Search Documents

A dual rate kinetic model consisting of differential equations is used to describe the kinetics of the adsorption of gold cyanide on activated carbon. The partial differential equation describing the material balance in the liquid phase is written for the special case of a fixed bed system. It is shown that an isotherm for the case of a closed system is required to yield accurate simulations of the equilibrium in a column of activated carbon. Whereas the equilibrium loading of gold cyanide is influenced by the free access of oxygen to the system, the traditional open batch stirred tank experiments, which are used to estimate parameters for the calculation of breakthrough curves for organic solutes, cannot be used here. The program solves this model at incremental heights in the column at a specific future point in time. Runge-Kutta and backwards- difference methods are used in the numerical solution. A Von Neumann method is used to show that the solution is stable. Kinetic parameters can be estimated either from batch experiments or from short column runs. In the latter method the column should not be long enough to contain the concentration wavefront for the system of interest. Results obtained from bench scale continuous column experiments were used to verify the computer model. Pure gold solutions as well as real leach liquor were used in both short column and countercurrent moving bed experiments.

Jan 1, 1987

A large body of work exists discussing the impact of grinding media on mineral flotation. Generally, the work indicates that a change to a less electrochemically active grinding environment has positive benefits on downstream processing. There is a fear, however, that these benefits may not be realized when treating low sulphide containing ores, typified by UG2 style deposits. A series of experiments was developed to test the flotation response of UG2 ores using the Magotteaux Mill® to determine if measurable differences in the pulp chemistry could be discerned using a range of grinding media types. Further, the flotation responses of the contained sulphides (chalcopyrite, pentlandite and pyrrhotite) were determined. The data collected provided strong evidence that the grinding environment can significantly influence the pulp chemistry and flotation characteristics of all sulphide minerals, even when the ore contains less than 0.5 per cent total sulphide. The results show that the change to an inert media type produced a substantial improvement in the flotation rate of all sulphide minerals, as well as the PGMs.

Jan 1, 2009

By R. Kosmicki

Wet end components of centrifugal slurry pumps used in the hydraulic transport of solids are subject to substantial erosive wear. Accurate prediction of the casing wear rate and location for a particular duty is beneficial for correct pump selection and design, maintenance planning, and elimination of emergency shutdowns. CFD multiphase simulation using the Eulerian-Eulerian approach is being applied successfully to determine the velocity fields and solids concentration in the centrifugal pump, allowing for accurate predictions of casing wear patterns resulting from sliding abrasive wear. Simulation results for various single domain and multi-domain (multistage) multiphase simulations are discussed. Emphasis is placed on results from a 3-dimensional, multi-stage transient, multiphase simulation and comparison to field data.

Jan 1, 2007

By V. Léveillé

As new legislation drives metallurgical plants to lower SO2 emissions, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost-effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an a mine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 by-product stream, which can then be directed to the front end of a sulphuric acid plant for conversion to sulphuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulphuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature, SO2 emissions in the treated gas can be controlled to as low as 55mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System, as well as which features and cost advantages for the treatment of smelter gases were important in the technology choice.

Jan 1, 2009

By P. J. Kinver

This paper deals with the development of backfilling methods and systems at the Broken Hill orebody of Black Mountain Mineral Development Company (Pty) Limited, at Aggeneys in the north-western Cape Province. Production started in 1979, being confined to large diameter blasthole stoping methods in the upper, steeply dipping areas of the orebody. This blasthole reserve is now depleted and the production tonnage, 100000 tons per month, is produced from eight cut and fill stopes in the flatter dipping areas of the orebody. The fill methods of the blasthole stoping area evolved prior to the pillar extraction are briefly discussed together with the resulting experiences gained that enabled virtually 100% extraction to be achieved. The original cut and fill mining used costly hydraulic cemented fill; this was replaced partly by unconsolidated river sand and later by dune sand which occurs in abundance. The paper describes the planning, research work and commissioning of a cycloning plant that now enables dune sand to be used successfully as an unconsolidated hydraulic fill. The development of drainage, placement and control methods are also reviewed.

