Search Documents

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By J Lyall Workman, Larry R. Fletcher

Blasting methods have been proposed for reclaiming abandoned underground coal mine sites having unstable conditions. The objective of blasting is twofold: the permanent stabilization of an area by the collapse of underground workings to prevent any future subsidence, and the use of blasting to close existing sinkholes.

Jan 1, 1991

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By W. J. Birch, R. Farnfield

Nuisance caused by perceived high vibration levels as a result of blasting on quarries and opencast coal mine is now the number one environmental concern of residents living adjacent to such operations. The intrinsic nature of blast vibration monitoring and prediction is that it is impossible to accurately forecast the vibration levels that will be experienced by a given blast at a given location. Thus it is that a statistical approach to the problem is the only viable option. Unfortunately, persuading local residents living adjacent to a project that requires blasting that this is the best way of safe guarding both their homes and their quality of life is not an easy task. Thus routine monitoring involving both operators and regulators play a key role in building trust. However, public confidence is often shaken when regulators and operators use two different blast monitoring instruments side by side to record a blast at a local resident’s house and arrive at different results. To make certain that this does not happen in future, what is needed is a protocol that ensures that any two different blasting seismographs give the same peak particle velocity values at the same observation point. To do this all the equipment manufacturers, regulators and relevant professional explosive engineering bodies need to be involved.

Jan 1, 2014

By David Jones, Jeff Bregar, Damien Bell

We have analyzed overpressure and ground vibration measurements for construction blasting for a large pipeline project. These field-measured levels have been compared to existing prediction curves in the literature and new curves have been proposed for overpressure and ground vibration for pipeline construction blasting activities.

Feb 1, 2020

By Philemon Desrochers, Ken Qian Liu

Following the success of the West Ore Zone distress mass blast in 2001 at Brunswick Mine, a similar approach was taken to distress the North Regional Pillar (NRP) which contained over 3 million tonnes of high grade ore. The NRP is located on the 1000 m Level with very poor hanging-wall (H/W) rock mass qualities. After an extensive geotechnical review, the distress slot is located close to the foot-wall (F/W) of the NRP in order to have the competent ore as H/W. The longitudinal area to distress covers 115 m along the strike and 85 m high from 1000 1-sub to 850 Sill. Prior to the final mass blast, 3 voids were created to allow rock swelling: the North void, the South void and the trench just below the mass blast. After over one year of preparation, the mass blast of 202,000 tonnes was successfully initiated on February 7, 2003 with 1561 electronic detonators and 210,000 kg of emulsion explosives. The blast achieved its objective of distressing the NRP as indicated the mine-wide micro-seismic monitoring system. This paper describes different stages of the project from void preparation to the mass blast itself, as well as some detailed aspects such as muck-pile prediction for mucking sequence with the help of DMC_Blast simulation code and electronic detonators.

Jan 1, 2004

By Lyall Workman, P D. Katsabanis

Energy released by the explosive is typically partitioned in brisance, heave and losses. The fact that energy released in the P-V expansion curve below a certain point is lost has resulted in the concept of available energy. Through simple calculations it is shown that energy released at pressure levels thought to be low, amounts to a significant proportion of the total energy value. Furthermore, throw calculations indicate that the assumed loss of that part of energy does not justify practical results. Loss of energy at the low pressure levels may also not be justified from the fragmentation point of view as pressure levels below 1 kbar are enough to extend radial fractures around a borehole. Finally the equation used for the P-V behaviour of the explosive gases is important in throw calculations. Simplified approaches may not reproduce the performance of the explosive which is not characterized only by its energy content.

Jan 1, 1998

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By Alan B. Richards, Aleks Todoroski

The undesirable effects of blasting fumes can be controlled by minimising the amount of fume created, and by avoiding the movement of the fume plume to sensitive locations. Substantial progress has been made by the blasting industry to reduce the amount of fume typically created by blasting, but at this time no specific blast can be guaranteed to be ‘fume free’.

