Search Documents

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By E. H. Myrhaug, K. Aasly, T. Malvik

Six different types of quartz and quartzites used as raw materials by ferroalloy plants have been investigated with respect to their thermo mechanical properties. In order to investigate the effect of the thermal shock caused by the rapid heating of quartz when it enters the furnace, the following techniques have been used for both in situ investigations and investigations of pre-heated quartz: -Heating stage microscopy for in situ observation of heating effects. -Shock heating of quartz in an induction furnace An optical microscope-mounted heating stage was used for in situ observations of the microscopic effects of heating up to 1300 ºC. The effects of heating were observed at different temperature intervals in different samples. The main temperature intervals were below 573 ºC and above 1000 ºC. The cause of the observed effects is interpreted as fluid inclusion decrepitation for T<573 °C and structural implications (micro cracks, grain boundaries and remaining fluid inclusions) at T>1200 °C. Shock heating of the samples was carried out in an induction furnace to 1300 ºC for ten minutes. The effects of the heating were studied with different techniques such as direct observation during and directly after heating, optical microscopy and XRD. Combined transmitted and fluorescence light microscopy shows that the heated quartz show an opening of the grain boundaries and evenly distributed micro cracks that were not present in the unheated reference samples. In some of the heated samples, weak generation of cristobalite was detected by XRD.

Jan 1, 2007

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By T. Güyagüler, A. Güngör

Labour protection, that is prevention of occupational disease and reduction in the frequency of accident, has always been a matter of major concern of mining industry. Management and the government should promote and maintain high safety standards through some measures to reduce accident frequency and occupational disease. This can be achieved by using the science and technology for improving the working conditions, educating workers and managers about accidents and prevention techniques. The detailed analysis of an accident requires knowledge of many factors such as location, time, type, cost of accident, victim, nature of the injury, personal and environmental factors etc. that can be obtained from the standard coded accident report form. There is a need to prepare safety data in a common format to produce a common safety reporting system and ‘Occupational Health and Safety Management Tool’ is being designed to manage this by using database and Internet technology. Precautions should be taken according to results from database queries by providing comprehensive and accurate national data. To have an accident is unfortunate, however, to have an accident and learn nothing from it is unforgivable. Keywords: Occupational health and safety, Accident report form, Accident database, Occupational diseases and accidents, Safety reporting system.

Jan 1, 2003

By G. S. Maré

Tin plating operations are of a complex nature due to the many operational variables that need to be controlled in order to create a product of required quality. The work in this report lays the basics for the control of a halogen plating operation based on the DuPont tinplating set-up with regard to the chemical make-up of the plating solution, as well as operational variables such as temperature and current density. To evaluate these aspects of the process, a rotating cathode Hull-cell set-up was used. This allowed for a laboratory scale plating arrangement that simulates industry closely with regard to chemical and hydro-dynamic considerations. Typical industry accepted standards were obtained for the values of operational variables and a ?baseline? test was conducted employing these standards. All subsequent tests conducted were benchmarked against this baseline result. A large suite of results was obtained in which it was found that changes could be made to the industry accepted norm which would improve on the stability of the operation and therefore the quality of the final tin-plated product. Examples of these results are: an increase in stannous tin concentration, an increase in sodium chloride concentration and a slightly elevated plating temperature. In addition, conditions were found that must be avoided to prevent instability and poor product quality.

Jan 1, 2010

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By R. Trammell, O. Eterigho-Ikelegbe, S. O. Bada

In response to the enormous amounts of coal discard generated during coal mining and preparation, the development of an efficient and sustainable strategic use of this resource is essential. Furthermore, the rising urban population over the next decades is confronted with the depletion of quality raw materials for building components. To this end, this study reports new information on the morphology, water absorption, and flexural strength properties of ceramic composites produced from three different coal discards and polysiloxane pre-ceramic polymer (PCP) resin. In addition, test results relating to the continuous operating temperature, chemical resistance, and efflorescence potential of the composites are presented. The results show that the water absorption and flexural strength of the coal composites, up to 1.94% and 36.46 MPa respectively, exceed the requirements for ceramic and clay roof tiles. The continuous operating temperature of composites is found to be more thermally stable than conventional roofing tiles (concrete and ceramic) between ambient temperature and 600°C. In addition, the excellent chemical resistance of the composites (94.43%−99.98%) compared to conventional roofing tiles (67.82%−99.97%) eliminates the need for additional external coatings. The interesting results documented so far suggest that this technique could be used to produce low-temperature application building products such as bricks, panels, roofing tiles, etc. This new recycling technique offers an excellent opportunity to eliminate enormous volumes of coal discard and to advance the circular economy in the coal industry.

