Search Documents

By S. L. Windes

"INTRODUCTION For a number of years the bureau of Mines has been engaged in the detection, recording and interpretation of earth- and air-transmitted disturbances, man-made and natural, related to mining operations. For the measure¬ment of such disturbances, special equipment was developed (1, 2, 3, 4, 8) 3/ and results of the measurements have been reported (5, 6; 7,9).In general, the ranges of amplitude end frequency of vibration encountered and recorded in the earth-transmitted disturbances were 0.00005 to 0.1 inch and 5 to 5,000 cycles per second; in the air-transmitted disturbances, pressures ranging from 0.001 to 100 pounds per square inch and 0 to 20,000 cycles per second were recorded.One characteristic of the earlier tests was that either the arrival time of the disturbance to be recorded was predictable or the recording speed was slow enough so that the record covered extended periods of time (for example, 4 hours). As the investigations continued, it became apparent that a recording device was required that would respond to transient vibrations arriving at indeterminate times and at the same time provide a permanent record of displacement or acceleration versus time on a scale that would permit the analysis of waves having frequency components up to 10,000 cycles per second. A film or paper speed of 720 inches per second was found to be adequate, as this provides approximately 3/4 inch of record for each 0.001 second."

Dec 1, 1947

By W. C. Smith

This Bureau of Mines report discusses how pull-test data can help establish polyester resin column length criteria for roof bolts in evaporite minerals. The study evaluates the effectiveness of partial to full columns of resin in anchoring 4-ft, No.6, grade 40 rebar roof bolts in potash, salt, trona, gypsum, and borate mine roofs. Pull tests were performed on over 600 roof bolts in 11 evaporite mines. Column lengths ranging from 6 to 48 in (fully grouted) were evaluated for each test site. In general, comparative results among all test sites indicate that pull-out loads in excess of 10 tons (force) were attained with resin-grouted bolts having 13 to 75 pet less than a full column of polyester resin. Ten tons (force) of load-carrying capability compared favorably, in terms of strength, with the calculated yield strength of the rebar used in the tests, which was 8.8 tons (force). The site-specific nature of each test site, due to the unique combinations of geology, mine-induced stresses, and other unknown parameters, prevented the establishment of valid generic column-length criteria. For these reasons, data to evaluate resin-column-length effectiveness are best obtained on a mine-specific basis.

Jan 1, 1987

By J. E. Tiffany

A stick of explosive is a package of stored energy that can be released when needed to blast rocks, coal, and other materials; but, unlike fuels such as coal and gasoline, its potential energy is self-contained, there being enough oxygen within the package to complete the almost instantaneous reaction. When an explosive is ignited or detonated, the solid or liquid materials of which it is composed are converted rapidly into highly heated gases, which, if free to expand, would have a volume many times larger than that of the original explosive. At the instant of explosion these gases occupy only the volume of the shot hole and are therefore produced at a very high pressure, which causes the material that is being blasted to be broken or disrupted. In blasting coal efficiently the proper placement of the shot hole and the confinement of the explosive therein are both of prime importance. When these are not adjusted properly, only a small amount of the energy is expended in bringing down coal, consequently the balance of the energy tends to be expended by the emission of a flame into the working place that may lead to a gas or dust explosion. Permissible Explosives Defined The term "permissible explosive", as applied by the Bureau of Mines to explosives it has approved for use in blasting in coal mines, embraces not only the requirement that the explosive, when used, shall be similar in all respects to the basic sample that passed all the tests necessary for its admission to the published permissible list, but also that the explosive shall be used under certain prescribed requirements.

Jan 1, 1938

By Deno M. Pappas

The objective of this Bureau of Mines investigation was to identlfy and evaluate alternative binder materials for use in stabilizing and consolidating highly fractured roof along longwall faces and gate roads. The desirable characteristics of a stabilization material were defined, and an extensive search was conducted to find materials satisfying these characteristics. Of 20 materials originally scrutinized, 9 were chosen for laboratory analyses. The laboratory tests evaluated bond strength and tensile strength under both dry and wet conditions. An optimum material was not found. The laboratory analyses indicated two possible candidate materials for longwall stabilization: high-aluminous cement and two-component epoxy; however, the tensile strength of the high-aluminous cement was mediocre, and the epoxy cement is toxic, flammable, and fairly expensive. The potential market demand for an effective and economical stabilization macerial is discussed in the appendix.

