Search Documents

By Steven V. Crum, David E. Siskind

In response to its own concerns and those of the public, industry and regulatory agencies, the Bureau of Mines is studying the impacts of low-frequency blast vibrations on structures. Previous research has identified potential problems associated with low-frequency ground vibrations and also found that their existence was not particularly rare, given large surface mine blasts and certain geologic conditions. Only a limited amount of data existed in the blast vibration literature on structure response to ground-vibration frequencies below 6 Hz.

Jan 1, 1993

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Mark S. Stagg, Steven V. Crum

The Bureau of Mines is conducting research to develop methods to control fragmentation and improve productivity in surface mine blasting. As part of this research, PRONT02D, a two-dimensional finite element computer program developed at Sandia National Laboratories, was employed to model the fragmentation produced from RS-50, a single hole, reduced scale bench blast in a massive dolomite. The fragment size distribution obtained from the computer simulation was calculated using a submodel that utilizes the crack density and nominal flaw size values computed by PRONT02D.

Jan 1, 1989

By Jack Eloranta

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this case study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By Mark R. Fritzen, Ted A. Fritzen

Anytime that blasting operations will be conducted near existing inhabited structures, vibration damage claims are a major concern of the blasting contractor. It has been our experience that even when vibration and airblast levels generated from a blast are well below accepted damage thresholds, damage claims can still arise. The single greatest source of damage claims is the element of surprise associated with not knowing that blasting operations are being conducted nearby. The second greatest source of damage claims arise from the inability to produce accurate and detailed records of all blasting activity which provides evidence that vibration and air blast levels from each blast had been taken by seismic recording equipment.

Jan 1, 1994

By Zhang Zhenyu, Wu Xinxia

The blasting quarrying technology of rock material of rock-fill dam is one of the more complex problems in the field of engineering blasting at present. The Kuz-Ram model is not suited to predict fragmentation distribution under the geology condition of Tianshengqiao(TSQ) fist-step power station. The modification of kuz-Ram model is discussed. With reference to the idea of model establishment of Kuz-Ram model and according to the results of experimental blasting in-situ, two fragmentation prediction models-TSQ-1 and TSQ-2 model are presented which are adapted to the particular condition of rock material querying blasting of rock-fill dam with concrete facing of TSQ first-step power station. The rapid judgment method of qualified grade material and the method of optimizing blasting parameters are also presented in this paper.

Jan 1, 1998

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d'Or, Québec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Roger Lucas, Dale Nies

The McLaughlin Mine is an open-pit disseminated gold mining operation. Homestake Mining Company's approach to solving some of the blasting problems inherent to this type of deposit provide an interesting case history. Geology, although unique and site specific, is overall similar to other mines within the Western United States over-thrust belt and demonstrates an excellent example of the blasting conditions and requirements common to most of these operations.

Jan 1, 1990

By U. Prasad

This paper summarizes the investigation carried out on a wide range of rock types, subjected to high velocity impact to simulate explosive action. A Split- Hopkinson Bar apparatus was used to generate the high velocity impact. The rock samples included both homogeneous and isotropic, and anisotropic types. The strain rate achieved was between 600 and 12OO/sec, The respective measured dynamic compressive strengths were compared with their low strain-rate or static values. It was found that the ratio of the dynamic to static values ranged between 2.5 and 4.6. It was also determined that the high strain-rate loading produced finer fragment size distribution than the static loading. The fragment size distribution from the two strain-rate regimes has been further analyzed to establish correlation with rock types and the strength characteristics. The results also confirm that high strain-rate loading (i.e. high detonation pressure and high velocity of detonation in an explosive column) would significantly affect the degree of fineness in a blast.

Jan 1, 2001

By Lon Santis

Although unproven, it is suspected that there have been eleven locations since 1988 where explosive generated carbon monoxide (CO) gas moved through the earth and accumulated in nearby underground enclosed spaces. This paper summarizes the incidents, which involved about 30 suspected or medically verified CO poisonings and 1 fatality. Ten incidents occurred in residences and one occurred in a manhole. Although practically nothing is known about the mechanism behind the suspected gas migration, review of the incidents and available information indicates there are certain warning signs and a successful remediation technique available. In each case, overburden heavily confined the explosive in the blasts, preventing release of explosive-generated gases to the atmosphere. All the blasts were in residential areas, and none were excavated immediately. Where the distance from the blast was recorded, 5 of the blasts were within 20 to 50 feet (ft) (6 to 15 meters [m]) of the underground enclosed spaces, 3 were 100 to 150 ft (30 to 46 m) away, and 1 was 400 to 500 ft (120 to 150 m) away. Investigators often identified suspected pathways from the blast site into the underground enclosed spaces. One technique appeared successful at quickly correcting an existing condition. This technique involved applying negative pressure to the earth and removing the CO from the ground surrounding the underground enclosed space.

Jan 1, 2001

By Ken C. Pruss

Seismic studies have proven that the frequency with which shock or vibration waves are reacting on a structure, in correlation with the amplitude of those waves, has a definite affect of structural damage. Different structures will react to different frequencies. In the past few years, some major coal producers in the midwest United States have shown that with the use of highly accurate detonators and exotic timing patterns they have effectively been able to adjust frequencies and this has enabled the operators to continue their excavation of overburden in environmentally sensitive areas.

