Search Documents

By John Hillman

The reconstruction of the British mining industry which began shortly after nationalisation in 1947 continued until well into the 1950s with the support of the Government. This support diminished as plentiful supplies of cheap oil from the middle East made many coalmines un¬economic. The planned rundown which followed was foreshadowed in the 1965 White Paper which outlined the financial measures to speed the closure of uneconomic collieries. The decline appeared likely to continue into the 21st century as the role of coal in UK energy requirements became less and less significant. This policy was well on course in 1973 when the oil crisis led to a complete reappraisal of the position. A Government examination in 1974 of the coal industry then supported the National Coal Board's general strategy of major capital investment as set out in its 'Plan for Coal' (1). Plan for Coal aimed at halting the intended decline in the industry's capacity and restoring it to 120 million tons of deep mined output in 1985. The Plan proposed action along the following lines (a) increase output by major Investment in construction at existing collieries with sufficient reserves to give 13 million tons per annum extra output (b) invest in extending the life of existing collieries by gaining access to additional reserves, to give 12 million tons per annum extra output © by sinking new mines, produce an extra 20 million tons per annum. Figure 1 shows the contribution (2) expected from each of the three sources up to 1990/1. The measures taken were expected to offset the inevitable exhaustion of existing pits and provide the additional 40-42 million tons capacity needed to restore annual output in 1985 to 120 million tons. Parallel to this programme for expansion of deep mined output, opencast mining was to produce 10-15 million tons per annum. A recent review however, indicates that new mines are likely to yield only 10 million tons per annum by 1985, mainly owing to the need for public inquiries into proposals for new mining and the resultant fact that planning approval takes 'much longer than originally expected. Nevertheless the objective of 120 million tons deep mined output by 1985 is still considered achievable of means of a greater contribution from existing mines. This programme was originally estimated to cost 2,-56 million dollars at March 1974 prices, out revised estimates of the cost of Plan for Coal indicate that it may now exceed 6,960 million dollars at mid-1977 prices. Plan for Coal includes a substantial investment in new and reconstructed coal preparation plaints. At mid-1977 prices more than 322 million dollars Ls so be invested in coal preparation projects in the UK, at the rate of, about 70 million dollars a year. This rate 3f capital expenditure has been maintained over the past three years and covers investment in a wide range of coal preparation coals for the power station, coking and domestic markets.

Jan 1, 1978

By Frank H. Buchella

Principal factors influencing equipment selection can be grouped into five basic categories. Tonnage Requirements, Ore and Waste Loading, transporting, and ground preparation equipment are largely determined by tonnage requirements. Generally, the greater the tonnage requirements, the larger the equipment size selected. Large size equipment is appropriate for a production of about six million tons (total) per month, medium size for three mil- lion tons, and small size for one million tons or less.

Jan 1, 1973

By Y. Wang

Wet magnetic separation methods for recovering hematite and chromite fines and ultrafines are investigated in this paper. These methods include wet high intensity and high gradient magnetic separations, carrier or "piggy-back" magnetic method, magnetic field-induced aggregation and magnetic seeding. This investigation indicates that wet magnetic separation is more efficient for fines and ultrafines whereas other methods can be used to enhance the particle aggregation and/or the magnetic response. The magnetic behaviour of these minerals with respect to magnetizing field, particle size and temperature is also presented.

