Search Documents

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-theart, custom designed x-ray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. For example, a packed bed of coal particles is shown below in which different crystalline froms of pyrite are distinguished in 3D.

Jan 1, 2003

By Heinrich Hutchison, Thomas von Moltke, Roelof F. Sandenbergh, Katarina P. Cerovic

Although the cyanidation process for gold leaching has been applied for more than a hundred years, some aspects of it, such as the passivation of the gold and the depassivating action of heavy metals, are still not well understood. In this work the anodic behaviour and surface composition of gold in alkaline aqueous cyanide with lead additions were investigated using polarization experiments and XPS. It was found that lead in the solution activated the gold at low concentrations, somewhat more positive than the reversible potential for gold, but that the activity again decreased at higher concentrations of lead. The potential range for the activation of the gold coincides with that where underpotential deposition of lead occurs, i.e. –200 to –600 mV(SCE), as indicated by the surface composition of the gold, shown in figure 1. Note that the concentration of lead on the surface of the gold only increased with time in the bulk plating potential range for lead, where gold is not activated by the presence of lead. It is also shown that up to 20 mg/L of lead added to the solution will activate the gold, provided that bulk plating of the lead is avoided. It is also important to avoid reducing conditions during leaching, where bulk plating of lead may occur, if the gold is to be activated by lead to achieve a high leaching rate, as the bulk plated lead screens the surface rather than activating it.

Jan 1, 2003

By Victor Avdokhin, Valery Morozov, Valery Stolyarov

"The adaptation-determination method provides for keeping given relationship between concentrations of ionic and molecular components of a pulp liquid and correction of parameter of the model on the basis of analysis of ore composition, technological parameters of flotation, and cost of valuable components.• optimisation program “ADDEFLOT” and combined analyzer of pulp “RA-931”An adaptation-determination method provides for two-level control of bulk and selective flotation of polymetallic ores. The lower level provides for control of reagent dosing on the base of control of ionic composition parameters in the pulp liquid phase. The control goal is to keep the basis relationship among parameters of ionic composition (ions A, B, C) in pulp liquid phase given by equations of type:• alg[A] + blg[B] + clg[C] = K (1)Values of a,b,c coefficients are uniquely determined by a physico-chemical model used. Kind of the model depends on mineral composition of an ore and reagent regime applied. As parameter of ionic composition, also values of one or two parameters (or their combinations) can be used, for instance, pH, concentration of sulfide ions, ions of collector.The upper level of control is based on calculation and use of technological results of selective flotation. At the level, an adaptation of the model (1) is conducted. A principle of the adaptation is in determining (and including in pre-setting function of the lower level) such value of K parameter, at which maximal economic effectiveness of the process is reached. As a criterion of economic effectiveness of the process, a function of losses of several valuable components, taking into account cost of the metals lost, is used. For 2-component ore, in simplified form, the function is as follows:"

Jan 1, 2003

By D. W. Fuerstenau

Understanding how cationic surfactants affect the interfacial behavior of quartz is important in mineral processing and environmental engineering. This paper presents the results of a study of the effect of the molecular structure of cationic surfactants on the interfacial behavior of finely ground natural quartz. Most of the experimental work involved the determination of zeta potentials and the stability of quartz suspensions. Some measurements of induction times and the flotation response of coarser particles are also included. How these surfactants affect interfacial behavior is discussed in terms of adsorption mechanisms. The molecular structure (number of hydrocarbon chains, type of ionic head group, number of ionic head groups on the molecule) of these reagents was found to significantly affect their surface activity.

