Search Documents

By Tuncel M. Yegulalp

This final report contains the results of all work performed under BOM Grant J0333905. A preliminary systems analysis of coarse-particle coal slurry pipelines as a haulage method for longwall mining systems was performed. Two exhaustive literature surveys on state-of-the-art longwall mining and slurry transport technologies were prepared. Two representative longwall systems were designed, one with conventional haulage and one with slurry haulage. These two systems were then compared on the bases of cost, safety, and reliability. The conclusions were that for the case of a two-face longwall mine, a coarse slurry transport system does not have a clear-cut cost advantage over a conventional (conveyor-hoist) system. However, indications were that a cost advantage could occur under different analytical conditions such as: (1) a larger scale mine, (2) if intangible benefits were quantified, and (3) if new generation technology rather than currently available technology were applied to the study. Budget and time constraints prevented exploration of these conditions.

Jan 1, 1982

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972

By Oliver C. Fursman

The Bureau of Mines undertook this investigation in order to determine the feasibility of producing commercially acceptable alumina and iron by application of the Pedersen process to high-silica, high-titania, ferruginous bauxites of the Pacific Northwest. Calcium aluminate slags were produced by smelting bauxite with coke and lime in an electric-arc furnace. Over 90 percent of the total alumina can be extracted by sodium carbonate solution from slags of properly controlled ternary-phase composition (CaO-Al203-SiO2) that are cooled slowly enough to permit adequate crystallization of the 2CaO-SiO2 and the calcium aluminate compounds. Most of the iron charged was recovered in the regulus; the slag contained about 2 percent iron (as iron oxide), regardless of smelting time.

Jan 1, 1968

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By J. S. Dunning

One Federal Bureau of Mines research goal, to minimize requirements for domestically scarce mineral commodities through conservation and substitution, can be accomplished by utilizing more abundant elements such as iron, molybdenum, and titanium. An example of this research is the study of precipitation-hardening, iron-base alloys containing molybdenum and titanium, as substitutes for the high-tonnage stainless steels that are high in imported nickel and chromium. The precipitation hardened iron-base alloys are strengthened by a dispersion of the ternary Laves phase, Fe2 (Mo, Ti). Aluminum and chromium additions changed the solid solubility limits of molybdenum and titanium in a-iron and affected the composition of precipitating phases. A baseline composition of Fe-7Mo-2Ti was selected to study the effects of aluminum and chromium additions on the precipitation-hardening mechanism and microstructure and was also used in studies of mechanical properties and oxidation resistance. The study yielded workable, precipitation-hardening alloys, with elevated temperature strengths equivalent to or superior to types 304 and 316 stainless steels. Chromium and aluminum additions in combination were more effective in providing oxidation resistance than either addition was alone.

Jan 1, 1980

By P. G. Pigott

The lack of technical information regarding the physical characteristics of kaolins and bauxitic kaolins, rejected during the mining of bauxite near Eufaula, Ala., has retarded their commercial utilization. This investigation was undertaken to determine their behavior when used in refractories. Ores were evaluated as refractory raw materials by compounding dry-press mixtures and specialties following procedures common to the industry. Products now on the market were used for comparison in laboratory evaluation.

Jan 1, 1959

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By Daryl R. Tweeton

This Bureau of Mines publication ill scribes present practices of making injection wells for in situ uranium leaching. Casings, screens, drilling fluids, coring, logging, cementing, and developing are discussed with the objective of aiding those who are starting an in situ leaching operation. Improper choices of materials or techniques can result in wells that are either useless or wells that have an undesirably high resistance to injection. Important factors include careful selection of screen slot size, use of logs for choosing the cementing basket depth, proper cementing techniques, and careful choice, use, and flushing of drilling fluids. The information was obtained through observation of well construction and through discussion with in situ leaching companies, drillers, and suppliers.

