Search Documents

By André Mans, Frans B. Waanders

Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof. A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process, which resulted in the liberation of Fe and subsequent formation of an oxihydroxide froth. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought.

Jan 1, 2003

By André Mans, Frans B. Waanders

"Ferrosilicon (Fe-Si) is an important commercial material and it forms the basis of the powder used in dense medium separation (DMS) of various minerals in a minerals beneficiation process. Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof.A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. The SEM analyses of the Fe-Si yielded a composition of 15 wt.% Si and 85 wt.% Fe with minor impurities of Mn and Cr (<1 wt. %), resulting in an ordered phase with a calculated composition of Fe2Si. The average density of the Fe-Si was found to be 7.177 g.cm-3 whilst the size distribution was determined with the d50 of the particles being approximately 30 µm. A slurry, containing 10% solids was prepared, which had a density of about 1.1 g.cm-3 and this slurry was used to conduct the various experiments under laboratory conditions at the university. Samples were taken at regular intervals from a storage container containing a lime solution as well as from a closed circulation circuit system, kept at a constant temperature of about 60°C. Mössbauer Spectroscopy yielded, for the new fresh Fe-Si-samples, a two-sextet spectrum with hyperfine magnetic field strengths of 19.9T and 30.7T respectively, and the yellow-brown froth was found to be akaganeite or ß-FeOOH.It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought."

Jan 1, 2003

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By A. N. Lazaridi, S. I. Afanasenko, S. A. Safonov

"This scientific work presents the results of comparative tests of centrifugal concentrators with a vertical and horizontal axis of rotor spinning. The article also describes a qualitative analysis of the behavior of mineral particles in a centrifugal field with fluidization for concentrators with a horizontal axis. The analysis was aimed at studying the effect of the quantity of fluidization holes in the basket on the degree of magnetite recovery and the effect of the basket rotation speed. The experiment demonstrated that concentrators with a horizontal axis are not inferior in terms of the qualitative recovery indicators to concentrators with a vertical axis. The researches also provided facts about the wide practical application of concentrators with a horizontal rotor arrangement. INTRODUCTION Methods of gravity concentration, attractive for their ecological purity, see their revival. First of all, this is due to the invention of centrifugal concentrators with the fluidization of the layer of mineral particles. The creation of a new generation of gravitational centrifugal concentrators made it possible to achieve a tangible breakthrough toward the direction of reducing the grain size of mineral particles effectively divided by density, up to 10 µm at a high production capacity of the vessels reaching 500-600 tons per hour. Such separators enable dressing a crushed ore of flotation grade and in some cases replace the flotation process, especially in primary operations, in joint cycles. In the long term, this method of concentration should significantly expand the scope of application, replace partial flotation processing, ensure the introduction of environmentally friendly energy-saving technologies at ore-processing plants. Summarizing the international experience for the last 30 years, it can be confidently asserted that centrifugal methods of concentration have become widely used in processing schemes for the separation of finely dispersed products in the mining industry. An interest in the creation of installations using centrifugal acceleration for the separation of mineral particles by density has particularly grown. Dozens of centrifugal concentrator designs have been created and continue to be improved. Centrifugal concentrators have a number of obvious advantages, which are especially relevant today. Losses of fine gold during the process of mining are well known. Gold washers screw, spiral separators, jigging machines and sluices traditionally used in the production processes do not solve the problem of fine gold recovery. Table 1 shows the results of comparative tests of a centrifugal concentrator (ITOMAK) and other concentration equipment. According to the research conducted by the company GMRS, Krugersdorp, South Africa (2000), the initial material was gold ore crushed to 150 micrometers (90%)."

