Search Documents

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023

By Alen Shibu Joseph, Arvind Rajnarayan Singh, Mudila Dhanunjaya Rao, Kamalesh K. Singh

In this article, the cementation of major impurities from zinc sulphate leach solution by the addition of zinc dust was studied by considering different parameters including time, mesh size, and percentage of excess zinc dust. The output obtained from various experiments was utilized for the design of experiments. A multi-level categorical factorial design with a quadratic model was employed during this study. Results were predicted to minimize the concentration of impurity metals in the solution by altering the parameters. Furthermore, these predicted results were validated by performing another experiment. Successfully, it showed that the predicted and experimental data values were close to each other. The predicted optimized values were 40 min, 100% excess zinc dust, and 300 mesh size for copper; 42 min, 100% excess zinc dust, and 300 mesh size for cobalt; 37 min, 100% excess zinc dust, and 300 mesh size for cadmium; and 34 min, 100% excess zinc dust, and 300 mesh size zinc dust for nickel. At these optimized values, the experimental results showed 99.99%, 55.7%, 99.6%, and 76.6% cementation efficiencies for copper, cobalt, cadmium, and nickel respectively. The statistical design of experiments for the effective cementation of impurities corroborates the economic feasibility of optimizing parameters for the proposed process.

Jul 18, 2022

By M. P. Roy, P. K. Singh, A. K. Mishra, Ashish K. Vishwakarma, Vivek K. Himanshu

Ground vibration is one of the major hazards produced by rock-blasting operation. The accurate prediction of vibration is necessary for designing controlled blasting parameters. The existing vibration predictors consider maximum explosive charge weight per delay and distance as the parameters responsible for ground vibration. These predictors are based on the assumption that the geometrical parameters of the blast will be constant for a site. However, the mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, the other blast design parameters will also have an impact on ground vibration intensity. A principal component analysis is a dimension reduction technique. This technique along with multivariate logarithmic regression has been used in this paper to predict the ground vibration. The technique has classified the blast design parameters into four principal components. The regression with the scores from these principal components has been carried out. The evaluation of the model performance of predictors along with the existing empirical predictors has been carried out using R2 and RMSE values. The evaluation suggests that the predictor with logarithmic regression followed by principal component analysis gives better performance with respect to the existing empirical predictors.

Jul 30, 2022

By Rameshwar Sah, Basavaraja Maribasappanavar, Sangamesh Desai, G. Balachandran, Ravi Kant Sagar

The present research work deals with the effective utilization of hematite ore containing goethite, kaolinite and gibbsite losson- ignition (LOI) phases in pellet making without deteriorating product pellet properties by optimizing the induration cycle especially drying and preheating of pellets. Adequate drying and preheating of pellets before sintering is of prime importance to sustain the desired properties of pellets. Green pellets of + 8 to − 16 mm size were prepared in a laboratory disc pelletizer and indurated by varying drying and preheating temperatures in a laboratory Raising Hearth Furnace (RHF). Produced pellets were assessed for physical and metallurgical properties. Improvement in drying and preheating temperature simultaneously helped in mitigating fired pellets’ property deterioration. Drying at 300 °C and preheating at 750 °C helped in the maximum removal of matrix LOI from the pellets before firing and enabled the production of pellets of desired properties. Laboratory scale findings successfully implemented at existing 4.2 MTPA capacity pellet plant of JSW Steel Ltd. Vijayanagar and high LOI iron ores (IOs) utilised which resulted in reduction of average monthly pellet fines generation by ~2 wt. %.

Jun 4, 2022

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By Randall C. Divito, Craig R. Eckdahl, Bruce D. Wagener, Joseph Klejwa

The existing Central City Tunnel was built primarily in the 1930s with a small portion as old as the 1880s. It conveys stormwater in downtown Minneapolis. It is a 4,400-ft long tunnel located 80 feet underground. The Central City Tunnel has experienced surcharging and surface overflows during heavy rainfall events. This paper presents the details of tunnel and shaft design for the new Central City Parallel Tunnel to mitigate the overflows. The design considered hydraulics and geotechnical engineering for the structural geologic conditions including the weak Saint Peter Sandstone and overlying strong Platteville Limestone. Ground conditions resulted in tunnel designs including large flat-back box tunnels and unique cathedral-shaped tunnel sections.