Jan 1, 1993

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By V. R. Burkhart

Pennsylvania Power & Light Company is an investor-owned public utility which was incorporated under the laws of the Commonwealth of Pennsylvania on June 4, 1920, with general offices at 901 Hamilton Street, Allentown, Pennsylvania. At the present time PP&L is operating five coal-fired steam electric stations, two hydroelectric stations and one steam heat plant which is being converted from anthracite to oil fired. In addition, PP&L is a partner in both the Keystone and Conemaugh mine mouth bituminous coal-fired steam electric stations in Central Pennsylvania and also part owner of a company which operates another hydroelectric station. PP&L plants, other than the two mine mouth stations, are located in Central Eastern Pennsylvania. (Figure 1) The company derives about 99% of its operating revenues from supplying electric service, while the balance is from the one steam heat plant serving the city of Harrisburg. The entire service area covering 10,000 square miles in 29 counties, has a population of approximately 2,300,000 people. The area served is mostly suburban. It includes 109 communities each having a population in excess of 5,000 people. The largest cities served are Allentown, Bethlehem, Harrisburg, Hazleton, Lancaster, Scranton, Wilkes-Barre, and Williamsport which range from 50,000 - 120,000 in population. So you see our service area does not include any major cities. The area has industrial, commercial, residential, agricultural and recreational activities that are linked with the Eastern Megalopolis by an extensive interstate limited-access highway system and railroad networks. We consider this Central Eastern Pennsylvania area we serve as the "heart of the market" -- an area with great growth potential.

Jan 1, 1973

By Wayne W. Murdy

Peru is a mineral hot spot in the world today. Newmont is in the exploratory phase of this mining cycle, a phase full of optimism and expectations. But exploration is high risk. There will be successes but also failures. Many foreign companies will come and go. But it is the responsibility of the mining industry leadership of Peru and the government to continue to foster an environment conducive to investment. This is the time of year companies begin planning their next annual report. Last year, Newmont’s was called “new horizons.” It highlighted the company’s global expansion into Peru, Uzbekistan and Indonesia. Now, projects that were only on the horizon a year ago are moving into production. So “turning opportunity into gold” may be this year’s theme.

Jan 1, 1996

By C. Frenzel

Tunnel boring machines (TBM) utilize disc cutters as the primary means for excavating hard rock. Depending on rock excavatability and rock abrasivity disc cutters can exhibit significant wear. A detailed analysis has been carried out to characterize failure modes and wear patterns of disc cutters. The relationship between rock properties, op-eration of the TBM, and failure modes of cutting tools is clearly high-lighted. On that basis a prediction tool for disc cutter consumption has been developed that allows to estimate not only gross cutter life, but accounts for cutterhead design, premature cutter changes, and disc cutter repair costs.

Jan 1, 2011

THE QUARTETTE Mine near Searchlight, NV, a mine that first operated in the 1890s, could begin processing ore again by September. Jetco Enterprises Inc. plans to work through the tailings and ore close to the surface followed by plans for an openpit mine. It is one of at least three new mining efforts in the region, the Associated Press reported. Another is north of Searchlight, with yet another across the Colorado River in Arizona, east of Bullhead City. Gold mining is rare in southern Nevada. The area generally lacks the rock type that contains gold deposits. Restrictions on federal wilderness areas and protections for the desert tortoise also play a role. Gold veins in the region are generally small and erratic in length and height, Bill Durbin, a geologist and chief of southern Nevada operations for the Nevada Division of Minerals told the Associated Press. L.R. Tad Tinnell, president of Jetco Enterprises, has long eyed the mine. From 1993 to 1995, he explored and drilled on the property, which was still owned by Searchlight Mercantile.