Jan 1, 2014

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin.The use of selective ion exchange to recover metals from sulphuric acid liquors has been studied for a long time. Companhia Vale do Rio Doce (CVRD) has been actively involved in hydrometallurgical applications of IX and has researched in selecting the optimum resin for nickel and cobalt selective removal and the design of a suitable IX circuit. When an IX operation is contemplated for a specific application, it is followed a screening process which generally involves consideration of the solution composition and pH, speciation of the metals in the liquor to be treated and other possible techniques that can be applied to achieve the desired specifications or recoveries. Once a decision has been made to use IX for a specific application, relevant testwork should be done to select the most cost-effective resin and design the IX circuit to achieve the desired criteria. The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to-solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment"

Jan 1, 2003

By Kobus (J. J. ) Rossouw, P. Chris Pistorius, Johannes Sono

"Different coal properties are important in SL/RN (coal-based rotary kiln) direct reduction of iron ore, and in electrical smelting of prereduced iron ore. Laboratory simulation was used to evaluate two candidate coals, which were similar in volatile content and rank, but differed in reactive maceral content. The tests served to evaluate both the reduction rate (during direct reduction) and the dissolution rate of carbon from the coal into an iron bath.Reduction rates of mixtures of magnetite and devolatilised coal were assessed isothermally, using samples of 55 grams. The off-gas analysis was used to follow the extent of reduction. Results are shown in Figure 1 a). Coal B was expected to be more reactive, based on its higher content of reactive macerals (77%, compared with 61% for Coal A). In line with this, Figure 1 a) does show a higher reduction rate with this coal. However, increasing the reduction temperature increases the reduction rate substantially,especially for the less-reactive Coal A.For the dissolution experiments, samples (mass: 250 g) were melted in an alumina crucible (under a nitrogen atmosphere), to give a starting composition around 1%C. When the desired temperature was reached, 25 g of char was added on top of the melt, through a feeding port. Results are shown in Figure 1 b). The more-reactive Coal B was less crystalline (the graphite crystallite size estimated from X-ray diffraction was 4.6Å, compared with 11.4Å for Coal A). This is associated with a lower dissolution rate in iron."

Jan 1, 2003

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

"INTRODUCTIONThis paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.OPTIMISATION MODEL FOR LINKING DESIGN TO RECYCLINGImproving the efficiency of the material cycle of the car is essential to ensure a sustainable development of our society as well as e.g. to comply with the recycling targets imposed by EU legislation. In the design of the car various materials are combined and connected in many different ways, making up the complex 'mineralogy' of the car and its components, which is changing rapidly and continuously over time. The liberation of materials during shredding plays an important role in the composition (and quality) of the intermediate recycling streams. In order to include the influence of product design (mineralogy), liberation, and particle composition (quality of the intermediate recycling streams) in the optimisation of the recycling of end-of-life vehicles, a systems engineering tool for optimisation of the recycling of end-of-life vehicles was developed, including a liberation model. The optimisation model predicts the recovery rate as a function of product design (in this case a car), liberation, efficiency of the different process steps, economy and legislation based on a developed recycling flow sheet for end-of-life vehicles. Optimisation can only be achieved through the combination of the knowledge areas of product design, shredding, mechanical separation technology linked to pyro- and hydrometallurgy, composing a complex interconnected network of unit operations."

Jan 1, 2003

By Claudio L. Schneider, Reiner Neumann

Any serious study of stereological conversion procedures must be based on an as accurate as possible complete fractionation of a real mineralogical texture. The original work on the Dolomite- Sphalerite Magstream? separation provided excellent data for establishing a working stereological conversion procedure, which has been successfully applied to a number of ores since its implementation. The linear grade distributions measured from these fractionated particles have been published and are accessible. The procedure for stereological conversion from areal measurements is exactly equal to the procedure for linear measurements. Particle composition from the dolomite-sphalerite density-fractionated particle sets, derived from both linear and areal data (Figures 1 and 2, respectively) are redundant, after proper transformation, and match the particle’s compositional range (plotted against S.G.) expected from Magstream?; direct density measurements by Hemicropicnometry plots within the ranges. Linear data cannot be used without conversion, but areal measurements are often directly applied as liberation spectra. Our areal measurements, without stereological conversion (Figure 3), differ completely from the results after transformation, and its density range falls mostly out of the expected/measured values. Therefore non-transformed areal data cannot be directly applied as useful liberation information.