Jan 1, 2017

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Bilegt Batbold, Bayu Saputra, Chris Batten

The ability to fire multiple blasts simultaneously can provide significant benefits to any open pit mining operation. Reduced blast-related downtime by reducing blast events can increase equipment utilization and maximize material movement. Significant sequencing benefits can also be delivered, associated with reduced equipment relocation. This paper describes the work completed in partnership between Orica and Oyu Tolgoi to successfully demonstrate that combined production-trim and midsplit blasting could be implemented successfully while successfully managing the risk of increased damage to the final walls. The paper details the methodology used to assess key performance measures linked to final wall damage and compares the performance between the following blasting methods. • Free face trim blasting vs. combined production-trim blasting • Presplit blasting vs. midsplit blasting. The results of the initial trial blasts are presented, along with the method agreed by the key site stakeholders for ongoing application. The method used to keep the risk of final wall damage to an acceptable level is explained, along with the benefits delivered to Oyu Tolgoi operations associated with the initial 12 months of application.

Jan 21, 2025

By Tuan Nguyen, Dirk Hummel, Ruilin Yang

In a tunnelling site in Japan, it was found that detonators failed to initiate with their shells and primary explosive intact. Their capacitors, however, were discharged due to some damage on the application-specific integrated circuits (ASICs). These detonators are distinctly different from other commonly observed failures, where the shells are rather crashed due to excessive dynamic pressure received from neighbouring blastholes which fired earlier. Such incident has not been reported elsewhere. Detonator failures during a blast are deemed not safe and can cause disruption on the project productivity. It is therefore desirable to understand the origin of such event. Various measurements were conducted to diagnose the problem, but the root cause had yet to be identified. This paper applies a discovery from a 60-year-prior-laboratory experiment and formulates a theory that could explain the observed detonator failure and predicts the measurements and observations.

Feb 6, 2023

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By Italo Onederra, Gary Cavanough, Ewan Sellers

Reactivity of ammonium nitrate based explosives is associated with the presence of iron sulfides in the ground reacting with explosive products and in some instances causing spontaneous reactions which can lead to detonation. The stability of explosive products can also be linked to in-hole density, which influences detonation efficiency, breakage performance and the potential generation of Nitrogen Oxide (NOx) fumes. Reactive ground testing involves detecting a temperature rise of a mixture of a bulk explosive product sample, a ground rock sample and some specific chemical agents. This paper describes improvements in reactive ground testing involving the use of time lapse video analysis and detection of NOX gas emissions from the sample. Reactivity is stored and linked to a using cloud based software to map of the mine showing the exact location of the sample. The location marker can be selected to allow quick access to the sample test results and video. In addition to reactivity, the stability and detonation performance of bulk product can also be influenced by depth. In this paper, a system that simulates product at depth and measures density changes and monitors the structure of bulk samples is described. Results from an explosive product are analyzed and detonation performance is assessed by the measurement of velocity of detonation and detonation pressure.

Jan 1, 2018

By S. Klerkx, R Battulwar, J Valencia, J Sattarvand, E Emami, M. Soleymani Shishvan

A new technology for energy distribution optimization, supported by NIOSH.

Feb 1, 2020

By C. Zuniga, S. Combrinck, C. Peters

Agnico Eagle Gold have partnered with Enaex Australia at their Fosterville gold mine to leverage a combination of drill and blast technologies to optimise underground development mining. The mine is the first site globally to collaboratively develop and trial Enaex SWIFT electronic development detonators, which utilise a novel approach to the user interface, simplifying implementation and enabling the benefits of electronic initiation without the complexity of a conventional system. This has been combined with the use of a Sandvik 422i smart jumbo, and the Enaex underground emulsion charging unit with the capability to tailor the delivery of explosives as required and report on a hole-by-hole basis. The combination of these technologies enables full engineering oversight of the development cycle, in turn enabling optimisation of this process in a historically conservative application. The methodology for leveraging these technologies is to bore a controlled and defined blast pattern through using a smart jumbo, load the blast holes utilising lace loading to deliver a desired quantity of ammonium nitrate emulsion per hole, with the ability to reduce chargeweight for perimeter control, and utilising Enaex SWIFT electronic detonators with flexible template type pre-defined delays to initiate the blast holes. Subsequent to firing and excavation the performance of the blast in fragmentation, advance efficiency, and overbreak and underbreak is measured and reviewed. This is then used to optimise the development cycle and apply to other parts of the mine.

