Search Documents

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

By Rankin W. J

Increasing concern with the emission of sulphur dioxide from smelters and roasters has caused renewed interest in processes which can use waste sulphur dioxide, such as the sulphation of nickel laterite ores. The process described here proposes to by-pass the production of sulphuric acid and react laterite directly with a sulphur dioxide containing atmosphere. A thermodynamic analysis identified operating windows in which nickel sulphate forms while iron oxide (the major impurity in most laterite ores) remains stable. The initial assumptions included unit activity of all species except nickel oxide. The lowest possible nickel oxide activity (while maintaining selectivity) increased with increasing temperature, indicating that selective sulphation is favoured by low temperatures. The temperature of interest was found to be between 500 and 800¦C. Calculations show that a feed gas containing ten per cent SO2, five per cent 02, balance N2 requires a temperature greater than 650¦C for selective sulphation of nickel. Laboratory experiments showed that the assumption of unit activity of ferric sulphate was unrealistic above about 680¦C due most likely to the formation of solid solutions which decreased the ferric sulphate activity. Results are presented which illustrate the limiting equilibrium sulphur trioxide partial pressures at 700 and 730¦C below which selective sulphation occurs. Cobalt extraction was usually between 80 and 95 per cent under conditions yielding selective sulphation, whilst nickel extraction was about 50 to 75 per cent depending on temperature and choice of upper limit of iron extraction. An operating diagram is presented for a limonite ore and shows that the optimum reaction conditions are 680¦C and an input gas containing 20 per cent SO2. Under these conditions nickel, cobalt and iron extractions are 73, 95 and two per cent respectively.

Jan 1, 1996

By Johnston RRM

There have been many published mathematical models that, to varying degrees of sophistication, attempt to describe dynamic thickener behaviour. CSIRO has undertaken to develop a model under industry sponsorship. Recently developed instruments such as the floc density analyser and natural gamma-ray gauge have enabled new data to be collected from plant thickeners for model validation and development. The principles behind the use of the natural gamma-ray gauge are described and the possibilities for its use as a control instrument in the bed have been examined. A simple nomograph illustrates how the gamma-ray gauge data can be used to predict steady state underflow consistency and bed Position.

Jan 1, 1991

By Higuchi K

In this paper, the history of Japanese coal and gas outbursts is presented and circumstances and countermeasures at the time cf outbursts are summarized statistically. Then the present meth- ods for prevention used practically in Japan are introduced. From statistics, it was reconfirmed that Japanese coal and gas outbursts have occur- ed frequently in the district of geological disturbance, symptoms immediately before out- burst occurrence were the phenomena in connec- tion with failure of a coal seam and outbursts have occurred many times when the number of boreholes had not been sufficient to degas. One of the principal protective method adopted in Japan is the large diameter gas drainage boring which also posesses a stress relief effects. There is a tendency to make diameter of borehole larger to increase both stress relief and degassing effects.

Jan 1, 1986

By T D. H McGrath, W P. Staunton

Benchmarking, comparing an operation or process with the industry standard, is known to be a useful method for identifying plant optimisation opportunities, and in many cases providing the pathway to realise the benefits. The difficulty is generating the database of plant data necessary for a benchmarking exercise. Larger companies can benchmark internally; this option is not available to smaller companies, and the full value can only be realised with a comprehensive “industry wide” approach.The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has undertaken several comprehensive metallurgical industry surveys in the gold industry over the last two decades. Analysis of these surveys has demonstrated areas where many operations can benefit from re-assessment of their operating practices.This paper will review the work undertaken by the Group in this area, in particular the 1999 surveys of gold companies in the Australasian region, and the 2012 international survey of the industry. The challenges of, and opportunities arising from these surveys will be discussed. Some of the highlights from analysis of these databases will be presented as well as noting changes in processing practices observed by the Group over the last 20 years.CITATION:McGrath, T D H and Staunton, W P, 2018. Keeping up with the Joneses – the value of industry surveys and benchmarking, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 509–516 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L Clarke, R N. Campbell, F Bourke, J Anderson

