Search Documents

By Iain Weir-Jones

The efficient operation of an open pit mine presupposes that the slopes are maintained at an angle which closely approaches that of the ultimate stability of the slope. In order to do this in a safe manner, it is essential that the data relating to the behavior of the slopes be monitored and made available, through an instrumentation system, to the appropriate personnel so that soundly-based engineering decisions may be reached with the minimum of wasted effort. In addition to simply detecting potential failures, the system should also define what type of failure is developing; i.e., rotational, wedge, or dilational failures. Providing this data is the prime function of a stability monitoring system. Therefore, in an operating open pit mine, the instrumentation system must provide information which will have a direct bearing upon both the safety and the economics of the operation, as well as provide data which is pertinent to initial design, or to the re-design of slopes where developing instability is found to be a problem.6 It is possible to excavate pit slopes which will remain stable under extremely adverse conditions; however, such slopes would usually be so flat that they would tend to render the operation of a pit uneconomical which might otherwise be mined at a profit. On this basis, all practical pit slopes must be considered to be, to some ex- tent, unstable; if they are not, the design is too conservative and the mine is not returning its maximum profit. To reduce the problem to its fundamentals, one can simply state that the ideal pit slope design produces a slope which stands with zero maintenance for the entire life of the pit and then collapses into the final excavation as soon as the personnel and equipment have been removed. Such a design is impossible to achieve, but the fact remains that an efficient slope would hover on the edge of failure for the life of I the pit. As one retreats from this position, the profitability of the mine decreases because of an unduly conservative design.

Jan 1, 1975

By R. C. Bratton, R. Q. Honaker

Hindered-bed separators are recognized as low-cost, high-capacity devices for both classification and density separation; however, since their inception, there have been few significant advances in the fundamental technology. Recently, Eriez has shown through modeling and pilot-scale testing that the innovative approach to feed presentation offered in the CrossFlow teeter-bed separator provides improved metallurgy when compared to traditional hindered-bed classifiers or single-stage coal spirals. This design feature prevents excess water from entering the separation chamber and disrupting the overall fluidization flow rate within the teeter zone. Most recently, a side-by-side industrial scale evaluation has verified that this technology improves overall efficiency and simultaneously reduces the separation cut-point. With regards to coal processing, data from full-scale units indicate that the CrossFlow offers good separation efficiency, high unit capacity, and metallurgical results consistent with laboratory- and pilot-scale separators.

Jan 1, 2006

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012

Newcrest Mining is one of the leading independent gold producers in Australia thanks in large part to its Cadia Valley operations. It is the largest gold and copper producer in New South Wales and one of the largest in Australia. This year Newcrest will expand its operations with a A$545-million expansion in the area. The Cadia Valley is approximately 250 km (155 miles) west of Sydney. The province presently includes the Cadia Hill opencut mine and the Ridgeway underground mine. With a significant mineralized system to the east of Cadia Hill and a mineral resource below Ridgeway, Cadia Valley has the potential to underpin Newcrest?s production for up to 30 years. In 2007, total gold production for the company in-creased to more than 50 t (1.6 million oz) and cash flow increased by 47 percent, according to the company?s annual report. The history of mining in the area dates back to 1851, but Newcrest?s history is young. In 1990, Newcrest commenced activities in the Cadia Valley. In 1992, Cadia Hill was discovered, with the discovery of Cadia East (1995) and Ridgeway (1996) following close behind. In 1998, the Cadia Hill openpit mine was commissioned. In 2002, the Ridgeway underground mine was commissioned and in 2007 the company?s board of directors approved an A$545 million development of the Ridgeway Deeps. The Ridgeway underground mine is located adjacent to Cadia Hill. The Ridgeway orebody has no surface expression but lies approximately 500 m (1,640 ft) below the surface and resembles an inverted teardrop. It measures approximately 450 m (1,476 ft) by 250 m (820 ft) and extends in excess of 850 m (2,788 ft) in depth. Ridgeway is a sublevel caving operation. Crushed ore from underground is delivered by conveyor to a surface stockpile, adjacent to the Ridgeway concentrator. Using similar processes to the adjacent Cadia Hill concentrator, gold and copper are recovered in a conventional flotation circuit to produce a copper concentrate containing elevated gold levels. Ridgeway concentrate is combined with the Cadia Hill concentrate before it is pumped to the filtration plant in

Jan 1, 2008

As opposed to a prescriptive-based design, a performance-based fire-protection system design allows the system planner the flexibility in choosing specific method, materials and design tools to achieve a preset goal. A different approach in fire protection and a powerful addition to existing method, the system has been around for many years, and has gone through numerous improvements. Despite its popularity in the building industry, it has not been introduced to the mining industry yet. As mines get deeper, increases in size and complication, mine fire safety system will also become increasingly challenging, a new and proven system should be able to great potential to eradicate many of the problems that are either unsolvable or cost-prohibitive with the traditional method. With increasing globalization and international exchange with other major mining countries a common language/practice also make the performance-based design method a desirable feature in mine fire safety system. This paper will first define a performance-based system, step-by-step design methods, likely impacts on fire-protection practices and possible challenges in implementing the system in US underground mines.

