Search Documents

By Arthur Grounds

Historical In the course of a paper which is necessarily limited in length, such as the present one, it is obviously impossible to describe in detail the history, development, and present position of coal preparation in Western Europe. Great Britain has been blessed with large deposits of excellent coal of nearly every type, ranging from the high-grade anthracites of South Wales, which are characterised by their very low ash and volatile con-tents, to the superb coking coals of South Wales and Durham -probably the finest in the world -with their low ash and sulphur contents, the latter constituent often well be-low l per cent. Gas coals abound in Lancashire and Yorkshire, while coals from the East Midlands, Northumberland, and Scotland are excellent for steam-raising and other industrial purposes. The excellent quality of these various coals has, in years gone by, ensured ready .sales abroad and it is not surprising, therefore; that methods of coal preparation were largely developed on the Continent in an endeavour to upgrade the inferior fuels found there, so that the prepared product could compete with British coals on the European market.

Jan 1, 1951

By K. B. Young

Possibly the most complex fatigue problem associated with the development of the axial-flow 'gas turbine is discussed in its broader aspects from the metallurgical viewpoint. Reference is made to nodal patterns, interference diagrams, etc. The use of such data in analysis of a turbine :blade failure is illustrated. Special attention is given to the influence of some metallurgical variables affecting fatigue strength and, in particular, heat treatment is shown to have a pronounced effect on .the relative fatigue and creep strength properties of a nickel-chromium-cobalt base alloy suitable for turbine blade applications.

Jan 1, 1958

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By M. Mahfoud

The effect of grain refinement on the tensile and fatigue crack propagation behavior of sand cast magnesium alloy AM60B has been investigated in the present study, C2Cl6 in the amount of 0,3% was used to grain refine the melt, The fracture toughness tests were conducted in laboratory air at room temperature (25°C) using a sine-wave cyclic frequency of 20Hz and a load ratio of R = 0,1, The response in the Paris's regime and the critical stress range were determined, Preliminary findings have shown that C2Cl6 has a significant effect on both the tensile properties and fatigue crack propagation of the alloy tested, Grain refinement increased both the yield and ultimate tensile strength by more than 46%, and decreased the crack growth rate from 2,7 to 1,4 MPa Vm , However, the grain size seems to have a smaller effect on threshold stress intensity factor range. The fracture surfaces of specimens were examined optically and under the scanning electron microscope (SEM) to determine the relationship between grain size and fatigue properties.

Jan 1, 2005

By S. J. Laskowski

In potash ore flotation, carried out in NaCI-KCI saturated brine (about 6-7 molar KC1 and NaCI solution), long-chain primary amines are used as flotation collectors. Long-chain primary amines are poorly soluble in water and their solubility further decreases at high electrolyte concentration. For ionic surfactants there is a characteristic temperature (Krafft Point, KP) below which their solubility is too low for micellization. In a previous study, the effect of pH on the KP of dodecylammonium chloride in water was determined [Q. Dai and J.S. Laskowski, Langmuir, 7, 1361-1365 (1991)]. This paper deals with the effect of electrolyte concentration on the KP of dodecylammonium chloride. The derived theoretical relationship between the KP and the critical micelle concentration (CMC) for dodecylamine can be used to calculate the KP for electrolyte concentrations of up to 0.5 mol/L (about 8% NaCI-KCI brine). A simple experimental procedure for the determination of the KP for higher electrolyte concentrations is also described. The results show that the Krafft point of dodecylamine increases from about 17-18°C (in distilled water) to about 80°C at 16% brine saturation.

Jan 1, 2006

By H. Hamza

Efficient and effective management of extraction process tailings is an essential ingredient for the continued success and development of Alberta's vast oil sands resources. Open-pit oil sands operations north of Fort McMurray recover bitumen from flotation circuits. Process tailings are managed in carefully engineered and monitored external tailings management facilities and in below-grade mine pits. In order to support reduction of production costs and improve upon established tailings management practices, CANMET has been working with the oil sands industry in a collaborative framework to assess the potential to integrate thickened tailings into oil sands extraction process flowsheets. Albian Sands has commercialized the process while others, including Syncrude Canada Ltd., continue to evaluate the suitability of the process for their operations. This paper provides an update on R&D work undertaken in recent years to assess and develop the potential of thickened tailings technology for the open-pit oil sands operators of northern Alberta. The aim of this work was to explore opportunities to optimize process efficiency and environmental sustainability by improving water and energy conservation and develop more alternatives for tailings management and reclamation.

Jan 1, 2004

By R. B. Hyde

"Severe drilling conditions and difficult mud problems are briefly out-lined as the major cost items in all production operations. The chief problems discussed are abnormal pressures, high temperature, trouble-some shales, and low rates of penetration. These problems have been eliminated or greatly reduced in many areas by• the proper application of recently developed drilling mud products and techniques. These severe problems and their solutions are discussed generally: the application of high-density weighting materials to overcome abnormal pressures; surfactant muds with sodium polyacrylate as a solution for deep and high-temperature drilling; shale control muds and new dispersants for severe shale problems; and low-solids emulsions and •extreme-pressure lubricants for greatly improved rates of penetration."

