Search Documents

By Saeed Zandi, Kazem Oraee

"Tunnels and galleries are the most important structures in coal mines. They are used for variety of purposes, such as transporting ore and people and for ventilation. A well-designed support system is necessary to stabilize structures and prevent collapse.Using rock bolts increases the strength of the rock in which tunnels are made. Rock bolts are used extensively in most underground mines today, and coal mines are no exception. Almost all galleries in a typical coal mine use some type of rock bolt, at least, as a means of partial or supplementary support.In this research, changing the support system from expensive methods to the use of rock bolts as the primary means of support is discussed, with the focus on a particular gallery in Hejdak coal mine. Visionary design methods, in conjunction with rock mass classification schedules, were used to determine an optimal rock bolt pattern. For this purpose, rock mass rating (RlVIR) and quality index (Q) classification systems were used. Several empirical methods were also used to design an optimal pattern for rock bolt installation in the particular tunnel under analysis.As such, the tunnel support system was designed using both finite element and empirical methods. Finally, the results obtained from both numerical and empirical methods were compared under different load conditions. The methodology prescribed in this paper, together with the comparison, can be a useful tool when selecting a support system. The results can also be used to design a support system in this and any other coal mine with similar conditions.INTRODUCTIONSince the advent of underground excavation techniques, one of the biggest challenges has been stabilizing tunnel walls and preventing roof collapse in tunnels and other underground openings, such as galleries. Loose rocks and layers drop into tunnels and galleries, except in very hard rock. Underground roof collapse and falling rocks can have devastating effects on the safety of operation personnel and equipment and can seriously affect production. When designing an underground coal mine, the stability of tunnels and galleries is an important parameter that should be studied carefully because it has an important role in the production process of the mine. Therefore, an appropriate and well-designed support system is necessary for preventing collapse and helping to stabilize the tunnels and galleries."

Jan 1, 2016

By Brian G. D. Smart

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be represented.

Jan 1, 1992

By George J. Karabin

Since the inception of a qualitative pressure arch theory by Haak4 in 1911, much work has been done in an effort to apply this concept to underground mining. It has been used in both longwall and room and pillar mining to determine roadway and pillar stability (with varying degrees of success). This paper presents a summary of a case study where the pressure arch concept was extended in a totally qualitative manner to define the source of roof control problems in the mains of a Pennsylvania mine. It was concluded that, due to the method of mining employed, a pressure arch formed over a portion of the entries, and the high abutment stresses accompanying it resulted in extreme roof deterioration. The following discussion will include a general presentation of the arching mechanism, the physical response of the roof strata under mining-induced abutment stresses (both from the case study and in general), a computer simulation of ground stability under both "normal" and "abutment" stress conditions, and finally, potential means of alleviating such conditions.

Jan 1, 1982

By Yi Luo

The responses of a section of railroad to ground subsidence process was monitored as it was undermined by a longwall panel. The subsidence data collected and the observations made through this monitoring program could help us understand betteer the ground subsidence process and its impact on linear structures such as railroads. The data analysis techniques used and the assessment methods presented could be useful to researchers practitioners in the field of mining subsidence.

Jan 1, 1994

By Larry Stolarczyk

The mining industry would benefit greatly by imaging geologic conditions well in advance of mining. In layered deposits such as coal, trona, quartz, and potash, natural waveguides form and enable electromagnetic seam waves to travel great distances. In the early 1980s, the Radio Imaging Method (RIM) was developed to capitalize on electromagnetic seam wave propagation in the assessments of seam conditions in longwall panels. The initial applications of RIM tomography and comparisons to in-mine mapping of geologic conditions proved that faults, paleochannels, and rapidly thinning coal could be detected and imaged with seam waves. This paper describes the application of electromagnetic seam waves in mapping the margins of a paleochannel crossing a longwall panel and the interesting possibility of adopting the newly developed Full Wave Inversion Code (FWIC) )Newman 1995) to significantly improve imaging resolution. When tomography images are combined with ground control science, a significant reduction in cost, roof fall potential, and waste rock in underground mining may be realized.

