Search Documents

By K. Dinh

The Ground Penetrating Radar (GPR) has been studied for a long time as a non-destructive evaluation (NDE) technology for inspection of concrete structures. Currently, the most widely used technique for interpreting GPR data of concrete bridge decks is the one that based on the amplitudes measured at various interfaces such as asphalt-concrete, top rebar, or slab bottom. The assumption behind this technique is that a sound concrete deck should have the same reflection amplitude at these interfaces while any low number would indicate some sign of deterioration. Unfortunately, this assumption is not completely valid in most cases. As a consequence, the reported test results usually do not reflect real condition of concrete bridge decks in question. The main goal of this paper is therefore twofold: (1) to discuss the limitations of the amplitude analysis method, and (2) to propose a new model that interprets GPR data of concrete bridge decks. The model methodology is based on the comparison of GPR A-scans between two inspections, using the so-called correlation analysis. The results, indicated by the correlation coefficients, are then employed to develop a contour map that estimates different levels of deterioration. The model is then implemented to a case study in order to illustrate its methodology.

Aug 1, 2013

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Mines Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840 µm to 1200 µm in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding , smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840 µm to 1200 µm class reported to the 600 µm to 840 µm; this figure is much higher than for silica (46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50 urn to JOO pm to 20 at 500 um to 1000µm.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840 µm to 1200 µm to the 600 µm to 840 µm class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photograhic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase over-all gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydro cyclones takes place at a much finer cut-size than ore, 20 µm vs 57 µm. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty-four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3 in.) Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89% and 92% for the PCUF and secondary mill discharge."

Jan 1, 1991

By Gonzalo Mato, Colin Godwin, G. Ditson

"The mid-Cretaceous Seagull batholith intruded Mississippian sedimentary and volcanic rocks and Jurassic(?) granitic and ultramafic rocks within the Omineca Crystalline Belt in the Yuk on Territory near the British Columbia boundary. Leucoerotic fluorine- and boron-rich granites of the batholith exhibit many textural variations from aplite to pegmatite, but are dominated by a coarse-grained seriate unit and a fine-grained porphyritic unit.Four distinctive tin vein occurrences within and near the batholith are described, the most interesting of which is the MC showing of quartz-calcite-chlorite-cassiterite veins in intensely fractured zones of sedimentary and volcanic rocks. Three other showings occur within the batholith:J) the EC showing of quartz-fluorite-cassiterite-sulphide veins with prominent muscovite-illite alteration;2) the DU showing of quartz-hematite-fluorite-sulphide- sulphide-cassiterite with considerable manganese staining and sericitic alteration; and3) the VAL showing of quartz-tourmaline-cassiterite-fluorite-arsenopyrite veins with little associated alteration.Most cassiterite occurrences are within easterly-trending, vertical structures and all occurrences are thought to represent parts of a single system. These mineralogical and physical variations are apparently related to the distance from the upper contact of the batholith.For the Seagull batholith, Rb-Sr isotopic data give a 100±1.4 Ma isochron age that is concordant with the K-Ar model age from biotite of 101±4 Ma. Initial Sr isotopic ratios for the batholith are high at 0.712, indicating an old, sialic crustal source for this pluton. This initial ratio is similar to values for granitic rocks associated with tungsten deposits in the Yukon Territory. The high initial ratio for Sr, the high Si02 content, the high s/I index, the presence of normative corundum. leucogranitic composition and associated lithophile-tungsten mineralization demonstrate that the Seagull batholith is probably an S-type granitic body. This factor is significant to regional exploration jar tin and tungsten in the Canadian Cordillera."