Lithological units have been classified geotechnically with mechanical tests and discontinuity measurements from the GRD Macraes Limited, Macraes Gold Project and Rotowaro coal mine open pits, New Zealand. Using these measurements slope stability probability classifications (SSPC) have been quantified based on an adaption of Hack's (1998) SSPC system which places less influence on rock quality designation and unconfined compressive strength than previous slope/rock mass rating systems. The Hack weathering susceptibility rating has been modified by using the chemical index of alteration values from XRF major element analysis. Slaking and weathering is an important parameter in slope stability in the Waikato Coal Measures and Otago schist lithologies and hence a non-subjective method of assessing slaking/weathering in relation to the chemical index of alteration has been introduced. Other major components of this adapted SSPC system are the inclusion of rock moisture content and rock strength anisotropy effects on slope stability. This paper explains the systematic approach of using the adapted SSPC system to classify slope stability probability. The main modifications of Hack's SSPC system are the introduction of rock intact strength derived from Mohr-Coulomb failure criteria which has been adapted for varying moisture content, weathering state and confining pressure. It is suggested that the subjectivity in assessing intact rock strength within broad bands in the initial SSPC system is a major weakness of the initial system. Initial comparison of rock mass friction angles, cohesion and strengths derived from the adapted SSPC are compared with results derived from modified Hoek-Brown criteria, MRMR and SMR classification systems. The advantage of the modified SSPC system is that slope stability probability, maximum batter and overall slope height and overall slope angle for open pit walls can be predicted in addition to orientation dependent and orientation independent stability. Examples are provided, using the modified SSPC system to predict initial optimum pit slope designs in proposed greenfield mine sites.

Jan 1, 2000

INDEX OF CONTENTSBlast Furnace SlagsForehearth AccretionsConverter SlagsConclusionsIllustrationsCOMPOSITION OF SOME COPPER SLAGS FROM PORT KEMBLASamples of copper slags from the Port Kembla Smelter of the Electrolytic Refining and Smelting Co. of Australia, Pty. Ltd., have been submitted for mineragraphic examination, with reference to the mode of occurrence of copper in them. The samples included (I) blast furnace slags, (H) a forehearth accretion, and (IH) converter slags. 1. BLAST FURNACE SLAGS Four series of samples of blast furnace slag have been submitted. The. chemical compositions of the several slags are shown in Table 1. Analyses Nos. 1 and 2 are of samples of slowly or normally cooled slag, taken from the slag dump, Analyses Nos. 3 and 4 are of samples comprising slowly or normally cooled slag, together with granulated slag from the same melt.

Jan 1, 1949

By N K. DavT, A Coggan

The performance of in situ, shallow water covers in controlling acid generation was evaluated at four recently decommissioned pyritic uranium tailings sites at Elliot Lake, Ontario, Canada. The tailings are acid generating, having a pyrite content of approximately five to ten per cent and a very low to non-existent alkaline buffering capacity. Adverse market conditions led to the closure of all operating uranium mines in the early- to mid-1990s, followed by rehabilitation and decommissioning of mine and waste management facilities. In order to control acidic drainage, all new and active tailings areas at Denison, Quirke, Panel, Spanish-American and Stanleigh mine sites were re-engineered to provide in situ submersion of these tailings under shallow water covers. The tailings impoundment dams were upgraded and reinforced or in some cases reconstructed, to minimise seepages and provide a minimum 1 m depth of water cover. With the exception of Stanleigh mine, which was closed in 1996 and rehabilitated during the late-1990s, the water covered Tailings Management Areas (TMAs) at other sites have been in operation for a period of six to nine years. The surface water quality at these sites is maintained at near neutral pH conditions by periodic addition of lime slurry to the established water covers. Additional treatment of effluent is provided as required to meet the discharge water quality standards. The performance of the established water covers at the sites was evaluated by analysing the annual equivalent limestone consumption data. The results were compared with the performance of an older, decommissioned Nordic TMA, which was rehabilitated using revegetation techniques. The water covers at these sites are performing as designed and acid generation has been reduced to low levels. Based on the total amount of yearly equivalent limestone required to maintain water quality in the water cover and at the effluent treatment plant, it is concluded that acid generation rate at the Denison TMA has reduced to less than 0.15 per cent of its pre-water cover conditions during normal operation and rehabilitation periods. In comparison to the revegetated Nordic TMA, the acid generation rates at Denison and Panel TMAs have decreased to less than 1.6 per cent of that at the Nordic TMA. The acid generation rate at the Quirke TMA was comparable or only slightly lower than that at the Nordic TMA because of its unique terraced cell configuration, having tailings in five hydraulically interconnected cells at different elevations. Historic acidity and oxidation reaction products, accumulated during normal operating and pre-water cover periods, are flushing from upstream locations to downstream cells, thus requiring much higher equivalent limestone additions for acid neutralisation and effluent treatment.