Jan 1, 1999

By Changshou Sun

Excessive deformation occurred in the underground openings of Jinchuan Nickel Mine, the largest nonferrous underground mine in China. Developed in weak rock formations at great depth, the underground openings are under great in-situ stresses with the horizontal stress being twice as high as the vertical one. Based on in-mine observations and in-situ testing results at the mine, time-dependent mite element simulations with coupled creep and plasticity constitutive models were conducted in this study to analyze the stability of underground openings In the study, the Burgers creep model and the Drucker-Prager plastic model were coupled to simulate underground drifts and cut-and-fill stopes. Two-dimensional finite element models were developed with ABAQUS - a comprehensive finite element simulation package The study investigated the behavior of underground drifts at great depth with high horizontal stress and the behavior of cut-and-fill stopes with various stope heights and fill conditions. The numerical simulations revealed important characteristics of opening deformations as a function of time after excavation and location relative to the wall of opening The results had good agreement with field monitoring data, They provided useful information to aid mine engineers in the design of mine openings, the selection of opening supports and the determination of support installation procedures.

Jan 1, 1999

By George B. Quaye

Conventionally, roadways in South African collieries are 6 to 7 m wide. This dimension is chosen so as to allow maneuvrability of appropriate mine machinery and equipment, to meet production requirements and to ensure roof stability. Over the last two decades, a great deal of research effort has been expended to understand the behaviour of roadways in different strata within this width range. The results have improved the understanding of the strata behaviour to such an extent that 6 m wide roadways are developed with a high degree of confidence. With the advancement of technology and the quest to mine at a lower cost, some mines in South Africa have started considering the benefits of other types of mine machinery that will require much wider roadways to ensure optimum productivity. The roadways required will have to be about 10 - 14 m wide. The challenge confronting these coal mining companies is the potential instability that might be associated with such wide roadways. This dilemma is aggravated by the fact that, apart from theory, nothing is known about the expected behaviour of such wide roadways. This led to experimentation at a selected site in a South African coal mine where 10 m and 14 m wide roadways were developed and monitored. This paper highlights the experimental procedure adopted, discusses the results obtained, compares the prediction of elastic theory to reality and set the precedence towards understanding the behaviour of wider roadways in South Africa.

Jan 1, 2001

By M. E. Duncan Fama

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface modelling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model predicted the fender would suffer considerably more deformation and strain.

Jan 1, 1992

By Dennis R. Dolinar

The U.S. Bureau of Mines has modeled yield pillars to determine the effects of reinforcement techniques on pillar performance. Model pillars with width-to-height (w/h) ratios ranging from one to four were reinforced using advanced lateral support systems. To evaluate reinforcement and pillar performance, the model pillars were strained up to 18.6 pct in compression. The results show that the reinforcement had a significant effect on the postfailure characteristics of the pillar but had only a small effect on it's maximum failure strength. Pillar residual strengths increased up to 10 times, while the energy capacity increased by a factor of three depending on the reinforcement method. At maximum deformation, the residual strengths of several types of reinforced specimens exceeded the maximum compressive strength up to 2.5 times and resulted in an increasing positive postfailure stiffness. Test results, data analysis, and application of the results to underground mining are discussed.

Jan 1, 1993

By S. Kramadibrata

It has been well accepted that water content significantly changes the physical and mechanical properties of rocks. Experimentation data of Uniaxial Compressive Strength (UCS), Modulus of Elasticity (E) and Brazilian Tensile Strength (UTS) of sandstone showed that increasing water content from oven dried to saturated condition will decrease their values. Ultrasonic tests carried out together with the UCS tests also indicated that the sonic wave traveled faster as rock specimen became saturated. During triaxial tests, the sonic velocity changed with the applied load. It was found that constitutive behavior of dried rock specimen was dependent on the confining pressure, whereas saturated rock specimen did not seem to be dependent on the confining pressure. Dependency of failure criteria such as Mohr-Coulomb. Bieniawski and Hoek & Brown on the water content was conformed as well. In order to show the influence of water content on the stability of an underground opening, a numerical modeling, based on finite element method, was carried out. The model was run using the mentioned failure criteria.