Jan 1, 1988

By D. A. Vetter

A novel mathematical model is presented which describes the behaviour of beds of particles, of uniform size and shape but different densities, during autogenous separations. The approach used in the formulation of the dispersion model is a phenomenological one based on a statistical view, which leads to a diffusion-like representation of the autogenous-separation process. Although the model currently considers only density-related phenomena, it accounts quantitatively not only for the density-segregation aspects of the process but for the interactions between the particles. Quantitative predictions of the dispersion model are compared with the results obtained in tests using a specially constructed experimental batch jig, and it is shown that the model provides an adequate quantitative description of the process for particles of uniform size and shape. It is pointed out that, for the description of more complicated autogenous separations, a more rigorous formulation of the particle drag and density-segregation terms will have to be incorporated into the dispersion model. Nonetheless it is concluded that the model as presented in this paper provides not only a novel insight into the mechanisms of autogenous separations but a means by which to analyse similar systems.

Jan 1, 1987

By C. Holck, J. Yarmuch, J. Read

"Steepening of slopes provides the means to reduce waste extraction and increase ore recovery in open pit mines; however, it may also adversely affect safety by posing a higher risk of slope failure. The implementation of slope monitoring programmes is recommended to manage this risk inherent in steeper slopes. In this paper, the design and evaluation of monitoring campaigns to measure subsurface deformation and groundwater pore pressure in open pit mines is presented. The monitoring programmes were applied to a theoretical case of an open pit mine designed using DeepMine software (BOAMine SpA, 2015). Mine plans were developed based on the initial base case scenario with monitoring programmes considered for four types of monitoring instrumentation: two established technologies, in-place inclinometers (IPIs) and vibrating wire piezometers (VWPs); one emerging technology, the ShapeAccelArray (SAA); and a novel technology under development, the Enhanced Networked Smart Markers (ENSMs). Technical and economic appraisals of the monitoring programmes and sensitivity analysis of the developed mine plans showed that using ENSMs spaced every 4 m had the lowest cost per unit of data gathered. IntroductionSeveral open pit mines have already exceeded their design life and, as they become deeper and reach depths over 1000 m, they face higher rock stress levels and tensile deformations (Stacey and Xianbin, 2004; Stacey et al., 2003). The more complex the conditions in modern open pit mines, the more difficult it is to achieve long-lasting, stable pit slopes and to meet the mine’s economic needs: maximize financial returns, minimize risks to operational safety, achieve optimal ore recovery, and minimize waste extraction (Stacey, 2009). Steepening of slopes provides the means to reduce waste extraction and increase ore recovery (Stacey, 2009; Calderon and Tapia, 2006; Bye and Bell, 2001; Jefferies, Lorig, and Alvarez, 2008); however, it may adversely affect operational safety, as steeper slopes are less stable than shallow slopes (Steffen et al., 2008; Mphathiwa and Cawood, 2014)."

Nov 1, 2018

By T. J. Otto, C. Musingwini

"The objective of any mining company is to sustainably maximize the net present value (NPV) throughout the life-of-mine (LOM). The expected NPV over the LOM is calculated based on a mine plan, yet the actual value realized by the mining company depends greatly on the level of intertemporal execution against the mine plan. Consequently, a major key performance indicator (KPI) that is often overlooked in open pit mining, due to a greater focus on temporal KPIs, is the degree of spatial compliance to the mine plan. Such focus sometimes leads to short-term actions being detrimental to long-term plans. In this paper we describe the development and implementation of a spatial mine-to-plan compliance reconciliation approach for an open pit mine. Application to a case study open pit iron ore mine in South Africa indicated a significant improvement in the spatial mine-to-plan compliance, from 69% to 94% over a three-year period from 2014 to 2016. These results indicate that implementation of the proposed spatial mine-to-plan compliance reconciliation approach can contribute positively to improving the level of spatial execution and assists in improving the alignment between short-term, medium-term, and LOM plans.IntroductionThe objective of any mining company is to maximize the net present value (NPV) throughout the life of mine (LOM). However, this objective needs to be fulfilled in a sustainable manner that considers the needs of various stakeholders, including employees, shareholders, and local communities where the mines operate. The expected NPV is calculated using a mine plan as a basis. Mine planning broadly involves identifying a strategy to exploit the mineral resource in a way that maximizes value at an acceptable level of risk throughout the LOM (Tholana and Neingo, 2016).The mine planning process is a well-recognized component in the mining value chain of an open pit mine. Figure 1 reflects the relative position of mine planning within a typical open-pit mining value chain from the mineral resource to the market"

