Search Documents

By James H. Courtright, Kenyon Richard

SILVER Bell is situated 35 airline miles northwest of Tucson, Ariz., in a small, rugged range rising above the extensive alluvial plains of this desert region. Its geographical relation to other porphyry copper deposits of the Southwest is shown on the inset map in the lower left corner of Fig. 1. The climate is semi-arid. Altitudes range within 2000 and 4000 ft. Opening of the Boot mine, later known as the Mammoth, in 1865 was the first event of note in the district's history. Oxidized copper ores containing minor silver-lead values were mined from replacement deposits in garnetized limestone and treated in local smelters. Copper production had approached 45 million pounds by 1909 when the disseminated copper possibilities in igneous rocks were recognized. Extensive churn drill exploration carried out during the next three years resulted in partial delineation of two copper sulphide deposits, the Oxide and El Tiro. Although the then submarginal tenor discouraged exploitation of these disseminated deposits, selective mining of orebodies in the sedimentary rocks continued intermittently until 1930, providing a production total of about 100 million pounds of copper. The American Smelting & Refining Co. began exploratory and check drilling in 1948 and subsequently made plans for mining and milling the Oxide and El Tiro orebodies at the rate of 7500 tons per day. Production began in 1954 at a rate of about 18,000 tons of copper annually. Formations ranging in age from Pre-Cambrian to Recent are exposed in the Silver Bell vicinity. The more erosion-resistant of these, Paleozoic limestone and Tertiary volcanics, predominate in the scattered peaks and ridges comprising the Silver Bell mountains. The porphyry copper deposits are located along the southwest flank of these mountains in hydrothermally altered igneous rocks. These are principally intrusives which cut Cretaceous and older sediments and are considered to be components of the Laramide Revolution. For three-fourths of its length the zone of alteration strikes west-northwest, Fig. 1. There now is no single structure that accounts for this alignment. However, indirect evidence suggests that a fault representing a line of profound structural weakness existed in this position prior to the advent of Laramide intrusive activity. This line will be referred to as the major structure. It was obliterated by the Laramide intrusive bodies but exerted a degree of control on their emplacement, as evidenced by their shapes and positions. The influence of fault structures on the shapes of intrusives in other porphyry copper districts has been noted by Butler and Wilson' and by others. As shown on the inset map on Fig. 2, a fault of parallel trend and considerable displacement lies to the north. This fault is now marked by a line of small Laramide intrusive bodies. To the south is a third fault of large displacement. Evidence of its age in relation to the Laramide intrusions and mineralization is not recognized, but its conformance in strike with the other two major faults is significant. These three breaks establish a pronounced trend of regional faulting. They are high-angle, and the southerly one may be reverse, Stratigraphic separations on these faults are of the order of several thousand feet. The local Paleozoic section is about 4000 ft thick. It is composed predominantly of limestone with a basal quartzite member. The Cretaceous section appears to exceed 5000 ft. Conglomerates, red shales, and arkosic sandstones (the youngest) characterize the three principal members. Intrusion of alaskite marked the beginning of Laramide igneous activity. It was emplaced as an elongate stock with one side closely conforming to the major structure line throughout a distance of nearly 4 miles. The alaskite was at one time regarded as a thrust block of pre-Cambrian rock'; however, its intrusive relationship and consequent post-Paleozoic age has been established by inclusions of limestone found in outcrops north of El Tiro. The next event was the intrusion of a large stock of dacite porphyry into Paleozoic sediments and alaskite. The stock was some 3 miles wide and at least 6 miles long in a northwesterly direction. It was sharply confined along its southwest side by the major structure line. A number of large pendants of moderately folded Paleozoic sediments occur within and along its southwest edge. Thus the inferred, original major fault between Paleozoic and Cretaceous sediments became a contact between alaskite and Paleozoic sediments and then a contact between dacite porphyry and alaskite. Andesite porphyry may have been intruded later than the dacite porphyry, but relationships are not clear; it may be simply a facies of the latter. The intrusive activity was at this stage interrupted by an interval of erosion. The erosion surface probably was rugged, as there were local accumulations of coarse, angular conglomerate. Subsequently a series of volcanic flows and pyroclastics several thousand feet thick was deposited. A similar unconformity has been recognized elsewhere in the Southwest, particularly in the Patagonia Mountains near the Flux mine some 75 miles southeasterly. Here, as at Silver Bell, volcanics were deposited on an erosion surface cut in Cretaceous and older sediments which had been intruded by alaskite. Though no evidence is offered that closely defines the age of this unconformity, and proper analysis of the problem is beyond the scope of this paper, it is

