Search Documents

By R. J. Fruehan

The oxygen activity and concentration were measured in Fe-Cr-0 melts in equilibrium with an oxide phase at 1600°C (2912°F). The activity was determined by ,use of the following solid oxide -electrolyte galvanic cell CY-Cr8,(s) I ZrOz(CaO) I Fe-CY-G(saturated)(l) The oxygen concentration decreases with increasing Cr concentration to about 270 ppm 0 at about 7pct CY and then increases gradually. The activity coefficient of oxygen (fo) decreases with increasing Cr. In melts containing up to about 20 pct Cr, log f is approximately a linear function of wt pct Cr with a slope (e q 2) of —0.037. The activity of chromium was calculated and found to exhibit a small negative deviation from Raoult's law. From the activity and solubility data for low chromium melts, the free energy of formation of chromite, FeCr204, was found to be -79.8kcal per mole where pure liquid chromium and oxygen at I wt pct in Fe are the standard states. ThE effect of chromium on the chemical behavior of dissolved oxygen in liquid iron is of great importance in controlling the deoxidation of steels containing a significant amount of chromium. Chen and chipman' equilibrated Fe-Cr melts in the presence and absence of slag with hydrogen-water vapor mixtures. They concluded that at 1595°C chromite was the oxide phase in equilibrium with Fe-Cr alloys containing less than 5.5 pct Cr while at higher chromium concentration Cr,O, was the stable phase. In the composition range 0 to 10 pct Cr they found that the interaction coefficient, was equal to -0.041. Turk-dogan,' Schenck and Steinmetz,, and pargeter4 measured egr) in a similar manner and found the value to be -0.064,-0.04, and -0.052, respectively. McLean and Be11 evaluated egr) from their data on the equilibrium of Fe-Cr-Al-0 alloys with H2/H20 mixtures and found it to be -0.058. However, McLean and Bell's value should only be considered an estimate because the effect of aluminum on the activity coefficient of oxygen is about a hundred times greater than that of chromium. Consequently, an error in the value of egl) used, which at the present time is not well-known, or an error in aluminum analysis, which is present in very small quantities, will result in a significant error in egr). Fischer et a1.6 determined the interaction coefficient (eEr) in Fe-Cr-0 melts not in equilibrium with an oxide phase and containing less than 18 wt pct Cr at 1600°C electrochemically. They determined a value of -0.031 for egr). Hilty et aL7 measured the oxygen content of Fe-Cr melts in equilibrium with an oxide phase containing up to 50 pct Cr. They found that the solubility of oxygen decreased as the chromium content increased to about 6 pct Cr and then increased gradually. They concluded that the equilibrium oxide phase was chromite below 3 pct Cr, distorted spinel from 3 to 9 pct Cr, and Cr,04 above 9 pct Cr. Adachi and lwamotoa also investigated this system, but did not find Cr30,. They X-rayed the equilibrium oxide phases and did not find the presence of Cr,O,. They also X-rayed the oxide phase extracted from a 65 pct Cr melt which was heat treated and did not find metallic chromium as would be expected if Cr3O4 were the equilibrium oxide phase as indicated by the reaction : 3Cr3O4 — 4Cr2O:, + Cr [lj It was the purpose of the present investigation to determine the effect of chromium on the activity coefficient of oxygen in Fe-Cr melts by measuring the activity and solubility of oxygen equilibrated with an oxide phase in the composition range 0.18 to 50.5 wt pct Cr at 1600°C (2912°F). The activity of oxygen in the melts was determined by use of the following galvanic cell: The relationship between the partial pressure of oxygen in equilibrium with the melt and the reversible electromotive force of the cell (E) is where 11 = 4, F is the Faraday constant, pb, is the oxygen pressure in equilibrium with the meit and is the oxygen pressure in equilibrium with Cr203 as determined from the free energy data compiled by Elliott et al? The oxide phase in equilibrium with pure chromium was assumed to be Cr If Cr30, were the equilibrium phase the activities derived would be approximately the same, since the best estimated free energy of formation of Cr,O,, if it does exist, is approximately % the free energy of formation of The activity of chromium in Fe-Cr alloys at 1600° C was also determined from the measured electromotive force. The activity of chromium (aCr) is related to the electromotive force as follows: , The oxide phase in equilibrium with pure chromium and Fe-Cr melts from 10 to 52 pct is assumed to be Cr203 so that n equals three. If future work proves the existence of Crs04 in equilibrium with Fe-Cr melts and pure chromium, the experimental results can be reevaluated using a value of $ for n in Eq. 141. A value of ^ for n will make the activities about 10 pct higher. In order for Eqs. 131 and [4J to be valid the electrolyte, ZrOa(CaO), must exhibit predominantly ionic conduction at the temperature and oxygen partial pressure of its use. Previous work1' has demonstrated that ZrOz(Ca0) is predonlinantly an ionic conductor