Mar 1, 2019

By Q. G. Reynolds

The dual-electrode direct current (DC) arc furnace uses two graphite electrodes, one connected as cathode and one as anode. Such an arrangement avoids some of the design difficulties associated with the anode hearth traditionally used in single-electrode and twin-cathode DC furnaces, but can introduce other design and operational difficulties including deflection of the arcs toward the furnace walls. Counter-intuitively, both arc jets in a dual-electrode furnace travel from the electrode down to the bath surface, despite carrying electric current in opposite directions?this is suggested in the theory of the governing equations of arc formation, and confirmed by experiments using high-speed photography. The dual-electrode arc system at small pilot-plant scale is studied using a transient magnetohydrodynamic model capable of predicting arc deflection and interaction from first principles, and the results are compared to the behaviour of twin-cathode systems at similar power. Finally, a simple arrangement of the furnace busbars, M configuration, is shown to provide some passive protection against arc deflection.

Jan 1, 2011

By J. W. van der Merwe, C Strydom, D. C. Odendaal, M. I. Sampson

Keywords: Sphalerite, Bio leaching, Chemical leaching Sphalerite concentrates were prepared from tailings dam samples obtained from Rosh Pinah Mine in Namibia. The samples were subjected to froth flotation and concentrates containing between 7% and 14% Zn were prepared. Leaching of these froth flotation concentrates were studied in ferric chloride solutions at different Fe3+ concentrations for different times at different temperatures with the influence of other species on the kinetics in mind. Complementary to this research, GeoBiotics, LLC and Exxaro Resources have developed proprietary bioleaching technology for the oxidation of base metals concentrates using GEOCOAT bio heap leaching technology in a sulphate medium. The ferric chloride laboratory work was performed in a fluidising leach reactor. The studied material was obtained from flotation concentrate produced during an investigation into the recoverability of a tailings pile at Rosh Pinah mine in Namibia. The optimum conditions for the laboratory investigation were found to be a Fe3+ concentration of 0.3 mol/dm3 at 80°C. A control was performed by using synthetic zinc sulphide. GEOCOAT evaluation tests are performed for the purpose of evaluating the bioleaching of ore and flotation concentrates by means of mesophilic bacteria, Column tests were carried out on the flotation scavenger concentrate from Rosh Pinah to assess the application of the GEOCOAT® process for the oxidation of a low grade zinc concentrate. In this study an attempt was made to demonstrate the relationship between the Kinetic models and the experimental data by plotting the fraction of Zinc leached against time and applying the different equations to the data. The kinetic models were applied to the data obtained from both the test regimes. Habashi (1999) proposed that if a process is controlled by a chemical reaction at the interface (phase boundary controlled reaction), the following equation applies. kCt =1 ? (1-R) 1/3 Alternatively a process is controlled by diffusion through the product layer the following equation applies: [kt = 1 23- X (1 ? X) 2/3] As the anodic dissolution reaction progresses, reaction product forms either a more or less dense reaction product layer on surface As this product layer forms, a diffusion problem develops governed by the nature of the product layer. The conclusion from the study was that the kinetics is very dependent on the type of ore processed relating to the mineral composition of the ore body.