Jan 1, 2003

By C J. Unger, A M. Lechner, A Walton, V Glenn, M Edraki, D R. Mulligan

In Australia, responsibility for abandoned mines can be unclear. With a few exceptions, state and territory governments have become responsible for abandoned mines on Crown land and private landholders are responsible for abandoned mines on freehold land. Abandoned mines pose risks and opportunities across the full suite of sustainability themes (environmental, human health and safety, socio-economic and community development) after mining ceases.Across Australia, there are more than 50 000 abandoned mines recorded, ranging in size from individual shafts to large polluting open cut mines. Addressing the safety and environmental impacts of these sites, as well as the socio-economic development opportunities of significant rehabilitation projects, requires the implementation of effective policies and programs. Qualitatively defined graded scales or ‘rubrics’ have been used for many years in student assessment and increasingly in the performance assessment of other sectors (Davidson, 2005). While risk-based maturity models have been used for safety prioritisation (Westrum, 1993; Hudson, 2007; DRET, 2008; Hancock, 2010) and evaluation of organisational development (Esteves et al, 2010), this paper is the first to adapt maturity models for the evaluation of abandoned mine rehabilitation programs in Australia.In this paper, we used indicators based on the national policy for abandoned mines to assess the maturity of abandoned mine programs. Fourteen elements of maturity were identified (Unger et al, 2012) under the five chapters of the national policy for abandoned mines (MCMPR and MCA, 2010). Jurisdictions were then evaluated and ranked on their maturity on the basis of information that was web-accessible. Information transparency of abandoned mines policies and programs is in itself one element of the maturity chart. Each jurisdiction in Australia was compared with one another and with a Canadian jurisdiction; the British Columbia (BC) Crown Contaminated Sites Program (CCSP), which represents leading practice (Unger, 2009; Unger et al, 2012).Our research found that in some jurisdictions in Australia there is little or no information on abandoned mine programs or individual abandoned mine sites on government websites, while other jurisdictions provided very detailed program information on planning, funding and implementation. Each jurisdiction in Australia, for which web-based information was available, had some elements where they were more mature than other Australian jurisdictions. For some elements, maturity ranked equivalent to the BC CCSP, but most Australian jurisdictions were less mature. There was only one element where a single Australian jurisdiction ranked higher than the BC program in maturity. Legacy mine policies, programs, priorities and funding information via departmental websites are easier to find in some jurisdictions, indicating progression toward greater transparency and more mature programs. A systematic approach to monitoring and evaluating abandoned mines programs is essential for accountability as it can demonstrate liability reduction over time and continual improvement. The maturity model approach can provide both a measure of progress over time as well as a tool to support the implementation of the national policy for abandoned mines (MCMPR and MCA, 2010).CITATION:Unger, C J, Lechner, A M, Walton, A, Glenn, V, Edraki, M and Mulligan, D R, 2014. Maturity of jurisdictional abandoned mine programs in Australia based on web-accessible information, in Proceedings Life-of-Mine 2014 , pp 467–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Johnson MT

The microprocessor revolution of the 1970's dramatically improved the price/per- formance of graphics hardware. Together with improved communications and new software concepts and standards this has resulted in the emergence of a new tool with particular application to the mining industry. The Distributed Graphics Processor (DGP) offers more natural means of interaction with com- plex technical models.

Jan 1, 1983

By H Benzer, N A. Aydogan

It is well known that the high pressure grinding rolls (HPGR) can only be operated efficiently under choke feeding conditions in which a material bed is built up between the rollers to ensure interparticle breakage. By increasing the fines amount in the material bed up to a specific level with the recycling load, a uniform material bed is created and higher pressure gradient along the roller width is obtained which results in compact flakes including more fines. Extensive test work has been carried out with an industrial HPGR unit grinding cement clinker in a cement plant in Turkey. During the test work the recycling load of the circuit was changed to achieve different ratios to the fresh feed rate in order to identify the effect of the recycling load on the circuit performance. Six different tests were performed with the circuit at steady state. For each test, samples were collected from HPGR fresh feed and discharge, and total feed, then the particle size distributions of the samples were determined and mass balances around the circuit were calculated. The conclusion was that the reduction ratio of the HPGR increased with increase in recycling load. The flake densities showed the same trend with more compacted flakes being produced for higher recycling loads.

