Search Documents

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By S. Akhlaghi

In many electronic/optoelectronic devices, interaction between the metal stack and solder is undesirable. If a reaction happens, a nonuniform joint containing spikes and voids is likely to form and as a result the heat dissipation deteriorates significantly, which in turn, leads to the degradation of the bond. In the present work the interaction between Ti/Mo/ Au metallization system, which was sputter deposited on AlN substrates, and Pb-Sn solder was studied by using scanning electron microscopy (SEM). Also, an EDX system was used to trace the changes in chemical composition of the layers after solder tests. The microstructural examinations show that the Ti and Mo layer from the Ti/Mo/ Au metallization system are not impermeable enough and thus Ca from the surface of the substrate moves all the way up to the interface of Au/Mo and forms an intermetallic at the interface, which grows over time.

Jan 1, 2006

By K. Oishi

We have developed a 76Cu-3Si-21Zn alloy "ECOBRASS®" containing no lead. When 3% Si is added to a 78Cu-22Zn alloy, kappa and gamma phases participate uniformly in the alpha matrix. When being machined, stress concentrates on these hard phases, namely kappa and gamma, and thereby lowering the required cutting force and yielding segmentalized chips without lubricant. Kappa and gamma phases transform into beta phase under high temperature, which makes it easier to extrude and/or forge the alloy. When 0.08% P and 50 ppm Zr are co-added, the grains of ECOBRASS® castings are refined significantly to become as small as several dozens of micrometers. The grain refinement by the co-addition of P and Zr improves castability, tensile strength and elongation of ECOBRASS® castings. Meanwhile, the lead leachate from an ECOBRASS® water meter, field-tested in pH 6.8 drinking water for one year, was less than 5 ppb without correction. No indication of dezincification corrosion was observed, either. ECOBRASS® is equally suitable for rods, forgings and castings, and makes it possible to produce a complete set of plumbing parts (valves, faucets, etc.) by its own. This way, not only improving recyclability, ECOBRASS® also realizes size and weight reduction due to its good corrosion resistance and high strength.

Jan 1, 2007

By Z. -G. Ren, J. -S. Qian, Y. -G. Yang

The waste slags from chemical and metallurgical plants contain approximately wt 1% water soluble Cr6+. This hexavalent chromium is very harmful to human health, and the treatment of the slags has concerned metallurgists for many years. A sintering method was developed to treat the waste slag. In this process, sinter was made from a mixture of the waste slag containing hexavalent chromium, iron concentrate and coke breezes. During sintering, hexavalent chromium was reduced to trivalent chromium. The latter is known as a non-harmful material and can be used as chromium resource for the production of ferrochromium or chromium-containing cast iron. After sintering the hexavalent chromium in the sinter could be reduced to less than 0.0008%. It was found that the waste slag with fine particles was favourable to the Cr6+ removal. An increase of carbon content in the sintering mixture could increase the rate of Cr6+ removal and the strength of the sinter produced. The rate of Cr6+ removal increased with increasing basicity of the sintering materials with basicity less than B=1.8, above which it decreased with increasing basicity. Blast furnace was found to operate smoothly when using the sinter made from the waste slag containing chromium. However the productivity of sintering machine was slightly low compared to the sintering operation using ordinary raw materials.

Jan 1, 2004

By W. R. Tyson

Pipelines for the transport of gas and oil are being designed to operate at increasing pressures in increasingly harsh environments. The steel used to construct these pipelines must have adequate toughness to tolerate weld imperfections (i.e. withstand bending strains) and to arrest running cracks (i.e. to prevent propagation of axial fractures). The problems posed in specifying suitable toughness parameters and the approaches currently being used to measure them are discussed.