Jan 1, 1959

By I. R. Jonasson, R. W. Boyle

"Current interest in the distribution of mercury in the natural environment comes from quite different, though not unrelated, sources. Mercury has long been an important metal in many industries and has, therefore, been much sought after by mining interests. The presence of mercury traces in the various media of the natural environment, namely soil, rock, air, water and vegetation, is exploited by geochemists not only to find mercury and polymetallic ore deposits, but also to find most other types of economic metal mineralization. More recently, however, mercury has caught the attention of health authorities and environmental scientists who are becoming increasingly concerned over the hazards of mercury wastes and the danger these present to the environment and to man. It is now apparent that the trace quantities of mercury, considered so important and helpful to exploration geologists, can be concentrated in the biosphere to such levels as to present considerable problems for ecologists. This article summarizes most of the available data on mercury contents in materials of geological interest and presents average normal values for rocks, ores, minerals, soils, sediments, waters and plants. The geoch.emical cycle for mercury in nature is presented and the mechanisms of mercury migration around the cycle are discussed."

Jan 1, 1972

By A. Ignatieff

"Demonstrations of Automatic Coal Burning EquipmentAT THE 1951 and 1952 Annual Coal Research Conferences sponsored by the Dominion Coal Board and attended by delegates from the Dominion and Provincial governments as well as industry, the importance ,of encouraging the co-operative interest of Canadian coal and equipment industries in •promoting the use of equipment types best suited to burn given Canadian coals was emphasized. It. was suggested that this idea •be enlarged upon at forthcoming C.I.M. meetings that would be .attended largely by coal mining engineers.With this in view, a Domestic Heating Forum (1) was featured in the Coal Division programme at the 1951 Annual Western Meeting of the Institute in Calgary, and a much more ambitious programme, highlighted by live demonstrations, was •staged at the combined Annual Western Meeting and Fourth Meeting of District 4 held in Winnipeg in October 1952.With the excellent co-operation of a number of equipment manufacturers and coal companies, and with facilities kindly provided •by the University •of Manitoba authorities, burning demonstrations were• arranged in the Agricultural Engineering Building, on October l 7th. These demonstrations were a fitting sequel to the Coal Division sessions held in the Royal Alexandra Hotel on October 16th, at which the combustion of coal was specially featured in a series of papers by prominent Canadian and United States specialists.The primary purpose of the demonstrations was to •show that all coal, regardless •of rank, can be satisfactorily used provided that proper application is made with equipment suited to its purpose."

Jan 1, 1953

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By Warren A. Sheaffer

THE chief uses for copper are as a conductor of electricity and as the chief component in brasses and bronzes. For such uses, the copper must be of very high purity. H the impurities are zinc, iron, lead, arsenic, or antimony, they can be removed to a great extent by fire-refining. H, however, gold, silver, nickel, or cobalt are present, electrolytic refining is necessary. Electrolytic refining must be preceded by fire-refining and hence all impure copper must be fire-refined. The electrolytic refining of copper is most efficiently carried on when the impurities in the anodes are at a minimum. Some of the impurities tend to deposit with the copper at the cathode, while others remain in solution, decreasing the conductivity of the electrolyte and thus increasing the voltage necessary for refining. Since these dissolved impurities must be removed by continuous purifications, the amount of impurity in the anode copper should be reduced by furnace refining to some predetermined limit. Anode furnace operation aims to reduce these impurities to a minimum beyond which the cost of further furnace refining would exceed that of removing the remaining small amounts of impurities from the electrolyte. The anodes should have a fine-grain internal structure because any pieces of metal becoming detached from the anode during the electrolytic refining are inconvenient to remove from the cells and may cause short-circuits. Impurities tend to disrupt such a structure and thus form zones of weakness during corrosion. When the impurities are reduced to a satisfactory mini-mum, the anode, due to having a fine-grain structure, will corrode uniformly over the entire surface area exposed to the electrolyte. Oxides of the impurities may be volatile, in which case they pass off as flue gases, or they may form viscous slags having a lower specific gravity than molten copper, thus permitting their removal by skimming. Some impurities can be oxidized by introducing air into the bath. Due to the large solubility of oxygen in molten copper, oxygen is distributed uniformly throughout the bath and thus comes into intimate contact with all impurities. The oxides which are insoluble in molten. copper are removed either as flue gases or as slag.

Jan 1, 1942

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By A. D. Huffman

This paper covers the major salt deposits of Canada, with a brief summary of the early history of the industry and a more extended outline of progress since the second world war. Both dry mining and solution mining are covered, and the future of salt mining in Canada is discussed.