Jan 1, 1983

By G. E. Wood

Steep Rock Resources Inc. owns a calcite quarry property at Tatlock, Ontario, and a calcite processing plant at Perth, Ontario. The Tatlock marble deposit forms part of an extensive series of carbonate rocks of the Grenville Geological Province in the Precambrian Shield of southeastern Ontario. The deposit is very unusual, if not unique, in the Grenville area in its combination of characteristics of large size, whiteness, high calcium content, low magnesium and silica contents, and scarcity of accessory minerals. A major expansion of the fine grind products capacity of the plant was undertaken in 1982 and came on stream in 1983. The expansion provides important operating benefits at the plant: greater flexibility as to the product mix and reduced dependence on the single grinding mill previously in place. The expanded facility consists of prima,y and secondary crushers, a rotary drye,~ a screenhouse producing a range of screen separator grade products, an airswept Raymond Mill, and a pebble mill with integrated air classifiers, product storage bins, bulk, semi-bulk, and bagged product shipping capabilities, road and rail access, and a substantial product warehouse. The expansion was designed to be compatible with a move into ultrafine calcite production, and is capable of supplying the anticipated sales growth within its market area during the next 5 years. Products are exceptionally white, with good chemistry, low abrasion, and consistent quality. Markets range, according to product particle size, from pre-cast concrete aggregate to fillers for coatings, plastic pipe, and compounds.

Jan 1, 1984

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

This growing dependence of Canada upon foreign mineral commodities, just referred to, applies particularly in the direction of the United States. There is, in fact, no more significant feature of Canada's mineral trade than the manner in which it affects the Dominion's commercial standing with that country. Our heavy adverse balance of trade with the United States is perhaps not a matter of such wide concern or frequent comment as was the case two or three years ago. It is, of course, a well-known fact that the Dominion each year buys from the States a volume of goods to a value enormously in excess of our sales to that country. And it has come to be accepted as a ?normal, though not altogether satisfactory, feature of our international commerce that a huge portion of the bill incurred by our American purchases must be met, not by our American sales, but by the proceeds of our sales to other countries, not-ably Great Britain. It is a three-cornered situation in which our trading deficit with the United States is covered largely by our trading surplus with the United Kingdom. In this situation the mineral trade plays a remarkable part. If one delves into the details of our transactions with the United States it will be found that, in one sense, the mineral trade is entirely responsible for the huge annual balance against the Dominion. In fact, Canada gets decidedly better than an even break on Canadian American trade, if one leaves out of account the three mineral groups, "iron and steel", "non- metallic minerals", and "non-ferrous metals".

Jan 1, 1924

By L. C. Kitchener, K. Vollenwyoer

"This paper describes the development of an automated, 70-ton capacity, underground electric trolley truck at Inco Ltd. The purpose of the project is to provide a high capacity and high productivity haulage system to suit continuous loader applications in existing mining horizons where conveyor belt application is not immediately practical. IntroductionWith the start o f a program by Inco in mid-1983 to develop a continuous loader for bulk mining of our hardrock orebodies, the need for a rapid ore transportation system was recognized to match the increased extraction rates planned. Two methods were investigated, truck haulage and conveyor belt. As a result, a conveyor belt system has since been designed and installed with a continuous loader at Stobie Mine and an electric truck has been designed, fabricated and assembled, with shop testing underway. This paper deal s with the latter project. BackgroundMany existing mining horizons which could utilize continuous loaders do not have the straight runs required for conveyor belts. In these situations, truck haulage would be the only alternative of the other transportation methods that would be practical. In order to match the high productivity potential of the continuous loader, however, a more efficient trucking system is required than would be available with conventional diesel powered trucks or with electric truck designs commercially available, or under development. A higher capacity truck and an automated operation is necessary so that the application of additional units to suit increasing haulage distances matches loader output without reducing over-all productivity because of the need for additional operators.A first effort to work with a major electrical manufacturer was unsuccessful and resulted in a project delay of almost one year. In November 1984, an investigation into the concept was reinstigated with UTDC, and an agreement to start design was reached in April 1985."