Jan 1, 1955

By W. J. Slatosky

W. 0. Philbrook (Cairiegie Institute of Technologyogv—Mr. Slatosky has presented an interesting and constructive paper that represents another step along the way of converting steelmaking from an art to a science. I am confident that his computer will be practical and successful and that with a very few months of experience it will provide a significantly better degree of control than his record of 65 pct of heats within range obtained with the slide-rule calculator . A paper such as this, with a lot of symbols and condensed mathematics, is difficult to comprehend quickly. Since I have had an opportunity to study it carefully, perhaps my evaluation of its validity and accomplishments will save time for others. Mr. Slatosky has correctly used standard principles of stoichiometry and heat balances, which are available to anybody, but he has also brought to them two original contributions: 1) He has developed from operating data some empirical relations for predicting the final FeO content of the slag (at 0.5 pct C end-point) as a function of slag basicity, lance height, and scrap, ore, and scale in the charge. This improves the accuracy of prediction of temperature or scrap requirement compared with assuming an arbitrary, constant FeO content at the end of each heat. There is no assurance yet that exactly the same relations will hold for other furnaces or practices, but similar correlations can be expected. 2) He has combined calculations that are ordinarily carried out laboriously as a number of individual steps into a single, simple linear equation that can readily be fed into a machine. This involved a tremendous amount of painstaking detail work as well as the imagination to see the possibility and work out the steps. While his particular Eqs. [3] and [6] are valid only for the furnace design, charge weight, and blowing time used at Aliquippa Works, only a few numerical values have to be changed to adapt it for other conditions. In order to arrive at a useable solution, Mr. Slatosky had to make some basic assumptions about the process that are similar to those used by others. He neglected variation in some process variables and assumed an arbitrary average value for waste gas analysis and temperature for want of more exact information at the present time. All of these judgments are clearly stated. In addition, some thermody-namic data presently available are not adequate for the job, notably in relation to heats of formation and sensible heat in slag, and some expedient has to be adopted to get around the difficulty. Other people might prefer slightly different judgments about these details and hence obtain somewhat different numerical solutions. This is not of serious importance, however, because the errors accumulate in the "heat loss" term and are largely self-compensating for a constant heat time. Although the extended Eq. l(a) in Appendix I was set up as a rate equation originally, for convenience in using an analogue computer as stated in the paper, the time dependence was removed by later mathematical manipulations and assumptions about the process. The final result is an integration of element and energy balances from initial to final states; this procedure is as legitimate here as in any other form of heat-balance calculation. The formal handling of stoichiometry and thermochemistry appears to be correct, and it is assumed that any arithmetical errors would have come to light in applying the calculations to furnace practice. Mr. Slatosky's approach is not necessarily unique, in that other people might start with apparently different equations or prefer another form of final equation for another type of computer. However, he has presented an accomplished result that appears to be a theoretically sound and practically useful way of applying scientific principles and rapid computation for better control of steelmaking. His success will undoubtedly encourage himself and others to improve on the mathematical model and its use as better informatioq becomes available. John F. Elliott (Massachusetts Institute of Teck-t2ology)-The last comment by Mr. Richards that a calculator is quite unnecessary for an L-D operation ?-equi??es a rebuttal. The L-D furnace is a very high capacity process which places a premium on close control. When one is making steel at rates between 100 and 200 tons per hr, one cannot afford the luxury of an extra 5 or 10 min at the end of a heat correcting for an error that should never have been made in the first place. Mr. Slatosky's paper is a very sound application of the simple principles of stoichiometry and the energy balance. It is a satisfactory and valuable start, but only the start of the development of methods of control for this process. An analysis of the process shows that it should be very suitable to control by a computer. This is especially the case when various grades of steel are to be made. In fact, it would seem that the organizations who are planning new and bigger installations of L-D vessels should consider carefully the advantages that would stem from computer control of a vessel with the operator present to do little more