Jun 13, 2023

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023

By Manchao He, Xiaoding Xu, Yubing Gao

Based on the geological conditions of the 15,600 working face in Pingba Mine, this paper establishes the mechanical model of the stress distribution in the pre-working face under the influence of mining pressure based on a hemispherical stress distribution theory. The analytical formula for the stress distribution is determined. A numerical model for the mining pressure under the influence of key layer is also constructed, and dynamic stress interruptions under various roof-cutting relief schemes in different horizontal positions are simulated. The stress distribution of the stope under different pressure relief schemes is analyzed and compared with the theoretical results. Results show that blasting roof cutting blocks the transmission of the abutment pressure to the working surface to the coal and rock mass in front of the working face, reducing the significant working face mining pressure influence range, which decreases as blasting pressure relief position moves toward the working face. Stress accumulation in the coal in front of the working face also increases as the blasting pressure relief position moves toward the working surface. Engineering practice results show that blasting cutting can effectively block the propagation of mining pressure, and the stress impact range is shortened by approximately 1/3.

Jul 31, 2021

By J. D. Miller, C. L. Lin

From mine to mill, the 3D characterization of particles ranging in size from meters to micrometers is now possible. A brief review of X-ray tomography for mineral processing is given with recent advances considered, such as high-speed scanning and image analysis procedures to describe important particle properties, including size, shape and composition. Considering these new 3D characterization tools, applications in mineral processing are discussed for high-resolution X-ray microtomography (HRXMT) laboratory analysis of particles ranging from 20 mm to 5 μm, with a voxel resolution of about 1 μm, including (1) multiphase particle characterization by HRXMT and comparison with scanning electron microscopy (SEM), (2) particle damage state as a result of blasting/comminution, (3) liberation characterization to describe expected separation efficiency, (4) exposed grain surface area analysis to explain the flotation of locked particles, and (5) floc size, shape and water content for polymer-induced flocculation. Finally, applications in mineral processing for plant-site analysis using high-speed X-ray computed tomography (HSXCT) are examined, including, for example, coal washability analysis, the analysis of crusher plant products, and the analysis of pebble phosphate products from central Florida. Scanning rates on the order of 1 kg/min for particle sizes ranging from 150 mm to 1 mm are possible, with a voxel resolution of about 100 μm. For coarse particles smaller than 5 to 10 mm, high scanning rates of more than 300 t/h may be possible at a voxel resolution of about 1 mm.

By J. O. Marsden, J. H. Gourdie, J. R. Arnold, J. G. Mansanti

During the testing and design of the Gold Fields' Chimney Creek mine, it was found that a much higher carbon loading was possible with CIC (carbon-in-solution columns) than with CIP (carbon-in-pulp). In an effort to keep the carbon handling minimized, an emphasis was put on forcing gold to the CIC circuit rather than the CIP. After considerable study, it was found that a circuit with two thickeners and an interstage leach would force 90% of the gold to CIC. Computer modelling indicates that the benefits of the hybrid circuit include higher recovery, less carbon handling, fewer leach tanks, and lower reagent costs.

Jan 1, 1990

By M. G. Eiselein, R. A. Smith, C. H. Sheerin

FMC Gold's Paradise Peak Mine was one of the top two producers of mercury metal in North America in 1988 and 1989. As a by-product, elemental mercury is produced from cyanide soluble mercury minerals, primarily to reduce the health risks incurred with the refining of precious metal precipitate containing elemental mercury and mercury amalgams. A discussion of the design, primarily the Merrill-Crowe units, and permitting for the safe production of mercury will be presented. Additionally, laboratory testwork to determine the effect of mercury on reagent requirements in the Merrill-Crowe process will be discussed.

Jan 1, 1990

The mining industry is one of the three pillars of the Namibian economic development, besides tourism and the fishing industry. Generating 20 % of the GDP and more than 50 % of the export income, half of this amount derives from the diamond mining industry. In 2008, the annual production of 2.2 mio carat achieved an income higher than 1.44 billion Namibian Dollars (more than 750 mio Euro). After the global recession in early 2009, which also caused a significant downcrease in production to only 0.93 mio Carat, the diamond mining industry easily restored itself and the production figures for 2010 are expected to be even higher than those achieved in 2008. Compared to other diamond producing countries, Namibia is mainly producing diamonds of highest quality (jewellery quality), with less than 10 % of the mined diamonds not falling into this category. This high quality stands also for the worldwide highest prize achieved per carat. With 370 $US per carat it is more than four times higher than that of the average South African stone. In 1908 the finding of the first diamonds in the Namib desert close to the coastal town of Lüderitz was reported by a Mr Stauch, railway inspector for the then German colonial railway company. This event immediately triggered a Diamond Rush and subsequently the set-up of the restricted diamond mining area ?Sperrgebiet? through the German colonial administration. In 1913, only five years after the first mining operations had started, the steadily increasing production allowed for more than 20 % of the diamond production worldwide. After the First World War, the new South African government concentrated all mining activities in one organization, CDM (Consolidated Diamond Mines of South West Africa) which in following decades conducted an extensive and detailed exploration of the whole Sperrgebiet and started numerous new diamond mining operations.