Feb 6, 2023

By A. S. Romphf, C. K. McKenzie

Recent full-scale field studies involving single-hole charges fired to free faces under a wide range of operating conditions have delivered precious insights into airblast characteristics and propagation. The field tests involved production blasthole diameters in the range 89 to 406 mm (3 ½ to 16 in), bench heights in the range 9 to 24 metres (30 to 79 ft), burden ratios (burden/hole diameter) in the range 14 to 51, stemming ratios (stem height/hole diameter) in the range 11 to 36, explosive types of ANFO, heavy ANFO and pumped emulsion, and both solid-column and double-decked charge configurations. Around 700 measurements of peak amplitude and wave shape were made in all directions (0 to 360 deg) from the free face, from 38 single-hole tests in nine North American operating quarry/mine environments. The most striking observations were the strong dependence on directionality of the wave propagation parameters and wave frequency, the consistency of wave shape which resembled the modified Heelan wavelet, and the occasional appearance of distinct, multiple pulses from single events, shown to be echoes/reflections from quarry faces. In-hole deck charging failed in this study to achieve expected peak overpressure reductions, with the peak overpressure levels in Pascals/psi/millibars being approximately 40% higher than the as-charged weights. Inter-deck delay times in excess of around 25 ms are required for effective reduction of peak overpressure levels from front-row holes. Simple linear-superposition models based on synthetic wavelets applied to large production blasts produce composite waveforms which capture the important features of the actual pressure-time history, and correlate well with measured waveforms.

Jan 26, 2026

By Stephen Mansfield, Nathan West, El Khalil Seyed

In October 2017, a multi-bench failure occurred in the east wall of the Guelb Moghrein copper and gold mine in Mauritania. The failure extended 100 m (328 ft) vertically and horizontally and resulted in the sterilisation of ore, but no equipment or personnel were put in danger. The remediation plan successfully removed the failed material and the cutback resumed to a modified pit design, leaving ore reserves behind. In 2021 after completion of mining in another part of the pit, a plan was formulated to develop a narrow cutback behind the failed wall and recover the sterilised ore. Infill drilling defined a resource of approximately 2.9 Mtonne (3.2 Mton) of ore at 0.78% Cu and 0.67 g/t Au at a strip ratio of 5.5:1. The high strip ratio meant that it was necessary to mine thirteen benches of waste, or 156 m (512 ft) vertically, over a two-year period before reaching the first ore, with the cutback only being economically viable if all ore could be depleted at the end of the third year. The high economic risk of the project required a holistic approach to mitigate the risk of another wall failure, by addressing the following areas: 1. Pit Design: with help from an external Geotechnical Consultant, the pit design was optimised to include increased factors of safety, reduced stress points, lower overall slope angles and straight lined walls were replaced with curved walls. 2. Geotechnical Management: the site Geotechnical Superintendent worked closely with an external Geotechnical Consultant to better understand the structural geology. Slope monitoring was improved through an expanded network of prisms, regular in field inspections and the use of a slope monitoring radar. 3. Drill and Blast: new drill and blast designs were developed from first principles, consisting of production, wall control and presplit designs. Blast master polygons and bench development sequences were developed with consideration of the structural geology and the influence of the initiation designs. 4. Mine Operations: improving operational discipline was a critical factor that ensured the accurate execution of drill and blast designs and excavation to bench levels and pit limits. This holistic approach has enabled the safe development of the cutback down to the 936 RL (relative level), two benches below the point at which the previous wall failure occurred. Extraction of ore has occurred from the 960 RL, and due to faster than planned excavation rates, the cutback is expected to be completed ahead of schedule.

Jan 21, 2025

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By Rob Farnfield, Ben Williams

The A5 road in the United Kingdom forms an ancient and well-used route through the hills and mountains of North Wales. In the 1990?s a programme of work was conducted to upgrade the road to modern standards. As part of this work a new cutting was constructed to bypass a portion of road routed through a gorge close to the village of Ty Nant. This new cutting was formed by drilling and blasting and included much pre-splitting and extensive rock bolting. This operation caused much concern to local residents relating to vibration, air overpressure and flyrock.

Jan 1, 2011