Search Documents

By J M. Anderson

The cable belt conveyor installation at Craigmont Mines Limited, Merritt, B.C., has the greatest one-stage vertical fall of any conveyor installed overland in Canada. Since the late summer of 1961, this conveyor has carried more than 5,000,000 tons of copper ore from open pit to concentrator site. When the conveyor is loaded, the drive motor acts as an induction generator, delivering power to an external circuit. This paper covers the selection, the operation, the performance statistics, and the installation and operating costs of this conveyor system. Introduction T HE Craigmont mine is located in the south-western interior region of the Province of British Columbia, approximately 240 miles northeast of Vancouver. A moderate climate, good roads, service by the Canadian Pacific Railroad, power from the British Columbia Hydro Authority, gas from the nearby main line of the Inland Natural Gas Company and close proximity to the village of Merritt provide a favourable location for this mining operation. The ore occurrences at Craigmont have a vertical extent of 1,500 feet,

Jan 1, 1965

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By P. Fossi

This report describes a pilot-scale study of a hydrometallurgical process to treat high-grade nickel matte or a nickel-cobalt sulphide precipitate to produce high-purity electrolytic nickel. The first step of the process is the oxidative leaching of the nickel-bearing material by nitric acid; the nitrous gases generated during leaching are reconverted to nitric acid. The crude nickel sulphate nitrate solution is purified and is then subjected to a denitrification step. Nitrate separation is effected either by the crystallization of nickel sulphate or by precipitation of basic nickel carbonate. The electrolyte is prepared from the nitrate-free material and nickel is then recovered by electrolysis of the sulphate solution using insoluble anodes. Some technical and economic problems encountered with this processing route are discussed and the method is compared to the "all-chloride" process developed by Société Le Nickel.

Jan 1, 1977

By A. J. Williams

"IntroductionAN EXCELLENT paper entitled Potash Discoveries in Western Canada (l) was presented to the 1948 Annual Meeting of the C.l.M. by L. Heber Cole, of the Department of Mines and Resources, Ottawa. In the intervening three and a half years, the search for oil and gas in Saskatchewan has added considerably to the information available on the occurrence of potash. It is the purpose of this paper to summarize the additional data. For greater clarity, it may be useful, first, to recapitulate some of the highlights of Mr. Cole's paper.Underlying the western plains of Canada there is a large deposit of sodium chloride, believed to be of early Devonian age. Associated with the sodium chloride are certain potash salts, primarily 'sylvinite,' a mechanical mixture of sodium chloride (halite) and potassium chloride (sylvite) crystals. The potash salts, when present, are usually near the top of the salt formation, though in at least one well they were found near the central part of the deposit. Cole reported on some seven wells in Saskatchewan which had encountered appreciable amounts of potash; these were the Ogema, Radville, Davidson Nos. 1 and 2, Prairie Salt Nos. 1 and 2, and Verbata wells. Depth of potash from surface ranged from 7,653 feet in the Radville well to a minimum of 3,466 feet in the Verbata well. Such depths do not compare favourably with those at which the potash is found in mines in the United States, France, and Germany, where about 1,000 feet is the average. The greatest concentration of sylvite encountered was in the Verbata well, where a bed 11 feet thick carried the equivalent of 21.64 per cent K20."

Jan 1, 1952

By W J. Dyck

Past attempts to establish an integrated steel industry on the West Coast of Canada have been unsuccessful for at least three reasons: (a) insufficient reserves of a suit-able iron ore supply; (b) a relatively small local market for iron and steel; and (c) the non-availability of an economical process to produce primary iron on a small scale. Today, the reserves of economically mineable ore deposits are ample to support a steel production of 100,000 to 200,-000 tons per annum. The local market has increased so as to be able to absorb most of this capacity. With-in the next few years, a small integrated steel plant, including the "H-Iron" direct iron ore reduction process for electric furnace charge stock production, will be able to show a profitable operation. Introduction

Jan 1, 1963

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By Carrasco .. P. J. A., R. Parada, I. Saavedra, F. Parada, R. Parra, E. Balladares

In most of the smelters, the management of flue dust has a double objective: the control of minor elements in the anodes and the management of volatiles compounds that can cause contamination due to fugitive gas emissions. This is a special concern when high content of Va elements (As, Sb & Bi) are present in concentrates. We present the results of the experimental study to prove the principle of a novel process that recovers, via volatilization, the As, Sb and Bi in the flue dust as gaseous sulfides, due to a previous sulfidization. In the case of as control any further classical treatment for its stabilization is possible from the gas. The clean calcine can be returned to the smelter avoiding any concentration of these minor elements in the circuit. This process is now tested at pilot scale and shows better indices on carbon footprint than the classical hydrometallurgical process for flue dust.