Jan 1, 1962

By C. Kolm, E. P. Warekois, S. A. Kulin

MUCH insight has been gained into the nature of the cold-worked state of metals in recent years through the use of modern X-ray techniques. These methods have revealed the existence of stacking faults together with regions of high internal strain and have provided means of measuring the atomic perturbations in plastically deformed metals. In view of the recent increased interest in the solid state, it is desirable to extend these techniques to the study of lattice imperfections introduced into semiconductors during plastic deformation. It is of particular interest to compare the state of imperfection sustained by metallic bonding with that sustained by the covalent bonding found in semiconductors. A knowledge of the imperfections which can exist in semiconductors is important from both a theoretical and a practical point of view since they can greatly influence many of the physical properties. In order to determine the possible existence of stacking faults in covalently bonded structures, precise measurements were made of the diffracted peak positions of plastically deformed germanium, gallium antimonide, and indium antimonide. These measurements were based on the theoretical treatment of Paterson1 and are similar to those employed by Warren and warekois2 in their studies of deformed a brass. In addition, diffraction peak profiles were measured on the annealed and plastically deformed materials in order to obtain information concerning the distribution of internal strains through the use of the Fourier methods developed by Warren and Averbach.3 EXPERIMENTAL PROCEDURES AND TECHNIQUES Because of the room-temperature brittleness of the semiconductors studied, it was necessary to plastically deform the materials at elevated temperatures. The brittle-ductile transition temperature ranges of GaSb and InSb are sufficiently low to permit hot-filing operations. Therefore, high-purity, polycrystalline GaSb and InSb were filed in an argon atmosphere at 400' and 300°C, respec-

Jan 1, 1959

By F. E. Buch

The smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The :smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pet moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pet oxide copper. The predominating minerals are chalco-cite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. General Description Flotation concentrate, containing 10 Pet moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and Spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which Prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been Set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1949