Jan 1, 1970

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

By G. B. Gould, F. M. Gibson

IN DECEMBER, 1934, the joint Committee on Fuel Values, of the American Institute of Minim and Metallurgical Engineers and the American Society of Mechanical Engineers, submitted a preliminary report, which briefly stated its conclusion that it was not possible to devise any formula for the valuation of coal, based upon the various physical and chemical properties, that would be generally applicable. That report also listed those chemical and physical properties of coal that are generally recognized to have some effect on its use in steam plants, and those physical characteristics of steam plants which affect, in one way or another the relative importance of the properties of coal used in them. Since then, the Committee has considered and discussed in greater detail the interrelationship of the properties of coal and plant characteristics. The conclusions of the Committee are summarized below, with certain recommendations regarding engineering procedure, which will promote the collection of more easily correlated observations with respect to this subject, and thus advance more rapidly the accumulation of data capable of general application.

Jan 1, 1936

By Marcus Nadler

WAGES in the United States, in spite of the wage freeze, have increased materially. Overtime payments have become standard practice in almost all industries. Now efforts are being made to place wages on an annual basis, and if this is adopted, it will result in an increase in the cost of production. Organized labor today is more powerful than ever before; union membership is large and steadily increasing, and in many instances membership in the union is a prerequisite to employment. The treasuries of many unions are strong as a result of the large membership and full employment. The unions, therefore, today are in a much better position than ever before to carry on long strikes. Politically, too, the unions are more powerful today than they ever were. On the basis of their strength, one may expect that some of the demands that the labor unions will make in the not distant future will be granted. It is, therefore, quite evident that before long, particularly when the curtailment in war production reaches about 40 per cent, this country will be confronted with a serious labor problem.

Jan 1, 1945

By Louis Ware

BEFORE the war we often heard the term "Big Business." And there were complaints of the ills and abuses attributed to bigness in business. Although there were examples where the small businessmen spoke for their rights and sought protection from the bigger ones, it has only been in recent war years that a tendency has developed definitely to divide the business of our nation into the big and the small. In some cases, those with an eye to the political value of the vastly greater number of small businessmen of the country have fomented this division by hurrying to the protection of these more numerous voters, and intentionally or not have emphasized in their writings and verbal attacks any and all differences of these interests that could either be found or fabricated to, suit the occasion. It has become another example of breaking the people into classes and thus setting up the basis for the claims of one class against another, and the subsequent demand for legislation and Governmental aid. The terms "big" and "small" are purely relative. One businessman, employing a hundred men, told me recently he did not know which adjective would be more appropriately applied to his operation. He did not know whether he should join the small operators' group that had been organized, or should consider himself big. He said that his present plant seemed big to him when he looked back to its humble beginning many years ago with a couple of men in two rooms. Yet, when compared with many of his competitors who employ thousands, his was small. He did add, however, that he probably became big one day a few years ago when the union moved in and organized his employees.

Jan 1, 1945

By William L. Saunders

MANY members of the Institute, who participated in the visit made, during the Bethlehem meeting of February, 1906, to the shops of the Ingersoll-Rand Company, at Phillipsburg, N. J., inspected with interest the new Electric-Air drill, which the company had set up for the purpose of showing it in actual operation to American. mining engineers. At the request of the Secretary of the Institute, I promised at that time to prepare a paper for our Transactions, describing the construction and advantages of the machine. But such a paper would then necessarily have contained much that was only expected or claimed by the designers and manufacturers of the drill, and not yet incontrovertibly proved by varied and long-continued practice. However moderate such statements might have been, they would have given inevitably to the paper, to some extent at least, the air of a prospectus, rather than of a technical contribution. I therefore decided, with the Secretary's approval, to postpone the writing of the promised paper until it could set forth the results of adequate actual practice, as well as the latest details of construction, etc., based upon practical experience. That period has now arrived. The Electric-Air drill has been exhaustively tested in the field, under varied and arduous conditions and upon the hardest rocks. It is now fairly in the field; its merits and performances are matters of unimpeachable record, and its place among established competitors can be definitely determined. As a representative of the Ingersoll-Rand Co., as well as a member of the Institute, I may be permitted to add that my company, being largely interested in the manufacture of air-

