Search Documents

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By A. Wilkinson

An investigation into the performance of support systems that are currently used in South African coal mines was conducted. Five most critical components of a support system have been identified. These components are resin, bolt, hole, machinery/equipment and the rock type. All five of these components are equally important as failure in any of these components will result in an inadequate support system. The performance of resin used in South Africa was investigated through in situ short encapsulated pull tests. The results indicated that in the majority of pull tests, failure took place at the rock-resin interface, indicating that the rock failed before the resin shear strength had been reached. It is therefore concluded that the strength of resin currently used in South Africa is adequate. It is found that although the maximum bond strengths achieved form both resin suppliers were similar, there was a considerable difference in the stiffhess of the resins. Roof bolt diameters and rib heights of bolts from three major manufacturers were evaluated (approximately 80 roof bolts from each manufacturer). The results showed there is a significant variation in bolt diameters and rib heights in the same batch in roof bolts supplied by certain manufacturers. The results also showed that on average there are insignificant differences between the parameters that determine the bolt profile (rib angle, spacing between the ribs and rib thickness). The influence of these parameters on bolt performance was very small and could not be established in situ. Roof bolts from four major suppliers were also evaluated through in situ short encapsulated pull tests. The results showed that the reinforcing system using roof bolts from all four manufacturers performed almost identically in sandstone, but somewhat differently in other rock types. The effect of bit types was evaluated. Both the stresses and the maximum loads obtained from the two-prong bits were greater than those obtained from a spade bit. Borehole annulus was found to be another important parameter that determined the support performance, and was investigated. The results from these tests showed that an annulus between 2.8 mm 4.5 mm resulted in the highest bond strengths. The results also showed that as the annulus drops below 2 mm, it appears to have a negative effect on the bond strength. The effect of wet and dry drilling on support performance was investigated. The results showed that wet drilling can-provide relatively greater system stiffnesses and slightly greater bond strengths. Short encapsulated pull test results showed very distinct differences between bolt system performance in different rock types and that sandstone produces significantly better results than shale and coal. From the results it is concluded that rock type is probably the primary factor influencing support system performance. A detailed investigation into the specifications of roofbolters that are currently being used indicated that the quality of installation of a support system is directly related to the performance of the equipment that is used to install the bolts. The important parameters, torque, thrust and speed of bolting equipment were investigated. The results showed that there are significant variations in these parameters in South African roofbolters.

Jan 1, 2005

By Vince Caggiano

The newly developed Hilti OneStep roof bolt combines the standard 5-step anchoring process (i.e. drilling, transfer of drill steel, insertion of resin, insertion of rod and tightening) into one easy operation. It also replaces 4 items (drill head and steel, adhesive cartridge and anchor) for simplified material management. This paper describes its history of development, and bolt, bolt drilling and bolt resin specifications, experimental test results in Germany where it achieved a reduction of 36-42% in roof bolt cycle time and 25-30% improvement in gateroad development rate. In the U.S. coal mines, a time study showed that OneStep can save approximately 50 seconds in installation time per bolt.

Jan 1, 2005

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By Jingyi Cheng

Many longwall panels in China are laid out along the dip direction such that the direction of longwall retreat mining is along the strike direction of coal seams. Downward mining longwall panels in steeply inclined seams refers to those that are laid out in a non-uniformly developed fold structure where the seam is not only steeply dipping, but also highly undulated along the strike direction, causing longwall mining extremely difficult because it has to deal with large dip angles that vary both in the mining and faceline directions. Obviously, the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply dipping seams have unique patterns that are very much different from those cases of mining the flat or gently inclined coal seams. The effects of those unique patterns presented a big challenge to production and safety. Almost all previous and current researches on ground control have been concentrated on issues related to the flat and gently inclined coal seams. Conversely, research on steeply inclined coal seams, especially those with large angle variation both along the seam dip and strike directions is almost none. Therefore, it is very important to initiate a study to better understand the characteristics of mine pressure and overburden strata movement for this special type of geological condition. The objective of this paper is to monitor and analyze the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams, the angle of which varies greatly along both the seam dip and strike directions. The measured data has conclusively demonstrated that the characteristics of mine pressure and overlying strata movement in downward mining longwall panels in steeply inclined seams are different from those for the flat and gently inclined coal seams. The large downward angles of coal seam undulation along the strike (mining) direction can obviously affect the roof movement and reduce strata pressure. Study in this research showed that appropriately increasing the rate of mining (or face advance) is positive to roof control.