Jan 1, 2003

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By M. Brennan, A. Majumder

"The mineral processing research community has devoted enormous efforts to the modelling of mineral separators over the last 50 years. While many efforts have been made to use only fundamental physics as a basis for the models, fluid flow patterns in separators are not simple while the motion of particle swarms through fluids is extremely complex.Sluices are the simplest forms of the flowing film concentrators and have been used in the mineral industry since at least the 15th century (Agricola, 1556). Flowing film concentrators, in general, still have widespread applications in the mineral industry and their designs vary according to the specific need.Particle separation in a sluice appears deceptively simple, but the separation mechanism has proven complex and difficult to quantify. Separation in the sluice takes place in a flowing film a few millimetres thick. The particles are suspended by turbulent eddies and motion relative to the fluid takes place in socalled hindered settling mode. The difficulty arises because the presence of the particles influences the flow pattern and when the particles are fully transported by the flow, the flowing slurry may not have the same viscosity as water and does not have the same density. For this reason a universal theory which can explain the behaviour of a suspension in a sluice or any other gravity equipment has still not been developed. Few attempts have been made to analyse the mechanisms involved in the concentrating processes of pinched sluices and Reichert cones.Fluid flow behaviour and slurry transportation characteristics in open channels have, however, been active research topics in the disciplines of fluid mechanics, chemical engineering and civil engineering for many years. As a result, an extensive literature is available, which has led to the development of the model described in this paper.In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass beads at various particle concentrations and flow rates, and the actual particle separation taking place compared to predictions from modelling.The modelling strategy was divided into two parts; the first was to predict the horizontal slurry flow velocity profile and the second to predict the solid particle concentration over the depth of the flow at different flow conditions. The predictions were then validated with measured data sets. This can easily be done if the slurry flow is split at different fractional flow depths so that the mass flow of solids over different flow heights is measured accurately over a fixed period. Mass flow splits can then be calculated by integrating the product of the predicted slurry velocity profile and the predicted solids concentration profiles from the base of the sluice bed to the slurry free surface."

Jan 1, 2003

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Bertil I. Pålsson, Sture V. Persson, Kent T. Tano

"Autogenous (AG) and semi-autogenous (SAG) mills often operate in an unstable state because of the difficulty to balance the rate of replenishment of large ore particles from the feed with the consumption in the charge. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behaviour of the mill charge. A problem in attempting to measure those parameters is getting a sensor that is both robust and sensitive enough for continuous on-line measurement.Techniques that measure the force acting on the lifter when it hits the charge inside the mill have got an increased interest recently because of the ability to combine it with DEM modeling. This paper presents a method for the measurement of the apparent filling level in a pilot ball mill equipped with the Metso Continuous Charge Measurement system (CCM). In this technique a strain gauge sensor is mounted on a flat steel spring which is fitted into a recess underneath a lifter bar. In addition, a conductivity probe, the Boliden Grinding Measurement System (GMS), is mounted in another lifter bar with the purpose of comparing the two measurements. To visualise the behaviour of the charge a 2D DEM modelling technique is used with Metso HFS software.The pilot mill is a grate-discharge mill, equipped with 12 rubber lifters of square size 0.1 m, face angle 45 degrees. Steel balls in the size range 10-30 mm and density 8000 kg/m3, are used in the experiments. Test material is a hematite pellet feed, d50 around 45um, chosen to get stable grinding conditions with respect to feed size variations.The experiment is meant as a first test of the equipment’s performance, and to study how the sensors respond to changes in some operating variables. To get an understanding of, and distinguish between correlation and causality, experiments are performed according to a full factorial design with two levels, and in addition two replicates of the experiments at a center-point in the charge level setting."