Jan 1, 2005

By Eugene Larochelle

The serpentine of the Eastern Townships of Quebec is more or less seamed and impregnated with chrysotile asbestos, of which we note two types: the cross-fibre and the disseminated fibre. The cross-fibre type always appears in fibres or crystals arranged parallel to one another, and disposed at right angles to the walls of the matrix serpentine. The length of fibre of these veins, which run in every conceivable direction, even crossing ?one another, varies from microscopie dimensions to three and sometimes four and even five inches. It is the principal form of asbestos found in the serpentine of Thetford Mines, Black Lake, Coleraine, and Asbestos. The disseminated-fibre type, which is the main product of the serpentine of Broughton township, in which ate located the mines at East Broughton, does not form veins, but occurs in the serpentine without any definite arrangement. There is a difference in the toughness and hardness of the rock of the two types, the Broughton serpentine being softer than that at Thetford. The disseminated-fibre section of the serpentine belt is probably more regular in its content than is the cross-fibre section. Nevertheless, it contains no 'crude,' which is the most valuable of asbestos, and the fibre is usually shorter than the cross-fibre average.

Jan 1, 1928

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By w. w. Milde

"Since its startup in 1975, the Rabbit Lake mill has been modified (0 process both increased tonnage and higher grade ore. Ore initially came from the Rabbit Lake pit . In 1985, a major mill expansion was commissioned to allow treatment of B-zone pit ore, which is mineralogically and metallurgically different fromRabbit Lake pit ore.Mill modifications, and the changing ore characteristics and processing targets which made them necessary, are described. Mill LocationThe mill complex, shown in Figure I, comprised of milling facilities, acid plant, power generation , warehouse and administration offices, is located approximately 1.5 Ian south of the Rabbit Lake pit, and about 8 Ian southwest of the B-zone open pit mine.Original Milling CircuitOre feed to the mill commenced June 10, 1975. The mill was designed to process 1500 tonnes per day , 483 000 tonnes per year with an average grade of O.44OJo Ups and an annual production of 2000 tonnes UPs' Run-of-mine ore was dumped directly onto a 60 em square opening grizzly. Oversize was broken with an Ingersoll-Rand hydrauli c rock breaker. Minus 60 cm ore was fed to a 6 m diameter by 1.8 m long Hardinge semi-autogenous (SAG) grate discharge mill. Mill discharge was screened over a Tyler double-deck vibrating screen, with screen oversize returned to the SAG mill feed chute via conveyor belt. Screen undersize (minus 2.4 mm) was pumped to 51 cm diameter Krebs cyclones in closed circuit with the SAG mill. Cyclone overflow (about 50% minus 74 micron) was thickened to 55% solids in a 30 m diameter neutral thickener .Thickened pulp was stored in two mechanically-agitated wood stave tanks (5.5 m diameter by 6 m high), to which sulphuric acid was added to obtain a pH range of 1.5 to 2.0. The fmalleaching was carried out in five more identical tanks. Sulphuric acid and sodium chlorate were used to maintain a pH of 1.5 and a terminal emf of -450 to -500 mV. Steam sparge was utilized to obtain a temperature of 45°C."

Jan 1, 1989

By John A. Allan

The subject chosen for this paper is not a new one, but the subject matter is so extensive that something new can always be said .about it. We are just beginning to realize how little is actually known about the character of Alberta coal, except for a few general facts. The object of this paper is not to explain that our previous information, in whole or in part, on the coal resources of Alberta, has been incorrect, but rather to present some new facts obtained as a result of recent study in the field and in the laboratory. As field investigation continues the problem of determining the character of a coal seam for any great distance laterally becomes more and more complex. Our present knowledge of Alberta coal deposits should not be discussed before due reference is made to those great pioneers who blazed the trails for later geologists, by recording their observations on the general geology of Alberta. Geologists, to-day, particularly those of us who are striving, year after year, to unravel the mysteries of stratigraphy, palaeontology, and structure, in so far as these are related to the coal resources of Alberta, fully realize our indebtedness to those three trail-makers, Dawson, McConnell, and Tyrrell. Had these geologists not recorded their observations correctly, nor interpreted the broad geological facts contained in Nature's book, with still uncut pages, how much slower would have been the progress of our coal knowledge in the succeeding years. It is true that many of the interpretations given to observations by these pioneers have had to be changed as a result of closer studies, but we must also expect that the geological interpretation from present day observations will be changed by future workers, as Nature's book is read and re-read.