Jan 1, 1978

By E. D. Palmes

Phase I of these studies demonstrated the feasibility of measuring the efficiency and capacity of sorbents in tube-type samplers for contaminant gases. This was accomplished by measuring concentration at various points along the length of the diffusion path during sampling. Concentrations were measured by removing small aliquots with gas-tight syringes and gas chromatography. With hexane as the gas and activated charcoal as the sorbent the procedure was quite successful and we proceeded with Phase II of the study; this involved application of the principle to gases of importance in diesel exhaust using a variety of sorbents. When we worked with high concentrations of the test gas we clearly demonstrated the differences in both efficiency and capacity of the sorbents for each of several gases. The chief drawbacks of the system were that we were unsuccessful in determining more toxic gases at realistic occupational exposure levels or determining formaldehyde at any level using the flame ionization detector. It was concluded that, although the method is feasible, more sensitive methods of measuring concentrations of gas in the tube must be developed to make the procedure applicable to regions of chief industrial hygiene interest.

Jan 1, 1983

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

Illumination hardware developed in conjunction with previous Contracts H024202l, H0242049, and H0242023 had not been adequately tested in actual underground work situations. The purpose of this contract was to install and monitor this equipment on mining machines and in actual working places of coal mines to gain experience with the use of the lamps and support equipment in the abusive and critical environments for which they were intended. The equipment that was to be tested consisted of the following: a. Lamps -A variety of sizes of permissible fluorescent lamps which operate from 12 volts DC power. These include the following sizes: Model 8, (9 watts) 2" diameter; Model 15/2 (14 watts) 2" diameter; Model 15/3 (21 watts) 3" diameter; Model 20 (25 watts) 3" diameter; Model 30, (28 watts) 3" diameter; and Model 40, (39 watts) 311 diameter. Representative photographs of these lamps are shown in Figure 1-1 and 1-2.

Jan 1, 1976

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By Clyde L. Brown

The ignition source of fires and explosions in coal mines is sometimes difficult to explain because resulting widespread destruction often erases valuable evidence that might reveal the cause. However, through years of experience, investigators have been able to piece together enough evidence to establish the reasons and, thereby, have been equipped to recommend corrective or preventative measures. The pattern of hazards is not constant. It changes with the development of new practices and new equipment. Important among the new hazards to coal mining are those introduced by electricity. In addition to the dangers of electric shock, fires and explosions from heat and arcs, and premature blasts, certain others have developed as a result of stray electric currents from direct-current traction systems. The conventional direct-current power-distribution system in coal mines is conducive to electrolysis damage to mine tracks, metallic pipelines, grounded power conductors, and structures in a position to become conductors of stray currents. The voltage drop resulting from power demand on intentionally grounded power conductors and accidental grounds on insulated conductors are common sources of stray currents in coal mines. Uncontrolled electric cur-rents flowing through the earth and metallic structures can be a menace, and these contribute to the estimated $6,000,000,000 annual loss caused by corrosion. The purpose of this publication is to discuss some of the electrolysis hazards in the coal-mining industry and to outline corrective measures to alleviate them.

Jan 1, 1962

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By Alfred V. C. Meyer

A Blastcorder4 was calibrated on the Bureau of Mines shaking table in the frequency range of 12 to 40 c.p.s. and in the amplitude range' of 0.25 to 1.0 g. The results of this calibration study show that in the frequency range of 12 to 30 c.p.s. the average accuracy of the Blastcorder is approximately ± 0.1 g.

Jan 1, 1962

By H. D. Kline

This paper is one of a series being prepared by the Bureau of Mines on methods, practices, and costs in various mining districts in the United States. The paper describes mining and ore recovery methods common to the Batesville manganese district, Independence County, Ark., and gives the costs of producing merchantable ore by three operators whose methods were more or less typical of those of many other local manganese producers. The operating costs reported were those of Leonard Baxter at mines on Brooks Hill for the calendar year 1958 and Arkansas Mining and Exploration Corp. at Section 16 mine and the Searcy group of mines and Miller-McGee Corp. at the Diener mine during the first 6 months of 1959. Manganese are was mined in the district as early as 1849 and almost continuously thereafter until August 1959, when termination of the Government's domestic manganese purchase program resulted in complete cessation of mining activity. During those years, production came from more than 189 mines and properties, of which only a few produced as much as 30,000 tons of merchantable ore.

Jan 1, 1962