Jan 9, 1907

By F. T. Havard

(Canal Zone meeting, November, 1910.) I. INTRODUCTION. THE present truce in litigation between Western smelting and ranching interests gives opportunity for a summary of the results achieved by metallurgists in condensing fume and de-acidifying furnace-gases. In the absence of complete records of past experiments, there has been a good deal of unnecessary duplication of attempts and' failures. Yet, especially under the recent policy of our large corporations, looking to the economic recovery of the values of by- and waste products, original and, in some cases, effective measures have been developed by American metallurgists. In the case of Bliss vs. the Anaconda Copper Mining Co., the Montana Supreme Court, recognizing the progressive efforts made to render the flue-gases innocuous, and the value to the community of the smelting company's operations, refused to hamper its work, and returned a verdict in favor of the defendant. In the trial, the experimental firms of the company in the so-called "affected region" were proved to be thriving perfectly, showing that immunity was guaranteed to vegetation and stock by the wide distribution of the sulphurous acid gas in the dry air of Montana. Indeed, L. S. Austin has proved that by the time the fume is 4,000 ft.. distant from the stack, the percentage of sulphurous acid has been diminished from 2.28 to 0.00045; and Angus Smith has shown that rain must contain 40 parts per million of free acid before vegetation is affected. The arsenic in the stack-gases is but a very small part of the original content of the ore, of which 80 per cent. and over is rejected in the concentrator and furnace waste-products or recovered in the flues. Nevertheless, neither the peace in Montana nor the armistice

Aug 1, 1910

By LIONEL E. BOOTH

ORE tests are made for the purpose of determining the correct methods of treatment for any particular ore. They should be conducted so as to insure that the results obtained in actual mill practice, on ore of similar grade and physical nature, will duplicate the results obtained in the test work. As the expenditure of many thousand of dollars may be involved in the building of the necessary mill, the testing of ores calls for extreme care and skill in handling laboratory machines, and a knowledge of actual practice to guard against the danger of obtaining results in test work that would be impractical to duplicate on a commercial scale. The importance of a correct sample of the ore is at once apparent. No matter with what degree of care the test 4rk is done, it loses its value when made on an unrepresentative sample. It is the first safeguard against future disappointments in the loss of capital and time. A number of failures in the past have been traced directly to faulty or lax methods in obtaining the ore sample.

Jan 1, 1924

By William Paxton Hewitt

Mineral deposits of western Utah and eastern and central Nevada have produced in excess of $8,500,000,000 since 1871. Through 1965, Bingham Canyon had produced over $4,600,000,000 and seven other camps over $100,000,000 each, principally from base metals. In addition, they yield iron and uranium ores; contain the world's largest beryllium reserves; and have produced the United States' most important gold discovery in 25 years. The area is famous for its silver production and its bonanza-type precious metal deposits, but such production has become unimportant. The area's greatest producers of metallic wealth are base-metal deposits in limestones and porphyry-type copper ores. In contrast to silver's decline, gold production has been rising-the result of by-product operations at Bingham Canyon. The area also contains gold deposits in which the gold is so finely disseminated it is not recoverable by panning. The area's gold ores frequently are associated with realgar, cinnabar, and carbon. The ore deposits generally are attributed to Tertiary intrusives,* but, at Mountain City, they may be related to Paleozoic volcanism. Mountain City has yielded rich chalcocite from quartz-pyrite-chalcopyrite bodies in siliceous sediments. Regional stratigraphy and structure are difficult to interpret, 69 per cent of the area being obscured by alluvium or volcanics. In general, central Nevada consists of chert, shale, silty sandstones, lavas, and pyroclastics; eastern Nevada and western Utah of many alternations of limestone, shale, and sandstone. Central Nevada has been structurally active since late Devonian. Although granitic stocks may have intruded eastern Nevada and western Utah prior to the Cretaceous, these areas remained quite stable until affected by the Laramide Revolution. Precambrian exposures, occupying 3 per cent of the area, have not been important hosts. However, the question is raised as to whether Precambrian carbonates, properly situated with respect to invading mineralizers, might yet prove to be important. This paper describes 16 precious metal camps, 6 limestone replacement districts, 2 silver-base metal vein deposits, and 9 miscellaneous types and discusses briefly the 11 * Some ores, as at Ely, are associated with intrusives of. Cretaceous age. major camps that are described in detail in this Volume.