Jan 1, 1925

By G. A. Davidson, P. G. Williams

"New developments in centrifugal slurry pump technology are discussed in relation to their importance for improving pump operation and reliability.Experimental data obtained by measuring the velocity of liquid flows in a slurry pump casing using Laser Doppler Velocimetry are presented. This demonstrates the importance of selecting pumps with the proper hydraulic design to provide optimum efficiency, maximum part life and minimum operating cost.The paper also discusses the use of new wear resistant materials, such as ceramic/metal composites, which can significantly improve the life of parts exposed to abrasive media. The results of laboratory attrition tests are presented. IntroductionCentrifugal slurry pumps are of primary importance for the hydro transport of abrasive and corrosive media in the mineral processing industry. As for all process equipment, slurry pumps must be carefully selected and operated to provide optimal performance. To achieve this, it is necessary to select equipment which will provide efficient and reliable operation for the specific service conditions and incorporates the best materials available to obtain maximum parts life.Abrasive wear of liquid end components is the most important aspect that distinguishes the design and application of slurry pumps from other types of pumps. It is therefore necessary to have a fundamental understanding of the mechanical interaction between pump components and the media being handled, as this will impact significantly on hydraulic design, mechanical reliability and selection of wear resistant materials. Recent advances in computational approaches'» have greatly improved the prediction of wear rates in pump casings by facilitating the solution of complex equations which describe the wear mechanisms mathematically. In conjunction with this, new experimental techniques allow researchers to measure flow fields in pump casings using non-invasive devices such as Laser Doppler velocimeters."

Jan 1, 1992

By David G. Dixon, Ahmad Ghahremaninezhad, Edouard Asselin

"Atmospheric leaching of chalcopyrite in sulfuric acid solutions is a slow process due to the mineral’s passivation. We have investigated the nature of the passive film in this work. Electrochemical reduction and oxidation of chalcopyrite over the potential range of -0.5 to 1.2 VSHE were investigated in 0.5 M sulfuric acid solution (pH 0.3) at 25 ºC by multicyclic voltammetry and open circuit potential measurement. The influence of scan limits on the evolution of current peaks was studied with both stationary and rotating electrodes. It was observed that the anodic oxidation of chalcopyrite begins at potentials above 0.6 VSHE, most likely by preferential dissolution of iron atoms over copper atoms. The selective electro-dissolution process results in formation of a metal-deficient sulfide passive film (i.e. Cu1- xFe1-yS2, y > x). The passive film dissolves at 0.9 VSHE. Elemental sulfur is one of the products of chalcopyrite dissolution above 1.0 VSHE. Cathodic reactions within the potential region of 0.1 to 0.6 VSHE and anodic reactions at potentials lower that 0.5 VSHE are associated with at least one soluble species from solution. The soluble species involved in the cathodic reactions are likely ferric and cupric, while the soluble species involved in the anodic reactions is likely H2Saq."

Jan 1, 2014

By Michael Loken, April Montera

"The process of blending consistent and predictable feed for the roasters is critical to optimizing product quality and controlling production costs. To assist in this process, Online PGNAA Slurry Analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100% of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their Full Stream, Elemental Slurry Analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced."