Jan 1, 2018

By Z. S. Abisheva

Rare and rare earth metals use quite often is an indicator of national economy development. The world structure of the rare-earth metals manufacturing countries in 2015 was presented as follows: China – 94.2%, India – 2.0%, Russia – 1.8%, the USA – 1.2%, Brazil – 0.5%, Malaysia – 0.3%. In Russia, large reserves of rare-earth metals, which reach nearly 28 million tons, are revealed. Kazakhstan, possessing a raw materials source of rare-earth metals, has all prerequisites for development of branch. Rare metals are manufactured in Kazakhstan incidentally by non-ferrous metals production. The production of indium, thallium, cadmium, selenium, tellurium, bismuth is made at the Ust-Kamenogorsk lead plant; tantalum, beryllium, niobium and molybdenum – at the enterprises of “National Atomic Company Kazatomprom” JSC. Production of a titanium, magnesium and vanadium is adjusted on “Ust-Kamenogorsk Titanium-magnesium Plant” JSC. Capacities for beryllic production yield are available on “Ulba Metallurgical Plant” JSC. The main producer of perrhenic production and osmium-187 is "Zhezkazganredmet" RSE. The single producer of gallium in Kazakhstan is “Aluminium of Kazakhstan” JSC; the capacity of enterprise is 25 t a year. In Kazakhstan innovative technologies for rare and rare earths mineral raw materials processing are created. The technology has been developed and a vacuum distillation apparatus has been created to purify crude selenium, which makes it possible to obtain a metal with a main component content of 99.9-99.99%. Technologies for processing of technogenic wastes and byproducts of the copper industry are developed. Implementation of technologies allow to obtain ammonium perrhenate, perrhenic acid, osmium isotope -187, tribasic lead sulphate, silver-concentrate. The technology of complex processing of black shales of Balasauskandyk deposit with the production of gold, vanadium, rare earth elements, uranium and ferrosilicon has been proposed. The processing was carried out using methods of autoclave leaching, sorption, extraction, precipitation. A highly profitable sorption technology for recovery of rhenium from solutions of underground leaching of uranium ores containing 0.2-0.4 mg/L of Re has been created. The organization of ammonium perrhenate production from solutions of uranium ore will significantly increase the volume of its production in Kazakhstan.

Jan 1, 2018

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By Sumantra Bhattacharya

The per capita energy consumption in India is 510kgoe/year, the global average being nearly 1818kgoe/year. Correspondingly low is the per capita CO2 emission at 1.25t against the world average of 4.39t.65-70%, at times more, of India?s power generation from about 190,000 MW installed capacity, is however coal fired.India therefore has to secure diversified sources of energy and solar power is increasingly being looked as the real alternative to the existing over dependence on coal. To ensure sustainable solar power it is essential to secure its raw material base that is ?silica?, hitherto considered as ?minor minerals?. That calls for immediately addressing the issues of land availability, solar power cost, developing a dynamic inventory of silica containing minerals, appropriate processing technology and strong regulatory framework for sustainable mining and processing of all silica rich minerals. Keywords: silica, silicon, Thar, power generation, India, quartz, solar power

Sep 1, 2012

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By A. V. Bogdanovich

Until recently, in consideration of fundamentals of gravity concentration theory, all computations have been based on determination of particles? fall velocity in an unrestricted medium (hydraulic size). Meanwhile, gravity separation processes are realized under conditions of particles? restricted fall, when important and sometimes decisive role is played by interacting forces of particles, dependent on their varying size, density and shape, i.e., segregation forces. We have developed devices and methods for measuring segregation velocities of fine particles of various size, density and shape during their loosening in air or aqueous medium. Besides, to exclude influence of medium upward flows, loosening was provided by superposition of vertical harmonic oscillations on measuring cell. It was established, that maximum segregation velocities are observed at certain optimal acceleration values and amplitudes of oscillations; excessive loosening leads to mixing and worsening of segregation. Velocity of some particles segregation through others depends on particles? size, density and shape, as well as nature of medium (air, water). Absolute segregation velocities of particles in air medium may reach 1~2 mm/s, in aqueous medium such velocities are by an order smaller. Analysis of rare-metal sands material gravity concentration results showed, that owing to segregation process during gravity separation, fine-size isometric particles of heavy minerals are recovered into gravity concentrates more actively, than larger ones, but more elongated in shape. It is convenient and simple to estimate mineral grains? shape by extent of their oblongness, described as ratio of particle minimal dimension to maximum. Besides, mineral mixtures gravity separation results are directly related to extent of oblongness of heavy particles, recovered in gravity separation process, and also to root-mean-square coefficient of their shape variation. The performed research showed that particles segregation in gravity concentration process plays not a lesser role, than hydrodynamics parameters, and demands further theoretical inquiry and experimental studies.

Jan 1, 2014

By A. K. Mukherjee

In this apparatus closed sized particles are placed in a container and then fluidized by passing water through the load of particles. Water flow is adjusted to deposit particles in one or more layers depending on the specific gravity of each of the particles, after which the deposited particles are separated in portions of different specific gravity. The obtained portions represent different ore content of the closed sized fraction. The process is repeated for all other size fractions to generate washability curve of the feed. Three different types of iron ores and one coal sample are tested in this equipment. The theoretical yield-grade curve generated for iron ore feed is unique in absence of any such practice for ore minerals. Similar curve is generated for coal and it is compared with washability curve, an existing practice followed worldwide. This comparison validates the performance of the process and the equipment.