Jan 1, 2009

The Nelson province was chosen as the prime area for rhenium sampling, based on its mineral associations. Sample preparation involved benefication by grinding and flotation A modification of published procedures for rhenium analysis was developed and the results compared with those obtained for molybdenum on the same samples using atomic absorption spectroscopy. The results of the analysis for both metals is discussed and the relationships between rhenium and the molybdenum mineralisa- tion of this region is commented on. A metal- 1ngenic province is defined for molybdenum and r'.ienium and the tectonic setting for this is discussed. Some consideration has been given to rhenium possibilities in Fiordland and the Coromandel Range.

Jan 1, 1980

By B T. Qin, C Zhu, Y W. Jia, Y Lu, F L. Li, Q L. Shi

Air leakage through rock fractures in coal mining is a major cause of coal spontaneous combustion. In order to overcome the deficiency of the existing fire control technology and prevent coal spontaneous combustion by isolating coal from oxygen, the article proposes a novel technology of inorganic solidified foam (ISF) with high expansion to fill fractures effectively. ISF consists of fly ash, cement, setting accelerator, redispersible polymer powder, water and aqueous foam. For preparing homogeneous and stable ISF, a preparation system with a pore type foam generator, a mixer device installed with a hollow shaft and helical blades, air compressor, slush pump and monitoring instruments was developed, and the working principles of key devices were elucidated. Based on a series of experiments on the different ratios of each component material and technological parameters of the preparation system, ISF with a foam expansion ratio of 8~10 and dry density of 250–400 kg/m3 was prepared. The relationship between elastic compressive strength, modulus of elasticity and density was summarised. Based on the injection experiment for fracture of loose coal pile with high temperature, the characteristics of sealing air leakage, compressive strength, thermal insulation, flow and cooling of ISF in the fresh state were investigated, indicating that ISF can effectively cut off the air leakage and cover the coal sample to reduce the temperature in the earlier stage, and ISF can remain stable and not crack. The ISF was applied to Luwa coalmine to seal small coal pillar pressure fractures and loose coal fractures in goaf. After press-casting the ISF in Luwa coalmine, the pressure-difference of inner-outer increased, meaning the effect of external conditions on the pressure-difference decreased, showing that it could plug the air leakage effectively.CITATION:Qin, B T, Shi, Q L, Lu, Y, Zhu, C, Li, F L and Jia, Y W, 2015. The novel technology of inorganic solidified foam with high expansion for preventing coal spontaneous combustion, in Proceedings The Australian Mine Ventilation Conference, pp 121–126 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Burgess JM

Research on gas distribution in the iron- making blast furnace has been conducted in three separate areas. Firstly, experimental work has been conducted to determine the important parameters which dictate the pressure losses in homogeneous and heterogen- eous packed beds. Secondly, a theoretical analysis of gas flow through the furnace softening-melting zone has been undertaken to determine the effect of the shape of the zone on the distribution of gas flow towards the furnace walls. Thirdly, a theoretical programme has been undertaken to develop methods for the prediction of furnace soften- ing-melting zone shape from furnace tempera- ture and gas composition measurements.

Jan 1, 1980

Using Dynamic Simulation Throughout a Process Plant's Life Cycle

Sep 13, 2010

By X Sun, L B. Zhou, H Yi, X Tang, P Ning

The rapid industrialisation in China has consumed large amounts of various industrial raw materials, which has left behind large quantities of industrial solid wastes produced from the processes of mining, mineral processing and smelting. The storage of huge quantities of industrial solid wastes is an obvious risk to the environment and human well-being. As the first step to fully appreciate the scale of this risk, it is necessary to carry out research for developing a pollution source environmental risk assessment system (PSERAS), especially for the typical staple industrial solid waste (TSISW). This paper aims to discuss the frame of the PSERAS for TSISW for large scale production. This system consists of two aspects: predicted factors and accidental ones, which involve physical, chemical and biological risk assessments, on-site and during transportation process. Two analysis methods, the analytic hierarchy process (AHP) and fuzzy logic assessment (FLA) were used to handle the complexity of environment and non-quantitative data. The risk assessment system for such a complex objective is difficult and the assessment of relative factors is problematic through the usual quantitative analysis. With the proposed PSERAS, it is possible to define the risk class of pollution sources. Furthermore, the risk assessment results will be helpful to the decision-maker, especially when facing unknown risks in the environmental management of industrial solid wastes. In addition, by means of the PSERAS, risk factors can be ranked against their contributions to environmental risk, in order to calculate their relative priorities in decision-making.CITATION:Sun, X, Ning, P, Tang, X, Yi, H and Zhou, L B, 2012. Environmental risk assessment system for typical staple industrial solid wastes, in Proceedings Life-of-Mine 2012 , pp 301-304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D Corley, J Moore, M Grant, A, W R