Jan 1, 2000

By A. Wahab Khair

This paper presents an analysis of surface ground movements recorded from two longwall mines in Northern West Virginia which operate in the Pittsburgh Seam. The instrumentation areas consisted of four panels, two at each mine, covering various sections with unique topographic features. Instrumentation consisted of survey monuments on 25 to 120 ft. spacing. Vertical and horizontal ground movements were measured at specified intervals to determine subsidence rate, developing and final subsidence profiles, angle of draw, horizontal displacements and associated strain profiles. A relationship between panel depth and width and the subsidence factor was also developed.

Jan 1, 1988

By B. G. D. Smart

The development of a softwood alternative to the hardwood chockpiece used to build the waste-edge breakers commonly incorporated in gateroad packs is described. The results of laboratory tests on softwood prototypes and two underground trials are presented. The results of the last trial suggest that a viable alternative chockpiece has been designed, offering advantages over availability of wood, weight and given reduced wood content, price.

Jan 1, 1992

By Gregory J. Chekan

Developing a coal seam that has been influenced by previous mining in seams either above or below can result in severe ground control problems. In many instances, interactions between operations are inevitable. but improvements in ground stability can usually be achieved by-predicting potential problem areas in advance and adjusting the mining plans accordingly. This report investigates four case studies involving interactions between operations that used both room-and-pillar and longwall mining methods. In each case, geologic and mine design parameters are addressed, and those parameters found critical to the interaction are further defined in relation to observed ground problems.

Jan 1, 1990

By Marek J. Mrugala

Coal strength based on scaled uniaxial compressive strength from the laboratory and back calculations from in-mine observations of pillar stability indicate that material strength scaling rules are open to debate. Analyses presented indicate that the application of scaling factors lower than 0.5 provide a better correlation with field observations of pillar stability.

Jan 1, 1989

By Xun Luo

In this paper we report on the use of microseismic monitoring techniques to investigate the fracturing process associated with longwall mining. The study was carried out at three mines in Australia and concentrated on some major concerns of the mines, such as failure patterns and growth rate associated with mining progress, their implications to water ingress and gas emissions, caving processes in the goaf and precursors of roof falls. The results have shown that a zone of shear fracturing has occurred further ahead of the longwall face than predicted using conventional longwall geomechanics theory. Failure patterns in the roof and floor vary from mine to mine and this appears to be dominated by geological structures. The reaction of faults, the formation of fractures which allow gas emissions and precursors roof falls have also observed. Results from this work have opened up new understanding of longwall caving processes and proved that microseismic monitoring is a very useful technique for studies of longwall geomechanics and hazard controls.

Jan 1, 1998

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term "burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the futures of high frequency, great strength and shallow depth of the beginning burst have been found. There ere some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By Yingda Zhai

The range of interburden thickness between coal seams in Datong Mining District of China is large. From mining operation point of view, the closer is between the two seams, the greater is the impact from the upper seam when the lower seam is mined. This impact is most notable when the two seams are ultra-close. In this paper the definition of ultra-close seams and its practical method of determination are presented. Based on the difference in strata thickness in the interburden and the concept of "yield depth ratio" which is defined as the yield zone depth in the interburden to the total thickness of interburden, the roofs of the ultra-close multiple seams in the Datong District of China were divided into 3 types: (1) false roof or rock partings in coal seam. This type of roof does not require special handling except mining them simultaneously as one single seam. The roof thickness is slightly less than 0.5 m; (2) completely broken roof. In this type of roof, the yield depth ratio is larger than (or equal to) 1. When the roof thickness is larger than 0.5 m but less than 2.0 m, the yield depth ratio must be smaller than 1; and (3) fractured roof. In this type of roof, the yield depth ratio is less than 1 while the roof thickness is larger than 2.0 m. In retreat longwall mining, if the gateroads of the lower seam are located under the gob of upper seam, roof bolting can be used in the 3rd type of roof. But if the 2nd type roof exists, powered supports must be used.

Jan 1, 2005

By Dale S. Preece

In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer program have been used to determine the creep closure and structural stability of salt caverns. Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minium pillar to dimeter ratio. , P/D. These numerical predictions indicate that the current cavern design is safe.

Jan 1, 1984