Search Documents

By Milton Syamujulu

In 1994, Nkana smelter commissioned a Multimillion US$ Dollar Chilean Teniente converter (CT) in its operations in order to improve its smelting technological base. The main objective was to reduce the overall smelting energy costs and increase the sulfur capture for sulphuric acid production to support the company?s leaching operations at Nchanga Tailings Leach Plant. A decade of CT operations have since ensured following its installation and startup. This paper provides a Technical and Operational Audit of the performance of the CT in the first 10 years of its operations at Nkana smelter.

Jan 1, 2005

By P. H. Botha

An account is given of the procedures used by the South African Iron and Steel Industrial Corporation (Iscor) for tests on the flotation of coal fines, and some of the beneficiation problems encountered with coal from Durnacol, Grootegeluk, and the Soutpansberg area are discussed. These, and other South African coals differ from overseas coals in that they contain a high percentage of fixed ash, which means that they have to be crushed more finely for liberation and that they then contain more fine material (smaller than 0,84 mm). In addition, the coal from the three areas mentioned occurs in fine layers and seams, and contains many intergrown particles.

Jan 1, 1980

By L. A. Vermeulen, D. D. Howat

The use of pebbles as the medium in the grinding of quartz gravel in a laboratory mil provided experimental data that were used to quantify the relationships between the feed rate of ore to the mil, the fineness of grind of the product, and the wear rate and consumption of the grinding medium. Fineness of grind is expressed as the inverse of the harmonic mean size, a quantity that is calculated from data obtained by sieve analyses. The commonly used criterion for fineness of grind (the percentage of material smaller than 75 µm in the mil product) is shown to corelate approximately linearly with the inverse of the harmonic mean size. An increase in the feed rate was found to cause the harmonic mean size of the product to increase linearly, Le. the relationship previously found for metalic grinding media is applicable to al grinding media, irespective of shape or composition. Simple expressions for the consumption and wear rate of pebbles are derived from the experimental data, and are shown to be functions of the feed rate. The expression for wear rate is a monotonicaly increasing function, while that for consumption is a hyperbolicaly decreasing function of the feed rate. In contrast, a linear relationship was found between the rate of wear of the grinding medium and the rate production of fines. The expressions that were previously developed in relation to the use of metalic grinding media are shown to be equally applicable to pebble milling.

Jan 1, 1988

By Northrop. I. N.

Hardmetals possess extremely high hardness and wear resistance, which render them ideal for applications such as metal-cutting tools, rock-drilling tools, and industrial wear-resistant parts like dies, punches, and seals. However, hardmetals are britle, and show poor resistance to impact and shock. They can therefore rarely be used unsupported, and it is common practice to attach hard metal working parts to a more resilient tool holder or support, which is normally made of steel. . . . Owing to the widely differing physical and mechanical properties of steels and hard metals, the Joining of one to the other is problematic, and the method used must be chosen with care. This paper reviews several methods available for the joining of hardmetal to steel, and discusses the advantages and disadvantages of each.

Jan 1, 1987

By C. Van Rhee

In dredging practice sand is eroded at very high flow velocities using water jets. The existing pick-up functions overestimate erosion. By taking the permeability into account conventional pick-up functions can be made suitable for high velocity erosion. This can be achieved by modifying the critical Shields parameter. The procedure is demonstrated using the pick-up function of Van Rijn. The theory is compared with experiments and agreement is good.

Jan 1, 2007

By J. A. Voster

Premier Mine (a part of De Beers Consolidated Mines Ltd) which is situated 38 km to the east of Pretoria, has the largest known diamond pipe in South Africa. The mine started operations in1903. The Premier Mine kimberlite pipe is unique in that it is intersected by a 75 m thick gabbro sill at a depth of 400 m below surface. The current mining method used is mechanized panel retreat caving, which has been successfully used to extract ore from the different mining blocks. All caving at Premier Mine is below the sill and failure to exercise good draw control could cause the early ingress of gabbro waste. Draw control at Premier Mine is crucial as it aids in preventing conditions of isolated draw, which results in the early ingress of waste, compaction of the kimberlite and the loss of ore reserves. To assist, an underground vehicle monitoring and control (VMAC) system was installed to enable the effective management of the draw control function. The system has evolved graduallyin collaboration with a local developer. The data accumulated is used to decide the most effectivedraw point loading pattern in order to achieve sound draw control principles. This is achieved as each load can be related back to the draw point of origin. The VMAC data recorded also relates back to specific load-haul-dumps (LHDs), tunnels, ore passes, as well as indications of dates, times and payloads recorded. An interface exists between the VMAC and a draw control linear program. Premier Mine’s VMAC system is not a ‘dispatch’ system but rather a draw control system that caters for Premier Mine’s specific block cave requirements. Premier Mine has realized that successful automation is not dependent on technology alone but rather on the successful implementation thereof.