Resource estimates are the corner stone of technical and investment decision-making. Prior to mining, resource estimation uncertainty has the greatest potential to lead to poor investment decisions, despite a significant component of resource estimation uncertainty being unknowable at this critical stage in the mining cycle. This presents a conundrum to the resource geologist in terms of risk evaluation and resource classification. Ahead of mining, there is normally considerable focus on drill hole spacing analysis to determine the ‘optimal’ drill hole spacing, taking grade and geological continuity into account; cost-benefit analyses balance improved resource definition against cost; the law of diminishing returns and the exponential cost increases acting together as spacing is reduced. Typically, a lower limit to the drill hole spacing is identified. After completing the resource drilling to an agreed spacing, resource estimation is then undertaken. At this point it is common to attempt to bracket the resource estimation uncertainty. In many cases conditional simulation is used, based on a modelled, but largely assumed, variogram model. It is also assumed that the histogram of the available drill hole sample data is representative of the in-ground mineralisation. The purpose of this paper is not to diminish the importance of drill hole spacing and simulation studies, but rather to illuminate an important aspect of estimation uncertainty that, although previously recognised, is typically overlooked – the question of how representative the available data set is in characterising the true (but unknown) distribution of mineralisation. To do this, we lift the lid on one of OceanaGold’s former operations, the mined-out Globe Progress Mine, by resurrecting a high quality, close-spaced, reverse circulation (RC) grade control data set. The Globe Progress Mine is within the West Coast Region of New Zealand, it was closed and transitioned to rehabilitation in 2016 and is now known as the Reefton Restoration Project. The exhaustive Globe Progress grade control data was used to repeatedly ‘redrill’ the deposit by extracting 35 m × 35 m spaced subsets from the original 5 m × 5 m spaced grade control data. Utilising closely spaced grade control data removed the need for assumptions regarding short range continuity, which are necessary with forward-looking analyses that are based upon broader spaced resource drilling. The extraction process used a nearest neighbourhood algorithm, repeatedly moving the origin in 5 mE, or 5 mN increments. Individual resource estimates were then completed for each of the extracted drill hole data sets (49 in total) as well as a grade control estimate based upon the exhaustive data set. Whilst the data unpinning each of the 49 estimates changed, the geological assumptions, variography, and modelling parameters remained constant. This approach was taken to isolate the impact of changing the input data. The 49 estimates were then compared against each other and the grade control estimate. The mean of all 49 sensitivity estimates was close to that of the grade control estimate in terms of contained gold, tonnes and grade. Whilst it is acknowledged that the grade control estimate itself is subject to some degree of estimation uncertainty, the close match between the average of the 49 estimates and the grade control estimate suggests that the resource estimation methodology is reasonable and appropriate. Whilst this comparison is important, the focus of this study is on the component of estimation uncertainty related to the underlying data, and this is reflected in the spread across the estimates. The spread across the 49 global estimates (highest to lowest) for this particular Mineral Resource Estimation Conference 2023 | Perth, Australia | 24–25 May 2023 142 case study was found to be significant (approximately 20 per cent in grade and metal) and that is attributable solely to the underlying data. This exercise quantifies a component of the estimation uncertainty that is inherent to all drill hole data and is distinct from the uncertainties associated with modelling methodology choices, sample and subsample quality and drill hole spacing-related interpolation uncertainty. Importantly, this uncertainty is unknowable prior to mining; we can only directly compare the resource drill hole data against grade control data after mining has taken place. For the case study, approximately 65 per cent of the estimates fell within 5 per cent of the grade control estimate for contained-gold, suggesting that for many projects the histogram of drill hole data is unlikely to differ noticeably from that of the in-ground resource. However, about 15 per cent of the estimates in this study differed by more than 7.5 per cent, suggesting that a not-insignificant proportion of estimates will be materially compromised. Whether or not the available drill hole data is representative comes down to the ‘luck of the draw’ and cannot be known at the time of resource estimation. Given the challenge of attempting to evaluate forward-looking estimation uncertainty, a component of which that can only be quantified retrospectively, what should we do as resource geologists? What are the implications for risk evaluation, resource classification and reconciliation? Furthermore, without rigorous post-mining data checks, resource geologists may conflate suboptimal modelling with the shortcomings of the underlying data. An example of this problem is discussed in the following section.