By S. E. Szasz, E. J. Moore, B. F. Whitney

An accurate value of formation water resistivity R, is essential in calculating formation porosity and fluid saturation from electrical well logs. In the cases where R, has not been measured directly, it must be obtained from other data, e.g., the SP curve. This paper deals with another approach: how to calculate R, from the chemical analysis of the formation water. INTRODUCTION It is known that the resistivity of aqueous solutions of pure salts depends on their concentration and on the temperature; the concentrations are given in MPL (mg of solute per liter of solution), or sometimes in ppm (mg of solute per kg of solution): MPL = ppm X specific gravity. Values for different pure salts are available in the literature, but not for solutions of mixtures which are of practical interest. The major component of the dissolved material in almost all formation waters being sodium chloride, it is customary to express the resistivity of formation waters in terms of equivalent sodium chloride concentration, i.e., the concentration of a solution of pure NaCl which has the same resistivity at a given temperature as that of the formation water under consideration. Thus, the problem of calculating R, from the chemical anaylsis can also be stated as how to convert the other constituents of the solute into equivalent NaCl concentration. Salts dissolved in water are at least partly dissociated into ions, and do not conserve their identity. If known amounts of several salts are dissolved in water, the solution does not necessarily contain the same salts in the original proportion, but perhaps some other combination of the ions, along with free ions in solution. This is why the chemical analysis of formation waters is often given in terms of ions, as if all dissolved salts were completely dissociated. Our problem then boils down to how to convert the concentrations of the various ions to equivalent concentrations of Na' and C1-. Dunlap and Hawthorne' have proposed to convert the concentration of all other ions to equivalent Na' and C1-concentrations by means of constant multipliers; e.g., 0.95 for Ca"; 2.0 for Mg"; 0.27 for HCO 3-; 0.5 for SO, -, etc. Their factors were based on measurements made at 68F on 26 formation water samples from the Texas Gulf Coast, ranging in concentration from 1,500 to 75,000 ppm. The Dunlap method is widely used in electric log interpretation, and is often extrapolated beyond its original concentration range. A comparison of R, values calculated by this method and values actually measured on formation water samples has shown large discrepancies, especially at higher concentrations. Therefore, two new methods were developed at Sinclair Oil Corp.'s Tulsa Research Center to calculate equivalent sodium chloride concentration from the chemical analysis of formation water samples. FUNDAMENTAL CONSIDERATIONS The resistivity of a solution, or its reciprocal the conductivity, at a given temperature is determined by the charge, concentration and mobility of the ions actually present. Monovalent ions such as Na' or C1- always carry the same charge. Compounds of polyvalent ions, however. may show incomplete dissociation, e.g., NaSO; + Na' instead of SO,-- + 2Na'. This happens especially in more concentrated solutions. Only very dilute solutions are completely dissociated, as assumed in the chemical analysis report. At higher concentration, the degree of dissociation depends not only on the nature and concentration of the particular salt under consideration but also on the nature and concentrations of the other solutes. Mobility of the ions depends on the viscosity of the solution. It also depends on the degree of hydration of the ions, which in turn is a function of the nature and the charge of the ions and also of the amount of free water available per ion, i.e., the total ionic concentration. The net effect is that the conductivity increases slower than proportional to the concentration, even if a solution contains only one salt such as NaC1, and is different for different salts (Fig. 1). Conductivity can even decline with a further increase in concentration, e.g., if additional salt is little dissociated but ties up some of the free water and/or causes an increase in viscosity. In solutions containing more than one salt, the contribution of one salt to the total conductivity depends not only on the fractional concentration of this same salt, but also on the concentration of all other solutes. A perfect method would give the conductivity or resistivity of a solution as a function of the concentrations of all solutes present. This is so complicated as to be impractical, and a simpler method must be found which is of acceptable accuracy. The Dunlap method, on the other hand. is too simple because it askmes that at any concentration the contrih-

Jan 1, 1967

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction .within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress.4,5? The theory of recrystallization is not in advanced state; if recrystallization data were obtained, in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed.27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

Organization Place Date 1919 American Chemical Society :.... Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago, Ill. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, 0. Sept. 29-Oct. 2

Jan 7, 1919

Organization Place Date 1919 American Chemical Society Philadelphia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society Minneapolis, Minn. Sept. 22-24 American Iron, Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers. Chicago, Ill. Sept. 22-27 American Steel Treaters' Society, First Annual Convention Chicago Ill. Sept. 22-27 National Exposition of Chemical Industries.... Chicago, Ill. Sept. 22-27 National Safety Council Cleveland, O. Sept. 29-Oct. 2