Jan 1, 1968

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977

By Arthur Notman

Since addressing the Institute a year ago on The Future of the Copper Industry (l), many things have happened, most of them bad. It has been a hard year for profits and prophets. It was, therefore, with consider-able perturbation that I accepted the gracious invitation of your Committee to reappear. On reviewing my remarks of a year ago, I. have wondered whether, under pressure of more important matters, the Committee had neglected to make a note of them, or whether they felt that further explanations from me were in order. In either event, I am glad that I am here and welcome the opportunity to make any contribution I can to a clearer understanding of the problems of copper to those concerned. The English-speaking nations own 80 per cent of the present world-production of the metal. Col. P. E. Barbour, Secretary of the Mining and Metallurgical Society of America, and I recently completed an estimate of the known world resources of copper. We placed the figure, in round numbers, at 100,000,000 tons of metal. Of this amount, about one-third lies in the United States, one-third in the British Empire, and one-third in South America; and all but 4 per cent of this is owned by British Empire and United States capital. Our figures do not include any estimates for Russia, Japan, or Europe, on which there are no available data. It is true, consequently, that the British Empire and the United States are the ones concerned. It seems to me to be a matter of great importance to the world at large, and of even greater importance to those nations themselves, that the known sources of supply of this metal, so essential both in peace and war, rest so strongly in their hands. I cannot believe that in the long run they will neglect their responsibilities in the wise administration of these resources.

Jan 1, 1932

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976

By Da-Qiang Cang, Qingde Wang, Wei Wang, Wen-Bin Dai, Min Guo, Yu Li

Utilization of both slag and its heat for hot slag is a great challenge for iron and steel industry. Many methods of hot slag modification for directly converting hot slag into value-added materials were researched in recent years, and waste heat of hot slag could thereby be transformed into inner energy or chemical energy of the materials. In this paper, an experiment of converting hot slag directly into glass ceramics by hot slag modification method was conducted. A cooled modifiers mainly composed of fly ash were firstly heated though a cyclone furnace and then fell into a molten bath to mix with hot steel slag. Half of hot slag was used as raw materials and accordingly about half energy consumption, about 5MJ/kg for melting raw materials was saved in the process compared with that of traditional producing method. Frit quenched from the modified hot slag had a higher basicity of 0.6-0.7 than traditional frits in order to reduce the needed amount of cold modifiers and accordingly utilize more hot slag and its waste heat. Glass ceramics were further prepared from the frit and a heat treatment of one-stage method is more suiter to such frit than that of two-stage method. The glass-ceramics with basicity of 0.6 and heat-treated by one stage method had the best performance with bending strength of 146.46 MPa, Vickers hardness of 6.79 GPa, water absorption rate of below 2% and shrinkage rate of around 10%.

Jan 1, 2015

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

The world’s first copper electrorefinery started production in 1869 at Burry Port in South Wales. Built within the Pembrey Copper Works which had commenced smelting operations in 1849, the new refinery was based on principles described in the British patents issued to J.B. Elkington in 1865 and 1869. Refining principles and practices pioneered there were key to the foundation of modern electro-refining practice in what is now a dominant international industry producing over 16 Mt of electrical grade copper annually. This paper explores the background to this pioneering application of the new, early 19th century, science of “electro-metallurgy” and examines its links to the contemporary decorative electro-plating industry and to the shortcomings of 19th century fire refining. The beginnings and early years of the Pembrey electrorefinery are briefly discussed in relation to the quality, applications and pyrometallurgy of copper at the time. More than a decade would elapse before the birth of the electrical age: the Pembrey refinery may be seen as one of its vital precursors. Note: This paper was originally published as part of the Copper 2013 proceedings (A.E. Wraith, P.J. Mackey and J. (formerly R.) Protheroe Jones, “Origins of Electrorefining: Birth of the Technology and the World’s First Commercial Electro-Refinery”, paper in Electrorefining, Vol. V, Book 2, (Eds. R. Abel and C. Delgado), Cu 2013 International Conference, pp. 19-33, IIMCh, Santiago, Chile, 2013). It is reproduced here together with a new Appendix and supporting references that lists the year of commencement of the first electrolytic copper refinery by country, 1869 to 1956. It all, the year of the first electrolytic copper refinery established for 15 countries is included. These 15 countries now produce more that 70% of world refined copper (for 2018). INTRODUCTION In the 1840s, the new science of ‘electro-metallurgy’, a term coined by Smee in 1841 (Smee, 1841), was being adapted to the decorative electro-deposition of silver in a thin, bright adherent coating that was evidently equal in appearance to traditional silverware (Williams, 1976). Chief among innovative manufacturers of decorative objects who took up the new art of silver electro-plating was the acclaimed firm of G.R. Elkington and Co. of Birmingham, England. The company, which vigorously developed all aspects of electro-metallurgy for the decorative trade, entered the field of ‘electrotyping’, a technique in which the surface features of a mould are copied on an electro-deposited copper layer which, when stripped off, can be used to reproduce an imprint of the mould. In essence, it is a form of casting by electrodeposition, invented in 1837 independently by Jacobi in Russia (Pavlova, 1968) and Spencer in England (Wyatt, 1851).

Jan 1, 2019