura. The pile load tests yielded a much lower capacity. A detailed investigation work was carried out to find out the reasons for anomaly. The work included soil exploration followed by extraction of two piles bearing numbers 72 and 151. It was seen that the bulbs were not formed as per specification. Some comments on IS Code have been made at the end.

Jan 1, 1996

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By N. P. Mahumapelo

This paper is based on a study to determine the potential beneficiation opportunities for marble from Griekwastad in the Northern Cape Province. The marble was characterized mineralogically by X-ray diffraction. Major and trace elements were determined using inductively coupled plasma-optical emission spectroscopy. The sample was crushed, and the crushed material beneficiated by tumbling and polishing. The resulting beads were incorporated into a variety of jewellery and other decorative items. It is concluded that the beneficiation of Griekwastad marble presents a good opportunity for value addition and job creation, provided that an effective marketing strategy for the products can be developed..

Jan 1, 2014

By Louis W. Cope

Since its discovery, Cuba has been called the “Pearl of the Antilles.” The country remains that, albeit a little tarnished these days. In Havana, many of the buildings are being refurbished, while some new ones are under construction. Since 1991, the laws have been relaxed so that Cuba is developing a mixed economy of central control with free market. Joint venture agreements have been signed with businesses from many countries. This does not include the United States due to its embargo. But even these regulations have been relaxed some.

Jan 1, 2003

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

The theme of this Conference is 'The Future of Mining in New Zealand' to be addressed at a time of deepening economic concern. To ensure the assessment and development of our mineral resources in a competitive, safe and environmentally acceptable way a modest supply of a rare commodity û the professional mining engineer û must be assured. This paper briefly' reviews the history of mining education in New Zealand, discusses relevant overseas academic concerns and actions and discusses recent local trends which have led to a most serious recruitment position in the Department of Mining Engineering at the University of Auckland. Conclusions are drawn and proposals made which may remedy this situation which could have serious economic and sociological consequences for New Zealand.

Jan 1, 1991

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By Jim Richards, Eli Choueiry, Brett Robinson, Amanda Elioff

The Los Angeles Metro Gold Line Eastside Extension (MGLEE) extends Metro’s light rail system to the densely populated and growing East Los Angeles communities. Much of the 6 mile alignment consists of at-grade track, but the project also features a1.7 mile underground segment in cut-and-cover and twin-bored tunnel structures. In light of past experiences with open shield construction, The Metropolitan Transportation Authority (Metro) specified, for the first time, use of Pressure Face Tunnel Boring Machines (TBM’s) to advance tunnels through soft ground. This paper describes the history of the tunnel design, construction management, and construction methods adopted that resulted in successfully completing the tunneling segment.

Jan 1, 2007