Search Documents

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By Jerry F. Parola

In current practice, pile foundation design is based on a general under-standing of pile-soil interaction during installation and superstructure-pile-soil interaction after construction. The pile design is a reflection of experience, precedent and judgment for normal piling practice of working load capacities up to approximately 100 tons with corresponding ultimate capacities up to 200 tons. For higher capacity piles, pile design is even less predictable. In particular, the feasibility of pile installation is an important design consideration that must be given the proper attention. An installation capability that is not given the required emphasis can cause unnecessary problems.

Jan 1, 1986

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By U. B. Kodukula

Attempts are made to evaluate the feasibility of using a water-injection cyclone for the concentration of iron ore fines. The separation characteristics of clay fines, containing large amounts of alumina and silica, from the iron values are discussed. The effects of critical variables, such as injection water rate, truncated cone diameter, spigot opening and vortex finder diameter, on the performance of a water-injection cyclone in terms of iron, alumina and silica grades; iron recoveries; and alumina and silica rejections are discussed. A set of 16 full-factorial experiments (24) was carried out to gain an understanding of the individual and interaction effects of the variables. The results indicate that classifying iron ore fines containing 63.0% iron, 2.5% alumina and 3.5% silica through a water-injection cyclone can produce concentrates with iron grades greater than 66.0% and alumina and silica contents less than 1.5% and 2.0%, respectively, at different study conditions. The achievable iron recovery values are greater than 88%, and alumina and silica rejections are more than 80% and 50%, respectively, within the specific study conditions. While the truncated cone diameter, injection water rate and spigot diameter influences the alumina rejection to a considerable extent, it is mostly influenced by the vortex finder diameter. The iron recovery and silica rejection values are mostly influenced by spigot diameter and truncated cone diameter. The effect of injection water on the concentration characteristics depend on the prevalent truncated cone diameter and spigot diameter conditions.

Jan 1, 2008

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By J. A. Markovits

Coal has been hydrogenated in Germany on a lather extensive scale for the past 20 years, but the process is new to the United States. Although pressures up to 15,000 pounds per square inch have been employed on commercial scale in the synthesis of anhydrous ammonia, and there is evidence that valves, tubing, and equipment have been developed recently up to 30,000 p.s.i. working pressure at moderately elevated temperatures for limited industrial production of plastics, such pressure ranges are unusual in American industry, and equipment designed for them is not commonly available. In the Coal Hydrogenation Demonstration Plant at Louisiana, Mo., 10,000 p.s.i. operating pressures are combined with temperatures up to 1,000° F., and the materials to be processed under these conditions range from gases to mixtures of viscous liquids containing high percentages of abrasive solid particles. These service conditions presented unusual engineering problems requiring thorough investigation, Limited financial resources arid rigid time schedules inherent in the synthetic liquid fuels act often forced decisions before the best answer to a problem could be developed. Sometimes the ideal technical solution proved to be beyond the financial limitations of the demonstration-plant program.

Jan 1, 1949

By Ware AR, Doyle BJ, Hoogvliet H

The Ladolam deposit lies within the altered volcanic rocks of the caldera floor, part of which now forms Luise Harbour. It was discovered in 1982 in the course of a reconnaissance drainage sediment sampling programme. This was designed to follow up indications of surface hydrothermal activity noted by Government geologists during an earlier survey of the Tabar-Feni island chain. Diamond drilling began in September 1983 and by the end of 1989 a payable and proved mineable reserve containing 19 million ounces of gold had been established. Rock types and structures are masked at the surface by intense alteration and weathering. An extensive drilling programme has enabled the identification of these features and the relationships between them necessary for an understanding of the factors controlling gold mineralisation. It has also led to the recognition of two distinct phases of alteration. The first phase of porphyry-style potassic alteration was followed by violent caldera formation, producing extensive brecciation and veining. The second alteration phase partly over- printed the first phase and was an epithermal one, evidenced by argillic, advanced argillic and phyllic assemblages. During this event, a large volume of fluids circulated under the favourable structural conditions; these fluids included a sulphur- rich, neutral chloride brine believed to have transported the gold. Boiling and mixing of circulating fluids in the open breccias is thought to have resulted in deposition of the gold. There is evidence that this process is continuing at the present day.