Jan 1, 2007

By J. T. M. Amphlett, C. A. Sharrad, M. D. Ogden, R. I. Foster

"A renewed interest in nuclear power around the world in order to reduce greenhouse gas emissions is going to increase demand for uranium as fuel. This will result in more uranium being mined, which will in turn increase associated environmental pressures, such as fresh water use. A move to lower quality waters containing impurities such as chloride would help alleviate these pressures. In this work, we determined the uptake characteristics of weakly basic anion exchange resin Ps-EDA towards uranium from saline solutions in a dynamic flow column. Breakthrough curves were produced, with suppression of uptake being observed for chloride concentrations above 5 g L-1. Calculated resin saturation capacities at zero and 5 g L-1 chloride are comparable with literature values for strong-base anion exchange resins, and exceed those published for weak-base resins up to 20 g L-1 chloride. Data has been fitted to multiple breakthrough models, with the modified dose-response model most effectively predicting uranium recovery. The results show that the ethylenediamine functionality could be suitable for use in future uranium processing flow sheets where a high-saline lixiviant is used. IntroductionIon exchange (IX) is a key technology in the uranium mining industry and is well established for the extraction of uranium from both acidic and alkaline leach liquors (Edwards and Oliver, 2000). It was first employed in 1952 at the West Rand mine in South Africa (Ford, 1993; Taylor, 2016). H2SO4 and Na2CO3 are the most commonly employed lixiviants used to solubilize uranium in acidic and alkaline leach conditions respectively. The chemistry of these systems causes uranium to form anionic sulphate or carbonate complexes, which can be taken advantage of by anion exchange resins.Another major technology for the extraction and purification of uranium from leach liquors is solvent extraction (SX). This technique involves the extraction of uranium from the aqueous phase into an immiscible organic layer. Although this is a commonly used method, there are major drawbacks to it, including the use of large volumes of flammable solvents, solvent loss, phase disengagement, third phase formation, and the production of problematic degradation products (Veliscek-Carolan, 2016). These problems can be circumvented through the use of IX resins."

Dec 1, 2018

By P. Goosen

The paper presents a basic summary of the approach to hydraulic scale-model tests as may typically be applicable to slurry flow situations. A case study is presented illustrating how hydraulic scale-model tests can be of significant benefit in evaluating the performance of novel or unproven slurry handling equipment. In this case the equipment tested was a fan-shaped expansion piece used to spread the discharge from a launder over the full width of a dewatering screen. The tests showed that the device did indeed distribute the slurry flow both in terms of volume and solids mass, but not perfectly uniformly. Unfortunately the equipment was not taken beyond the model test phase. The scale-model test approach did, however, prove to be very useful as it is considered to have provided a good indication of the expected performance of the full-size unit. Significantly, this was achieved at very low cost compared to the cost of installing the device into the proposed plant and having to later change it out for an alternative or live with the less than optimal performance. The paper illustrates the value that can derive from applying hydraulic scale-model testing techniques to evaluating the performance of new or unusual slurry handling equipment. There is particular value in situations that do not lend themselves to numerical modelling.

Jan 1, 2007

By A. O. Filmer

In the mining and metals industry, business strategy demands that leaders extract more from any set of capital assets. This improvement is achieved through a combination of continuous improvement and upgrading of the assets. Continuous Improvement involves a series of incremental changes in the workplace to stabilize the process, remove waste, and test the limits of process capability. Enhanced Technology involves the replacement of an existing as set with a different process or equipment, to achieve a similar function in a more efficient and effective manner. The paper compares and contrasts the two methodologies and outlines the key business considerations which dictate how and when to select one or other improvement method. The paper also addresses the implications for these two improvement methods for those undertaking R&D in support of the mining and metals business.

