Search Documents

By Murali Gadde

Numerical simulation of cutter roof failure is a daunting coal mine excavation design issue. The complex progressive failure mechanisms associated with cutter failures are extremely difficult to replicate in computer models. However, this paper shows that with a proper selection of constitute behavior and implementation of cutting sequence, it is possible to realistically reproduce cutter failure using continuum models. Strain-softening material behavior and a systematic step-by-step model solving for a four-entry-and- three-crosscut model produced results that are similar to cutter patterns noticed in field. These results show that traditional modeling with geometries created in one model-step has limited applicability and may even provide misleading conclusions under some circumstances. Most importantly, the proposed modeling methodology provided some insights into the reasons for the inconsistent spatial distribution of cutters often noticed in coal mines. The modeling also revealed the usefulness of cutter mapping to determine the directions of in situ horizontal stresses.

Jan 1, 2005

By Shengli Yang

Solid backfill mining, as a green mining technology, has the advantages of a higher resource recovery, less damage to the environment and the ability to dispose of waste underground. It has been applied successfully in the Xingtai and Xinwen mining areas in China. Strata behavior and the movement of overburden strata in this mining method are very different from fully mechanized longwall mining, which results in a natural caving, because the gob is filled with waste rock, fly ash and other backfill material. The results of field measurements showed that the periodic weighting interval of the main roof is longer; the magnitude of periodic weighting is smaller; the peak and zone of influence of the front abutment pressure are smaller than those in fully mechanized mining; that major deformation of mine roadways occurs within the influence zones of the abutment pressures; that the falling space of immediate roof is smaller, with the lower portion falling more sufficiently than the upper; that the main roof subsides slowly; and that the falling height of the overlying strata is greatly reduced.

Jan 1, 2011

By Anthony Lannacchione

There has been a persistent need to forecast roof falls so that miner's exposure to hazardous underground environments can be minimized. Several monitoring techniques have been developed and are used today with varying levels of acceptance in the mining industry. This paper examines the potential for monitoring microseismic emissions activity as a means of forecasting roof falls. The use of this activity to forecast roof falls has drawn only limited attention, resulting in a lack of published field performance data. This deficiency is being partially addressed by analyzing data obtained during longwall mining at Moonee Colliery in 1998. The Moonee data base contains a wealth of information concerning roof fall forecast parameters and the seismic alarm criteria used to develop these forecasts. Four seismic alarm criteria were developed and used by Moonee with varying degrees of success. Roof falls were forecasted 73% of the time with average forecast times of 54 minutes. Ninety percent of the predicted roof falls had a warning time, i.e., the time between warning and roof fall event, of greater than 1 minute. The fraction of forecasted roof falls decayed logarithmically as a function of warning time, until only 20% of events were predicted more than 100 minutes prior to roof falls. False alarms occurred in 50% of the warnings. Many of the false alarms were quickly followed by a cessation in mining which could have temporarily halted the on-going failure process. If mining had continued immediately after the false alarms, a roof fall may have occurred soon after. The microseismic activity collected .from Moonee Colliery demonstrates that techniques to forecast roof rock instabilities in underground mines are possible.

Jan 1, 2005

By Graham Daws

The introduction of UK rock bolting technology has been applied in many large underground coal mines around the world. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to introduce rock bolting to a mine.

Jan 1, 2011

By William B. Beerbower

When full length resin grouted bolts were introduced into U. S. coal mines some 11 years ago, it was assumed that safety would be the primary benefit. There is ample testimony to substantiate the safety factor as an important reason for using resin roof bolts. More recently, it has been determined that many coal operators not only concur with the safety consideration but also benefit economically from the safer working conditions resulting from a reduction in roof falls. IMPROVED SAFETY Some typical roof fall reduction experiences with resin bolting follow: ? Western Kentucky Mine - Resin bolting reduced roof falls by 80%. ? Southern West Virginia Mine - Experienced 141 roof falls between 1971 and 1972. In 1973 with resin bolting, roof falls were reduced 85%. ? Western Pennsylvania Mine - In 1973 had 59 roof falls with mechanical bolts. During the same period of 1974 with resin, only 19 falls were experienced - a reduction of 66%. The overall experience with resin bolted roof support has been an average 50% reduction in roof falls. Long term, this can translate into improved worker morale. As a matter of fact, a general mine foreman at the same Southern West Virginia mine mentioned above commented that improved miner morale was noticeable following the introduction of resin bolting. HOW GREATER SAFETY CAN BE COMBINED WITH INCREASED PRODUCTIVITY IN COAL MINING OPERATIONS Experience has also shown that a reduction of roof falls with resin bolting has resulted in increased production for many coal operators. Some typical examples with mines using resin bolting follow: ? Western Kentucky Mine - Resin bolting contributed to increasing production from 7000 to 11,000 tons per day, due to a 80% reduction in roof falls. This was accomplished in part by a reduction of 50% in timbering requirements and the reassignment of three roof fall cleanup crews to coal production. ? Pennsylvania Mine - Following resin bolting introduction the section showed a 50% increase in production. ? Central West Virginia Mine - Continuous miner production averaged 6 cuts per unit shift prior to resin bolting. Reduction of cleanup time, resulting from improved roof support with resin bolting, increased production to an average of 9 cuts per unit shift. PROPERTIES OF RESIN BOLTING SYSTEMS Several of the important properties of resin bolting systems which contribute to its improved performance are listed below: ? Full length anchored resin bolts and many resin anchored, point anchored bolts provide effective resistance to changing rock strata stresses throughout their length, thereby improving stabilization of rock strata over long periods of time. ? Individual layers of rock are anchored into a single high strength beam providing excellent resistance to vertical and lateral strata movement, the most common cause of roof failure. ? Moisture cannot corrode the fully grouted bolt. ? Has twice the pull strength of mechanical bolts (See Figure 1)

