Search Documents

By Eric Reale

The New York City Department of Environmental Protection (DEP) is currently building City Water Tunnel #3 beneath the city. The purpose of this tunnel is to improve water distribution to the city and to allow the DEP to inspect the older tunnels and make the necessary repairs. These older tunnels have been in continuous operation since the early 1900's. Construction on the Third Tunnel is planned in four stages. The Nelson Street Shaft, which is the focus of this paper, is part of the second stage.

Jan 1, 1989

By Tom Short, Paul Kunze

In this paper, the authors describe major changes in drilling and blasting methods instituted at the Zortman And Landusky Mining Company Properties to maintain the viability of these north central Montana surface mines in the present period of depressed precious metal prices. The authors explain how improved drilling procedures minimized problems due to uneven benches and floors. They also describe changes in explosives loading and delay blasting techniques which improved fragmentation, thus increasing metal recovery from heap leaching. Quantities were increased substantially and a new bulk explosives loading system was placed in service with a special down-the-hole bulk loading truck and storage facilities for bulk ANFO and bulk emulsion. At the same time, drill patterns were expanded by nearly 40%. The authors also describe a new technique of using explosives to selectively cast waste and ore in different directions so as to reduce the cost of separating the ore.

Jan 1, 1986

By Yessica Idrogo, Omar Gómez, Francisco Pérez, Eduardo Yrigoyen

Rock blasting is one of the most important operations in the mining cycle value chain, requiring optimized explosives mixtures to get good results. A new and better strategy, and that which is discussed herein, is to design a new emulsion explosive, which can provide improved characteristics and benefits over and above general types of emulsion explosives. It is therefore critical that this product is functional over a wide range of conditions

Jan 1, 2019

By W. Birch, G. D. Rangel-Sharp, L. Bermingham

For many years, the accepted method of Measuring the Velocity of Detonation (VOD) in blast holes has been to use an electric cable of a constant resistance per metre. Thus as the wire is consumed by the explosive in the blast hole, the change in resistance is monitored and when this data is plotted against the time period of the in hole explosion, the VOD can be calculated.

Jan 1, 2011

By Marcus Neves, Eventomar Junior, Adilson Castro, Leandro Silveira, Sérgio Augusto

The collapse of the Vale S.A. mining tailings dam in 2019, a tragic event that shook Brazil and the world, had consequences that transcended the immediate pain and devastation. Among them, the suspension of rock blasting activities in several mines in the Quadrilátero Ferrífero region of Minas Gerais, Brazil. This measure, taken as a precaution and with the aim of ensuring the safety of nearby geotechnical structures and the population, had a significant impact on the mining production chain. To overcome these challenges and resume blasting activities in a safe and sustainable manner, the mining industry has been dedicated to developing and improving solutions. One of the promising alternatives is the signature hole technique, used in conjunction with attenuation laws. The complex geology of the Quadrilátero Ferrífero, with lenses of compact ores immersed in friable materials, the presence of discontinuity families, and the emergence of geological faults, requires detailed analyses and specific adaptations of the signature hole technique and constant monitoring of the vibrations to calibrate the attenuation laws to ensure compliance with permissible limits and safety of the operations. To demonstrate the methodology, a case study in Abóboras Mine was described. Additionally, the challenge of achieving the desired level of production while controlling vibration and slope damage has driven the development of new charging and timing techniques. To address this challenge, a comprehensive approach was undertaken. A substantial database containing more than 4,000 registers of blasting-induced vibration events from 520 blasts was meticulously compiled from 2020 to 2023, 6 different attenuation laws were established and continuously calibrated with 99.3% of compliance regarding permissible limits of vibrations. The successful implementation of these actions allowed for the resumption of blasting, increasing production from 10 million metric tons to 43 million metric tons per year assuring sustainable operation.

Jan 21, 2025

By Lifeng Li, Jhon Silva-Castro

"Signature Hole Technique is one method to assess the vibration waveform of a production blast.Methematically, it is the convolution between a prior measured waveform of a single blast hole (signature) and a given time delay sequence (comb function). Being an advantage, the inverse operation of convolution, known as deconvolution, can be used to estimate the signature."

Jan 1, 2017

By Mike Higgins

"The purpose of mining and its related industries is the removal of, and usually the subsequentprocessing of, material from the earth. This includes mining for minerals, quarrying for stone, and civilexcavations. Where this involves rock, the most common method is to fragment the rock by blasting. "

Jan 1, 1997

By Italo Onederra, Gary Cavanough, Ewan Sellers

Reactivity of ammonium nitrate based explosives is associated with the presence of iron sulfides in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. The stability of explosive products can also be linked to in-hole density, which influences detonation efficiency, breakage performance and the potential generation of Nitrogen Oxide (NOx) fumes. Reactive ground testing involves detecting a temperature rise of a mixture of a bulk explosive product sample, a ground rock sample and some specific chemical agents. This paper describes improvements in reactive ground testing involving the use of time lapse video analysis and detection of NOX gas emissions from the sample. Reactivity is stored and linked to a using cloud based software to map of the mine showing the exact location of the sample. The location marker can be selected to allow quick access to the sample test results and video. In addition to reactivity, the stability and detonation performance of bulk product can also be influenced by depth. In this paper, a system that simulates product at depth and measures density changes and monitors the structure of bulk samples is described. Results from an explosive product are analyzed and detonation performance is assessed by the measurement of velocity of detonation and detonation pressure.