Jan 1, 2013

By Bruce W. King, David A. Newman

"Underground mines have always been an integral part of the limestone industry. However, beginning in the 1990s, the number of underground limestone mines has increased for many reasons including• Stripping ratios at surface quarries have become uneconomic.• Existing surface quarries have reached the mineral boundaries, and the remaining stone reserves are underground.• Surface access to the entirety of the limestone reserve is limited by development or infrastructure.• The once-rural setting of the surface quarry is now surrounded by subdivisions and development. An underground mine is less intrusive and takes the mining operation out of the public eye.• For larger markets, an underground mine enables year-round production without the sequence of overburden stripping in the winter to expose mineable stone for summer production. This is common at many surface quarries.Multiple-level operations are a natural extension of the decision to mine underground. Most limestone reserves, for example, the Tyrone-Oregon-Camp Nelson, Hermitage-CartersLebanon- Ridley, and Salem Limestones, are sufficiently thick to accommodate multiple levels. Multiple-level mines should be planned by considering each level separately and then integrating the individual levels into a larger mine plan. Failure to plan all the levels of a multiple-level mine in concert can result in ground control (back, pillar, floor, and inter-level sill pillar) problems attributable to stress transfer and interaction between the levels or the necessity to leave a thicker sill pillar between adjacent levels.Multiple-level mine planning begins with geology. Once the upper level back horizon is identified, the geology, rock strength, and physical properties in each level are used to• identify the optimal back horizon• quantify whether back support is required and, if so, the type, spacing, and length of the back support• determine the pillar centers• determine the total mining height, including floor shots"

Jan 1, 2016

By Y. P. Chugh

The use of wooden supports, supplementary to the primary method of roof control using roof bolts in mines, consumes over 3 million cubic meters of hardwood in the U.S. annually. These supports arc primarily used in the form of cribs and posts. Along with a rapid depletion of high quality timber resources, supplies fluctuate seasonally, costs are escalating rapidly, and product quality is highly variable. Environmental considerations of global climate change put additional pressure on deforestation for utilization of timber for artificial supports. On the other hand, management of coal combustion byproducts (GCBs) from power plants has become a major issue to maintaining a healthy coal industry. The USA currently produces over 100 million tons of CCBs annually and the average cost for their management in the US is about $20/ton. This cost is expected to escalate rapidly with tougher environmental regulations. The principal author has been directing research, development, and demonstration studies for CCBs-based artificial supports and lightweight structural materials in mines for the past seven years and has made significant progress toward commercially viable products. More specifically, first and second generation crib elements and post elements have been developed, characterized analytically, and demonstrated in the field. It is estimated that about 2.5 x 10" tons of fly ash could be utilized for artificial supports in U.S coal mines and this would double if these materials were utilized in non-coal mines as well. The author believes that CCBs-based artificial supports have the potential to replace wooden supports and blocks with better performance and cost competitiveness while managing CCBs in an environmentally sound manner. This paper focuses on the development and field demonstration of CCBs-based artificial supports for use in underground mines, and its pilot scale fabrication facility. Recent analysis results on engineering performance evaluation of the developed crib under various loading conditions using finite element method are presented. The following comments highlight the developments: I ). Engineered artificial supports, crib and post elements, using CCBs as a major constituent, have significant potential for application in mines because their structural performance is significantly better than wooden cribs counterparts. 21. Engineered crib elements provide about 50% larger area for air-flow than a conventional wooden crib. 3). Engineered crib elements are not flammable. 4). Each engineered crib element utilizes about 10 kg of fly ash, about 40 % of the weight of crib element- Therefore, a typical crib 2.0 m high utilizes about 200 kg of fly ash. 5). Each 16.5 cm diameter engineered post utilizes 50 kg of fly ash. 6). Assuming 3.0 million cu. meter of wood consumed for post and crib support systems, it is estimated that about 4 - 5 million tons of fly ash may be utilized for supports fabrication in the USA. 7). An engineered post has excellent post-failure characteristics similar to wood. In addition, the engineered post also has excellent loading and unloading characteristics close to the yield point of about 75% of the ultimate load carrying capacity.