Jan 1, 2011

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By M. B. Haggerty, R. J. Sheets, F. Abbasy

To address coal refuse tailings storage needs for a mine operation in western Canada, a feasible solution was to convert excavated open pits into tailings cells. A slope stability investigation and design study were completed to determine the necessary width and slope geometry for in-situ native plugs as the impoundment embankment. The native plugs separate the previous open pit from the current active open pit. This configuration allows for the deposition of refuse tailings in the previous pit while allowing mining to safely continue “downstream” of the temporary impoundment. As mining progresses, each subsequent pit will be filled with refuse tailings; thereby, buttressing the upstream slope of the previous native plug. Although these cells are excavated, and the timeframe for downstream exposure is relatively limited, the native plugs are classified as dams and must be designed to meet applicable safety of dam standards since they impound water and tails above mining personnel in the subsequent open pit. The presentation and paper will discuss the investigation and analysis conducted to develop the geotechnical and hydrogeological design recommendations.

Mar 2, 2022

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

By Lon Santis, Gregory M. Rumbaugh, Christopher Mark

This paper examines the relevant theory, experience, and past practices relating to development mining near gas or oil wells. It addresses setback distance for both coal and stone room-and-pillar mining. This study also involved a review of accident reports involving well interceptions and downhole well surveys. It provides technical considerations for decisions regarding safe setback distances for development mining throughout the United States. The study’s scope is limited to mining near active or inactive (i.e., non-producing, abandoned or inadequately plugged) wells with known surface locations.

Jun 25, 2024

By Stanisław Lasocki

We present an algorithm to integrate the uncertainties of mean activity rate and magnitude cumulative distribution function in the interval estimation of the primary seismic hazard parameters: the exceedance probability and the mean return period. The algorithm is applicable for both the parametric and nonparametric modeling of magnitude distribution. When the Gutenberg-Richter relation-based parametric model of magnitude distribution is used, the interval estimation of its parameters is based on the asymptotic normality of the maximum likelihood estimators. When the nonparametric kernel estimation of magnitude distribution is used, we apply the iterated bias-corrected and accelerated method for the interval estimation, based on the smoothed bootstrap and second-order bootstrap samples. Previous studies indicated that the uncertainty of mean activity rate significantly affects the interval estimates of hazard functions only when the activity rate is low and the inference period is not long (Orlecka-Sikora & Lasocki 2017). With increasing mean activity rate, the uncertainty of magnitude distribution dominates over the uncertainty of mean activity rate in the aggregated uncertainty of the hazard functions. The provided algorithm is generic and can be applied to capture the uncertainty of any multiparameter function from the uncertainties of its parameters. Here we present a further development of the algorithm developed by Orlecka-Sikora & Lasocki (2017) by presenting its implementation in the Traffic Light System approach. As an example of use, we present the confidence intervals estimation of hazard parameters for the datasets related to induced seismicity accompanying underground exploitation of copper ore in the Legnica-Głogów Copper District (LGCD) in Poland. The algorithm is under implementation to the EPISODES platform (https://tcs.ah-epos.eu/) - an IT platform that provides access to integrated research infrastructures of the Thematic Core Service of Anthropogenic Hazards (TCS AH) of EPOS (European Plate Observing System). The algorithm is also a component of the pilot developed within the EPOS SP project (No 871121), which aims to strengthen the interaction with the private sector and the added value for society. The pilot demonstrates the potential of the IS-EPOS platform software applications for the technology-related probabilistic assessment of time-dependent seismic hazard. The pilot supports a Traffic Light System approach. The current seismic hazard is compared to threshold values based on the exceedance probability for a given magnitude.