Aug 2, 2022

By Reginald N. Boryor, Steven D. Woods

1.0 Introduction ?Low grade, high tonnage, open pit gold mine. ?Gold bearing Tarkwaian conglomerates. ?Reverse Circulation percussion drilling (25m X 25m grid). ?Composite 1m intervals, logged and split in the field to provide±2Kg samples. ?Samples used to build grade control block models using SURPAC. ?Approximately 100,000-130,000 meters drilled per year. ?RC samples are assayed using Rapid Cyanide Leach (RCL). ?Check assays are done using Fire Assay

Jan 1, 2005

By S. J. Oosthuizen

This paper examines innovation in relation to the availability of anew material: the metal titanium. The paper aims to highlight the need for the inclusion of entrepreneurial innovation as a necessary focus area in the development of a titanium metal value chain. Both the Department of Science and Technology (DST) and the Department of Mineral Resources (DMR) have identified the creation of titanium metals production capabilities as a key growth area for South Africa. Using historical literature as a source of data, the activities of selected innovators who used titanium metal as a central component in their success, were investigated. The origin of the process innovation behind the titanium metals industry, and two titanium product innovations: namely, medical implants and sporting goods, were detailed as case studies. It was found that individual innovators were responsible for the creation, and rapid growth, of the titanium industry and titanium product applications. There is a need to link the current research and development into titanium metals production with individuals and organizations capable of commercializing innovative processes and products.

Jan 1, 2011

By R. Nyirenda, B. Besa, N. Dzimunya

The accurate estimation of peak particle velocity (PPV) is crucial during the design of bench blasting operations in open pit mines, since the vibrations caused by blasting can significantly affect the integrity of nearby buildings and other structures. Conventional models used to predict blast-induced vibrations are not capable of capturing nonlinear relationships between the different blasting-related parameters. Soft computing techniques, i.e., techniques that are founded on the principles of artificial intelligence, effectively model these complexities. In this paper, we use the random forest (RF) algorithm to develop a model to predict blast-induced ground vibrations from bench blasting using 48 data records. The model was trained and tested using WEKA datamining software. To build this model, a feature selection process using several combinations of Attribute Evaluators and Search Methods under the WEKA Select Attributes tab was performed. The correlation coefficient of the actual data and RF model-predicted data was 0.95, and the weighted average of the relative absolute error (RAE) was 10.9%. The RF model performance was also compared to the equivalent-path-based (EPB) equation on the testing data-set, and it was seen that the RF model can effectively be used to predict PPV. The study also demonstrates that the EPB equation is a suitable empirical method for predicting PPV.

Mar 30, 2023

By M. Steyn

[Zr(C9H6NO)4]?(HCON(CH3)2)?(H2O), where (C9H6NO) = 8-hydroxy quinoline (oxH), was synthesized and characterized. This tetrakis-coordinated zirconium complex crystallized in the triclinic crystal system (Pi, Z=2) along with water and N,N?-dimethylformamide(DMF) solvate in the asymmetric unit. The metal atom is surrounded by four N,O-donating bidentate ox-ligands that are arranged around the metal centre to give a square antiprismatic coordination polyhedron with a small distortion towards a dodecahedral geometry. Crystal packing is stabilized by intermolecular interactions of adjacent oxine ring systems in neighbouring molecules, as well as hydrogen bonding of the aqua and DMF solvate molecules, linking the molecular entities into a supramolecular three-dimensional network.