Jan 1, 1982

By Erik Westman, Benjamin Mirabile

"Quantitative evaluation of secondary support performance in longwall tailgates in U.S. coal mines was introduced with the U.S. Bureau of Mines (USBM) Wood Crib Performance Model. This model evaluated crib performance based on load capacity, stability, and convergence characteristics. The introduction of a large variety of alternative secondary supports in the 1990s prompted a full-scale load-displacement testing program conducted by the USBM and, subsequently, NIOSH. The application of the ground response curve concept to secondary supports provided a more complete estimation of secondary support loading in longwall abutment zones. Secondary support loading from floor heave, horizontal stress effects, and pillar yield are captured by the ground response curve. A point on the ground response curve can be measured by instrumenting a secondary support with load and convergence measurement devices. A segment of the ground response curve can be measured by instrumenting two secondary support types of varying stiffness. Numerical models have been used to construct complete ground response curves for longwall tailgates based on measured secondary support performance. The ground response curve concept can be used as a design methodology for secondary supports in the #2 entry, as well as the longwall tailgate. Extending published evaluation and design methodologies for secondary support in longwall tailgates, a ground response curve unique to the loading conditions and required functionality of the #2 entry can be developed. Numerical models can be used to construct full ground response curves based on measured data in the #2 entry.INTRODUCTIONA longwall ventilation system is designed to continuously dilute and move methane-air mixtures and other contaminants from the active face, to bleeder systems, and out of the mine. The #2 entry of the tailgate gateroad serves to transport contaminated air from the longwall face to the bleeder system. The #2 entry is required to function as an air course between two longwall gobs and is subject to significant ground movement and loading. Current ground support design and evaluation practices are based on empirical evidence and little to no quantitative data on support performance exists for these entries. Substantial volumes of research have been conducted on ground movement and support performance in longwall tailgate entries. Following the successful ground support evaluation and design practices established for longwall tailgate entries, a practical and efficient design methodology can be adapted for supporting the #2 entry of a three-entry gateroad system."

Jan 1, 2018

By Charlie Li

A cut-and-fill mine stope, located at a depth of about 1000 m in a lead-and-zinc mine, was closed down because of large roof convergence and fractures appearing on the hanging wall. The instability problem was owing to the relatively low strength of the rock subjected to high in-situ stresses. Extra reinforcement was required to secure the stope so that the remaining ores in the stope could be mined. Assessment of the fracture mode in the country rock surrounding the stope was carried out and then the reinforcement de- sign was worked out. It was proposed that the unstable section of the stope would be reinforced by bolt-shotcrete ribs as well as selective long bolts. The philosophy of the design was to hold up the fractured country rock by bolts and shotcrete so that a load-bearing arch could be formed in the roof and in the hanging wall. Six shot- Crete ribs were set up in the unstable section of the stope. Displacement measurements showed that the roof convergence reduced from about 2 &day to the ordinary creeping level, about 0.25 &day, immediately after the reinforcement operation. Six month later, the hanging wall collapsed into the stope in a place just outside the reinforced section, which indirectly proved the effectiveness of the bolt-shotcrete ribs in reinforcing the fractured country rock. This case showed that an appropriate rock mechanics assessment would form a solid base for reinforcement/support design. It also provided an evidence for the philosophy of the reinforcement by bolt-shotcrete ribs - establish a load-bearing arch in the rock.