Sep 1, 2012

By D. Berman, A. Brodt

"Delivery of all volume of mined mass on the terrestrial surface results not only in irrational power expenses on moving of huge volumes of dead rock as a part of initial raw materials (especially vertically) on long distances, but also necessities of storing tailings in open-air. Thus, in bowels of earth, huge volumes of the developed space are formed. However, the nature doesn&apos;t suffer emptiness. As consequence, through the process of underground mining works, in earth bowels starts intensive development of rocks dislocation processes involving subsidence of terrestrial surface, and with it, begins irreparable damage every objects which are on that territory. Highly effective new methods of underground concentration of the various minerals, which deliveries of only target component on terrestrial surface integrally connected with transport process in stream and subsequent deliveries to destination in continuous mode by the long distance hydrotransport, allow not only to eliminate a construction of concentrating factories on the surface, but also storing of tailings of concentration process on open-air preventing dislocation of rocks, thanks to operative placing tails in the underground developed space. Surely, the main problem in the development of such gravity dressing technology is the problem of finding the optimal formula for the heavy liquid that will fill such system in close connection with the procedure of its full regeneration. The requirements for such liquid are being non-toxic and cheap. This question was solved successfully."

Jan 1, 2014

By A. Kogelbauer, A. Stadtschnitzer, A. Boehm, F. Schillab

"The paper covers the design and implementation of an industrial dense medium cyclone plant for carbonaceous iron ore, the proving of efficiency as well as the development of a predictive model for plant control. The VA Erzberg GmbH mines about 12 Mio.t of carbonaceous rock ore at the “Steirische Erzberg”. Due to increased demand of the Austrian steel plants, the production of ore concentrate was raised by 30 % up to 3.0 Mio t/a during the last 5 years. One of the projects to realize the increase in capacity at improved concentrate quality was the implementation of a dense medium cyclone plant for the fine size fraction – 8 +1 mm replacing the former dry permanent magnetic drum separators. By physical separation the siderite variety “spateisenstein” (42% Fe) of a density of 3,8 g/cm³ is separated from ankerite (10 – 17% Fe), the second iron bearing carbonate with a density of 3,2 g/cm³, dolomite, calcite and silicate bearing schists. The feasibility of the process was proven by the test results obtained from a test rig, that was constructed and operated in close cooperation between the Chair of Mineral Processing, Montanuniversitaet Leoben and VA Erzberg GmbH. The density separation surpassed the efficiency of magnetic separation clearly shown by •- values. The plant performance tests (capacity 120 t/h) verify the cut densities defined by Tromp T50 -values and the assigned efficiency found in the pilot tests at varied settings of media density, pressure drop, cone angle and apex diameter. The test rig as well as the final process will be presented. In order to create a tool to predict the performance of the DMS in the centrifugal field at various settings for varying feed composition the experimental results from size and density testing are analyzed in a modified way to obtain physically justified, smooth approximations for the performance curves. Models developed on coal washing plants are checked for their validity at increased densities."

Jan 1, 2018

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and feldspathic sands. These rocks contain other minerals, such as quartz and plagioclase, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse particle size.The feasibility of feldspar-quartz separation using a dynamic dense medium separation system has been investigated as an alternative to flotation techniques. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency.In a full-scale processing plant, a dense medium separation process can be used as a K-feldspar preconcentration step. This reduces the amount of material to be treated in the more expensive processes, such as finer comminution, flotation or magnetic separation.A comparison between commercial raw materials for the ceramic industry and the “rich in feldspar” products of the Tri-Flo process is reported, and the validity of the process is demonstrated."