Jan 1, 2003

By Markus A. Reuter, Albert Scholte, Ewoud V. Verhoef, Gerard P. J. Dijkema

"A dynamic, interactive map has been developed of the life cycle of a number of metals, from mining through to minerals processing, metal production, product manufacturing, recovery and waste management. Whilst the existing metal process network and waste management infrastructure provide substantial scope for (product) design, these also limit change because of the strong path dependency of industry and infrastructure development. The metal production network is complex, as it consists of an interconnected and integrated system that incorporates multiple production routes for a spectrum of metals. More often than not, the production or recovery of a single metal is related to or dependent on the generation or recovery of another. The effects of these other metals is of great importance. In order to realize the potential economic importance of impurities, research and development have integrated the processes of copper production with those of lead and zinc, and connected the processes to those of among others silver, bismuth, tin and platinum group metals (PGMs), for example. The recovery of these elements from the interconnected circuits is extremely complex, as most of the elements must be circulated between two or more circuits before they are concentrated enough to make their extraction possible, and their recovery as a compound profitable.From such a system’s perspective, it can easily be seen that a complication for solid waste management has arisen through the development of products (consumer goods) that bring together metals that are not linked in natural resources. As a consequence, many of these materials are not compatible with any process in the metals production network that was developed for the processing of primary, natural resources, optimized for the processing not only of the primary metal but also for all mineralogically associated minor valuable and harmful elements. The formation of large or complex residue streams or undesired harmful emissions then inhibits processing and recovery of said products at their end-of-life. Another complication is that any change to the system (in metal production, SWM or product design) affects the system configuration. Due to the changing demands for metals as a result from the changing products made from the metals for example, the relationships between the processes in the interconnected metal production systems change. This affects both the demand for old scrap (required amount and grade) from waste management, and the environmental profile of the metals. Preferably, therefore, product designers, waste processors and metal producers must cooperate to realize optimal metal recovery in processing discarded consumer products."

Jan 1, 2003

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By Milind Sabne, Pradip, P Kapur, Beena Rai

"The efficiency of an industrial flotation circuit depends on (a) the selectivity and the kinetics of the reagent combination selected for the separation (b) the hydrodynamic conditions prevailing in the flotation cell (essentially equipment design parameters) affecting both the pulp and froth phase (c) the operating parameters such as feed rate, pulp density, pH, temperature etc. including the mineralogy, particle size distribution and relative proportion of liberated and composite particles of constituent minerals in the feed to flotation circuit and (d) the circuit configuration itself. We have developed a molecular modelling based reagent design and selection framework to assist mineral engineers to arrive at the preferred reagent combination based on a rigorous, scientific and quantitative comparison of various options available for this purpose. Similarly we have also utilized a general circuit design methodology proposed by Kapur and Mehrotra in 1974. The advances thus made in modelling both the reagent chemistry as well as circuit design, along with the availability of sophisticated, automated tools for characterization of ores (liberation as well as mineralogical composition of the different flotation streams) provides a scientifically rigorous, quantitative, robust framework for design and optimization of complex flotation circuits. We illustrate in this paper the power and the utility of our rigorous optimization based approach to designing industrial flotation circuits for the beneficiation of a multi-component feed with the help of few case studies from our own work. With the proposed methodology, higher levels of process efficiencies can be achieved in the industrial flotation plants, in particular those processing complex, multi-component feeds requiring multiple stages of flotation separation. We are currently developing an IT platform consisting of computer-aided decision support tools for arriving at the preferred flotation circuit and the appropriate reagent chemistry for a given ore deposit and/or a given plant."