Jan 1, 1988

By Michel Noël

Cet article présente une compilation partielle des mesures adoptées pour la fermeture des haldes de stériles pour des mines situées au Canada et en Alaska, et dont le climat comporte des hivers froids. L?article présente également le processus de sélection qui a été suivi pour certaines de ces mines. Les exploitations minières produisent habituellement des quantités de stériles qui peuvent être importantes. De plus, la nature du dépôt minier ainsi que la roche mère vont souvent entraîner des impacts sur l'environnement. Ces impacts doivent être gérés non seulement durant les opérations minières, mais souvent à très long terme après la cessation de l?exploitation minière. Les plans de fermeture de mine doivent par conséquent procurer des solutions à très long terme, voire même à perpétuité dans bien des cas. Le processus de sélection implique souvent l'évaluation des risques liés aux responsabilités environnementales et financières. Il doit considérer l?aspect scientifique, comporter une définition des objectifs, tout en incorporant une gestion des ressources et des plans de travail. La planification de fermeture est essentiellement un exercice de prise de décisions comportant des contraintes. Une matrice de classement basée sur la performance et le risque est souvent développée durant ce procédé pour identifier les options préférées. Les études de cas présentées dans cet article présentent quelques exemples. L?état des connaissances sur le drainage acide minier provenant des haldes de stériles a augmenté considérablement au cours des dernières décennies. Ceci n?a pas nécessairement augmenté le niveau de complexité des méthodes adoptées pour la fermeture. Une approche qui est fréquemment utilisée consiste à stabiliser les pentes des haldes de stériles en abaissant la pente des talus pour ensuite recouvrir les stériles d?une couche de sol pour soutenir la végétation. De telles couvertures empêchent les animaux d?avoir un contact direct avec les stériles, minimisent l'érosion et réduisent l'infiltration à divers degrés. L'inclusion d?un traitement des eaux dépend évidemment de la qualité de l'eau au point de déchargement.

Nov 1, 2008

By Gary S. Anderson

Rajant Corporation is the global leader in mining communications systems implemented a vision to develop a wireless network that is rapidly deployed, self-powered and managed, for portable or fixed configurations ? Mobile, Portable, Self-Powered, Secure and High Bandwidth. The network configures itself allowing for very rapid deployment without the time delay and personnel typically required for set-up and configuration. Rajant?s proprietary technology ?InstaMesh®? is incorporated in a device called a BreadCrumb®. Rajant has filed several patent applications on its proprietary technology and has received trademark protection on its brand names. The BreadCrumb® uses technology which allows mining, military and first responders to easily establish internet connections at remote sites or situations where existing internet communications has been disrupted. The BreadCrumb® products are standards-based Wi-Fi 802.11 a/b/g compliant, ruggedized, lightweight, portable; self-meshing and the system can be established by just turning on several of the BreadCrumb® units. The Rajant Network has evolved in the ?One Network? philosophy and has been deployed by both the military and homeland defense organizations. With multiple radios, transmitting on multiple frequencies as the same time, bandwidth is doubled, the speed of the network is enhanced, management is simplified, and manageability is made easier. Rajant has partnered with world class integrators and partners, including ten CAT dealers, a world-wide mining technology company, a mining and construction software company and leading technology innovators in mining automation and operations. Recently, Rajant provided a significant network to Rio Tinto?s Iron Ore of Canada Mine in Labrador City, Newfoundland, Canada, Kennecott Utah Copper Mine, and is currently the wireless standard at Peabody Energy and several mines in Australia. These networks range from 20-250 BreadCrumbs®. The result is a meshed mobile broadband network capable of operating in a vast open pit active mining space. Simultaneous applications currently running on these BreadCrumb® networks in the mining sector consist of Caterpillar?s VIMS?s, CAESultra grade control and Aquila Drill Management Systems, Carlson Grade Control systems, Jigsaw Technologies and Modular Mining fleet management system, Ground Probe Radar, an Automatic Train Operation and various video and VoIP applications. All vendor applications have been turned off and all applications are running on Rajant?s ?One Network?.

May 1, 2010

By M. Pesowski

"Certain environmental problems can substantially alter the physical properties of the subsurface. In such cases, geophysical methods can be used to map the distribution of subsurface contamination or buried wastes prior to drilling or sampling. For example, inorganic contamination by acids, bases, salts, or metallic ions can be detected by instruments that measure ground conductivity; metallic objects such as buried drums, pipelines, etc. can be located by magnetic survey, and radioactive mine waste can be mapped by radiometric techniques. Geophysical methods can also be used to characterize site geology. If carried out prior to development, they can assist in identifying areas of high- and low permeability and sources of natural contamination. The methods can also be used to establish baseline values and to locate stable areas for development of environmentally sensitive facilities. Application of geophysical methods to environmental problems is illustrated with examples from base-metal mines, uranium operations, and potash and oil-sands operations. Particular attention is given to the problem of acid mine drainage. =IntroductionGeophysical methods have been used for many years by the mining industry in exploration and geotechnical investigations. The basic techniques for mapping variations in physical properties of the subsurface have been adapted to meet the special needs of resource exploration and development in the coal, potash , oil sands, industrial minerals, precious metals, and base-metal industries. Now the mining industry is facing another challenge: to operate the mining cycle, from discovery to closure, with minimum impact on the environment. This involves the rehabilitation of abandoned mining sites, the minimization and effective containment of pollutants at operating and developing sites, and the longterm containment and monitoring of sites after mine closures.Some of the most difficult aspects of environmental control and monitoring relate to the location of buried waste and contaminated fluids in the subsurface. As in the search for buried ore deposits or in geotechnical investigations, geophysics can be a valuable aid in subsur face environmental investigations. Investigations can be remedial , involving the location or monitoring of existing problems, or preventative, where problem areas are identified or background values are established before site development. In either case, geophysical methods should not be considered as a substitute for drilling. Geophysical interpretations in general do not provide the detail required for a complete environmental or geotechnical investigation. They are most useful as rapid reconnaissance methods for targeting subsequent drilling or for interpreting subsurface condit ions away from drill holes. Table I lists the common geophysical methods and the physical properties to which they are sensitive."