Jan 1, 1988

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By G. L. Oldright

[Processes by which silver alone is extracted from ores that also cant contain base metals are usually associated in the mind of the period when mines were changing from the production of noble metals to the production of base metals containing noble metals as a by-product. In this transition period the mixed arcs of the partly oxidized ore zone had to be treated instead of the free-milling ore that had been treated in the past or the deeper-lying sulphide ores that were to be smelted subsequently under improved economic and technical conditions.]

Jan 1, 1929

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By David K. Denton

There are no active mines in the Mt. Eddy RARE II area. Chromite, gold, and stone prospects were examined. The RARE II area contains no identified mineral resources; however, a sample of a 260 ton occurrence contained 38.1 percent chromium oxide (Cr203) at the Ratero Prospect (fig. 1, no. 3), which has low potential for chromium resources. The Johnson Mine (fig. 1, no. 6) produced a small unrecorded amount of chromite during World War IT, but only a low potential exists for chromium resources. A low potential exists for gold resources at the Half Century Prospect (fig. 1, no. 2). At a borrow pit northwest of the study area (fig. 1, no. 1), sheared serpentinite is quarried for road metal; similar rock occurs in the RARE II area, but better material is more readily available elsewhere. Sand and gravel occurrences are too inaccessible and distant from markets to be considered resources. Mineral fuels and geothermal resources were not evaluated during this Bureau of Mines study. There currently are three unpatented lode mining claims in the study area. INTRODUCTION The Mt. Eddy RARE II area is 7 air-mi west of Mt. Shasta City, California, and straddles the Siskiyou-Trinity county line. The roadless area includes 7,200 acres of rugged, glacially carved, ridges and drainages which comprise Mt. Eddy. Elevations vary from 6,000 ft along the North Fork Sacramento River to 9,025 ft at the summit of Mt. Eddy. The area is covered with conifer forest below 8,000 ft elevation.

Jan 1, 1983

By E. B. Swanson

Atlantic seaboard refining and marketing companies , dependent largely upon other producing and refining areas for the crude and refined petroleum needed to meet the demand for petroleum products within the Atlantic Coast States , reported an increase in 1929 receipts of 2,542,000 barrels of crude petroleum and 13,479,000 barrels of gasoline over the quantities received during the preceding year . The relatively large expansion in gasoline receipts undoubtedly resulted from the unexpected increase in gasoline consumption which characterized the petroleum industry during 1929. Gasoline receipts from California increased 6,354,000 barrels and shipments from foreign countries were 5,381,000 barrels in excess of the 1928 figures , while receipts from Gulf Coast ports , the major source of outside supply, declined 811,000 barrels . Shipments of domestic crude oil by tanker from Gulf Coast ports during 1929 continued the average annual increase of approximately 7,000,000 barrels which has been recorded during the five years of this annual survey . These shipments have increased from 72,556,000 barrels during 1925 to 99,828,000 barrels during 1929. Shioments of Mid- Continent crude by pipe- line to Atlantic Coast refineries have , on the other hand , dropped from 11,903,000 barrels in 1925 to 1,409,000 barrels during 1929. Receipts of foreign crude oil declined 1,461,000 barrels from the preceding year . : Gasoline demand within the Atlantic Coast area reached a total of 123,345,000 barrels , an increase of 15.7 per cent over 1928. Gasoline production increased 4,157,000 barrels , while tanker receipts were nearly 11,000,000 barrels larger than in 1928. Indicated shioments from Appalachian refineries were somewhat larger than in the preceding year . Gasoline production showed an average of 33.5 per cent of the crude throughout , as compared with 31.5 per cent in 1928 and 32.7 per cent in 1927. Cracking operations accounted for 44.6 per cent of the gasoline produced , as compared with 40.6 per cent in 1928 and 35.3 per cent in 1927. Gas oil and fuel oil production averaged 52.8 per cent of the crude throughput , as compared with 55.1 per cent in 1928 and 49.5 per cent in 1927 , the decline reflecting the smaller quantities of foreign crude refined during the year .