Jan 1, 2004

By David A. Newman

In the 1950s, an underground limestone mine in the Camp Nelson Formation was developed from an outcrop exposure. The Camp Nelson Limestone met the requirements for DOT stone and aggregate. The mine ownership changed several times, which resulted in distinct mine designs in Level 1. Based upon the production requirements and an attempt to maximize limestone recovery from a single level, a variety of pillar dimensions and three mining heights (28 feet, 68 feet and 83 feet) were developed. This was sufficient prior to reaching the mineable extent of Level 1. Level 2 introduced previously unknown ground control challenges. These included: ??Pillar spalling and a significant back fall on the Level 1 - Level 2 decline; ??Laminated immediate back and the need to bolt the back on Level 2; ??Delamination of the back adjacent to the Level 1 - Level 2 decline resulting in bolt shearing, and floor heave in isolated areas of Level 2; ??Multiple level interaction, the need to design pillars based upon numerical modeling as columnization between Levels is infeasible: and ??Water inflow as the mine approached river. To meet the challenges, a testing program to determine rock strength and physical properties was implemented along with numerical (LAMODEL and FEM) modeling, and borescope inspections of the immediate back. The efforts to implement rock mechanics were re-focused as Level 2 approached its mineable limit and the initial attempt to drive a decline to Level 3 was unsuccessful. A second decline site was selected based on inter burden stability, a consistent shale parting for the Level 3 back horizon, results from numerical models of the immediate back and multiple level interactions, and the projected low water inflow. The mine is operating on Levels 2 and 3 with long-term planning and ground monitoring for Level 3.

Jan 1, 2014

By J. Nielen van der Merwe

The main objective of the research described in the paper was to determine the causes of falls of roof in South African coal mines. The south African Colliery Manager's Association and the members of the South African National Institute of Rock Engineering (SANIRE) who are employed by coal mines lent full support to the work. Fifteen major roof falls were investigated in detail and their causes established. This data was supplemented by mapping a large number of roof falls on four coal mines in less detail. The total number of recorded roof falls was 182. The data bank simulated the data bank of roof falls that resulted in fatalities in terms of the total number of falls recorded and the thickness distribution of the collapses. It was found that the causes of the falls differed for different thickness ranges of roof falls, The thin falls, classified as "Skin falls", which accounted for approximately 70% of all fatalities, were predominantly caused by ineffective joint support and excessive bolt spacing. Ineffective joint support was found to be a dominant cause of roof falls for all thickness ranges, while the influence of excessive bolt spacing diminished with increasing fall thickness. However, it remained a significant cause of roof falls even for the major falls. Burnt coal, dykes, bad mining practice, weathering and inferior materials were found to be minor causes, but nonetheless contributed to the falls. Horizontal stress was a minor cause, with increasing contribution for thicker falls. It was also found that the indicators of horizontal stress coincided with areas of reduced roof rock strength. In general, roof falls occurred in areas where the roof rock was found to be less competent in terms of rock mass rating systems. It was concluded that the Coal Mine Roof Rating (CMRR) system developed by NIOSH in the USA held promise for application in South Africa and should be investigated further.

Jan 1, 2001

By Dennis Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson's effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

Jan 1, 2003

By Vladimir I. Klishin

Complex method of ruling of rock pressure is considered in conditions of rapid roof subsidence. The purpose of this method is elaboration of emergency devices into hydraulic props. Also method of unloading of solid roofs is worked out. An analysis of means of protecting hydraulic props of powered supports 6om dynamic loads made it possible to divide them into four classes according to principle of operation: emergency, operating hm an increase of pressure; emergency damping; emergency, operating according to the "plastic element" principle; inertial emergency, operating hm dynarmc loads. It was established that the overwhelming 'majority of designs of the first three classes of emergency devices (EDs) are based on !mditional approaches, which exhausted their possibiiities of high-speed response. Delay on their opening is caused mainly by inertia of the moving locking parts. In our opinion, the most prospective are EDs using the inertia of the moving locking parts for depressurizing the piston cavity of the hydraulic prop with a minimum delay (inertial EDs). The essence of the designs of EDs having an inertial principle of action is that into the hydraulic prop containing movable and immovable elements is additionally introduced a spring-operated contracting support, which is installed on the movable element. Under dynamic loading of such a hydraulic prop hm the roof, the support moves relative to the movable element, performing the role of an inertial mass, which leads to instantaneous depresswization of the piston cavity of the hydraulic prop. Technological measures for unloading of solid roofs consists in creating of long oriented cracks in rock massif. Description of method for creating cracks, demanding equipment and means for cone01 the progress of splits are included. Also technological schemes for realization of the method of saving underground mines and rock mass are included. The results of experimental realization of this method on the Kuzbass and Poland coal mines are also included.