Apr 26, 2022

"Twin Creeks is a gold mining complex that is part of Newmont’s Nevada operations. The mining complex is composed of two openpits, Mega and Vista, external ore sources and a set of existing stockpiles, all of which provide ore for an autoclave, an oxide mill and a heap leach. Mega pit provides sulfide ore for the autoclave, whereas Vista pit provides oxide ore for the oxide mill and the heap leach. Both pits operate the same mining equipment and their extraction sequence must, therefore, be optimized simultaneously. Stringent blending requirements are associated with the operation of the autoclave for the sulfide ore. Strategic blending optimization on a large scale has brought significant value to the operation by increasing synergies. This paper presents the implementation of a stochastic optimization framework for the long-term production planning at Twin Creeks that simultaneously optimizes mining, stockpiling, blending and processing decision variables. The uncertainty and variability associated with the different sources of material are incorporated in the optimization model by means of stochastic simulations. The stochastic solution generated shows substantial benefits by increasing forecasted recoverable gold, leading to increased cash flows, while reducing the risk of not achieving forecasts by increasing the probabilities of meeting production and blending targets.IntroductionMine operations consist of multiple components such as mineral deposits, stockpiles, external sources, mills and autoclaves. These components represent a mineral value chain, also known in the literature as a mining complex (Montiel and Dimitrakopoulos 2015; Goodfellow and Dimitrakopoulos 2016). The material extracted from the mines flows through the different components and is transformed into sellable products. This flow of material in a mineral value chain involves complex, nonlinear transformations that render the use of industry-standard optimizers difficult. Furthermore, the optimization of a mining complex can be formulated as a mixed-integer, nonlinear optimization program with millions of integer variables representing mining, blending, stockpiling and processing decisions, prohibiting the use of conventional nonlinear optimization approaches. Previous methods that consider the joint optimization of multiple components of the mineral value chain are available (Hoerger, Seymour and Hoffman, 1999; Chanda, 2005; Stone et al., 2005; Wooller, 2005; Whittle, 2007, 2010; Bodon et al., 2010). Although these methods add value by increasing the synergy between the different components of the mining complex, they rely on simplifying assumptions that constrain their efficacy, while ignoring a most critical aspect. The latter aspect includes the geological uncertainty and actual variability of the materials in the mineral deposits mined and are supplied to the related mineral value chain, similarly to conventional life-of-mine planning methods used for individual mines (Dimitrakopoulos, Farrelly and Godoy, 2002; Godoy and Dimitrakopoulos, 2011; Spleit and Dimitrakopoulos, 2017). Additional simplifying assumptions may include: the consideration of a limited number of components, the combination of different methods, the aggregation of variables, fixed production schedules the definition of policies prior to optimization, such as cutoff- grade definition or destination of mining blocks, the linearization of nonlinear transformation functions and/or the disregard for the uncertainty of several critical parameters (Whittle, 2007). The simultaneous optimization of multiple components of a mining complex was introduced by Newmont. Hoerger, Seymour and Hoffman (1999) implemented a mixed-integer programming formulation to optimize Newmont’s Nevada operations. The model is based on the work of Urbaez and Dagdelen (1999) and simultaneously optimizes the extraction of materials from multiple deposits and the delivery of ore to multiple plants, as well as as"

Dec 1, 2018

By T. Yukimasa

Hachinohe smelter, a zinc-lead blast furnace complex with the annual capacity of zinc plus lead of 100,000 tons, had originally treated normal zinc and lead sulfide concentrates. However, it is currently handling a great variety of raw feeds ranging from complex sulfides to oxidic recycled materials in view of resource economy, most of which are unsuitable for zinc electrolysis. This paper reports on some significant efforts recently carried out on improving sintering operation, i.e., the increasing use of secondaries against harmful ingredients like halogens, and the substantial reduction in energy use as the results of various modifications and improvements.

Jan 1, 1982

By Richard J. Wilson

The importance of coal as a major source of energy used by the steel industry has been increasing due to the gradual changeover from steel- making by the open hearth process to steelmaking by the basic oxygen process. Since the production of steel by the BOF process increases the demand for hot metal, there is a growing need to ensure the supply of coke required for the production of hot metal. Coal used for cokemaking has become, therefore, an increasingly important raw material for the steel industry in recent years. Our current projections indicate that coal will be the source of 71% of the total energy requirements of Inland Steel Company in 1985. As a result of the energy shortages of the last few years, various conservation programs have been initiated by the steel industry to reduce the consumption rate of fuel. The efforts to conserve energy have been successful to a great extent due to the rapid advances made in the technology of ironmaking that facilitated gradual reductions in the quantity of coke used per ton of hot metal produced in the blast furnaces. The decrease in the consumption rate of coke was made possible by the use of improved raw materials, such as iron ore pellets and fluxed agglomerates, the operation with high blast temperatures, the injection of auxiliary fuels, and the enrichment of the blast with oxygen. It is expected that additional reductions in the fuel consumption rate will be possible in the ironmaking operations of the large blast furnaces that are being equipped with facilities for proper burden distribution and for operation with higher blast temperatures at high top pressure. The purpose of this paper is to show the effects of coke quality on the production of BOF steel. The importance of coke quality will be pointed out by discussing the effects of the physical strength of coke on both the blast furnace productivity and the steelmaking operations of an integrated steel plant, such as Inland Stee1 Company.

Jan 1, 1980