Jan 1, 1993

By Fridrik J. Kristjansson, Stephen R. Hicock

"Three varieties of till are recognized in the Beardmore-Geraldton area: local lodgement till, nonlocal carbonate till, and local supraglacial till. The local lodgement till unit is examined in detail for the first time in this paper. It is the best potential overburden exploration medium for gold and other metals because its particles were locally-derived and deposited subglacially, probably within a few kilometres downglacier (southwestward) from their sources, and have not been diluted by distantly-derived glacialdebris. Both local tills are richer in gold and other metals, relative to nonlocal carbonate till. Local lodgement till rests on bedrock and was encountered frequently at or near the surface in thin drift/bedrock terrain (a widespread terrain type within the west half of the study area), and commonly at the base of boreholes in thick till terrain.INTRODUCTIONDrift prospecting in areas of glaciated terrain has been well documented (in a variety of journal publications and symposium volumes; e.g . Strobel and Faure 1987; MacDonald and Mills 1988) and has proven valuable especially where overburden thicknesses hinder traditional exploration techniques. Drift prospecting techniques may well prove valuable in the Beardmore Geraldton area. This applies especially to the Wildgoose Lake Turkey Lake area where a thick and laterally extensive sheet of nonlocal carbonate till has impeded conventional mineral exploration programs (Fig. I; note the lack of gold occurrences around Wildgoose Lake).Till in .particular has been cited as the best prospecting medium among the various types of glacial sediment (e.g. Shilts 1984). Three end member till varieties are recognized in the study area: (I) local lodgement till which rests directly on bedrock; (2) non local carbonate till; and (3) local supraglacial till which occurs predominatly within, or just downglacier of, upland areas where it commonly mantles the other till varieties. Previous authors have documented how the non local carbonate till hinders gold exploration (Geddes and Kristjansson 1986; Karrow and Geddes 1987; Kristjansson 1986; Hicock 1986, 1987a, b, 1988; Kristjansson and Thorieifson 1987; Thorleifson and Kristjansson 1987, 1988a, b) and why the local supraglacial till may be a good unit for prospecting (Hicock 1986). One detailed surficial geology map sheet of the area has been published (Kristjansson et al., 1988) and others are in preparation. Closs and Sado (1981) reported on the geochemistry of soils and glacial sediments in the west half of the study area. This paper documents the local lodgement till unit and demonstrates why it is the best overburden unit to use for drift prospecting."

Jan 1, 1989

By Akiyoshi Horiuchi, Manabu Kanno, Shigeki Sato, Taro Aichi

"AKITA ZINC Co., Ltd. (Iijima Zinc Refinery), jointly owned by DOWA METALS & MINING Co., Ltd.(DMM), has used the company’s own hematite process for iron control since the beginning of operations in 1971. The hematite process consists of reductive leaching with SO2 gas and iron removal in autoclaves by high temperature hydrolysis. This process enhances not only zinc recovery but also the recovery of gold, silver, copper, lead and rare metals, which is carried out at another DOWA metallurgical plant. All by-products produced in the hematite process are marketed and sold. This paper presents an overview of the hematite process and the recent process improvements made.INTRODUCTION DMM carries out mining and smelting activities for precious metals, PGMs, rare metals and base metals such as copper, lead and zinc. It owns KOSAKA SMELTING & REFINING, producing copper and lead, and the AKITA ZINC Co., Ltd. (AZC) in Akita Prefecture. DOWA is a specialized smelting company which has established a metallurgical complex for copper, lead and zinc, including a recycling business. AZC was established in 1971 at a production capacity of 72,000 t/y zinc; it is jointly owned by DMM and five other non-ferrous metal companies. AZC has increased its capacity continuously and now produces 210,000 t/y of zinc. Figure 1 shows the changes in zinc production and capacity at AZC."