Jan 1, 2011

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By D. M. Loring

Radon progeny have been a health and safety concern for miners since the mining of radioactive minerals began. Through the ?nuclear age?, it has become better understood and the regulations have become more robust. Ventilation and control practices have improved, thus reducing miners? exposures. This paper provides an overview of radon in mining, the progress of the regulations, and discusses some of the uranium miner studies that contributed to the knowledge of the pathology of radon.

Jan 1, 2009

By Paul D. Tomlingson

World class performance is the ultimate objective of many maintenance organizations. It marks the organization as a leader in its industry and sets it apart as the ultimate achiever. But what is a “world class” standard and how can it be achieved? Is there a yardstick by which an industrial organization can measure the relative performance of its maintenance activity and compare it with performance levels that universally identify “world class” status? Are there financial formulas, achievements, evaluation techniques or indices that provide this yardstick?

Jan 1, 2006

By Charles Ronkos, Jeffrey Edwards, Brian Brodsky

The Marlin gold-silver deposit is in western Guatemala, 15 kilometers south of a major transform fault that separates the North American and Caribbean plates. A district-scale, northwest-trending graben controlled deposition of a greater than 1200 meter thick upper Tertiary quartz latite to rhyolite volcaniclastic sequence. These volcanics were subsequently intruded and unconformably overlain by a small intermediate, latite to andesite, volcanic complex. Classic low-sulfidation, quartz-calcite-adularia veins and stockwork formed a 2.2 million ounce gold deposit, in association with late-stage andesite dike swarms, along a west-northwest striking normal fault on the eastern flank of the volcanic complex.

Jan 1, 2005

By B. K. Belle

The beginning of 21st century has heralded the global strategic importance, as evidenced by increase in energy prices and energy generation-emission-utilization dilemmas. In January 2008, the South African energy supplier, ESKOM had tabled the concept of power conservation and acknowledged the energy crisis until 2016. The concept is required of all energy users to reduce their electricity consumption, intensify energy efficiency and cautiously proceed with new projects. The generation of energy results in by-products called ?green house gases? (GHGs). To make a positive response to climate change and their effect on the environment, every energy user must ensure efficient energy use through technical and administrative means referred to generally as energy savings. This paper identifies mine ventilation engineering, in particular the electricity consumed by main fan units, as an area of potential energy savings. For a major mining company, electricity consumed by main ventilation fans alone can be in the order of 120 MW. Although a known fan engineering technique but scantly applied technology identified as the Hermit Crab can be seen as a ?quick win? project, due to its success in other industries such as cement and steel. The ?Hermit Crab? technique® involves upgrading or replacement of an impeller - whatever its origin - with a design impeller to suit the actual ventilation requirements, resulting in increased fan efficiencies. The cash flow benefits associated with a case study and its rollout of this technology have been calculated. For a 10% increase in main fan efficiency, would have a net present benefit of US$ 16.08m over 10 years. With the inclusion of carbon credits, this benefit rises to US$ 29.40m in total. Application of other available technologies, viz., composite materials, ventilation-on-demand and variable speed drives are discussed.

Jan 1, 2009

By W. A. Wilkinson

Mine planners are under pressure to evaluate the impact of changing economic times and newly acquired data on their mine plans. Incorporating changes such as commodity prices, customer sales, fluctuating cost assumptions and newly acquired geologic data requires quick turnaround for model building and planning to keep mine plans on pace with changes as they occur. Because of the length of time required to perform some of the geologic modeling and mine planning tasks, planning frequency may not be keeping pace with the frequency of change. To meet these challenges, one leading North American mining company successfully increased the frequency rate and accuracy of its mine plans to stay current with incoming data, ensuring its mine plans reflect the latest information, thereby minimizing or eliminating production cost variance.