Jan 8, 1919

By Arthur West

IT is the purpose of this paper to describe briefly some recent large power stations for blast furnaces, where the blast is exclusively supplied by gas engines using furnace gas. The stations are given in the chronological order in which they were designed, in order to indicate the various improvements suggested by experience. Fig. 1 shows the blowing-engine station of the Bethlehem Steel Co. at Bethlehem. Although the picture shows only five blowing engines, the house now contains 11 engines. In the diagrammatic. plan the arrow shows the position and direction of camera. This station handles five modern blast furnaces of 450 to 500 tons capacity each. In this, as in all the other stations described in this paper, each furnace is blown by-two single tandem gas engines. Ten engines are thus required for five furnaces, leaving one single tandem spare engine. This spare capacity has been shown by several years' experience at Bethlehem to be adequate to insure continuous operation. The engines in the Bethlehem station are right hand and left hand, arranged in pairs. The outboard bearings of each pair are close together so that there is not room for passageway between them. On the right of the picture are shown the inclined drums communicating with the cold-blast lines outside of building, so that any engine may be operated on any furnace. The illustration shows four cold-blast gate valves with pipes passing through wall, but since the photograph was taken the drums have been extended to take care of a fifth valve for a fifth furnace. At the extreme back of the picture can be seen the tubs of three twin vertical-horizontal Southwark steam blowing engines, which, although of modern design and as good as new, are not operated because of the greatly reduced blowing cost shown by the gas blowing engines.

Jan 6, 1915

By YANG TSANQ WOO

THE method of making coke that has been adopted at the Kaiping and other collieries in northern China resembles, to some extent, the familiar bee-hive oven process of the United States, except that a kiln with permanent sides is used instead of a closed oven, and the products of combustion are drawn off at the bottom, In building coke-kilns in China, two circular holes, 8 ft. 6 in. in diameter at the bottom and 13 ft. in diameter at the top, are excavated in the ground, both being .connected at the bottom by a flue as shown in Fig. 1. The sides and bottom of the kiln are lined with fire-bricks, and covered with a layer of fire-clay, and a rectangular opening, 6 in. by 8 in., connects the bottom of each kiln with the main flue. Around the edge of the hole, and overlapping the lining, is a wall of fire-brick extending .2 ft. 6 in. above the level of the ground. An open space 5 ft. wide is left in this wall, through which the coal is carried into the kiln and the resultant coke removed. This space, of course, is bricked up during the time that the coking operation is being carried on. The wall is pierced with nine flue-openings uniformly placed around the circumference, each intervening space in the wall being strengthened with a brick buttress, as is shown in Figs. 2 and 4. The floor of the kiln, as well as the main flue, is lined with fire-brick. Before charging the coal, it is first placed in shallow bamboo sieves, 2 ft. in diameter, and immersed in a trough 10 ft. long, and 3 ft. wide, fed with pit-water; in which it is washed by hand. Fig. 3 shows the manner in which the washing is done. From 25 tons of good " dust" coal, 22.5 tons of washed coal are obtained. When ready to charge the coal into the kiln a temporary cone-shaped flue of fire-wood and lump coal is first built to a

Nov 1, 1905

By F. du Breuil, R. L. Mundell

Longwall methods to mine coal in the United States provide the potential advantages of greatly increased productivity, improved safety, and a higher percent recovery. However, use of longwall systems during the past 10 years has increased much more slowly than was anticipated. This paper discusses some of the problems inhibiting the increased use of longwall systems and a proposed research program to address one of the most critical problem areas.

Jan 1, 1981

By M. Muskat, R. D. Wyckoff, H. G. Botset

The flow of liquids through porous media is known to follow Darcy's law which states that the velocity of flow is proportional to the pressure gradient. This law is but a statement of the facts obtained from experimental studies and is, therefore, uncontroversial. It should be men-tioned, however, that it applies only when the flow is viscous in nature and that at excessive velocities which tend to produce turbulence, the velocity is proportional to some power of the pressure gradient, the exponent ranging from 1 to 0.5 as the degree of turbulence increases. However., experiments with media having permeabilities corresponding to those of actual producing horizons show conclusively that the actual flow of liquids in a producing horizon must be viscous except perhaps in the immediate vicinity of a well producing at a high rate. Therefore, one is justified in assuming Darcy's law to hold for cases of practical interest, as will be implicitly assumed in this discussion Given this basic law of flow it is possible, theoretically to obtain solutions to any problem of viscous flow of dead liquids1 by the usual methods of potential theory. However, problems of practical interest often present such complex geometrical configurations of sources and sinks (driving sources and output wells) as to make the analytical solutions extremely difficult or even impossible. It is useful, therefore, to note that Darcy's law is precisely equivalent to the law of electrical conduction, so that the pressure distribution in steady state porous flow of liquids is exactly the same as the potential distribution in an electrical conducting medium.2 This analogy permits the use of electrical models wherein the potential distributions may be measured with far greater facility and accuracy than is possible in actual fluid-sand models. Such electrical models were used in determining the pressure distribution about complex arrays of wells, an example of which will be shown later in the discussion of the 5-spot flood. One phase of the porous flow problems which is of considerable practical interest involves the tracing of an advancing fluid front. Thus,