Jan 1, 1997

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By Craig Collins

The objective was to develop a Real Time Drilling Display System for Rotary Roof Bolting using Analyzing Software to display mapped holes as they are being drilled in real time. The Analyzing Software was developed to analyze and interpret drill sensor data produced during a rotary drilled roof bolt hole by using algorithms and drill sensor data trends to find and locate roof separations or voids. After this software was validated through lab and field testing, its application needed to be tested in a production environment. However, the current method used to record the drill sensor data proved to be cumbersome for the mine to use on a continuous production basis. With different more practical mediums being explored and considered, a Drilling Display System was developed that will both map holes in real time and record the data for later review. With the Analyzing Software's current level of accuracy and with the convenience offered by the real time Drilling Display, the Drill Display System was implemented along with a test mine's current roof control plan and tested as a roof separation "Early Warning System". After installing the Drilling Display System onto a machine, input and suggestions from the mine environment were considered and design changes were made. The real world application provided a design direction that made the information produced by the Analyzing Software both convenient and significant for the test mine. Also, using the Drilling Display System increased the number of drilled holes that were both mapped and recorded. The results from studying these recorded data files lead to refinements in the current algorithms used by the Analyzing Software which increased the overall accuracy and capability of the system A fairly accurate representation of void or separation locations in the mine roof can be determined fromsensor data recorded during production bolting cycle. The immediate feedback on the local roof condition that the Drilling Display System provides, amounts to a quicker and safer alternative to the scratch hole and the video bore-scope examinations that arc performed after the bolting is completed. This project has shown that making the alternative method of examining the roof condition practical for the mine to use is just as important as the accuracy of its results. Based on the results of this field test, this or other methods of reviewing the analyzed drill hole data will be explored.

Jan 1, 2004

By Klaus Opolony

The German coal industry operates a multi-seam extraction system, with average working depths currently around 1,000 meters. The gate roads serving the longwalls are often used for a second time - a practice which has the advantage of allowing several panels to be extracted with a minimum of roadway drivage work. This preference for re-using gate roads is based on a number of factors: such an arrangement a) prevents the strata pressures in the subsequent panels from being adversely affected by the presence of support pillars, b) helps achieve the target of full mineral extraction and c) allows the roadways to be used for air conditioning and ventilation purposes as part of an advancing longwall system. This paper explains the planning procedure required for a rectangular rockbolted roadway, using as an example a gate road in the 3 meter-thick D2/C seam at Lippe colliery, and describes the subsequent operating experience. Here special attention is focused on modem procedures and techniques for mine roadway planning. The investigation also examines the part played by the mine ventilation system and the available machine technology, which are particularly important parameters for the design of the T-junction areas and support system. Keywords: multiple seam extraction, longwall mining, roadway drivage, roof bolting, roadside pack system, hydraulic frame type support.

Jan 1, 2002

By H. Maleki

Gob pressure measurements were made in a Western U. S. coal mine as part of a long-term program to evaluate cave progress and to determine the influence of geological discontinuities on caving conditions, load transfer, and resulting instabilities. Gloetzl cells were selected for the measurements due to their simple, robust construction and a history of being able to monitor pressures in a broken medium. A methodology was developed for the successful installation and protection of the cells and hydraulic lines in the gob as the face retreated. The measurement indicated a cave progress controlled by the frequency of, major faults. The pressure-mining progress profile was compared to those observed in other parts of the world. It was concluded that the significant differences in profiles was caused by the thick-bedded strata, the existence of high lateral stresses and the spacing between faults. Recommendations are given for future applications of Gloetzl cells for gob pressure measurements.

Jan 1, 1984

By Noor Mohammad

Comprehensive numerical modelling of the subsidence associated with longwall mining in UK Coal Measures strata has been conducted and validated against UK data. The Rock Mass Classification System (RMR) was used as the main basis to derive representative in-situ rock mass properties for stiffness and strength parameters for the numerical modelling input. A Finite Difference Method, Fast Lagrangian Analysis of Continua (FLAC) has been used to design a suitable non¬linear model and simulate the behaviour of the caved zone with a unique modification of the post failure properties within the zone of influence. The established model was validated for different configurations, varying depth, panel width and extraction thickness, in a sensible and realistic range. The Subsidence Engineers Handbook (SEH) and a stress abutment model were used as a validation tool in this respect. The approach developed will be modified for application to a number of different International Coalfields with different geological environments.