Jan 1, 2010

By Xiaochun Xiao, Xin Ding, Yishan Pan, DI WU, Xiangfeng Lv

Rockburst is a sudden disastrous instability of coal mass that poses a serious threat to underground exploitation of coal resources; therefore, approaches of prediction and control methods are valuable for improving mining environments. The mechanical properties and bursting liability of coal with drying, under-saturated, and saturated moisture content under uniaxial compression are investigated, and the charge induction signal during coal deformation both in the laboratory and on-site is recorded in this study. The presence of water reduces the cohesion and increases the internal stress caused by non-uniform deformation of minerals, resulting in the strength, elastic modulus, and bursting liability being weakened. The charge induction precursor main frequency band is 1–100 Hz and belongs to the very-low-frequency signal regime, and it indeed varies with the loading stage, leading to specimen failure owing to changes in amplitude and continuity of the charge pulse in both the time and frequency domains. Water inhibits the richness of charge induction and reduces the bursting liability, and the earlier the precursor appears, the more total charge emerges. Moreover, measurement results indicate that the amplitude and continuity of the charge pulse decrease over a longer time, as recorded in a coal seam with water injection, further verifying the weakening of the coal dynamic characteristics. Charge induction can be a valuable tool with which to obtain the precursors for rockburst and to aid the evaluation of water injection.

Dec 26, 2022

By C. K. Kocsis

A study was undertaken to evaluate the thermal environment and determine the contributing heat sources within the existing 153 Orebody of Coleman/McCreedy East Mine which would then enable the prediction of the climatic conditions in the mine?s future 170 Orebody. The study entailed continuously monitoring, for a 2-week period, the dry-bulb temperature, humidity and barometric pressure along the existing intake airways from surface down to the 4810 Level and throughout an active mining area on that level. Furthermore, the mining activities and associated equipment that could be responsible for any changes in the temperature and humidity conditions within this mining area were also monitored. These data were then used to develop and validate a climatic simulation of the mine?s mechanized cut and fill mining method. This climatic model was then transposed to the future 5700 Level in the deeper 170 Orebody, to determine the environmental conditions within its production workings and along the main haulage route ascending from that area. Based upon the simulations performed it was shown that the level of ventilation planned for the new orebody should be able to maintain adequate environmental conditions. However, this study did emphasize the importance of the appropriate distribution of airflow in workplaces that used auxiliary ventilation in order to sustain a suitable thermal environment.

Jan 1, 2009

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By A. W. Popp

After forty years of exploration and development, the heavy mineral sand deposits of the Murray Basin are on the eve of substantial exploitation by Iluka Resources Limited, Southern Titanium NL and RZM/Cable/Bemax, whom plan to initiate mining and processing operations in 2005. A trial mining and processing operation was undertaken on the Wemen North strandline deposit in 2001-2003 by Murray Basin Titanium, a joint venture of Sons of Gwalia and RZM/Cable, which brought to light a number of mining and processing problems which have since been the subject of extensive studies and process development work. The mineralogy of these weathered strandline deposits is complex by industry standards due to the variety of the heavy minerals present, coatings on the mineral grains and the extensive weathering and alteration which has taken place during the past 50 million years. This paper provides an overview of the complex mineralogy that, in turn, dictates the processes that can be used to recover the valuable heavy minerals. The Murray Basin encompasses some 300,000 km2 and has been a depositional basin, often land locked, since the start of the Cenezoic Era. The economic heavy minerals include ilmenite, altered ilmenite, leucoxene of highly variable composition, rutile, and zircon. There are also other heavy minerals present such as cassiterite, chromite, and monazite in quantities that pose both problems and opportunities. The clay content and overburden thickness also play a major role in the selection of the deposits to be mined. Project Services Consultants (PSC) has undertaken the preparation of this paper as part of its ongoing participation in the mineral sands industry and in particular the project development activities in the Murray Basin region currently being undertaken by Iluka Resources. PSC has been involved with the mineral sands business for several years with senior staff having in excess of 30 years global industry experience. The company is well placed to provide a range of services to clients like Iluka Resources in the areas of project development, execution and strategic development and industry advice.

Jan 1, 2005

By Ebrahim Tarshizi, Livernois Ryan, Emily Sarver, Zoe Scopa, Robert Setterlind, Leah Frost