Jan 1, 2009

High pressure grinding roll (HPGR) technology is used in an increasingly diverse range of applications, predominantly iron ore , gold and diamonds. KHD Humboldt Wedag HPGRs are applied world-wide, and consistently prove to be well designed and reliable operating units, with their performance meeting the pre-set standards. This publication summarizes some of the features and experiences for recent applications in treatment of copper ore, coarse iron ore, and gold ore. Summary data of roll surface wear life and operating data are given, together with operational observations. In addition, effects of feed segregation and truncated feed are discussed, as well as the implications of a product recycle flow sheet.

Jan 1, 2012

By R. Haldenwang, R. Erasmus, P. T. Slatter, R. P. Chhabra

Notches are used routinely for measuring the flow rate of water with free surface flows. As far as can be ascertained, no work has been done to investigate the performance of these flow rate measurement devices for non-Newtonian suspensions. The Flow Process Research Centre at the Cape Peninsula University of Technology has investigated the flow rate of kaolin and bentonite suspensions from a tank for two notch shapes, namely rectangular and triangular, and for 3 different concentrations of each suspension. The notches were calibrated using water and then the kaolin and bentonite suspensions were tested in them. The rheological characterisation of the fluids was done with a Paar Physica MC-1 rotary viscometer fitted with a cup and roughened bob. Analysis of the results shows a significant increase in discharge coefficient with increase in concentration, and the discharge coefficient has been correlated to the yield stress. This is the first such study, and further investigation is needed to confirm and extend these findings.

Jan 1, 2007

By F. A. G. M. Camisani-Calzolari

The uranium production forecasting program described in this paper projects production from Reasonably Assured, Estimated Additional and Speculative Resources in the cost categories of less than $130/kg U. Originally designed to handle South African production, it has been expanded and redimensioned using available published information to forecast production for countries of the Western World. The program forecasts production from up to 400 plants over a period of fifty years and has built-in production models derived from documented historical data of the more important uranium provinces. It is particularly suitable to assess production cavabilities on a national and global scale where variations in outputs for the individual plants tend to even out. The program is aimed at putting the uranium potential of any one country into a realistic perspective, and it could thus be useful for planning purposes and marketing strategies.

Jan 1, 1987

By D. T. Jordan, L. C. Coetzee, G. Kalenga, T. Mahlangu, W. J. Shipman

Although online free cyanide analysers are widely available and used in gold leaching operations worldwide, reliable automated free cyanide concentration control is not consistently achieved in many of these operations. Effective cyanide concentration control is complex owing to amongst others, the long residence times and ore feed variations. Model Predictive Control (MPC) has been proven to provide superior cyanide concentration control over traditional proportional-integral-derivative (PID) control, leading to savings in operational costs and reduced leachable gold losses. In the first example reported in this paper, MPC has improved control of the free cyanide concentration by keeping it within the required range 73% of the time during testing, compared to the previous PID controller that only achieved this target 30% of the time. This represents a 143% improvement. Another example demonstrates a 22% reduction in cyanide usage as a result of using MPC. MPC functionality is rarely available on the programmable logic controllers (PLCs) and control systems installed at gold plants, hence it is implemented on a personal computer (PC) networked to the cyanide analyser and plant infrastructure. Mintek has developed an embedded MPC that installs into the Mintek Cynoprobe analyser, adding MPC functionality without the need for additional PC and network infrastructure, reducing installation costs. This allows plants to minimise their expenditure on additional infrastructure while gaining the benefits of superior MPC technology for multiple cyanide dosage points. This paper will present results showing that the embedded MPC performs as well as Mintek’s existing PC-based StarCS MPC controller, making it a viable alternative for infrastructure-constrained gold plants. Keywords: Model predictive control, gold cyanidation