Jan 1, 1997

By Duk-Won Park

The excavation of a longwall panel causes a continuous stress redistribution in the surrounding strata for every face advancement. The understanding of the behavior of rock to high level of stresses is instrumental to the structural design of underground mines. In order to achieve a realistic analysis of the behavior of strata, the three-dimensional finite element method is frequently used. Also the model developed for the analysis has to be designed large enough to represent the influenced strata in the study area and a sufficient number of elements has to be used to provide detailed information on the stresses and displacements. Due to the size of the model and its numerical solution the CRAY X-MP/24 supercomputer has been used for this study. The mine site selected for the analysis is a coal mine located in the Black Warrior Basin in Alabama. The mine has two longwall sections at a depth of 2,000 feet with various dimensions of chain pillars, including yield pillars. Various research programs at this mine have been carried out by Park et. al. ( 1984 ). Therefore data were already available on the geology, and physical properties of rock and coal. In addition a rock testing program has been carried out to obtain rock mass classification parameters. The progressive failure technique has been utilized to simulate stress redistributions. The failure criterion after Hoek and Brown ( 1980 ) which is based on rock mass behavior was used for the iterative technique. Simulated stress redistributions are therefore very realistic. In order to automate the process involved in the application of progressive failure technique, a computer program has been developed. The combination of a large scale three-dimensional finite element model and the automation of progressive failure simulation provided a tool that can generate a large amount of information related to the behavior of rock and coal as a response to a longwall mining operation.

Jan 1, 1989

By W. Mark Hart

The current Automatic Data Acquisition system developed by some support manufacturers make it possible to monitor and record changes in leg pressure, DA RAM stroke in every shield and shearer position at any moment during mining operation. But how can these massive data (more than 1 MB for every 3 hrs for the current scanning option) be effectively used for improving production and maintenance management as well as providing better roof control at a longwall face? The research currently conducted jointly by WWU and Cyprus Amax Minerals at Emerald Mine and Twentymile Mine attempts to answer this question and make the data, especially leg pressure, more meaningful. A computer software package has been being developed to (1) determine mining cycles, cycle time, face advance rate, production rates, machinery delays, and production delays for each shift; (2) identify defective sensors, check valves, yield valves, by-passing leg and DA RAM cylinders, and other hydraulic and electrical abnormalities; (3) determine the roof weighting period; (4) evaluate the performance of the current shield support design - demand relationships; and (5) predict and overcome ensuing encroaching problems and roof conditions ahead of the face.

Jan 1, 1994

By Kot F. v. Unrug

The depletion of thicker coal reserves has resulted in the thinner seams being economically attractive. Surface protection against subsidence limits the extraction ratio to 50% for the room and pillar method as a "no subsidence condition". That rule was developed for pillars with smaller width/height ratio because seams mined at the time were commonly 6 feet thick. Over time pillar ribs deteriorate around the pillar perimeter and thus decrease the area of the pillar. Using 50% extraction as the no subsidence condition in the squat pillar category (below 42 in with w/h > 7) causes unnecessary losses of reserves because squat pillars are stronger. In this paper a method is presented for design of long-term pillars. Based on the analysis of pillar deterioration and field observations, an increase of the "no subsidence" extraction rate to 60% for squat pillars is proposed.

Jan 1, 2001

By Hamid Maleki

A novel ground control program has been developed at Plateau Mining Company through five years of geotechnical investigations. The study was initiated to determine the causes for roof stability problems and to develop alternative support and monitoring systems for increased safety and productivity. From systematic roof fall observations, extensive geologic mapping, roof drilling and monitoring ground movements along gate entries of four longwall panels, a sand- stone channel system was detected and shown to impact roof stability. In particular, underlying mudstones up to seven feet thick experienced instability due to differential compaction and load transfer from the gob. Roof bolter operators were trained to report roof lithology for mapping channel positions into the roof and for selective use of longer bolts. This boosted operator morale, and improved ground conditions. Monitoring rates of roof movement is used in these areas for detection of instability and for application of secondary support: This has significantly increased safety and productivity.

Jan 1, 1987