Sep 1, 2013

By T. J. Batchler, K. M. Mohamed, D. F. Gearhart, R. K. Zipf

Seals are explosion-resistant structures built in underground coal mines to isolate abandoned mining areas from the active workings. An equivalent single degree of freedom (SDOF) method such as the single-degree-of-freedom blast effects design spreadsheet (SBEDS) developed by the U.S. Army Corps of Engineers can be used to design seals to resist mine explosions. The critical input for the SDOF code is the seal resistance function. The objective for this study is to develop engineering data for design of plain concrete (PC) and reinforced concrete (RC) seals using finite element (FE) models. The FE models can then be used to generate resistance functions for different PC and RC seal designs, which can be used in the SDOF codes. The U.S. National Institute for Occupational Safety and Health (NIOSH) researchers designed and built a test fixture for use in conjunction with NIOSH’s Mine Roof Simulator to apply a four-point bending load on the face of the tested seal. Eight large-scale experiments for each PC and RC seal were conducted. The experimental design considered the effects of the foundation strength, hitching and roof-to-floor convergence. Calibrated FE models for PC and RC seals were developed using ANSYS Ver. 13. With a very limited number of engineering-based assumptions and a single set of data—including Young’s modulus, compressive strength, stress-strain relationships, etc.—the PC and RC seal models successfully calculated the recorded resistance functions and failure patterns for a wide range of boundary conditions. Plug and RC seals were assumed for a 1.83-m- (6-ft-) high entry to demonstrate the application of the calibrated finite element models for calculating the resistance functions of these seals. The resistance function of a particular plug seal case was found to be a bilinear relationship. The resistance function of a particular RC seal without shear reinforcement was found to be a nonlinear relationship.

Jan 1, 2013

By C. Anderson, B. Schug, C. Cristoffanini, S. Nazari

The Haile Gold Mine in South Carolina is increasing the automation level of their processing plant in order to improve operational stability. One step towards this goal is the application of a Digital Twin concept to provide Virtual Instruments. Haile has engaged ANDRITZ to implement Virtual Instruments at their grinding area hydrocyclones and at their tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The Digital Twin is a first principles IDEAS1 ™ simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions, and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters. INTRODUCTION OceanaGold’s Haile Gold Mine is located near Kershaw, South Carolina, about 50 miles southeast of Charlotte, North Carolina. This location was first mined in 1827, and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October, 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile Operation. The current operation began in 2017 as an open pit mine with additional underground resources. The nameplate throughput is 6,350 tpd ore, and 2017 production was 118k oz gold, with 140 to 155k oz gold expected in 2018. Proven and Probable reserves exceed 3 Moz. The process, as shown in Figure 1, includes a primary jaw crusher, comminution with a Semi-Autonomous Grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon in leach (CIL) leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile Operation’s inaugural gold pour took place January 20, 2017. Mine life is expected through at least the year 2030. Based partially on prior experience of some key OceanaGold personnel with automation services from ANDRITZ on other projects, OceanaGold decided to include ANDRITZ on the Haile project. The scope of these services for Haile included design and supply of the process control application software, an ANDRITZ dynamic process simulator for operator training, and ANDRITZ Advanced Control Expert (ACE) ®2 systems for the SAG mill, ball mill, and rougher flotation areas. Since startup, ANDRITZ has continued to provide services for the site, particularly related to PLC and HMI equipment, programming and support, ACE system expansion, and the implementation of Virtual Instrumentation. The implementation of this new Virtual Instrumentation technology at Haile is consistent with Haile goals: increased automation, a change in the role of the operator from interactor to monitor, and improved stability by removing human error.

Jan 1, 2019

By C. A. Rowland

The use of the Bond Work Index to size industrial grinding equipment is well known. Its use to measure grinding efficiency was presented by C.A. Rowland, Jr. at an AIME meeting in 1976. However, due to a bureaucratic error, the paper was never submitted for publication. This metric has nevertheless been adopted by industry as a widely used standard. The purpose of this paper is to re-present and update the application of this tool as a standard for measuring grinding circuit efficiency. Definition ?standard, n. something established for use as a rule or basis of comparison in measuring or judging capacity, content, extent, value, quality, etc.; as standards of weight and measure? (Webster, 1958).

Jan 1, 2008

By Robin P. Gardner

The development and use of short-lived radioactive tracer methods for the on-stream determination of residence time distributions in large-scale ball mills is described. Tests are reported on a pilot-plant ball mill with 0.43 m diameter and 0.86 m length and on an industrial mill with 1.83 m diameter and 2.74 m length. Tests with different tracer feed sizes indicate that the residence time distributions on both mills are independent of charge particle size. Similar tests are planned for a-large ball mill of 4.57 m diameter and 9.30 m length. No safety problems were encountered in these tests and none are anticipated in tests of the larger mill.