Jan 1, 2020

By H. Rosenberg

Haldor Topsoe A/S has developed its WSA technology to meet the demand in the market for a simple and reliable process that converts sulphurous emissions from off-gasses into high-grade sulphuric acid. With more than 50 references in 25 countries, the WSA technology has proven its ability to generate acid at 98% concentration, efficiently and economically. The wet gas sulphuric acid (WSA) technology treats the furnace off-gas directly from upstream gas cleaning plants. No further drying is required, since the humidity present in the off-gas is used to hydrate the SO3generated in the converter and produce sulphuric acid. The heat generated during the oxidation, hydration and condensation processes is principally reused in the process to preheat the off-gas to the required temperature level, and also to generate high pressure superheated steam for process use. This advantage of steam production, coupled with lower water and power consumption requirements, is particularly important in the African production environment. Having fewer process components than conventional acid plants, the WSA technology is a simple and compact operation, which makes it easier to retrofit into an existing smelter plant. Further, the WSA technology simultaneously offers the possibility to treat multiple gas streams arising within the production facility due to superior flexibility in terms of SO2concentration and turndown ratio.

Jan 1, 2006

By M. Nakamura, T. Akamatsu

Embankment dams are often constructed on soft rock foundations in Japan, so it is important to precisely predict deformation of the foundations due to fill placement at the design stage. In order to accurately evaluate the settlement and the strain of the rock foundation surface during construction, the influence of the scattering of the deformability of foundations on the deformation behaviour should be investigated. In this paper, a method of evaluating the settlement and the strain of the rock foundation surface during construction was studied with stochastic deformation analysis considering the scattering of the deformability of the dam foundation. Based on the analytical results, a dam foundation design using the deterministic method considering the scattering of its deformability was discussed. Da in Japan Uferdämme of auf weichen Felsfundamenten gebaut werden, ist es wichtig, die Verformung der Fundamente auf Grund der Platzierung der Aufschüttungen bereits in der Planungsphase genau vorherzusagen. Im Zusammenhang mit einer genauen Beurteilung der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten sollte auch der Einfluss der Streuung der Verformbarkeit der Fundamente auf das Verformverhalten untersucht werden. In der vorliegenden Studie wurde die Bewertungsmethode zur der Senkung sowie der Belastung der Felsfundamentoberfläche während der Bauarbeiten mit Hilfe von Wahrscheinlichkeitsanalysen der Verformung unter besonderer Berücksichtigung der Streuung der Verformbarkeit der Dammfundamente untersucht. An Hand dieser analystischen Ergebnisse wurde das Design der Dammfundamente dann enthusiastisch mittels deterministischer Methoden hinsichtlich der Streuung der Verformbarkeit diskutiert. Comme les barrages en remblai sont souvent construits sur des fondations rocheuses tendres au Japon, il est essentiel de prévoir précisément les déformations des fondations causées par la mise en place du remblayage durant la phase de conception. Afin d’évaluer avec exactitude le tassement et la déformation de la surface du rocher de fondation durant la construction, l’effet de la dispersion de la déformabilité des fondations sur le comportement de déformation doit être étudié. Dans cette étude, l’auteur a étudié la méthode d’évaluation du tassement et de la déformation de la surface du rocher de fondation durant la construction en procédant à une analyse aléatoire/stochastique de la déformation et en prenant en considération la dispersion de la déformation des fondations du barrage. En se basant sur les résultats de l’analyse, la conception des fondations de barrage avec la méthode déterministe considérant la dispersion de sa déformabilité a été activement discutée.

Jan 1, 2003

By J. T. Nel

The Kroll process is the traditional method of producing zirconium metal by reduction of zirconium tetrachloride with magnesium metal. This paper discusses the production of zirconium metal in a plasma reactor. Anhydrous low-hafnium ZrCl4 and Mg metal were fed continuously to a 30 kW non-transfer plasma reactor at a rate of 0.31 kg.h-1. Due to losses in the system the recovery of crude product was 77.5 %. After purification to remove unreacted feed material and MgCl2 by leaching, >98 % pure zirconium metal powder was obtained. The overall recovery of purified Zr was 74 %. The conversion efficiency of the process was 95 %.

Jan 1, 2012