Jan 1, 2003

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By B. Das

Waste water produced from coal preparation plants posses several problems during dewatering and solid/liquid separation. The natural sedimentation rate of the particles present in colloidal and finely divided suspended form is very slow. Flocculation technology is being applied in most of the coal washeries to recover water which is being accomplished through the use of inorganic salts, polymeric flocculants or both depending on the chemical and physical characteristics of the pollutants present in the waste water. The waste tailing water from Piperware coal preparation plant, Central Coalfield Limited (CCL), India, is highly turbid containing ~ 16000 NTU with negative surface charge in the pH range of 2 to 10. Polymeric flocculants in conjunction with fine magnetite is investigated to achieve faster settling rate with lowest level of water turbidity. The conditions affecting the interaction between the reagents and the turbid particles present in the tailings water are investigated. It is possible to bring down the turbidity of the water to < 90 NTU from very high turbid tailing water by using 2 mg/L of the polymeric flocculent in combination with 0.1 g/L of magnetite at natural pH of the tailing slurry. It has been found that finely divided positively charged magnetite particles in combination with the flocculent selectively coat the negatively charged impurities present in water and thereby increase the settling rate under the influence of a magnetic field.

Jan 1, 2014

By Y. Foucaud, C. Eswaraiah, L. Filippov

Enhanced gravity separators such as Falcon concentrator which uses additional centrifugal force, are the most common gravity concentration techniques used for fine particles processing. Hence, understanding the kinetics and separation mechanisms within these separators is of paramount interest. Recent research yielded a predictive physical model for the Falcon Ultra Fine (UF) which however does not explain some results obtained with industrial ores. This study aims to identify the mechanisms involved in Falcon UF separation with the objective of confirming or rejecting the hypotheses on which the current model is built and suggesting potential points of improvement. The Falcon UF kinetics is investigated through the processing of complex low-grade and fine-grained ores from the Altenberg tin deposit (Germany), the Tabuaço tungsten deposit (Portugal) as well as a synthetic iron ore. Saturation tests are performed on the Falcon UF by controlling the separation efficiency in terms of recovery and enrichment ratio with time or feed mass. Results show an evolution of Falcon UF performance with time in contradiction with the stationary separation hypothesis on which the physical model is based. Observation of the concentrate bed suggests the presence of erosion figures in furrows which may play locally an active role in the separation. In terms of Falcon UF separation timing, three phases can be distinguished. First, upon initial feeding of the bowl, a bed quickly grows unselectively and ultra-fine particles are ejected from the bowl until the bed reaches its final profile. Next, actual separation occurs with selective concentration of dense particles. Finally, capture sites saturate and recovery drops. The evolution of partition curves over time confirms the existence of two separation mechanisms. First, differential particles settling within the flowing film responsible for the ejection of small size particles during the whole separation cycle which is already accounted for in the physical model. The second mechanism involved may be explained by the action of lift force, neglected in the physical model, which acts preferentially on coarse particles deposited at the surface of the bed resulting in coarser particles being rejected in the tailings. Hence, the addition of a lift force component to the existing model is suggested to account for this second separation mechanism.

Jan 1, 2018

By R. Shiva Kumar, G. E. Sreedhar, Rajan Kumar, K. Suresh, A. K. Aketi Veera, M. Narasimha, P. S. Jodan

"In most of the coal washeries, Dense Medium Cyclone’s (DMC) are deployed to treat coarse coal fraction in the range of 50-0.5 mm. DMC’s are very popular due to its ability of high tonnage, ease of operation and effective separation at high near-gravity material (NGM) in feed coal. The ease or difficulty of washing is merely depending on the NGM fraction present in run of mine coal. However, the quantitative effect of NGM on DMC performance was not explored in the literature. Hence, in this investigation, the influence of NGM on DMC performance is focused. With the help of synthetically prepared coal mixture, the effect of NGM mass fraction on separation efficiency is studied in three different approaches. Firstly, by increasing the NGM coal fraction systematically from low to as high as possible; second by varying the distribution of NGM coal; and third by varying distribution of particles lying just above and below the near-gravity zone. Washability studies are also carried out to establish the theoretical yield for the prepared synthetic mixtures. Pilot-plant experiments are carried out in a 4-inch DMC with 1.4 operating separation density treating coal in the size range of 4 - 0.5 mm. From results, the partition curves are constructed by both density and size wise distributions. It is observed that at higher NGM coal fraction i.e above 60%, the performance of DMC is very poor with significant coal particles misplacement. In second approach with increased distribution at higher density fractions, the separation efficiency reduces. In third series the distribution of fraction in near-gravity zone doesn’t much effect the separation except the shift in separation density. It is observed that smaller size (-0.5 mm) coal particle having high NGM content seems have a profound effect on DMC performance leading to significant fines misplacement to wrong products."

Jan 1, 2018

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003