May 24, 2023

Following a decline in direct and indirect employment in the minerals industry between 2000 and 2003, the situation reversed in 2004 and employment rose by 12 per cent. Furthermore, there are forecasts of continuing employment growth in the minerals industry in the immediate future. For those of us charged with promoting the virtues of a career in the minerals industry this is encouraging news, as it provides us with the evidence to promote the increasing employment opportunities of a healthy and vibrant industry. However, for many others û particularly the employers in this industry û the news is not so rosy. The jobs are there, and in increasing numbers, but the workers arenÆt! Employers right across the industry are finding it increasingly difficult to fill vacancies with suitably qualified and skilled employees and the competition is becoming fiercer. In the minerals and energy sector, questions are being asked and solutions sought on the industryÆs ability to attract and retain a skilled workforce. From many quarters û industry, government and the education sector, calls for urgent action are becoming louder. The reasons for this are well known û the nature of the work, the remote location, perceptions of the industry, an aging workforce, the gender imbalance, the shrinking demographic of school leavers. It is the latter I wish to focus on û the Generation Y demographic û those who have recently left school, those who are in higher education or have recently entered the workforce, or those who are still at secondary school. These young people are the next cohort of potential employees for the industry. But our need for them appears to be greater that their perceived need for us! How do we engage them so they are informed about the industry? How do we inform and advise them so they are prepared to consider further education and training in disciplines and skill areas relating to our industry? How do we guide and motivate them to give it their best shot and work in it û at least for part of their working life? These are fundamental questions that many within the industry have been grappling with for quite some time. Let me share with you some of the strategies that the Minerals Council is implementing to address this issue.

Jan 1, 2005

By J Pease, P Cameron, D Drinkwater

"In the 1990s metal prices were trending in a long-term decline and the usual cost-cutting exercises were adopted. Cuts to research and development made innovation difficult and the outlook was grim. But necessity is a strong motivator, and these conditions spurred the Mine to Mill movement that optimised across organisational ‘silos’ and utilised new technology tools, innovative software and increased computing power. Many applications of Mine to Mill exploited the fact that comminution is usually the site processing bottleneck and blasting is more efficient at breaking rock than grinding. This approach sought to: understand and characterise rock breakage from mining to the milldevelop models and simulators for blast design, fragmentation, crusher and mill circuitsdevelop tools to measure in real time the particle size distribution of rocks on run-of-mine (ROM) muck piles, at the primary crusher truck dump pocket and on conveyorsensure effective communication across the silos between geologists, blast design engineers, mining engineers and metallurgists.These methods and the technology tools available in the 1990s were widely adopted at numerous sites around the world with significant benefits. Semi-autogenous grinding (SAG) mill throughput increases of 10–20 per cent were common. This was the advance the industry desperately needed. It was low capital cost; it was obvious. It was here to stay.Except, in too many cases, it didn’t. In the minerals price boom of the 2000s Mine to Mill was no longer necessary to ‘survive’, even though it was still good business. Some operations, including some of the early success stories, slipped back to old habits of optimising within organisation silos instead of across them. Fortunately, other operators still embraced Mine to Mill and developed new techniques. Mine to Mill was still successful, but not as widely adopted as we had expected it to be. Now the boom has ended and operations are again under cost pressure. Since these are the same circumstances that created Mine to Mill, it seems time to achieve the wider adoption. Since the 1990s many new or advanced technology tools are now available for Mine to Mill projects: blasthole sensors, new explosives formulations, new blasting techniques and modelling, ore tracking devices, improved image analysis to determine size, texture and colour of coarse ore, grade sensors, whole-stream simulation tools, and even more powerful computing hardware and data analysis software. If we could achieve so much in the 1990s, how much more can we achieve today when we have the same imperative, the same potential and a larger number of high technology tools?Citation:Cameron, P, Drinkwater, D and Pease, J, 2016. The ABC of Mine to Mill and Metal Price Cycles, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Fukuda M, Kurita K

A mathematical model for estimating the liquid level in the hearth is presented. The analytical result was checked on a cold two-dimensional model and an additional boundary condition for the fundamental equation resulted. The applicability of the resultant equation was investigated on a cold model and a regression equation obtained for the average liquid level for Kashima No. 1 BF. Comparison of calculated and observed results were in fairly good agreement. It is concluded that the liquid level in the commercial furnace can be calculated from the measured values of pressure in the bosh and operating conditions.

Jan 1, 1975