Jan 1, 1991

Effect of Lattice Impurities on Electronic Properties and Surface Adsorption of Sphalerite - A Density-Functional Theory Study

Sep 13, 2010

The notes from which this paper has been prepared were set down at the time of the author's departure from Australia in 1935. Mr. Frank Forman, Government Geologist of Western Australia, who has very kindly read the paper in manuscript, affirms that the views here set forth are now accepted by most geologists. Thus, Forman's recent presidential address before the Royal Society of Western Australia (1937) mentions sediments in the Kalgoorlie Series "including banded jaspers and jaspilites."While it may, therefore, be superfluous to belabour the question further at this time, Mr. Forman has encouraged the author to publish this paper as a summary or both past and present views.To those specially interested in the subject of the paper, a study of pertinent Plates attached to Western Australian Geological Survey Bulletin No. 71, 1917, is suggested.The type of rock which is variously called "jasper bar," jaspilite, or "ferruginous quartzite" is familiar to all mining men who have worked in the West Australian goldfields.In its typical form it is a "striped" rock consisting of alternate layers of white or pinkish silica with red to brown bands of iron-bearing silica.In the course of geological work in many parts of Western Australia I studied exposures of jasper bar and was repeatedly impressed with the similarity of much of the material to the sedimentary "banded iron formation" of Canada. It was, therefore, a surprise to learn that the jasper bars were not generally regarded in Australia as sedimentary horizons. It is true that Honman offered convincing evidence of the sedimentary origin of the jaspers...

Jan 1, 1939

By T. P. Mucho

Strata behavior and support performance were evaluated in a longwall tailgate test area at the Eagle Nest Mine near Van, WV. The mine operates in the Eagle coalbed which ranges in height from 4 to 6 ft (1.2 to 1.8 m) on the mine property. Rugged topography results in rapid changes in overburden which ranges from 200 to 1200 ft (61 to 366 m). The immediate roof at this mine transitions from sandstone to shale. In some areas the sandstone appears to be massive while in many locations it is highly laminated, fossilized, and interspersed with coal streaks. Horizontal stress levels appear to be sufficient to create instabilities in the roof in some locations, especially where the roof is thinly laminated. Traditionally, hardwood cribs have been used at the mine to provide secondary support for longwall tailgates; Strata Products' Hercules cribs are installed on 8 ft (2.4 m) centers staggered left and right in the tailgate entry. In a 250 ft (75 m) tailgate test area, however, cable bolts were installed in lieu of cribs. The bolts were 12 ft (3.6 m) long tensionable cables anchored with 5 ft (1.5 m) of resin. Four cables were installed across the entry and rows were spaced on 6 ft (1.8 m) centers. Primary roof support was maintained in the vicinity of the test area using 42 in (1.1 m), grade 60, No. 6 (19 mm diameter) resin bolts installed on 4 ft (1.2 m) centers through T-2 channels. The cable test area was located under a stream valley in an area of relatively shallow overburden. Strata instabilities consistently had been associated with the stream valley in both the Eagle and the overlying Powellton coalbeds. In an effort to further expose the cables to the most difficult stress conditions available at the time of the test, the specific site chosen was directly beneath a barrier pillar remaining in the upper Powellton mine (approximately 150 ft (45 m) of interburden separates the two coalbeds).