Sep 1, 2001

By R. B. MacGillivray

The No. 2 Seam at Van Dyks Drift Colliery was found to be made up of six easily recognizable bands or plies of differing qualities. Not only did the plies differ from one another in quality, but their thickness and quality varied laterally across the mine. The economic production of a Iow-ash blendcoking coal for supply to the Japanese Steel Mills called for the mining of different portions of the seam. The portions that could be extracted economically varied in thickness and position within the No. 2 Seam across the mine. A unique system of selective mining had to be developed involving the dispatch of two separate streams of coal out of the mine. Conventional American mechanized pillarand-stall mining was used, and the productivity was improved by the installation of twin conveyor belts into a double-header section. The method of grade control that was instituted to ensure efficient extraction of the available coal reserves is described.

Jan 1, 1985

By R. A. Snodgrass

Heap leaching is a topic that is gradually generating more interest in South Africa as more non-Witwatersrand gold deposits are being investigated. This was evident from the number of delegates (85) who supported the SAIMM School on Heap Leaching, which was held at Mintek from 29th February to 3rd March, 1988.

Jan 1, 1988

By S. Budavari

On the one-hundredth anniversary of the founding of the South African School of Mines, this paper presents a historical review of the tertiary mining education carried out by the School of Mines in Kimberley and the subsequent institutions in Johannesburg. In addition to recording and evaluating a century of mining education, it describes the current activities of the Department of Mining Engineering at the University of the Witwatersrand, which is believed to be the natural successor to the School of Mines. The comparison of earlier and contemporary academic mining activities reflects a gradual transition from the educational philosophy and objectives of a school of mines to those of a modem university department. In the conclusions, some aspects of the educational effort expended during the past hundred years are briefly highlighted.

Jan 1, 1996

By A. A. Snodgaass

This paper reviews lead as a commodity, starting with a brief historical outline and dealing with the various uses of lead in some detail. It then goes on to discuss some statistics in relation to the production and reserves of lead, before sketching its mode of occurence. The topics are approached in regard both to the world and to South Africa, with the emphasis on the later. The mining and concentration of lead at Black Mountain Mine at Aggeneys in the north-western Cape Province are detailed, before a general account is given of the smelting, hydrometalurgical extraction, and refining of lead, together with the processes used in these activities. The paper concludes with a discussion of safety and health in regard to lead and a brief look at the commodity's future.

Jan 1, 1986

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By T. A. Silva, A. C. Bragança

Lime has been added to the iron ore slurry transported by the Samarco pipeline since its operation start-up in 1977.Initially, internal corrosion was the main concern therefore the reagent was used only for pH correction. Over the last ten years, though, transport of more complex slurries demanded a significantly higher dosage of lime to guarantee adequate rheology control. Several other reagents have been tested for the same purpose yet none has proven to be as effective regarding technical performance, environmental impact and cost. However, an alternative was sought so that the slurry rheology could still be controlled in case lime addition became impracticable. The objective of this paper is to present a technical solution for this matter, which takes into account environmental aspects. It consists of adding soda for pH correction and an organic coagulant as a rheology modifier. The latter is a quaternary ammonium salt which affected the slurry transport properties in the same manner as lime when tested in a laboratory. It showed no plug formation and allowed solid particles to settle, forming a loose sediment after rest. These results indicate a low probability of plug occurrence in the pipeline and the formation of a readily reslurryable sediment upon shutdown of the pumping system. Industrial tests should be performed in order to validate the laboratory results.

Jan 1, 2007

By C. O. Beale

This paper is the first part of a two-part review on the subject. , , .. Here reference is made to the place of copper among the elements, Its properties, Its historical significance, and its 'end uses both in general and in South Africa. Its current market situation and its prospects are dealt with briefly. Some account is then given of the mining and metallurgical techniques employed. in South Africa in the production of copper, together with the names of the companies at present Involved and brief descriptions of their operations, ,... . .. The operations of these companies are described In greater detail In Part 11(Apn11985 Issue of the Journal).