"The mines of the future present a host of challenges, which may appear exciting or daunting, depending on one’s perspective. Whether some sectors of the public recognize it or not, the demand for raw resources is not going away any time soon. In fact, it is rising, as the global population grows, urbanizes and attempts to steadily increase quality of life. Yet, at the same time that much of the highly developed world is calling for greener goods, reduced consumption and cleaner production, in other areas there are cries for clean water and sanitation, consistent energy supply, access to health care and education, personal security and support for basic human rights. The balancing act for sustainable development of our global society is, indeed, precarious and the mining community is a key player. Fortunately, many industry members have accepted this role and the responsibility to provide leadership and a solid foundation for progress. Looking ahead, we need new generations of leaders, including many mine engineers who are ready to tackle all sorts of complex problems.There are tremendous needs just for technological innovations. Increasingly tough deposits will require that the industry continues to expand scale toward “mega pits” and “super caves;” fully develop unconventional recovery techniques like in situ leaching and gasification or deep-sea extraction and seriously consider off-earth endeavors. Such work will take entirely autonomous equipment, novel separations, processing and recycling methods, and systems that can withstand extreme physical conditions, just to name a few. It will also take a level of systems integration never-before seen in the mining industry, complete with big data issues, sophisticated predecitve analytics and modeling efforts and cyber-security challenges.Moreover, increasingly complex environmental problems will require creative solutions. Addressing issues like pollution control across multiple media, emerging contaminants, optimal management of wastes, selective mining and shared use of resources between mine operations and surrounding communities and ecosystems are among the top priorities. Really, a complete paradigm shift must occur, such that the focus is on overall improvement of environmental conditions, rather than minimization of impacts. A similar shift will be required in the social realm. How can miners be safer and healthier on-site and off? How can the industry contribute to communities such that they are better off, now and longterm, for having a mine next door? How can artisanal mining practices be transformed to also contribute to sustainable development? How can the industry’s work be a factor in increasing economic and political stability? How can the public understanding of raw resources and the need for mining enterprises be improved?Given the coming challenges, there is no doubt that the mine engineers of the future will need highly diverse skillsets — meshing traditional and contemporary competencies to a degree not previously considered in mining, or most others fields. To be sure, the scope and scale of mining projects make them wholly different than most other engineering work, aside from perhaps the largest civil and urban development projects. While on-the-job experience will continue to be essential, formal education programs (i.e., at post-secondary institutions) must lay critical groundwork."

Jan 6, 2017

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 meters (8 feet) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting and saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can effectively prevent solution flow through large portions of the stockpile, implying that great care must be taken to ensure that ripping is carried out to a full depth of at least 2.4 meters (8 feet) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2000

By David A. Smith

A new generation of reliable, stable, and easy to use bulk emulsions allowing application in tunneling and drift rounds has been developed. This new product group of bulk emulsions has been especially formulated for use in small-diameter holes and is a significant advancement in bulk emulsion technology. Reliable and easy-to-use bulk delivery equipment has been designed and developed to allow bulk emulsions to be used in a wide variety of shaft and tunneling applications.

Jan 1, 1987

By Earl Rau

Introduction Will cogeneration be a major power source in the future? The location of electric power generating plants has changed. In 1900, more than 50% of electricity was generated by industrial plants. Since then, industrial plant generation of electricity greatly decreased to 17% in 1950 and to only 3% in 1980. Changing economics in electric power generating costs, though, may allow cogeneration to reverse this trend. Cogeneration has been defined as the simultaneous production of electric (mechanical) and thermal energy from a single energy source. Some applications are considered to be byproduct generation of electricity from industrial, thermal operations. Cogeneration is not new to the mining and minerals industry. Smelters and steel mills have used waste heat to generate electricity. Public Utilities Regulatory Policies Act of 1978 The potential for increased industrial cogeneration of electricity is related to the March 9, 1978 enactment of the Public Utility Regulatory Policies Act (PURPA). The US Supreme Court ruled that PURPA is constitutional. The court upheld requirements that utilities interconnect to cogenerators. It also ruled that 100% of avoided costs be used as the guideline for electricity sales by a qualifying facility (QF) to a utility. The state of New York established a floor price $0.06/kWh for electricity sales from a QF to a utility. It is obvious, then, that a cogenerator must first establish price and then become a qualifying facility in order to sell electricity to a utility. Proposed cogeneration plants The estimated industrial cogeneration potential for the years 1986 to 2000 is 9500 to 25,000 MW. Industries represented in this cogeneration estimate are pulp and paper, petroleum, chemicals, food, textiles, rubber, plastics, steel, lumber and wood, cement, glass, metal fabrication, and industrial parks. A cogeneration plant has been proposed for the Union Carbide chemical plant in Institute, WV. A steam turbine/generator would be installed to replace the pressure-reducing valve in the 2.7 MPa (400 psig) header. Scott Paper Co., Mobile, AL, proposed a cogeneration plant using a coal- and wood-fired boiler and a turbine/generator to produce process steam and electric power. A cogeneration system has been proposed for a large oil refining plant. A pulverized coal boiler would produce high-pressure steam to operate a turbine, generator. The exhaust steam from the turbine will go to the process and an existing turbine. Kansas City, MO's Armour meat-processing plant has proposed a cogeneration plant. This proposal is to use a natural gas or oil-fired, gas-driven turbine and a generator. The waste heat from the gas turbine would go to a heat recovery boiler for use as process heat. Dade County, FL is implementing a central energy system to supply electricity, air conditioning, and domestic hot water for five buildings in downtown Miami. The cogeneration system is to provide flexibility, to optimize fuel use efficiency while serving the variable thermal demands. Generation of electricity from municipal waste is not considered to be a cogeneration process but is covered by PURPA. Special considerations are provided for waste/electric power generation to encourage the development of these systems. ?

Jan 7, 1987

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011