Jan 1, 1933

By Kenneth K. Humphreys, F. R. Zachar, A. G. Gilbert

INTRODUCTION by F. R. ZACHAR and A. G. GILBERT Coal producers are not only faced with the problems of mining coal, but must also decide to what extent they can invest capital and what operating and maintenance expense they can afford, after mining, to market their product in sufficient volume and at a reasonable profit. Regardless of whether the operator is contemplating a new operation or merely considering expanding present facilities, market requirements, ability to make a product meeting requirements, probable costs and possible future changes in raw coal or finished product must be considered. In addition, such items as flow sheet, structural designs, storage facilities, etc, must be examined individually and collectively. In estimating preparation costs to meet predetermined market specifications, the operator must calculate the economics of present preparation practices to anticipate the increase to total production which results when the quality of the finished product is increased. The consumers of coal are continually seeking to obtain the best and most adaptable product for their money. Regardless of whether coal is used for coking, industrial requirements, electric power generation, domestic fuel or for other purposes, it will be scrutinized from such standpoints as delivered cost, suitability for utilization in certain equipment, ease of ash disposal, adaptability to material handling system plans and its potential for generating dust problems. Utilities, due to large capacity volume requirements, are generally in a position to select coal that will result in the lowest over-all cost per million Btu. Freight costs, paid by the utility, are important and are given utmost consideration when a coal is under consideration. Steel companies, whether producing or purchasing coking coal, are continually seeking coal that will result in lowering the cost of pig iron production. Since it is usually necessary to clean to lower specific gravities, say 1.40, to turn out a product meeting metallurgical requirements, it follows that a high ash "middling" product is created. These low quality middlings do not command a good price. Therefore, unless the metallurgical coal can command sufficient realization to carry or subsidize the middlings, the operator may be ahead economically to prepare steam coal at a higher specific gravity. While the "unit-train" rate reductions have been helpful to the economy of the coal industry, the establishment of these rates has made mandatory the installation of storage and rapid car loading facilities at mines and plants shipping utility coal (see Chapter 15). A study of the economics

Jan 1, 1968

By P. H. Brace, N. A. Ziegler

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time. THE FURNACE Our furnace may be described as "a high-frequency induction furnace of the bell-jar type." It is similar in a general way to that described by Cain and Peterson' though we have introduced certain refinements of