Jan 1, 1996

Exerting the Advantages of National Key Discipline, Outstanding the Training of Engineering Capability, Cultivating Talent to be with Innovation Ability

Sep 13, 2010

By C. L. Kosmoski

The mining industry faces many workplace hazards that are a threat to human health and safety. The Bureau of Labor Statistics has found that employees in coal mining are more likely to be killed or sustain an injury or illness than workers in private industry. These injuries are also likely to be more severe (Bureau of Labor Statistics, 2007). In recent years, coal mining injuries have attained national attention due to highly publicized disasters. Despite these threats to worker safety and health, the U.S. relies on the mining of coal to meet its need for electrical power, with42% of electricity in the U.S. generated through the burning of coal (U.S. Energy Information Administration, 2012b; United Mine Workers of America, n.d.). Furthermore, the production of coal continues to increase and reach record levels every year(National Mining Association, 2012; U.S. Energy Information Administration, 2012a). For this reason, the coal mining industry must continue to find ways to protect its workers while maintaining productivity. One potential approach to protecting workers while maintaining productivity is through improving the safety culture at coal mines. In order to achieve this culture, operators, employees, the inspectorate, etc. must share a fundamental commitment to safety as a value. This type of culture is known in other industries as a ?safety culture? and can be defined as the characteristics of the work environment, such as the norms, rules, and common understandings that influence facility personnel?s perceptions of the importance that the organization places on safety. Fundamental to improving safety culture within an organization is understanding the existing safety culture; improvements cannot be made without first elucidating areas that require improvement. This manuscript details the process undertaken by researchers at the National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) to assess the safety culture at five underground coal mines across the United States. The purpose of this manuscript is to introduce the mining industry to a multi-methodological approach to safety culture assessments. Further, it is the goal of this manuscript to highlight the value of including both quantitative and qualitative methods into safety culture assessments in order to obtain the most comprehensive view of an organization?s safety culture. Because this manuscript focuses solely on the methodology implemented, data and results obtained during the five safety culture assessments will not be presented in this manuscript, but will appear in a future publication.

Feb 27, 2013

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By Jorge Oviedo

La planta de lixiviación, extracción por solventes y electrodeposición (L-SX-EW) de Southern Perú es una operación hidrometalúrgica dedicada a la lixiviación ácido – bacteriana de los botaderos de mineral de baja ley de la Mina Toquepala, para la producción de cobre catódico de la más alta pureza. En ese sentido, el presente trabajo describe la evolución del sistema de control y supervisión de esta planta minera en Cuajone. Para ello, dicha planta debe tener una actualización constante de sus sistemas de control y ser capaz de cambiar con la velocidad a la que avanza la tecnología de Control de Procesos. Asimismo, debe contar con personal calificado que permita el desarrollo y modernización de los sistemas sea continuo y no dependa solo de expansiones y ampliaciones ejecutadas por especialistas externos. De forma que este software de supervisión, no solamente considera la capacidad de operar la planta, si no debe ser una ayuda tanto para el operador como para brindar información en la correcta toma de decisiones.

Aug 25, 2002

Your thoughts on the current status of the global minerals industries? The global economic, technological, social and political changes of the last two decades of the 20th century resulted in the emergence of a restructured minerals industry. This industry is now based on a new cost-cutting philosophy; utilization of modern technology; productivity gains rather than production tonnages; diversification of mineral markets; and globalization of exploration, mining and processing. Quantity and tons used to be the focus. The emphasis today is on remaining competitive in the marketplace by lowering per-unit production costs as much as possible. What factors and trends will impact the minerals industries in this, the 21st century? A number of parameters will impact minerals operations and shape the future sustainability and growth of the minerals industries. Increased demand for minerals will be accompanied by the demand for technical advancements. We will also see a continued emphasis on health and safety, environmental stewardship, and education and training. Let me elaborate.

Jan 1, 2002

A combined reflection seismic and magnetic survey off the south coast of New South Wales has revealed six distinct reflection horizons within the Lower Triassic-Upper Permian sequence, and has enabled the upper part of the lllawarra Coal Measures to be mapped in considerable detail. Large magnetic anomalies in the eastern half of the survey area appear to originate in the Gerringong Volcanic Sequence which forms the magnetic basement in the survey. Small residual anomalies in the western half of the area can be correlated with small scale faulting and folding in the upper part of the llawarra Coal Measures, as revealed by the seismic reflection survey.A synclinal axis striking at approximately 55° has been mapped near the western margin of the survey area, and areas of faulting and folding have been outlined by combined analysis of seismic and magnetic results.

Jan 1, 1970

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997