Nov 1, 1930

By R. T. Stull, G. A. Bole

Previous Work . The Bureau of Mines reported a survey of bond clays for graphite crucibles at the American Mining Congress which met at St. Louis in November , 1919 *** . The report contained information in regard to : (a) tests carried on to determine the effect of substituting Canadian and Alabama graphites for Ceylon graphite in varying proportions . The data indicated that Alabama graphite is superior to Canadian graphite and further , that Alabama can be substituted for Ceylon graphite to a large measure without lowering the quality of the ware . These tests were made on No. 70 size brass melting crucibles and were carried out under foundry practice . (b ) Tests were reported in which an attempt was made to modify the nature of Alabama graphite by heat treatment so as to resemble Ceylon graphite . Little advantage from the treatment was reported . With this general information as a basis , the experimental work proceeded along two lines : A study of bond clays for steel -melting crucibles and for brass -melting crucibles . Twenty- one sets of standard-size crucibles were made up of a body containing Ceylon graphite as standard , bonded with 21 bond clays . These tests were carried out under foundry practice as were the former tests . Three domestic clays proved to be superior to the standard Klingenberg clay formerly used in brass -melting practice while in the steel - melting industry , 13 domestic clays gave service superior to Klingenberg clay .

Aug 1, 1923

By Robin B. McCulloch

No producing mines are in the study area. Sample results indicate the only resources in the study area are low grade phosphate deposits associated with Cuyama Phosphate Mine (fig. 1). Within the study area, are more than 21.4 million tons of inferred subeconomic phosphate rock resources which would be reserves at an 80 percent higher phosphoric acid price; weighted average grade is 4.84 percent phosphorous pentoxide (P205). About 17.6 million tons of similar grade are outside the area to the northwest. The South Cuyama Oil Field, adjacent to the study area (fig. 1), produces petroleum from the Vaqueros Formation which underlies parts of the study area. Oil and gas potential was evaluated by U.S. Geological Survey. INTRODUCTION Location, Size, and Geographic Setting The U.S. Bureau of Mines conducted a mineral survey of the Fox Mountain RARE II area (No. 5120) during the summer of 1981. The area was examined to determine the presence or absence of mineral resources and reserves, and to estimate tonnage and grade where possible.

Jan 1, 1982

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By X. Shi, N. S. Dala, V. Vallaythan

"Cellular damage induced by silica dust is known to be associated with increased fragility and destabilization or destruction of the cell membranes. The mechanism by which silica dust effects biological membranes is still unknown. Using the ESR spin-trap methodology, we find that hydroxyl radicals are generated in aqueous suspensions of freshly ground silica. The amount of the radicals generated depends on the extent of grinding and ""freshness"" of the dust. Using linoleic acid as a model lipid, we show that the silica dust causes lipid peroxidation via ·OH, 02-, or linoleic acid related radicals as intermediates. Catalase and superoxide dismutase inhibit the formation of these radicals. The results suggest that free radicals associated with freshly ground silica and the related lipid peroxidation of the memberanes may be the starting point of the silicotic processes.INTRODUCTIONDespite considerable-effort over the years, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrosis are still not fully understood (1,2). It is generally thought, nevertheless, that the interaction of the quartz particles with the cell membranes is the starting point of the silicotic process (3). We felt that the mechanism of the membrane damage by quartz might involve oxygenated free radicals because (a) a suspension of quartz particles in contact with alveolar macrophages has been reported.(4,5) to initiate an enhancement of lipid peroxidation, defined broadly as the ;oxidative deterioration of polyunsaturated components of lipids, and (b) hydroxyl (·OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (6) and initiating lipid peroxidation in lysosomal membranes (7). Moreover it is known that exposure of cell membranes, fatty acids and unsaturated food oils to ionizing radiation, which generates ·OH. radicals, causes rapid peroxidation (6). Earlier studies o~ the aqueous chemistry of quartz suspensions have reported detection of HzOz (8), implicating the formation of ·OH radicals as transient species, but, we are not aware of any report of the detection of ·OH radicals in quartz suspensions and this provided the motivation for the present undertaking. Since it is known that, because of their high reactivity (hence short life time) in aqueous media, the ·OH radicals cannot be detected via electron spin resonance (ESR) directly (9,10), we have used ESR combined with the spin-trap methodology (9) for studying the •OH formation."