Jan 1, 1928

By Charles S. Robinson

Abstract-The Henderson ore body is east of the Continental Divide in the Front Range of the Colorado Rocky Mountains, about 80 km (50 miles) west of Denver. The ore body is being developed for mining by workings that extend more than 1100 m (3500 ft) below the topographic surface. During construction of the mine workings, ground water in fractures in crystalline rocks has been encountered. From 1969 to 1973, Charles S. Robinson B Associates Inc., in cooperation with the engineering and geologic staffs of the Climax Molybdenum Company, a division of Amax Inc., studied the ground water geology of the Henderson mine development area. Detailed geologic records of the Henderson mine were available as a result of the exploration, evaluation and development of the mine. Records of the flow, chemical composition and temperature of the ground water at and near the surface, from the entire mine, from portions of the mine, and from exploration holes drilled in the mine, were kept as the mine was developed. Where possible, ground water pressures in drill holes and changes in pressure with time, were recorded. The geologic, hydrologic and chemical data were correlated. The following conclusions were drawn from the correlations: The ground water in the Henderson mine occurs in fractures in Precambrian igneous and metasedimentay rocks and in a series of Tertiary intrusive rocks. Two zones of ground water were recognized; an active zone, in which the fracture systems are recharged and discharged annually into the surface water system, and a passive zone, in which the fractures were filled with water in the geologic past Discharge from the passive zone is through mine workings that intersect the fracture systems. Discharge from a fracture or fracture system is initially high but decreases with time. The rate of decrease inflow (or pressure) is exponential. By measuring the change inflow with time, it is possible to calculate the amount of flow at some given period of time in the future. Based on changes in rate of flow and pressure, and the geology, and assuming rates of mining of the ore, it will be possible to predict the volumes of water that will have to be handled during the life of the mine and the area around the mine that will be drained by the mining operation.

Jan 8, 1978

By M. C. Flemings, G. E. Nereo

General expressions are given to describe macro-segregation in castings and ingots which results from mass flow of solute-rich liquid to feed solidification and thermal contractions. Analytical solutions are given for solidification with planar isotherms (unidirectional and bidirectional heat flow). These solutions describe inverse segregation and centerline segregation. Numerical examples are given for A1-4.5 pct Cu alloy. In 1540, Vannoccio Biringuccio published one of the first references to macrosegregation, describing the problem of exudation and inverse segregation in the manufacture of bronze gun barrels.' Since then, a great many studies of macrosegregation have been reported. Recent work of particular engineering interest includes that of Marburg 2 and others:" on centerline segregation and other types of segregation in large steel ingots, and work of Adams,5 Scheil, 6 and Kirkaldy and youdelis7 on inverse segregation in nonferrous ingots. In most studies on this subject, the various types of macrosegregation have been treated as separate phenomena. For example, quite different mechanisms have been proposed for formation of centerline segregation, negative cone of segregation, inverse segregation, banding, and so forth. In this, and in several papers to follow, it is proposed that these as well as other types of macrosegregation result from the same basic mechanism and can be quantitatively described by the same basic equation. It has often been suggested that some types of segregation (such as centerline segregation and banding) occur as a result of buildup of solute at the tips of growing dendrites.2-4 ,8-10 As example, banding can be induced in centrifugal castings by mechanical vibration, and Northcott 10 suggests this might be due to the influence of the vibration on the boundary layer at the dendrite tips of the growing dendrites. However, in view of the extremely small boundary layer known to exist at the tips of the dendrites,11,12 any interpretation of macrosegregation based on this boundary layer is clearly incorrect. Note that experiment has shown that significant buildup of solute does not occur at dendrite tips in ingot solidification, but even if such buildup occurred the thickness of the enriched zone would only be the order of D/U where D is liquid diffusion coefficient and U is dendrite tip velocity. For usual casting or ingot solidification this solute-enriched layer is 10"3 cm, far too small to account, for example, for centerline segregation.11'12 It has also been suggested that convection in the bulk liquid (ahead of the advancing dendrites) might cause segregation by sweeping away the solute-rich boundary layer in front of the dendrites.3 However, since there is no significant boundary layer, this explanation must be incorrect. The convection might directly cause segregation by penetrating between the dendrite arms, and presumably in a rimming steel ingot it is sufficiently vigorous to cause some segregation in this way. Centerline segregation, however, cannot be interpreted as resulting from this convection since a sharply segregated zone is usually found near the centerline, with the bulk of the ingot being nearly of nominal composition. If convection in the bulk liquid were the direct cause, a gradual change in ingot composition over the entire cross section would be expected. It is known that sudden changes in convection of the bulk liquid during solidification can result in banding,14 but it is not clear that the banding results directly from the effect of convection on solute distribution. Changes in convection also affect thermal conditions in the liquid-solid region of a solidifying ingot. It will be seen later in this paper, and in a paper to follow, that macrosegregation is strongly influenced by these thermal changes. Recognizing that in some cases of ingot solidification (as in solidification of rimming steels) convection in the bulk liquid may have a direct effect on solute distribution, we neglect it in this paper and in the several to follow. We then derive general expressions describing macrosegregation which results from the mechanism of interdendritic flow of solute-rich liquid