Jan 1, 1978

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By Y. C. Kim

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that Ordinary Kriging (OK) cannot easily handle. With the recent introduction of the nonparametric, distribution-free technique of Indicator Kriging (IK), the above problems can be solved. This paper describes the results of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blast hole information. The IK estimator, although a bit optimistic, performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion. OK was found to be very biased and pessimistic.

Jan 1, 1986

By Michael Gauna

A high seam geologic condition exists at Jim Walter Resources No.4 mine which requires immediate rib support after a continuous miner cuts a place, High seam mining heights are typically 2.4 to 2.6 m (8 to 9 it) and a thick rock layer is present in the upper portion of the coal rib side. The 610 m (2000 ft) mining depth at No. 4 mine induces horizontal rib line movement after excavating an entry. Horizontal rib movement greater than 30.5 cm (12 in) have been noted. When lateral movement occurs in the high seam areas, the thick rock layer, and the coal above the rock layer, become fractured and tend to roll into the entry. If not adequately supported, large rib rolls develop in the place being bolted as well as in previously mined areas which endanger men and equipment. To control this situation rib support must be installed in the roof bolting operation as the bolting crew works towards the face. A rib control system has been developed for this high seam mining condition utilizing a mechanical anchor bolt placed at an angle in the rib and installed with a modified Fletcher DDFI- 15 bolting machine. Over 120 km (75 mi) of entry have been supported with angle rib bolts. These angle bolts constitute 43 to 60% of the total roof and rib bolt footage in the high seam port- ions of No.4 mine. The angle rib bolting system has proven safer, more effective, and more efficient than the earlier support method employing bolts installed horizontally into the rib. No rib roll accidents have occurred since the angle drill bolting machines were placed in service in 1981. By securing the broken rib material with an angle bolt anchored above the coal pillar, a more effective means of rib control is achieved. Angle rib bolting does not interfere with continuous miner productivity. In addition, bolting crews are now reduced from three to two people and the total drilling supply costs are approximately 60% the previous cost, when compared to the previous support method using horizontal rib bolts.

Jan 1, 1983

By MOHAMED WAEL, ANASTASIA GOEVA, ABDULAZIZ TAWFEEQI, IHTISHAM TARIQ, S. M. ZAKIR HOSSAIN, NIAZ ALI KHAN, MUHAMMAD FAISAL IRFAN

Carbon capture and storage (CCS) is an attractive area of research in such fields as CO2 mineral carbonation, global warming and sustainable energy systems. In this study, carbonation efficiency for aqueous mineral carbonation (MC) was achieved through two steps,which include leaching of calciumfrom cement kiln dust (CKD) followed by the reaction of pure CO2 with the calcium hydroxide precipitates formed by the hydroxylation using NaOH. Response surface methodology (RSM) with a Box-Behnken design (BBD) was applied to optimize the calciumleaching yield,while the carbonation efficiency from CKD was assessed using RSMwith central composite design (CCD). Optimization of calcium leaching is highly important, as it is a rate-limiting reaction step in MC and also influences and enhances carbonation efficiency. Different parameters including acid concentration (HNO3), leaching temperature, leaching time, and dose of CKD sample were considered in order to optimize the maximum yield of Ca leaching from the CKD sample. In addition, different CO2 flow rates and temperatures were used as parameters for optimizing carbonation efficiency. Two quadratic regression models were developed for each process, i.e. calciumleaching and carbonation. For calcium leaching, a maximum of 98.55% calcium was extracted under the optimal set of acid concentration 4.13 M, 90 °C, 28 min leaching time, and 13.8 g of CKD sample. For carbonation, the maximum carbonation efficiency of 89.2% was achieved for a CO2 flow rate of 1163 cm3/min at 90 °C. Calcium leaching results indicate that the leaching yield was significantly affected by all the input parameters except leaching time. For carbonation, both factors affected the carbonation efficiency, with the effect temperature shown to be greater than that of the CO2 flow rate. Additionally, the predicted results agreed well with the experimental values for both calcium leaching and carbonation processes, with errors of less than 1% and 5%, respectively.