Jan 1, 2011

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By F. A. Forward

Introduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By M. Zavvari

Flotation, as with most engineering disciplines, involves testwork. Commonly this means going from lab scale to pilot scale to industrial scale. It is important to conduct tests to identify key parameters and to optimize even at the lab scale. To reduce the number of tests while maximizing the information, it is necessary to use Design of Experiment and Statistical Analysis. In this communication Fractional Factorial Design was used to identify the effect of 7 main factors on barite flotation recovery from jig gravity tailings at the Dorrin Kashan operation. The factors include: pH, collector and depressant dosage, impeller speed (RPM), pulp dilution, particle size and flotation time. By analysis of the output with Minitab software all factors were shown to have an effect. Among the factors, pH and flotation time have an interaction effect but the others have wise effect as an interaction effect and main effect. Finally, reliability tests at pH= 9, RPM= 1000, collector 1 000g/ton, depressant l 750g/ton, particle size 90 µm, flotation time 90 s, pulp dilution 23 % solids, the optimum level of each factor, were done. At the optimum level a barite concentrate with average specific gravity 4.308 g/cm3, average grade 93.72% and average recovery 90.04% was produced from the jig tail.

Jan 1, 2009

By R. P. Nicholson

On September 3rd, 1947, the Acadia Coal Company put into operation a central coal preparation plant. This plant was designed to process all coals mined by this Company in the Pictou County coal field. The problem, briefly, was to make a three-way separation of the raw coal fed into the plant. It was desired to remove all stone, metal, and wood from the marketable coal and to produce a splint coal from the raw material which would be suitable for making power. This splint coal product is belted directly to the power plant which is adjacent to the wash plant. To attain this object it was therefore necessary, first, to wash the raw coal, removing all splint, stone, metal, and wood. The stone, metal, wood, and highest-ash splint had then to be removed by a second washing in order to obtain the lower-ash splint for use in the power plant. The plant is on the east side of the Allan colliery, in the town of Stellarton (see accompanying photograph). It is of steel frame construction with wood siding, covered on the exterior with corrugated galvanized iron. Considerable concrete had to be poured for the foundation piers as the plant site is largely 'fill' ground. This necessitated the construction of extremely heavy footings containing a large amount of reinforcing steel. In all, 884 cu. yds. of concrete were poured for the various pits, tanks, and foundations; its average test was about 3,500 lb. per square inch. At the time the plant was constructed, the steel shortage in Canada and the United States was acute and, in order to obtain steel for the structure which is four stories high- an unused part of the Allan bankhead was torn down. Enough steel was obtained from this demolition to fabricate the new plant.

Jan 1, 1948

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By S. H. Schulz

100 YEARS AGO, on the first of August, 1877, the mining engineer Friedrich Koepe was granted the patent rights for a hoist driving ropes on the principle of friction. It was named after him: the Koepe hoist. On the occasion of this centenary, the main features of the Kcepe principle are described.

Jan 1, 1977

By S. S. Teal, W. W. Weber

"AS THE TITLE implies, this paper will deal with the unusual rather than the standard practices as employed . at the property of North Rankin Nickel Mines, Limited. Fortunately •the mining, with the exception of permafrost conditions, and the milling practices, are the normal approaches dictated by the size, type, and character of the orebody. The unusual aspects are linked directly or indirectly to the isolated location and are •principally ancillary requirements or services covering a broad range from climate to supplies and from finance to entertainment. It is our intent to cover the more salient points of interest together with a brief description of the general operation.To understand the primary motivation of the mine, it must be made clear that North Rankin was conceived as a foothold in the Canadian North, that region embracing 40 per cent of the Dominion which ex-tends north of the commercial tree-line and which includes nearly 50 per cent of the Precambrian Shield, our mainstay of Canadian mining. Secondly, this project was born in an atmosphere of premium sales in the nickel markets, assuring a rapid pay-back of the heavy •capital expenditures. And finally, it has •been coddled through the stark reality of a competitive metal market with the hope and trust that the experiences and achievements will lead over the bill to a bigger and better mine in this virgin territory. This is the briefest story of the mine's history, but it pays tribute to the many people who, in thirty years since .discovery, have championed this project."

Jan 1, 1959

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By Edgar Dernedde

Cryolitic melts at a temperature of about 960 °C are used in reduction cells to dissolve alumina and to produce primary aluminium. At these temperatures cryolitic melts with an acidic composition have a significant vapour pressure, which contributes substantially to the evolution of fluorides from these cells, The Antoine equation is commonly used for relating vapour pressure data of liquids at different temperatures, It is also applicable to cryolitic melts, Published equations have at least 20 numerical constants, in order to allow for the effects of melt composition. In the present work a simplified equation with only 12 numerical constants was developed and is applicable for multiple additions to molten cryolite up to 30 wt %, The simplified equation was compared with the published equations of Haupin & Kvande and Gustaysen & Ostvold using 472 vapour pressure data of cryolitic melts. Results showed that the simplified equation has the same accuracy as the published equations in the composition range of interest to industry.