Jan 1, 2016

By C. V. Sibbald

"This paper provides a description of the Highmont copper-molybdenum concentrator from primary crushing through grinding, flotation, tailings disposal and water reclamation. The unique features of the operation will be emphasized.IntroductionThe Highmont property is located in the southern portion of the Highland Valley adjacent to and east of Lornex and about 4 miles south of Bethlehem Copper. The plantsite is at an elevation of 5100 ft.Highmont acquired the property in 1966 and in 1969 Teck Corporation entered into an exploration agreement which contained the option to finance the property to production . A detailed feasibility study of the project was completed in 1971. A positive production decision was deferred at that time because of the prevailing soft copper market and relatively low molybdenum price. The development of a strong molybdenum market in late 1978 and early 1979 led to a re-examination of project economics, and a decision to proceed to production was made in April 1979.The Highmont ore zones occur adjacent to and on either side of an east-west-trending quartz porphyry dyke. The two major zones , the east and west pits, contain 122 million tons of ore assaying 0.27070 Cu and 0.029% Mo. Chalcopyrite, bornite and molybdenite are the minerals of economic interest. Chalcopyrite is the predominant copper mineral. Mineralization occurs primarily along fractures and is zoned according to fracture density. Some pyrite is present, but for the most part it is outside the ore zone. Surface oxidation is shallow throughout the orebody.Wright Engineers Limited were responsible for the major part of the engineering design. Site construction, which began in the spring of 1979, is under the direction of Commonwealth Construction. The first concentrator line is scheduled for completion late in 1980, the other for early in 1981."

Jan 1, 1981

By Frank Mucciardi, Louca Gourtsoyannis

"Low and inconsistent recoveries of aluminum in the production of aluminum-killed steels triggered an extensive research program on the aluminum dissolution kinetics at McGill University. This research program led to the understanding of the melting kinetics and the hydrodynamics of making additions to liquid steel. It showed the necessity of gradually releasing liquid aluminum at the bottom of the ladle to increase aluminum recoveries.This knowledge was verified in practice at Sidbec-Dosco, where a prototype aluminum wire injector was developed and installed for the first time in Canada. The industrial application showed the validity of the theoretical and experimental results and provided further data for the mathematical modelling of the process.The development of the theoretical understanding, the industrial results, and the interaction between university and industry are presented.IntroductionAluminum is an extremely effective deoxidizer of molten steel; nevertheless, an efficient method of adding it to steel has eluded steelmakers for many years. It is well known that the recovery of aluminum used in the production of aluminum killed steel is both low and eratic, especially when the aluminum is added in the form of bars or lumps from chutes into filling ladles, a practice still common in many of today's steelmaking operations.As the density of aluminum is only about 40010 that of molten steel, it is conceivable that loose bars of aluminum simply ""thrown"" into a filling ladle will resurface before any appreciable dissolution of the aluminum has occurred, particularly if the depth of penetration of the additions is small. Before one can conclude that this is indeed the case, it is necessary to know the melting kinetics of an aluminum addition. Back in 1972, this information was not available; hence an extensive research program which focused on melting kinetics was initiated at McGill University."

Jan 1, 1982

By T. Gerritsen, T. Plikas, K. Ochoa, M. Loveless, R. MacRosty, J. Reichart, R. Pula