Jan 1, 1968

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential; but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for bringing in a prospect and making it a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is headed by an engineer-promoter who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the final operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1959

By John M. Lovejoy

FEDERAL regulation of the petroleum resources of the nation has long been an interesting topic for discussion. A plan to accomplish Federal control has now taken definite form. At the request of the President of the United States, a bill to be known as the Petroleum Conservation Act of 1939 has been presented to Congress-H. R. 7372, offered by Representative Wm. P. Cole, Jr., and more usually known as the Cole bill. It is an act ostensibly designed to conserve our petroleum resources, through regulation of production practices. Hearings are being held currently by a subcommittee of the Interstate and Foreign Commerce Committee, in compliance with the request of the President to report the bill early in the next session of Congress.

Jan 1, 1939

By Michael J. Messel

OF the various minerals that occur in fibrous form known as asbestos, chrysotile is the variety most in demand for commercial uses, and, last year, over 683,000 tons of the various grades were produced in Canada and United States, exclusive of African and Russian production, which figures are uncertain. Production has not been able to keep up with the increased demand, and an acute shortage exists. Canada, Russia, and Africa are still the most important producers. However, Russia consumes most of its production at home and exports very little. The United States consumes over 60 pct of the total production and produces only about 4 pct of the total from deposits in Vermont and small quantities from Arizona. This paper will review mainly, some of the more recent developments concerned with the extraction and processing of this fibrous mineral for various industrial uses, such as textiles, insulation, building materials and brake linings.

Jan 1, 1949

By Joseph W. Richards

(New York Meeting, February, 1912.) THE Ashio copper-mine of the Furukawa Mining Co. is situated 18 miles from Nikko, and 109 miles north of Tokyo, near the center of Japan. The mine-waters are run over scrap-iron, whereby most of the copper is precipitated as cement copper, leaving iron sulphate with some copper sulphate in solution. After using in the wet concentrating ore-dressing plant, the waste water contains clay and ore-slimes. The only avenue of disposal of this water is the Watarese river; but as this flows through valleys in which the water is used for irrigating the rice-crops, it is necessary to purify and clarify the water before discharge. The water amounts to from 600 to 700 cu. ft. (from 17 to 20 cu. m.) per minute, and averages about 0.00025 per cent. of copper, representing more than 18 tons of copper per month. The water carries H2SO4, FeSO4, Fe, (SO,),, CuSO4 and other metallic sulphates in solution, and clay, ore-fines, slimes and basic. iron sulphates as suspended matters. To purify and clarify the water, precipitation by milk of lime has been used, in three different ways, as follows: I. First Method, Copper not Recovered. Milk of lime was run into the water, and the mixture run through six settling-ponds, and then through a sand filter into the river. Fig. 1 is a view of the settling- and filtering-ponds. In the first pond, sand and metallic hydrates free from copper collected; in the next five ponds, slime, calcium sulphate, and metallic hydrates carrying copper settled out. The effluent carried from 0.1 to 0.05 mg. of copper per liter

Jun 1, 1912

By Herty, C. H.

Three distinct processes take place during the conversion of iron ore to steel. First: the raw ore is reduced to metallic iron in the blast furnace and during this reduction certain constituents are dissolved in the iron, either through the solution of a solid into a liquid phase, as in the case of carbon, or by reduction of an oxide existing in the slag to the metallic element of that oxide, with subsequent solution of the metallic element in the iron. Thus by the process of solution and reduction, a pig iron results which contains about 4 per cent carbon, 1 per cent silicon, 1 to 2 per cent manganese, 0.1 to 0.4 per cent phosphorus, and 0.03 to 0.10 per cent sulfur. To obtain a sufficient yield of iron from the ore it is necessary that the reducing process be carried as far as possible, with the result that the impurities mentioned accompany the reduced iron. Second: to convert this iron into steel it is necessary to oxidize a part of the iron in eliminating the impurities to the extent desired for the particular product being made. In eliminating these impurities by oxidation a certain amount of iron oxide (FeO) dissolves in the steel. This dissolved FeO reacts with the metalloids, except sulfur, and to eliminate them to the desired extent it is necessary to leave a considerable amount of FeO in the metal. The reaction of iron oxide with silicon, manganese, and phosphorus results in the formation of the oxides of these elements. The oxides enter the slag and the extent of elimination of the elements depends on certain equilibria between the slag and the metal. The reaction of FeO with carbon results in the formation of the gases CO and CO, which, after saturating the metal, pass into the furnace gases. Third: after the iron has been purified to the desired extent as far as the elements listed are concerned, it is necessary to deoxidize the bath to remove the FeO, which is the vital factor in gas formation as the steel solidifies.