Jun 5, 2020

By M. Howe

This is a study of the impact of cyanide from mining waste on riparian communities, primarily vegetation, near Whitewood Creek, down-stream from Homestake Gold Mine in Lead, South Dakota. Cyanide is used in gold processing and the effluent, until fairly recently, was discharged directly into Gold Run Creek which empties into Whitewood Creek. Vegetation, soil, and water were collected from four different sites over a six month period, and samples tested for cyanide concentration. Data indicate a relationship between cyanide in soil and its uptake by certain plants, also, that the Homestake cleanup effort has made the stream viable again.

Jan 1, 1983

By Daniel G. DiCanio

Investigation of the costs of industrial accidents dates back to the 1920s. The Bureau of Mines was one of the pioneers in accident cost investigation with numerous studies published between 1928 and 1933. The bulk of these early investigations dealt only with costs which appeared as payouts on company books; that is, the direct cost of insurance premiums and the costs of medical expenses which resulted from industrial accidents. These early investigations, especially the Bureau's study of accident costs in Pennsylvania and Indiana coal mines provided the first real evidence that promotion of industrial safety pays back in dollars as well as in human life and wellbeing. In the 30s and 40s, investigations began to accumulate evidence that industrial accidents impacted more than just the direct operating expenses of a company (i.e., higher insurance premiums). The work of Heinrich pioneered these investigations, and produced strong evidence that the un¬insured costs of accidents far outweighed those costs covered by insurance. Heinrich developed and published a ratio of insured to uninsured costs of 1.4. Despite his cautionary statements about blanket application of this ratio it is used even today to estimate total costs of accidents. Simonds, in the late 40s and early 50s, extended the definitions of uninsured or indirect accident costs and developed what is now regarded as the principal method for estimating the total economic impact of industrial accidents. Simonds' method served as the basis for development of the logic of the Accident Cost Indicator Model (ACIM). However, several departures from Simonds' method were made to satisfy certain requirements imposed by the Bureau of Mines, and because information gathered during the course of our investigation justified a departure. These departures are noted in the discussion which follows.

Jan 1, 1977

By Yuemin Zhao, Daniel Tao, Rick Honaker, Maoming Fan

"Froth flotation is the most widely used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles around 700 nm in diameter can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubbles on the flotation performance of different particle size fractions of coal was investigated using a bank of 10-L flotation cells, a specially designed 50-mm inside diameter column and a 152-mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during the froth flotation process improved flotation efficiency. The use of nanobubbles in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.IntroductionFor minus 0.6 mm fine coal or minus 0.15 mm ultrafine coal particles, froth flotation is known to be the most efficient and the most cost-effective separation technique. However, flotation efficiency decreases sharply with ultrafine and relatively coarse coal particles. Studies have shown that the low flotation efficiency of ultrafine particles is mainly due to the low probability of bubble-particle collision (Yoon et al., 1989; Ralston and Dukhin, 1999). Enhanced flotation of fine and ultrafine coal can be achieved by increasing collision and attachment probabilities.The top size of particles that can be recovered by flotation depends on the combination of mineral properties and flotation devices. Turbulence in flotation devices is an important factor that affects the stability of bubble-particle aggregates. Even in the flotation of fine particles, bubble-particle detachment can significantly influence the kinetics of flotation taking place in mechanical cells, which provide intensive turbulent agitation (Deglon et al., 1999). Coarse particle flotation is more difficult, because increased agitation is required to maintain particles in suspension and coarse particles are more likely to detach under turbulent conditions (Mankosa and Kohmuench, 2002; Soto and Barbery, 1991). More efficient attachment of particles and improved flotation rate has been observed when tiny bubbles coexist with conventional-sized flotation bubbles (Attalla et al., 2000; Tao et al., 2010; Fan et al., 2010a, b, c, d; Fan et al., 2012)."

Jan 1, 2015