Jan 1, 2018

By R D. Skaggs

A good blast is dependent on a well engineered design. However, a good design's performance depends on the control of the drilling and loading of the blast holes. The key stone to good blasting is the drilling of straight holes of the correct orientation in the required positions.

Jan 1, 1991

By Dale S. Preece, Ruilin Yang

"Air-decks are often employed for presplitting along the final highwall of a blast and are sometimes also included at the bottom or in the middle of explosive columns in the production portion of a blast. Shock wave physics is an important part of air-deck behavior since the bulk explosives in the column impart a shock into the air-deck where the air shock then passes through the air-deck at a rapidlyattenuating velocity. Through both high-fidelity modeling and shock physics theory it is shown that theresulting pressure in the air-deck is two orders of magnitude less than the detonation pressure of theexplosive."

Jan 1, 2017

By O E. Crenwelge

Seismograph measurements are usually made near blasting operations solely for the purpose of monitoring compliance with governmental regulations. However, recordings of seismograph signals have far greater potential than this, if the proper procedures are used for analyzing the transient data.

Jan 1, 1991

By Gordon Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is ofien complex, particularly when risks are high.

Jan 1, 2001

By Per-Anders Persson

This chapter deals with the concepts of shock wave8 and detonation wavea together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the context of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of an explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of thii chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1998

By Li Jianjun, Zhang Xiaozhi, Guan Li, Jin Jinzhe

People used to regard emulsion explosives as the safest industrial explosives. But in the process of manufacturing emulsion explosives spontaneous ignitions of the remnant emulsion matrix have happened under the conditions of constant or low temperature. These fatal accidents show both emulsion explosives and emulsion matrix may involve hidden danger. Since the temperature in its production emulsion matrix is high, emulsion matrix is sensitive to mechanic action.

Jan 1, 1998

By J. Aravena, S. Gajardo, M. Ayala, P. Salinas

Both, Teck Carmen de Andacollo (Teck CDA) and Orica, work hard in the implementation of new technologies available in the explosives industry and drilling and blasting techniques, with the objective of sustainable development of their operations, regeneration, and protection of the environment, also considering the welfare and relationship with the surrounding communities. The open-pit Carmen de Andacollo mine is located adjacent to the town of Andacollo. Therefore, both companies together have developed the implementation of different techniques and technologies to mitigate the impacts of mining operations in the community, considering an important part of this challenge to minimize the impact of their perception of blasting by reducing the level of vibrations and sound pressure (airblast), in addition to the control of dust and smoke, strengthening sustainable production in harmony with communities. The technologies and techniques that have been implemented are the installation of airblast and vibration monitoring stations stands out, whose database has records since 2011. Using the vibration database, different models were developed to predict the vibration level of blasting in its design phase, achieving a difference of 4.1% between the estimated and measured values in the last year. Two techniques stand out to minimize the ejection of material, "Hydraulic Dome" and "Dual layer blasting", the first consists of water irrigation on the surface to be blasted and the second is an unconventional blasting technique, which was awarded in 2015 for its results in the environment. Also pre-splitting engineering has been modified in a positive evolution, where through different configurations, the airblast has been reduced by 15% compared with records from 2011 to 2022. Finally, due to the impact of operational restrictions, such as days available to blast, number of holes, and powder factors, the wireless initiation technology was implemented, which allowed reducing the limitations in the loading, generating an improvement in terms of blasted materials over conventional systems. Understanding the restrictions and challenges in terms of impact on communities, the correct implementation of all these techniques is important, and in conjunction with collaborative work, it has been shown and validated that producing in a sustainable and sustainable manner is possible.

Jan 1, 2024

By C. Liley

Open cut blasting at the Ernest Henry mine has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project which was conducted to ensure pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units.

Jan 1, 2012

By Robert Hopler

HUDSON MAXIM A Noted Inventor of High Explosives ALTHOUGH the subject of the present sketch has been a tireless worker in many fields of activity, his name is best known in connection with his work in the development of high explosives and their application to modern ordnance

Jan 1, 2012

By J. Eloranta

"Previous work indicated that the annual per-capita consumption of raw aggregate material averages about 10 tons; half of which is produced by blasting. Given a population of approximately 320 million in the United States alone, this amounts to 1.6 billion tons of blasted material annually. It was also estimated that up to 20% of the blasted material in aggregate operations is smaller than 6.35 mm (1/4inch) in size. Thus, about 320 million tons (i.e. 1 ton per capita) of byproduct is produced annually and sold at significantly lower prices or potentially discarded in waste dumps."

Jan 1, 2017

By Hubert den Dikken

ache, especially when it comes to forwarding of small quantities. Air transport is limited to 1.4 explosives on cargo aircraft and 1.4S classified explosives on passenger aircraft, so most samples cannot be transported by air. Ocean transport is a possibility, but due to stowage and segregation regulations of the IMDG code, a very expensive one. Road transport is often the only solution, but high explosives require special trucks with licensed drivers. The solution to these logistic problems is solved by creating a 1.4S (Class C) classification for all high explosives, when packed in special containment vessels.

Jan 1, 1995

By C. K. McKenzie

Presents outline of flyrock model and a field procedure to validate predictions of maximum projection distance. Field results are presented from 13 field tests with two different hole diameters.

Feb 1, 2020