Jan 1, 2016

By J. A. Brusset

Introduction The West Canadian Collieries, Limited, operate three bituminous coal mines in the Crowsnest Pass district of Alberta. Two seams are worked; their thickness varies from 10 to 20 feet and their pitch from 10 to 45 degrees. The Bellevue mine was opened in 1903, the Greenhill in 1914; both are gassy and dusty, and at both the haulage is a problem, as the workings are spread over distances of several miles. Compressed-air locomotives are used at Bellevue, rope-haulage at Greenhill, both of which solutions of the haulage problem are costly in installation an operation, and lack flexibility. In 1943, the Adanac mine was opened; and the question soon arose as to which system of haulage should be selected. Compressed-air locomotives and ropes were rejected on the ground of high cost. Since, under the Alberta Mines Act, the use of trolley locomotives underground in coal-seams is not permitted, the choice lay between storage battery locomotives and Diesel locomotives. The preference of the author, who had had experience with both in French gassy coal mines prior to 1930, was for Diesel locomotives, due to lower cost of installation and greater flexibility and reliability. However, Regulation No. 13 of the Mines Act of Alberta reads: 'No gasoline-driven engines shall be used underground in any mine, and no internal combustion engine shall be used underground in any coal mine, except only when authorized by the Chief Inspector in writing, and on such terms as he may prescribe"

Jan 1, 1948

By L. Xia, B. Hart, K. Douglas1, S. C. Chelgani

Development work to optimize a flotation flowsheet for rare earth element (REE) recovery is underway. The original approach used alkyl phosphates and phosphoric acid ester as collectors to concentrate REE minerals. To improve REE recovery, hydroxamates as alternative collectors were investigated. In this paper, micro flotation of REE minerals using salicylic, benzoyl and naphthoyl hydroxamates is reported. Unlike phosphonic collectors, slime removal does not show a significant effect on REE recovery when using hydroxamates as collectors. Among the three hydoxamates, the grade of La, Ce, and Nd for concentrates produced by salicylic hydroxamate is the highest. The recovery response with naphthoyl hydroxamate is similar to that of salicylic hydroxamate; good grades for La, Ce, and Nd, less effective for Nb, Y, and Zr. The data indicated an affinity by salicylic and naphthoyl hydroxamtes for LREE over the HREE minerals. In comparison, benzoyl hydroxamate indicated an affinity for Nb, Y, and Zr. Temperature effects on REE recovery were also studied. The grade and recovery of REEs generated by flotation using a mix of salicylic and benzoyl hydroxamates at room temperature was almost identical or even better relative to the recovery using naphthoyl hydroxamates at elevated temperature.

Jan 1, 2014

By T. Yalcin

"This paper describes the development of a process flowsheet designed to provide high dewatering rates and to bring about savings in tailing disposal costs. The flowsheet comprises a hydrocyclone, a settling cone and a thickener arranged in closed circuit. The mill tailing, after pulp density adjustment, is fed to the hydrocyclone which yields two products. The underflow product is sent to the settling cone for further dewatering. The overflow product, together with the settling cone overflow, goes to the thickener which, with the aid of flocculants, gives a clear effluent and a relatively dilute underflow. The latter combines with the original mill tailing to form the hydrocyclone feed. Solids finally leave the system in the settling cone underflow which can reach pulp densities of up to 78%, making it suitable for direct disposal or for use as mine backfill.Some discussion is included for the selection and sizing of equipment required for this process. INTRODUCTIONDewatering is an essential process for the disposal of mill tailings which forms an added burden in milling practice, often with little or no return. It is, therefore, desirable to conduct this process as economically as possible. One way of reducing costs would be to increase the rate of dewatering so that savings can be made in the size of dewatering unit s which would lead to lower capital and operating expenditures.A common method of dewatering mill tailings is gravity sedimentation which is frequently carried out with the aid of flocculation. In most cases, flocculation greatly enhances the sedimentation process, but only until a pulp density of 50% to 55% is reached in the settled material.Centrifugal sedimentation in hydrocyclones can provide high pulp densities rapidly, but does not result in a clear effluent.This paper outlines a suitable combination of gravity and centrifugal sedimentations that results in an over-all high rate of dewatering. The system developed produces a material of high pulp density while at the same time giving clear effluent."

Jan 1, 1989

By M. E. Coleman, G. Money

Pneumatic Conveying and Process Injection Technologies have been implemented in the metals markets for the last 40 years and have considerably improved the productivity and the performance of many processes. There have been many steps forward in handling technology and this paper seeks to consider those now offered by Clyde Materials Handling who as an established customer-driven solutions provider has turned its attention to supporting the Metals Market. Clyde seeks to utilise its knowledge, expertise and technologies to transform the production processes of its customers, who operate in the ferrous and non-ferrous metals industries.