Jan 1, 1989

By Leslie Taylor, W. Fourney, Uli Leiste

This paper presents the results from a series of tests conducted to investigate the total vertical impulse delivered to a target plate by a buried explosive charge. The tests were conducted at a very small scale but previous work has shown that small scale testing can predict impulse applied to plates in full scale. Non-deforming plates were used to determine the change in impulse delivered to targets as a result of changes in standoff distance and burial depth changes.

Jan 1, 2009

By C. Pelley, S. Kelebek, G. Kunzel, P. Katsabanis

Small blocks of granodiorite have been subjected to blast loads from a single borehole and from a series of boreholes detonating at various timing intervals. The damage of the blocks was assessed through P-wave velocity monitoring, measuring the change of the point load strength index of the rock after dividing the large blocks into smaller ones and measuring the work index of the material at different distances away from the blasthole. Numerical modelling with the AutodynTM code enabled visualization of damage. It was shown that damage is optimum at a small delay time between successive holes while it drops rather drastically after this point.

Jan 1, 2003

By Edward J. Walter

Vibration control is affected by many factors which are difficult to isolate and evaluate. Occasionally a circumstance occurs in which one factor appears to predominate and its effects can be evaluated. Changing rock characteristic or lithologic variation is one of these factors or parameters. In a recent seismic monitoring project, lithologic variation in the form of hard lenses occurring suddenly and randomly in the rock to be excavated caused sudden and large increases in vibration level. Data are presented to illustrate these effects, and procedures used to control these effects are described.

Jan 1, 1981

By Tapan Goswami, Geoff Keith

"At Bulga Coal, the objectives of drilling and blasting are to maximise safety and to minimise the totalcost of mining. A recent audit of two overburden blasts established that the standard of drilling and blasting is excellent. No apparent hazards were identified. Laser profiling showed that highwall free faces are reasonably planar with some exceptions, thereby promoting uniform burden distances along front-row charges. However, in three isolated areas along one face, small burden distances existed. The mean and the standard deviation of errors in the collar positions of front-row blastholes was found to be 0.3 + 0.03 m. A borehole video camera was used to show that blastholes did not feature open bedding plane partings, cavities or damage produced by the blast in front of them."

Jan 1, 1999

By Chantale Doucet, Yves Lizotte, Alan Cameron

A joint Federal Government-Industry research project on the effect of geology on the fragmentation of rock excavated by blasting in underground developments was conducted at the CANMET Experimental Mine, near Val d’Or, Quebec. A total of thirteen (13) blasts were studied from November 1994 to February 1995. The analysis of each blast was divided into three stages: pre-blast characterization, including structural mapping, assessment of Rock Mass Ratings (RMR), Tunneling Quality Indices (Q), blast design documentation; blast characterization comprising blast vibration monitoring and analysis; and post-blast assessment comprising fragmentation assessment by digital photoanalysis, calculation of half cast factors and measurements of bootlegs.

Jan 1, 1996

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By Walter Voglauer, Elisabeth Zechmeister

Description of Project: The four photos show a chimney blasting operation in Vienna’s district of Floridsdorf on May 4 2011. The blasting was done with two types of charges. An internal charge provided a force of blast which resulted in 135 single electrical blasting caps initiated detonations on the basic ensured the straight collapse of the chimney. The preparation work was done by reserve force military engineers. The series of photos were shot by Elisabeth Zechmeister. She works in the Austrian DOD but not as a professional photographer; much more she did all activities in her spare time.

Jan 1, 2013

By James Ludwiczak

This paper consists of the conduct of a forensic criminal investigation of the components, construction, use, and functioning of two suicide bombs. As the title states, the task was to form professional opinions as to whether the bombs would work, would cause property damage, and would injure or kill. The bombs were created and installed by a defendant in a Federal death penalty case where the defendant’s daughter was killed in a shootout with the West Virginia State Police. The two black powder bombs were placed under the front seats of the defendant’s automobile and were designed to function by the use of a toggle switch connected to the automobile’s cigarette lighter. The forensic work first consisted of an inspection of the remains of the wiring system and bombs at the Bureau of Alcohol, Tobacco, and Firearms Laboratory, in Ammendale, MD. This was necessary to determine and detail the wire diameter and lengths, the lengths and size of the wire used, the type of toggle switch used, the type of containers, the type of rocket motors used to initiate the black powder, the manufacturer and amount of black powder used in each bomb, and the type, wraps, and amount of duct tape used for the construction of each bomb. Using this data, tests were conducted by duplicating the wiring system and the two bombs to insure that the system functioned properly. Each bomb was duplicated and initiated to observe the violence produced when initiated in the open air. Duplicate bombs were placed under the seats of a similar type of automobile and initiated. The purposes of the tests were to duplicate the bombs, to observe the violence of the initiation, and to observe the damages to the automobile produced by the initiation.

Jan 1, 2007