Jan 1, 2004

By Claude Hubert, Robert Sansfaçon

"The Malartic gold camp includes the Malartic Gold Fields, Barnat, East-Malartic, Canadian Malartic and Sladen mines. From 1935 to 1984, these mines have yielded 212 403 kg of gold. They occur within a 900 m wide belt of highly sheared, dislocated and faulted volcanic and sedimentary rocks (Piché and part of the Pontiac groups) herein named the Malartic Tectonic Znne (MTZ). The zone trends WNW-ESE and separates two lithotectonic sedimentary domains, the Cadillac to the north and the Pontiac to the south. The sedimentary domains are characterized by their coherent fold generations consisting of open to tight reclined and recumbent F1 folds that have been refolded into series of asymmetric upright F2 folds. A flat-lying schistosity (S1 ) and a vertical pressure-solution cleavage (S2) are ubiquitous throughout. Discrete sets of brittle and brittleductile faults are synchronous and parallel to each of these two fabrics.The MTZ trends N320° in the northwestern sector of the town of Malartie, changing to N2800 at its easternmost extremity. The Malartie and Sladen faults constitute its northern and southern boundaries respectively. These two faults also bound another set of faults oriented N305°. Throughout the MTZ, the faults at N280° and N320° and those at N305° outline a series of anastomosed motifs that constitute the principal structural feature of the Malartic district. Locally, a fourth set of minor faults at N065° combines with the other three prominent sets. All these faults have disrupted the gold-bearing volcanic, sedimentary and intrusive rocks encountered throughout the MTZ.The MTZ comprises numerous lozenge-shaped blocks of komatiites and basalts or greywackes and black shales which are cut by disjointed dikes, sills and small intrusions of felsic and mafic rocks. The latter includes gabbro, diorite, lamprophyre, monzonite and pegmatite. They frequently fill conjugate sets of fractures. In some areas, they are clustered into coalescent intrusions. The present morphology of these intrusive bodies( cube, chocolate-tablet boudin, parallel epiped and cigar) is not representative of their primary forms but the result of late shearing and faulting indicative of a major tectonic event subsequent to their emplacement. The intrusions were injected during a brittle stage of deformation related to the F1 folding but prior to the development of the F2 folds and subsequent tearing and shearing by late brittle and brittle-ductile faults . The ultramafic and mafic rocks are intensely altered to serpentine, tremolite, actinolite, carbonate, biotite, hematite and pyrite according to the nature of their proto/it h. In the vicinity of the MTZ, all lithologies exhibit mineral assemblages indicative of the upper greenschist or lower amphibolite facies of metamorphism.The structural evolution of the MTZ involved superimposed folding, shearing, transposition, mylonitization, brittle and brittle-ductile faulting. Each lenticular motif results from the combined effect of conjugate sets of shear zones that outline lozenge-shaped blocks where strain markers indicate different strain states from cores to margins. Bedding in ultramafic flows and/or sedimentary rocks is either NW-SE or NE-SW within the blocks but, in the vicinity of the Malartie and S laden faults, it has been rotated to become subparallel to the faults.Ore shoots are most commonly associated with altered and deformed bodies of diorite and monzonite, or some mafic and ultramafic schists and, at the Canadian Malartic, Sladen and East Malartic mines, with metasedimentary rocks. The shoots occur in close proximity to the various faults of the MTZ but the gold itself is intimately associated with pyrite, biotite and carbonate in halos bordering fractures crisscrossing the different host rocks. The density of fractures and the width of their altered zones have been significant parameters in the production of economic ore shoots. Grains of gold are visible in some veins of quartz a"

Jan 1, 1990

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019

By A. Ghahremaninezhad, E. Jorjani, A. Riahi, Islamic Azad University, B. Nazari, H. Hani, Z. Manafi

The presence of a high iron concentration, 9.1 g/L, in the raffinate of the Sarcheshmeh copper heap bioleach process led to the formation of various types of jarosite, (K,Na,NH4,H3O)Fe3(SO4)2(OH)6, on the heap mineral surfaces. This study probes iron removal from the raffinate using a bio-oxidation process based on A. ferrooxidans bacteria in the presence and absence of jarosite seed. The jarosite seed was biologically synthesized using A. ferrooxidans bacteria. The effect of solution pH (1.5 to 2.5) and jarosite seed dosage (0 to 15 wt.%) on iron removal was examined. It was demonstrated that the concentration of iron ions present in the raffinate decreased from 9.1 g/L to 2.5 g/L with the addition of 10 wt.% jarosite seed at pH 2 and 130 rpm mixing rate at 32°C. Three different types of raffinate including (1) native raffinate containing 9.1, 3.4, 5.7 g/L of total, ferric and ferrous iron, respectively, (2) bio-oxidized raffinate in the absence of the jarosite seed containing 8.5 g/L total iron (mainly ferric with negligible ferrous), (3) bio-oxidized raffinate in the presence of jarosite seed containing 2.55 g/L total iron (mainly ferric with negligible ferrous) were used in mesophilic, moderate thermophilic and thermophilic bioleaching processes. The results of the flask tests showed that the highest copper bioleaching recoveries of 9.4, 49.4 and 90.8 % were achieved using raffinate (3) with mesophilic, moderate thermophilic and thermophilic bioleaching processes, respectively.

Jan 1, 2016