Sidewall accretion in a smelting furnace plays an important role in furnace integrity as it provides protection to the sidewall cooling elements and thereby extends the furnace campaign life. The extreme thermal and mechanical stresses in the furnace and changes in the slag chemistry can cause the sidewall accretion to melt or break away decreasing the lining protecting the cooling elements. Thin accretion is highly undesirable as it increases the risk of exposing the cooling elements to the molten bath and in the worst case may lead to a failure. Therefore, monitoring the sidewall accretion on an operating furnace is extremely important to manage furnace integrity and to support safe furnace operation. Operators often generate estimates for sidewall accretion and refractory thickness using either copper cooler temperatures or heat load into the cooling water circuits. Multivariate statistical models, on the other hand, have the capability to consider all the process measurements simultaneously to provide a more reliable estimate. This paper describes the application of multivariate statistical models for sidewall integrity monitoring on a Flash Converting Furnace (FCF) and also discusses the online implementation of these models as the Sidewall Accretion Monitoring System. INTRODUCTION Rio Tinto’s Kennecott Utah Copper (KUC) smelter located near Salt Lake city, Utah operates a Flash Smelting Furnace (FSF) and a Flash Converting Furnace (FCF) to produce high-grade matte and blister copper respectively. Since the commissioning of smelter in 1995, several improvements were made to these furnaces to increase their efficiency and operational safety. At present, Kennecott smelter is known to be among the lowest-emission and highest energy recovery copper smelters in the world. Since the smelter start-up, Kennecott has invested in several advanced furnace monitoring practices to evaluate the integrity of the furnaces and improve their campaign life. An example is their temperature monitoring system installed for the smelting and converting furnaces, which continuously monitors the furnace sidewall temperatures and notifies the operators during temperature excursions. During an investigation on the converting furnace, it was revealed that there were frequent temperature excursions in the settler sidewall area towards the reaction shaft end of the furnace that caused significant furnace downtime. The reason for the sidewall temperature excursions was not clearly known.

Jan 1, 2019

By J. Donnelly, A. V. Deev

Substitution of coal and coke by renewable carbon (charcoal) is a low-risk and low-capital path to 50% or more reduction in net CO2 emissions by the steel industry. However, the high cost of charcoal and its low availability in most countries are barriers for the implementation of this approach. Development of an efficient wood carbonisation technology (slow pyrolysis) capable of producing large-volumes of charcoal from low-cost wood feed (e.g. wood wastes or forest residues) is an essential step towards the use of renewable carbon by the iron and steel industry. This paper provides a summary of the progress made over several years of R&D covering: (1) development and piloting of a new energy efficient slow pyrolysis process for production of charcoal from woody biomass at a competitive cost to the PCI coal, (2) techno-economic evaluation of the process. The main feature of the process is that the material undergoing pyrolysis is heated spontaneously without the supply of heat or air to the reactor. This makes it possible to carbonize large volumes of small-sized wood (e.g. wastes and residues) in a single reactor unit and capture high calorific value pyrolysis by-products

Jan 1, 2015

By Helen Morrison, Chris Staun, James Vaughan

"Mercury is introduced into the Bayer refining process as a trace element in bauxite. During the digestion stage, a portion of the mercury is extracted which partitions between the flash tank off-gas, vapour condensate and bauxite residue streams. A technology or treatment that stabilises mercury in the solid phase during digestion would prevent environmental management issues that may arise from the presence of mercury in condensate and non-condensable gases. This study examines the effect of process additives on the deportment of mercury under Bayer digestion conditions. Bauxite digestion experiments were conducted in batch autoclaves in the presence of additives. Process liquor was analysed for mercury content using a thermal desorption technique. Pyrite and copper hydroxide were evaluated for their suitability as additives.INTRODUCTIONMercury is an ancient metal characterised by electrochemical nobility, volatility, low solubility in water and a liquid state at room temperature (Holleman and Wiberg, 2001). The biogeochemical cycle of mercury is complex. Elemental mercury may enter the atmosphere due its volatility, where it can be transported long distances. After settling and adsorption to sediments, methylation is catalysed through microbial metabolism (Qureshi et al., 2009). Methylated mercury species are potent neurotoxins, and bioaccumulation of mercury is well documented, particularly in seafood (Kozin et al., 2013, Pan et al., 2014, Pollman, 2014). Environmental regulations for mercury emissions are becoming increasingly stringent (UNEP, 2015). Considerable research has already been performed and technologies developed for the remediation of mercury in wastewater and the trapping of mercury from industrial stack emissions. Wastewater technologies usually target ionised mercury using adsorbent, ion exchange and complexation mechanisms (Krishnan and Anirudhan, 2002, Li et al., 2015a, Chiarle et al., 2000), while stack emission technology is dominated by impregnated activated carbon adsorbents (Gao et al., 2013, Zheng et al., 2012). Related developments include piezoelectric amalgamating sensors for in line detection of gaseous elemental mercury in industrial stack emissions (Kabir et al., 2015, Sabri et al., 2011). There is a paucity of research regarding removal of mercury from the Bayer process."