Jan 1, 1968

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By R. B. Woodworth

INTRODUCTION IN the sinking of bore holes, there are but two fundamental operations -drilling and hoisting,-which determine in the main the character of drilling mechanism and structures. There are endless ramifications, however, in the execution of these fundamental operations, according to the purposes for which the bore holes are drilled, their maintenance after completion, the protection and convenience of workmen, etc. The three main lines of use for bore holes are in mineral exploration, the sinking of water and salt wells, and the exploitation of petroleum and natural gas. This paper has to do more especially with the last. Here again there are many divergences. Wells may be drilled by either the percussive, the hydraulic, or the abrasive method. Finally, each of these methods, as applied by drillers of diverse nationalities, has followed somewhat different lines of development. The American system of cable-tool drilling has perhaps had the widest application; the hydraulic rotary is also in extensive use; but the Canadian system, the Galician system, and the Russian free-fall system all have their points of recognized merit and are preferred by operators accustomed to their use. These differences in drilling procedure, which rest ultimately on essential variations in geological conditions, are reflected in the chilling structures as well as in the drilling mechanism. The purpose of the present paper is to record those stages in the development of the application of steel to the construction of drilling mechanism and structures with which the writer has been intimately associated, and to contribute to the history of the art of drilling other data acquired in the course of his personal investigations. It is necessarily limited by reason of space to American practice, with especial reference, therefore, to the cable-tool system and the hydraulic rotary method of drilling wells for oil and gas.

Jan 11, 1915

Edward A. UehliNg, New York City (communication to the Secretary*):—In adding my mite to the discussion, I wish to touch on a few points which bear emphasizing and perhaps a little further elucidation. Mr. Grammer says that he "found the electric pig-breaker at Duquesne, if used in connection with the iron-chill, less expensive and more satisfactory " thau the casting-machine. The cost of handling the iron over the Duquesne casting-niachine is about double the average cost of the other Uehling machines at the several Carnegie plants. It is nearly as expensive to run as the Hey1 & Patterson machines, and while Mr. Grammer's statement is, no doubt, true, as applied to that particular machine and breaker, it should be borne in mind that the machine at Duquesne had embodied in it several new features, which were not improvements; also that it was taxed beyond its economic capacity. The machine at the Lucy furnaces under the management of Mr. Scott handled the output of the two furnaces, and saved

Jan 1, 1905

By R. H. Ogburn

THE GROUND now being worked by the Fairbanks Exploration Co., near Fairbanks, Alaska, has been known to be gold bearing since 1901. In the early days it was worked by drift mining and other small-scale methods. In 1922, Hammond started prospecting the gold-bearing ground and obtaining options on the properties desired. Two years later the present Fairbanks Exploration Co. started taking up the options, and preparing to exploit the ground. For the prospect drilling Keystone drills were used, with holes at the points of equilateral triangles 600 ft. apart. Holes were also put down more closely spaced to determine the limits of dredging ground. In the first drilling casing was used to the bottom of the holes, but in later work the casing was put down only to the bottom of the thawed ground, and the rest of the hole put down without casing. The gold content was determined by panning, each 2 ft. of depth being determined separately. Where no casing was used the size of the hole was determined by using water to measure its volume. The greatest concentration of gold occurs at or near bedrock. All the gold-bearing streams head in one big dome. Gold, however, is not found clear to the head of the creeks, the pay being first found some distance downstream from the head.

Jan 1, 1933