Jan 1, 2013

By C. Dauber

Implementing new technologies in industrial operations entails the challenge of measuring the improvements gained by the applied technology. Nevertheless, it is absolutely essential to assess the technical and economic benefits in objective and comprehensible numbers to create a platform for further management decisions. Underground coal mines are characterized by numerous, quite complex procedures which make it difficult to determine the specific economic benefit of a new machine, technique, or method. In the OPTI-MINE Project funded by the European Union?s RFCS programme, five underground coal mines applied the latest information and communication technologies (ICTs) to improve efficiency, mine safety, occupational health, and environmental im-pacts. An integral part of the project is the assessment of these technologies by using key performance indicators (KPIs). The paper will describe some examples of the selected KPIs and the preliminary findings.

Jan 1, 2014

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By R Kroukamp

Horizontal belt filters are typically used for separation of relatively free filtering solids where good post treatment is required. He horizontal belt filter is a continuous filter with an endless cloth supported on a grooved carrier belt. The belt and cloth are driven around two rollers across a series of evacuated suction boxes. The feed suspension is introduced at one end of the filter and deliquored to produce a cake at the other end. The benefits of using horizontal belt filters are good cake washing, continuous and visible processing, fully automatic operation, flexibility, high capacity and relative high speeds of operation. If required, horizontal belt filters enable efficient counter-current washings to minimize the usage of wash liquid. The horizontal belt filter has applications in the following: [? Metal concentrates ? Mineral sands ? Tailings ? Coal ? Iron ore ? Alumina ? Chloride processing ? Nickel and Cobalt refining ? Platinum group metals ? Zinc processing ? Many other applications in the Mining and Metallurgy industries ] 2. Operating Principle of a Horizontal Vacuum Belt Filter 2.1 Cake Forming The slurry to be dewatered is evenly distributed onto the filtering surface. Gravity assists the cake formation and the feed can be introduced in multiple stages. 2.2 Cake Washing Once the cake is formed, wash liquor/water can be introduced onto the top of the cake via a wash launder or sprays. Multiple wash stages, co-current, counter-current or direct washing can be added by increasing the length of the filter.

Jan 1, 2007

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

The newly implemented mineral law framework exacerbated the need to clarify the roles and responsibilities of mine and land surveyors in the preparation and registration of plans and diagrams. The main concern is that survey tasks may be performed by persons who are not considered competent under the different laws. The methodology used was to analyse historic and present legislation on the issue in order to formulate a narrow interpretation of the current requirements. The major findings are tabulated to present a summary of who is responsible for which areas of survey.

Jan 1, 2010

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from &apos;difficult&apos; feedstocks.

Jan 1, 2006

By C. N. Harman, N. S. S. Rama Rao

Production of Ferro-alloys through submerged electric arc furnace involves use of electric power as one of the major inputs. Hence the production by this power intensive process can be made economically more competitive if the specific power requirement for smelting each ton of the product is brought down. This becomes all the more necessary where the power cost is comparatively high, like in India. Since the day FACOR started production of Ferro Chrome in 1968, briquetted chromite fines along with lumpy ores were used as feed. Subsequently the increase in the proportion of briquettes and reduction in lumpy ore helped in increasing the use of chromite fines and also brought down the specific power requirement. Meantime FACOR had been closely watching the technical development of use of sintered pellets in Outokumpu and SRC Processes which need still lower specific power. But the high capital requirement for a pelletisation plant kept FACOR from introducing pellets feed to their Ferro chrome furnaces. So this was postponed to be adopted in future. In February 2004 in the ?1st Ferro-Alloys India?, a paper [1] was presented by Dr. Amit Chatterjee. In the questions period after the presentation of the paper there came up a discussion in which it was revealed that with the Indian high grade chrome ores it was not possible to make sufficiently strong pellets, unless a larger percentage of bentonite is used as binder. This is because the Indian high grade Chrome ores have different mineralogy of gangue content compared to low grade ores in Finland and South Africa. Higher usage of bentonite gives rise to higher slag volume and this would result in increased specific power. Since FACOR had plans to go in future for sintered pellets feed, this gave rise to a doubt on success of pelletisation for Indian high-grade chrome ores. This prompted FACOR to take up experimental production of sintered chromite pellets and use of the same in one of their existing furnaces for production of high carbon Ferro chrome. The results are encouraging and are summarized in the paper.

Jan 1, 2007

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005