Jan 1, 2016

By P. L. Claessens, S. Belisle, C. Bowen

"Use of zinc shot feed is a well-established procedure among North American electro-galvanizers. This form of zinc is easy to handle and relatively inexpensive when compared with zinc oxide. This paper reports results on the kinetics of zinc shot dissolution in traditional pure zinc solutions and in electrolytes used for the plating of nickel/zinc alloys. Despite the cementation of minor amounts of nickel in the latter solution, acceptable dissolution rates of the zinc shot can be achieved through proper adjustment of the solution velocity. Under these conditions, the nickel shell produced by cementation is continuously abraded, exposing the underlying zinc.IntroductionThe use of insoluble, noble metal-containing anodes rather than soluble zinc anodes for the operation of high current density electro-galvanizing lines has gained almost universal acceptance. Two major reasons for this trend are:• improved control of the process by virtue of constant inter-electrode distance; and• increased productivity because the operation of the lines does not require the relatively frequent interruptions for replacement of consumed anodes .The results of the principal anode and cathode reactions are, respectively, depletion of the zinc content of the electrolyte and the increase on its acidity;"

Jan 1, 1991

By Mark B. Thorpe

Golden Star Resources started gold mining operations in Africa in 1999 after 15 years of exploration in South America. At the time, the approach to local assistance was through "alternative livelihood" programs and the donation of infrastructure to local communities. This was initially successful with local community support. However, with time and on reviewing the implemented projects, it became evident that the success was limited and many if the projects were either poorly used or in disrepair. Through a review of the options, we decided to develop a community assistance model driven by the communities themselves, while keeping control of the finances and the actual construction of the projects. Through the formation of the Golden Star Development Foundation, we began to support community driven projects for local economic development. The evolution of economic development projects continued over the next several years with the addition of project requirements for partnerships with government, and finally an evolution to a partnered turn-key piece of infrastructure that we hand over to an agency for operation and ongoing maintenance. We are currently working with outside partners to further our economic development activities in Ghana to the benefit of our stakeholders.

May 1, 2011

By Balmer Neilly

FOR some reason or other, Mine Taxation has never been a popular subject for discussion in meetings of this kind, and it has never received the study and consideration its importance demanded. By way of explanation, two reasons may be suggested. In the first place, the computation, adjustment, and final payment of taxes, have been looked upon in most cases as a Head Office chore. Secondly, since taxes represent an uncontrollable cost item, they have been treated as an added rather than an inclusive factor in calculating unit costs. Perhaps because I am half Irish, and therefore resent taxation of all kinds, perhaps because I am half Scotch, and am therefore concerned with the results, I have always taken a keen interest in this subject. Moreover, by some peculiar set of circumstances, I have been a participating party in many, perhaps I can say most, of the discussions on this subject that have taken place between the Governments and the representatives of this industry during the past thirty years. Looking backward, certain very definite impressions remain. Political considerations have never had any part in these discussions. Views have been exchanged upon the frankest possible basis, and, when we disagreed on some particular detail, we agreed to disagree, and followed through in harmony and? good faith. We, as an industry, have refrained from importuning and fault finding in ways that might be considered as petty or selfish, and it is only upon occasions such as this, where conditions necessitate action, that we lay our troubles before the powers that be. The Ontario Mining Tax Act was drafted by men who were earnest and practical as to purpose, and that Act has stood the test of time. It is, in. truth, a mode! Act, for it has been copied in its general clauses by both Quebec and the Dominion of Canada. We all know that, when a machine is running smoothly, we should leave it alone. The same is true of a well designed, easily applicable, taxation measure, and our present difficulty with respect to this Act arises out of an amendment made in 1916. In that year, you will remember, the Dominion imposed a wartime Income Tax Act. It was described as a wartime necessity and it was intimated t:1 at with the end of hostilities its application would be restricted and finally cancelled. The rate of taxation was modest, and when the Ontario Government was asked that the Dominion Income Tax be allowed as a deductible item, they readily acquiesced. This was looked upon as a temporary arrangement.

Jan 1, 1943