Jan 1, 1988

By R. D. Ladoo

"At the beginning of 1920 a general feeling of optimism was noted in many talc-producing districts. The industry seems to have recovered from the temporary depression of the first half of 1919 and many mills are running at capacity production with their entire output for 1920 contracted for. The imports of talc for 1919 were only slightly larger than in 1918 by weight and probably no more by value. Thus foreign competition has not begun to be seriously felt. Several new companies in this country have been organized, some to operate new deposits and others to continue the work done by others.An interesting phase of the present situation is the possibility of increased use of talc in paint. There is a shortage of barium sulfate used as,paint filler. Since, for some uses, talc is considered second only to BaSo4 as a filler for paint, it is possible that part of the shortage could be relieved by an increased use of talc.A series of physical tests upon all pigment materials used in the manufacture of paints is being conducted for the Paint Manufacturers Association of the United States. It is important that all types of talc be represented in these tests. Producers of finely ground talc, 200 mesh and finer, are urged to submit samples of at least two pounds each of these grades that are available to paint makers with trade name and quality data, to the Institute of Industrial Research, 19th & B Streets, Washington, D. C., where the tests are being conducted.The Talc Products Company, Inc., Washington Building, Los Angeles, California, has recently been organized to develop a large body of talc one mile north of Riggs, San Bernardino County, California, This deposit contains a compact, white talc which can be sawed into crayons. The company's mill, at Los Angeles) is equipped with a unit of the Raymond system of grinding and air separation, and pencil sawing machines. It is reported that the pencils are being successfully used in Pacific Coast ship yards.The mining of talc where no mill is owned by the operator and the consequent sale of talc in its crude massive state has not proved profitable in a number of cases recently noted. Under exceptional circumstances, where mining costs are low and the product can be sold to a mill near the mine, the operation maybe profitable, but this condition is not common. One mine of this type has recently closed down, at least temporarily; but a second, more fortunately situated, in another district, is continuing operations, although plans are being made to erect a mill in the early spring. Most satisfactory results are ordi¬narily obtained where the mine and mill are owned by the same company.The sale of the Balmat mine of the International Pulp Company, near Gouverneur, N. Y., to J. H. McLear, Gouverneur, and H. G. McLear of New York, has been reported. It is stated that a large part of the property has been already leased to the Sylvia Lake Company, who will operate it. ""Cement, Hill, and Quarry""* states that ""the first mining done on this property was for silver and lead, but it developed into a good zinc producing property and later it was worked for its talc deposits. It has passed through several hands, the American Pulp Co., the Union Talc Co., and the International Pulp Co., all having had it in successive periods since 1891."""

Jan 1, 1920

By G. W. Jones

[A survey of the Ii terature reJ.l....ting to iE;li tion temperatures of acet-ylene-air and acetylene-oxygen mixtures reveals rather '.'fide disagreement in the reported results. In SO!':1e instances the i ition temperatures of acet?-ylene-air mixtures were reported to be lower than those of acetylene-oTjgan mixtlU'es, which is contrary to experience 'tri th other combustibles. ':10 clea.r up some of t!le reported discrepancies, the authorn have icvestigated the igni tion temperatures of acetylene both in air anri oxygen, and their results are presented in this report.]

Jan 1, 1941

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

By I. AITKENS

The opal , long in disfavor because it was considered " unlucky, " has become much more popular in recent years . For variety and beauty of color the precious opal is without a peer . These colors do not come from any chemical constituent but are produced by structural peculiarities , which in varying degrees deflect the light rays entering the stone and give a prismatic play of hues .

Sep 1, 1931

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By F. H. Gibson

In recent years physico-chemical techniques have been applied for rapid analysis of coal and coke ash as replacements for classical wet-chemical methods. Although the classical methods are accurate, they are time consuming because many chemical separations are necessary to complete an analysis, and they require skilled analysts for accurate work (12).4 For the past several years the Bureau of Mines has applied some of the newer physico-chemical techniques in its continued search for new and improved methods at analysis. The methods of analyzing coal and coke ash evolved from this work include spectrophotometric methods far SiO2, A120, , Fe203 , TiO2, and P2O5; chelatometric titration for CaO and MgO; and flame photometry for Na20 and K2O. The methods are rapid and direct, are suitable for analyzing a group of samples at the same time in production work, and dire results with almost the same accuracy as classical procedures. With the new methods, complete analyses in duplicate can be obtained at a rate of 2 to 3 times that of conventional methods.

Jan 1, 1962