Jan 1, 1957

Gus C. Henning, New York City: In taking up the discussion of these specifications it is necessary that I give definitions of what I understand under the term " Specifications." There may be three kinds, viz.: (1) Specifications in general; (2) Standard Specifications; (3) Standard International Specifications. 1. A Specification is a document used in commerce which should clearly define the qualities of material to be supplied by the producer, the tests which shall be applied for their determination, and the methods which shall be applied for the purpose of determining that the entire product shall possess such qualities, properties and finish as are desired. The terms used in such document must be applied in accordance with their strict technical definitions as used by those most conversant with them, and the language should be of such accuracy that there can be but a single interpretation of each and every clause. A specification is a part of a contract, and should be legally perfect and accurate. Inaccuracy of definition and dic-

Jan 1, 1903

By E. P. Pfleider

Important economic planning by industries, companies, financial firms and governments is predicated on estimates of future growth potential. Prior to the passage of the Taconite Amendment by the people of the State in November 1964, various admittedly conservative forecasts were made of the future of Minnesota's iron ore industry. Since that date, 3 new taconite plants are under construction, 2 are being expanded, one has just gone "on stream," and a seventh is in the design stage. These plants have a total capacity of about 35 million tons of pellets annually. The pessimism of 1964 today is being replaced by unbounded optimism. In the light of such recent developments, it becomes essential to update forecasts related to production, employment and capital investments. New projections show 50 to 58 million tons of pellet production from Minnesota by 1975. This tonnage, together with some 6 to 8 million of natural ores, should provide an annual full-time employment of 15,000 by the mining companies, plus 700 in related railroad and power producing activities and 1000 in plant construction. Total capital investment in new plants should reach $1.5 billion by 1975 and $2 billion by 1990. These current estimates indicate that the conservative goals as set in 1964 for the year 1990 should actually be achieved by 1975 or 1980. BACKGROUND Various forecasts1,2,3 have been made of the future consumption and production of iron ores within the United States. The most recent of these is by Harrison,1 delivered at the American Mining Congress meeting in Las Vegas in October. His estimates reflect the latest iron ore developments on a world wide front as well as the accelerating trend toward pellets. Minnesota's Natural Resources council prepared a detailed report in 1964 outlining the various factors that affect the future of Minnesota's iron ore industry. It presented estimates predicated on the

Jan 1, 1967

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By Robert S. Williams

NO new ferrous alloys have been produced in the last five or six years that are as outstanding contributions to civilization as were the high-speed steels of the early part of the century or the stainless steels announced at the close of the World War. There have been, however, many developments of major importance having to do either with modifications of existing alloys or with new methods of treatment of older iron or steel alloys. Only a limited number of these new developments can be discussed and their selection does not necessarily imply that these are the most important but merely that they are of general interest rather than perhaps of greater importance in highly specialized fields.

Jan 1, 1939

By G. K. Manning, P. C. Rosenthal

USE of copper as an intentionally added alloy in steel and cast iron has rapidly expanded with-in the last fifteen years. It is estimated that in 1931 not more than 2000 tons of copper were so used; by 1941, however, this figure had grown to 13,000 tons. Tonnage figures during the war years have been restricted just as copper itself has been restricted, but copper-bearing cast irons and steels have played a part in the production of ordnance equipment. They are used in gun carriages, airplane landing-gear assemblies, scout cars, bulldozing equipment, army trucks, armor plate and many other instruments of war. These wartime applications have their counterpart in many peacetime applications; derricks, dredges, mine equipment, railway equipment, trucks, farm implements, automobiles, and tractors, all usually contain some parts made of copper-bearing steel or iron. An example of this is the Ford tractor which in 1940 contained over 300 lb. of copper-bearing steel castings. To this list should be added corrugated building sheet for exterior use most of which, at the present time, contains upward of 0.15 per cent copper. With the return to peacetime economy and the removal of wartime restrictions, it appears certain that copper cast irons and steels will find increasing application in civilian goods.

Jan 1, 1945