Jan 1, 2005

By D. Newman

The objective of this is paper is to review the current state of knowledge and practice in highwall mining (HWM). HWM has become a standard method in surface mining, commonly used alone or in conjunction with contour or slot mining. It provides 800-feet to 1,200-feet of additional recovery when the economic stripping ratio is reached in contour mining or in slot mining when surface access to a reserve is limited. A significant attribute of the highwall miner is its versatility. HWM has been used successfully to mine abandoned pre-reclamation law highwalls, points or ridges uneconomic to mine by underground or other surface methods, outcrop barriers left adjacent to underground mines, separate benches of the same seam where the parting thickness or quality differences between benches render complete extraction uneconomic, previously augered areas containing otherwise inaccessible additional reserves and close or widely spaced multiple seams. The theory and design methods to assess roof; pillar, and floor stability are presented followed by three case histories. Simple design charts for sizing HWM web and barrier pillars are also presented. A recommended web pillar width may be obtained from the design charts given the overburden depth, the HWM cut width, and the mining height. Given the depth and panel width for a set of HWM cuts, another set of charts gives a suggested barrier pillar width. The case histories, hm Northern and Southern Appalachia are used to illustrate the application of rock mechanics to quantify the stability of the highwall, roof, web pillars, and floor. The case histories involve 1) mining through a previously augered highwall, 2) mining under back-stacked spoil and 3) selective mining of closely spaced benches of the same seam. Because each site is unique, the appropriate pre-mining geotechnical analyses range from the calculation of roof, web pillar, and floor bearing capacity stability factors to detailed numerical modeling of the auger and underground mine workings. When operating in the vicinity of existing underground mine or auger workings, the determination of ground deformation and strains resulting from highwall mining is a necessary facet of a ground control investigation.

Jan 1, 2005

By Gregory J. Chekan

Developing a coal seam that has been influenced by previous mining in seams either above or below can result in severe ground control problems. In many instances, interactions between operations are inevitable. but improvements in ground stability can usually be achieved by-predicting potential problem areas in advance and adjusting the mining plans accordingly. This report investigates four case studies involving interactions between operations that used both room-and-pillar and longwall mining methods. In each case, geologic and mine design parameters are addressed, and those parameters found critical to the interaction are further defined in relation to observed ground problems.

Jan 1, 1990

By Greg Hendon

Longwall developments in the UK have historically consisted of single entry gate roads. Adjacent developments were separated from existing panels by large barrier pillars (designed of sufficient width to get away from the longwall abutments of the previous panel) or by small barriers driven in the shadow, or de-stressed zone, of the previous panel. Some 2nd panel tailgates were also driven skin to skin leaving no coal barrier between the newly driven entry and the heavily supported existing gateroad. With the developement and wide acceptance of fully bolted entries and the pressure to reduce production costs, alternatives to single entry drivage, particularly yield pillar developments, were examined. Through the Rock Mechanics Branch of British Coal, a cooperative study was begun with Jim Walter Resources, Inc., USA, (JWR) to look at the yield pillar alternative in detail. This study was to determine the feasibility of utilizing yield pillars in the UK and to determine, through monitoring, the possibility of reducing stable pillar widths at JWR. The study has included extensive monitoring of the yield-stable-yield pillar system at JWR No. 7 Mine and an underground trial of a two entry yield pillar test area at Welbeck Colliery in the UK. This paper describes results from the JWR study and the subsequent results of the first advancing yield pillar development in the UK at Welbeck Colliery.

Jan 1, 1995

By Daniel W. H. Su

This paper presents the results of an extensive geomechanical testing and monitoring program conducted at a longwall panel. The field program included the monitoring of roof caving sequence and mechanism, surface subsidence, change of pillar stress, roof displacement and entry convergence, and strength characterization of the overburden rocks. The response of eight headgate pillars and the adjacent entries was monitored as the longwall face approached and passed the instrumented locations. Overburden response to longwall mining was monitored using time domain reflectometry (TDR) technology; and, the height of the highly fractured zone above the gob was determined by postmining drilling. Good correlation was found between the height of the highly-fractured zone and the TDR, subsidence, and pillar stress data. The results provide a detailed picture of the response of overburden strata and chain pillars to longwall mining. A preliminary model representing the overburden strata behavior at the test site in response to the longwall mining is proposed.

Jan 1, 1987

By Daniel W. H. Su

A floor-bearing capacity test apparatus was designed and constructed to determine the true bearing capacity of soft floor materials beneath coal pillars or longwall face supports. The apparatus has been employed in entries up to eleven feet in height. Results of in-mine floor-bearing capacity tests suggested that the ratio of the soft fireclay thickness to the bearing plate width and the moisture content in the fireclay were the most critical parameters affecting the ultimate bearing capacity. Foundation engineering principles were applied to interpret the field test results to estimate the floor-bearing capacity beneath longwall face supports.