Jan 1, 1985

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

GENERAL Invitation to attend O.F.S. Branch Meeting: Members of the Witbank/Middelburg Branch were invited to attend a branch meeting of the O.F.S. Branch on the 15th November. The subject of the meeting would be a talk on the Hendrik Verwoerd Dam Project and up to 25 members could be accommodated on the nights of the 14th and 15th November by kind invitation of members of the O.F.S. Branch. A questionnaire would be issued at a later date, to obtain the names of those interested in attending the meeting. PAPER FOR PRESENTATION The Chairman called upon Mr G. H. J. Kitson to present his joint paper, entitled: 'Photoelectric readings; their significance for dust control on collieries.' G. H. J. Kitson (Member) and Y. J. F. Haven (Visitor). After Mr Kitson had presented his paper, both he and Mr Haven answered questions from the floor. The Chairman then thanked Mr G. H. J. Kitson for presenting the paper, and the meeting closed at 6.15 p.m.

By S. K. Kawatra

Feasibility studies of the on-stream analysis of lead in mineral slurries by S. K. KAWATRA. P. Eng. (Canada). Ph.D. (Australia). M.Sc. (India) (Visitor) Instruments for the measurement of lead in mineral slurries by the use of isotopes can be based on the absorption of Iow-energy gamma rays, backscattering of beta particles, or X-ray fluorescence. The merits of each method are discussed, and the reasons for the selection of the beta-backscattering technique are given. A system using this technique has been designed, constructed, and tested on samples of concentrates from an industrial concentrator.

Jan 8, 1976

By D. R. Lawrence

A one-day colloquium on the 'Selection of mining systems and methods' was held at Mintek, Randburg, on 21st September, 1983. The overall theme of the colloquium concerned the underlying reasons for the selection of a particular method or system of mining.

Jan 1, 1983

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By H. H. McGregor

SYNOPSIS Changes in the national productivity (gross national product per head of the population) have been assessed in order to derive a target figure for the required annual increase. The conclusion reached IS compared with the targets of the economic development programme of the Republic. Productivity and management structure in the gold mining industry is then analyzed together with investment in plant, machinery and equipment for rock handling purposes. The conclusion is drawn that productivity improvement does not appear to have accorded with the massive expenditures in plant and equipment, and in augmented management. The productivity of the manufacturing and construction sectors of the economy has been examined. The principal difficulty is that the main avenue of approach is the value of product divided by the total labour force. This introduces inflationary questions, and the use of a suitable deflator becomes of prime importance. Severa1 different methods of assessing the productivity improvement in the industrial sector have been used with what is regarded as a comparatively high degree of compatibility. Improvements in productivity in the manufacturing industry up to 1966 appear, from the information available, to have substantially exceeded comparable figures for the mining industry. There is however evidence that thereafter productivity of the manufacturing industry has not maintained this satisfactory rate of increase. If the economy is to achieve the planned rate of expansion, there is no doubt that greater attention to this aspect will be required in the future than has been accorded to it in the past.

By B. Nemutudi, X. Zhang, B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, S. Pikinini

The comparison study on adsorption of potassium normal butyl xanthate (PNBX) and sodium (nbutyl) dithiocarbamate (SNBDTC) on sperrylite mineral forms a basis in understanding the floatability improvement and paves a way for the design of collectors that may impact on a wide range of arsenide minerals. This study used a computational density functional theory (DFT) and experimental microcalorimetry approach to determine the adsorption energies of PNBX and SNBDTC collectors onto a sperrylite mineral surface. From a computational aspect, we considered the most stable surface plane of (100) surface, which had been found to give the lowest surface energy, compared to the other surface planes. It was observed that the PNBX and SNBDTC preferred to bridge on the As and Pt atoms through the S atoms. These findings showed that the collector adsorbed on the surface through both Pt and As atoms and indicated that the As atoms were significantly active in the adsorptions. We found that the adsorption energies were in the order: SNBDTC (–278.38 kJ/mol) > PNBX (–270.92 kJ/mol), indicating that the dithiocarbamate had stronger exothermic adsorption than the xanthate. From the microcalorimetry test it was also found that the SNBDTC was more exothermic than the PNBX and the adsorption energies were: SNBDTC (–473.50 kJ/mol) > PNBX (–331.13 kJ/mol). These results showed that the nitrogen atom in the SNBDTC collector had a great influence on the adsorption strength of the collector on the mineral surface. This is due to the electron deposition behaviour of nitrogen atoms compared to the electron withdrawing character of oxygen and as such the SNBDTC showed better collecting ability than the PNBX. These results paved the way for the design of collectors for sperrylite and other arsenide minerals and suggested that nitrogen in a collector may significantly improve the ability of the collector for improved recovery. Keywords: Computational modelling, microcalorimetry, SNBDTC and PNBX collectors, adsorption energies

Jan 1, 2020