Jan 1, 2008

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies' bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By Heidi Fauser

The aim of the project was the development of an electroforming process for the production of medical implants out of gold. To prove the applicability of this technology, tympanostomy tubes were chosen as demonstrators. These barbell-shaped tubes are usually produced mechanically; of silicone or, for higher therapeutic demands, of metal ? gilded silver or gilded stainless steel. Gold electroforming of the tubes as an alternative manufacturing process would reduce the expenditures for the mechanical preparation and lower the corrosion susceptibility significantly. To obtain electroformed gold tubes of the desired shape, the following steps are necessary: fabrication of a negative template by drilling holes with countersinks in an insulated aluminium sheet, electroforming process, removal of the aluminium by using a sodiumhydroxide solution. For the optimisation of the shape and surface quality of the tubes respectively the simplification of the manufacturing process, various parameters were tested, e.g. aluminium quality and sheet thickness, type of insulation layer, substrate processing, hydrodynamic conditions, type of electroforming electrolyte, electrodes position, etc. The manufactured tubes were characterised in view of thickness distribution, hardness, surface roughness and purity in comparison to mechanically produced reference tubes. From the results obtained during the project it can be concluded that electroforming processes can be easily adopted for the manufacture of medical implants. The time-consuming electroforming process is by far compensated by the simultaneous production of an arbitrary number of implants.

Oct 1, 2003

By A. Mellek, M. Pischtschan, M. Perrucci

ABB has received an order for one of the most challenging mill drive projects in its history. With one SAG mill and one ball mill to be added at an iron ore mine in Sweden, the customer’s plant managers wanted to have the most efficient solution for driving their mills but had the budget limitations typically faced by the majority of mining companies during periods of market downturn. To find the best balance between cost of acquisition and highest performance throughout the lifetime of the plant, ABB was selected to deploy a synchronized bypass solution, in which only one drive system is used for two different mills in series. However, being one of the first grinding mills in the world with such a solution was not the only challenge the ABB team faced: The inclusion of some mill application functions - e.g., frozen charge protection, automatic positioning and creeping mode - brought the demands on the engineers to another level. With only one frequency converter and one mill application controller available, the configuration logic and interlocks had to be meticulously designed and thoroughly tested to ensure a smooth and safe startup. The solution offers a footprint reduction and more operator flexibility at a reduced investment as each mill can be run in both directions, and wear on the mechanical components can be greatly reduced due to ABB’s premium ring-geared mill drive (RMD). This paper will describe the details of the project, the configuration developed and the tests performed to guarantee correct software functionality. Mill startup is scheduled for January 2016.

Jan 1, 2016

By H. W. King

"Cryogenic engineering is concerned with components and machines which operate for long periods of time at temperatures within a few degrees of absolute zero. The absence of a ductile-brittle transition is thus the prime component of the specification for a suitable low-temperature alloy. The word "" cryo"" means ""frost-forming"" , and this leads to the second component of the alloy specification, which is resistance to corrosion in humid atmospheres. Further, although most early applications of low-temperature alloys were limited to the storage or transportation of liquified gases, an increasing proportion of alternative energy storage and conversion technologies are being based on the availability of high-field superconducting solenoids. The third basic component of the specification for a low-temperature alloy is thus the absence of a low-temperature ferromagnetic transition.Although the firs t two of these components of the specification can be met by using austenitic stainless steels, many of these supposedly "" non-magnetic"" alloys have been found to undergo martensitic transformations to ferromagnetic phases at very low temperatures. In addition, steels which remain structurally stable may still exhibit other magnetic transitions, e.g. to antiferromagnetic or superparamagnetic states. The successful application of these alloys in cryogenic engineering has thus required an initial basic study of the types of magnetic transition that can occur in such concentrated solid solutions, followed by a more applied study directed at an alloy formulation which will induce beneficial magnetic states at low temperatures."

Jan 1, 1981