Jan 1, 1993

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By Liang Yin-Huai

In Fuxin Coal Mines, there are more than 20 million tons of coal buried under seasonal streams. The coal seams are mostly shallow. We have mined more then 50 mining blocks distributed in 5 coal mines. Their natural conditions are different, and the consequences are also more or less different. However, no stream-water-inrush accidents under regular mining conditions are the same. There were 3 exceptions. They were caused by unexpected roof caving which made valleys or alluvia subside as funnel-like cavities and let in inrush of stream flow. The key to our success in mining shallow under-stream coal seams, according to our analysis, is that valleys or alluvia subside gently and basically evenly with contractible tension fissures and that fissures both in valleys or alluvia and in rock seams are blocked up or sealed by cohesive deposits either from alluvia or rock. This paper treats: (1) some typical illustrations of mining shallow coal seams of different occurrences under streams of different sizes, flowing capacities and valley structures, (2) observations of the height of caved and fissured zones and subsidence of valleys or alluvia, (3) observations of underground water flow before, during, and after mining and the fluctuation with respect to stream flow, (4) observations and analyses of blocking up of fissures caused by mining, and (5) feasibility of mining shallow under-river coal seams.

Jan 1, 1990

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms around a longwall gate-road system in an underground coal mine. Of particular interest was roof deformation over the headgate entry. The strata above and below the coal seam are very weak, carbonaceous mudstones that have planes of weakness oriented along the bedding. Visual observations of previous gate roads over several years suggested that deformation was time dependent and resulted in creep along joints or crack growth. Instruments were installed at a test site to measure deformation around the entry, strew changes in the pillar, and loads transferred to support systems. Multipoint extensometers, instrumented bolts, instrumented trusses, biaxial stressmeters, borehole pressure cells, and single-point extensometers were installed. Monitoring continued until the longwall face passed the test site by 38.7 m (127 ft). Results show that fracture zones arched over the entry from both ribs, most bolts and trusses were loaded past their yield point, and the largest change in secondary principal stress was almost horizontal in the pillar. Displacement measurements in the roof showed classic primary creep.

Jan 1, 1995

By M. E. Duncan Fama

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface modelling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model predicted the fender would suffer considerably more deformation and strain.

Jan 1, 1992

By Russell Frith

The paper defines the various operational advantages associated with the use of cribless tailgates during longwall extraction and considers the associated ground control issues that need evaluating to ensure a successful outcome. Reference is made to longwall mines in Australia currently using cribless tailgates and the geotechnical and ground support factors that allow them to do so This includes the nature and behaviour of the roadway roof the stability of the chain pillar and also the type and timing of installed support A specific case history from a colliery in NSW will he referred to whereby heavy standing support was replaced with lower density tensioned cables as routine TV secondary support, which resulted in both improved TG roof conditions and a significant cost reduction. The conclusion will be drawn that cribless tailgate roadways can potentially he used in many environments either due to the existence of highly competent immediate roof conditions or through the appropriate application of active reinforcing support measures in less competent conditions. Use will he made of Strata Engineering?s roof behaviour and stability model in demonstrating the various concepts involved.

Jan 1, 2000

By Chris Adams

The application of pre-tensioned tendon roof support assisted Harworth Colliery in their revival, from impending closure to lowest cost deep-mined producer in the UK, over just six months last year. The paper describes this success story, how it came about, the reasons "why", and the method "how"

Jan 1, 2003

By Ian W. Farmer

A description of the factors causing outbursts and rockbursts in coal mines is given. The mechanics of both outbursts and rockbursts can be described in terms of conversion of stored strain energy in the coal and surrounding rocks into kinetic energy through failure. The major difference between the two phenomena is that gases adsorbed onto the coal structure and desorbed during deformation contribute to the energy available during outbursts and may also affect the loading and unloading characteristics associated with failure. The amount of energy involved and the type of phenomenon are related principally to gas content depth and rock behavior.

Jan 1, 1988

By George J. Karabin

Since the inception of a qualitative pressure arch theory by Haak4 in 1911, much work has been done in an effort to apply this concept to underground mining. It has been used in both longwall and room and pillar mining to determine roadway and pillar stability (with varying degrees of success). This paper presents a summary of a case study where the pressure arch concept was extended in a totally qualitative manner to define the source of roof control problems in the mains of a Pennsylvania mine. It was concluded that, due to the method of mining employed, a pressure arch formed over a portion of the entries, and the high abutment stresses accompanying it resulted in extreme roof deterioration. The following discussion will include a general presentation of the arching mechanism, the physical response of the roof strata under mining-induced abutment stresses (both from the case study and in general), a computer simulation of ground stability under both "normal" and "abutment" stress conditions, and finally, potential means of alleviating such conditions.

Jan 1, 1982