Jan 1, 2014

By Bronwynne K. Williams

"In deriving flotation kinetic models, the froth phase was, until recently, either ignored or treated entirely empirically. The behaviour of the froth is now known to be usually important and sometimes dominant in determining flotation performance. Hence numerous methods have been developed for sampling the flotation froths and models incorporating the effects of the froth behaviour have been derived.Such models will assist in determining more accurate estimations of the kinetic parameters utilised in the designing of industrial scale plants thus reducing the incurred costs of over designing. In particular, improved models for batch tests may lead to more effective use of batch testwork for prediction of continuous plant behaviour. A more detailed model is thus proposed which allows for a more realistic approach to the flow distribution in the froth phase.PROPOSED MODELThe batch flotation process is split into two stages in time, namely before the froth begins to overflow and after. The assumptions made, and hence the calculations, are different for each stage.The air enters the slurry at t=0 and generates froth. The superficial velocity of the air through the cell is given by go. It is assumed that the rate of froth breakage (gb) is constant during the first stage. The froth rises with a uniform net velocity throughout the cell and no mixing is assumed to occur.After the froth begins to overflow, the velocity distribution of the gas is modeled by segmenting the froth phase as shown in Figure 1. A model for bubble breakage rate or measurements of froth velocity allows one to obtain the volumetric rate of concentrate froth production. The entrained water and associated particles and a drop-back mechanism are also allowed for in the model."

Jan 1, 2003

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By H. Pearce, A. E. Lewis, A. Ochieng

Hydrodynamics and mixing are fundamental to the operation of mineral process systems such as flotation cells and metal precipitation reactors. The computational fluid dynamics (CFD) technique has been employed in the present work to study the hydrodynamics in a mixing vessel stirred with either a Rushton turbine or a pitched blade impeller. The multiple frame of reference (MFR) approach has been used to model both impellers. A draft tube was used only in the Rushton turbine stirred vessel. The flow profiles for the pitched blade impeller have been studied in three regions; below the impeller tip, at the middle of the tank, and near the liquid surface. The simulation results were compared with literature data obtained using a laser Doppler velocimetry in the three regions of the vessel, and it was found that the model predictions were better in the impeller region. There was a poor prediction of the experimental results in the region closer to the liquid surface; however, this was improved when the turbulence parameter (C2) in the k-e model was set to a higher value. The value of the impeller clearance at which the Rushton turbine generates an axial impeller type flow has been determined and it has been shown that, at this clearance, a draft tube can be used to enhance axial flow in a Rushton turbine stirred reactor.

Jan 1, 2003

By P. M. Solozhenkin

"Galvanochemical process (GChP)) cleaning of sewages is realized in the field of shortcirquited galvanic elements from the mixture current the materials place in purification’s solution and form multitude galvanopairs without external electric field in presence oxygen of the air. The galvanochemical process is electrochemical process utilizing galvanic pairs: coke - iron, iron - copper and others and process does not require chemical reagents.The effect of basic parameters of the cleaning effectiveness have been studied depending on oxidizing of galvanopairs. Adjusting nature, type of galvanic pairs and forming three component system possible to enlarge emf circuits to 2.378 V.The role of ?2, as basic agent, for generation of hydrogen peroxide and hydroxyl ions.It was stated, that removing of metal ions from solutions occur mainly on account of sorption and hydrolytic sedimentation of iron oxihydrates.Determined separate stages of the process: coagulation, sorptions of admixtures on freshly formed ferric oxides and oxidizing destruction of organic components of effluents in presence of ?2 ? ?2?2. Shown efficiency of the method for removing of Cu, Cr, Ni, Zn, As ions, as well as fluoride, phosphate and cyanide anions and oil products, surface-active and flotation reagents. Cleaned water can be recycled for some processes non-critical toward residual concentration of admixtures, as total salt contents is lowered on 60-75 % and reaching limits of concentration for toxic components.The concept of high power unit creation was developed, and galvanochemical pulsator is presented. The pulsator is not expensive, and exploitation expences are low, as well as servise is simple with high effectiveness, and capacity. The galvanoflotation process is developing, combining galvanochemistry and flotation of hydrofobic admixtures (oil, surface-active agents).The galvanochemical flotators are presented."

Jan 1, 2003