Search Documents

By Andrew Drake, Mark Burchard, Peter Bellairs

The Astec Bluerock Quarry is excavating an extremely difficult to blast rock type due to its highly variable jointing density that leads to excessive oversize. A drill and blast benchmarking exercise led to eight recommendations to minimise this problem. Quarry personnel instigated a continuous improvement blasting program, that has implemented six out of eight recommendations, resulting in a large reduction in the oversize and increased crusher throughputs for a marginal 7% increase in drill and blast costs. Unit costs have reduced by an estimated 10%.

Jan 1, 1998

By Agus Setiabudi

East Pit Wira II Project in South Kalimantan, Indonesia with a radius of <500 meters (1,640 ft) from residential has about 454,168 tonnes of coal reserves, with a total remaining reserves of 3,369,383 tonnes (topography per end of June 2011). Thus, reserves may be lost as much as 13.48%. Therefore, it is needed to determine safe blasting technique which meets the Indonesian National Standards (SNI) No. 7571:2012 of vibration threshold, the maximum vibration of 3 mm/s (0.118 in/s) and air blast of 120 dB.

Jan 1, 2014

By Calvin J. Konya

The Woodville Lime and Chemical Company Limestone Quarry is located in Sandusky County, Ohio. Fifty years ago, when quarrying began, it was situated approximately two miles from the town of Woodville. Today new houses border the quarry property within 1,500 feet of one of the working faces. During the past two years, the operation has systematically changed the blasting program to achieve better fragmentation, lower costs, and to maintain good relations with the local property owners. This paper will discuss systematic changes made in the blasting program to increase productivity and reduce costs.

Jan 1, 1977

By Robert L. Brooks

Blasting liability problems are frequently compounded by a company's inability to effectively communicate with concerned property owners and the lack of adequate complaint documentation. Often, by the time the insurance carrier becomes involved in a blasting claim, the situation has deteriorated to the point that a solution agreeable to both parties is virtually impossible to reach. The insurance carrier, wishing to minimize their lose potential may decide to pay on a somewhat questionable blasting claim rather than be drawn into lengthy civil proceedings that would ultimately end up in front of a jury with little chance for a successful outcome.

Jan 1, 1992

This paper examines the hypothesis that the fragment size distribution of blasted rock contains information about the changes in fragment sizes with distance from the borehole, and that this information can be interpreted and used to predict the effect of powder factor on fragmentation. A set of simple relationships between the fragment size distribution curve and the dependence of fragmentation on powder factor is proposed. The equations derived are compared with published data on fragmentation in small scale blasting. Two data sets were analyzed, and the results confirm the hypothesis.

Jan 1, 1997

By Virgil J. Stachura, Larry R. Fletcher, Paul V. Sterk, Matthew N. Plis

The large diameter blastholes now being used in underground mining have caused concern because of their increased potential for damaging openings and creating rockfall hazards. In response to this situation, the Bureau of Mines is conducting research to reduce the amount of overbreak and damage to the perimeter of underground openings. This paper presents the results of tests with decoupled charges in 6.5 inch diameter blastholes, and unloaded guide holes, in Vertical Crater Retreat (VCR) stope panels at the Homestake underground gold mine in Lead, SD.

Jan 1, 1991

By John Eloranta

This paper is a case study showing the assembly of available rock property parameters for the purpose of blast design. Blast optimization now includes subsequent milling and requires a full knowledge of the rock mass. Individual blast holes should be designed using all available data. The parameters include: geologic layer from diamond drilling, shovel performance, crushing plant experience from that area, drill monitoring, magnetic susceptibility from a downhole probe, size analysis history from digital image analysis, compressive strength tests of problem areas and cross hole sonic testing. Bedding thickness observed from drill core appear to have a strong influence on fragmentation.

Jan 1, 1996

By Glenn Ludwig, Stephen H. Chung

Fragmentation has a direct impact on mine costs and productivity. Computer programs have been developed to calculate fragmentation using data on the properties of the explosive, the characteristics of the rock, the rock mass and the blast pattern. While computer models can yield good data, conclusions must be verified. Fragmentation assessment, muckpile surveys or high speed film analysis of rock mass movement are some of the techniques that have been used to confirm blast results. Digitizing photos of the muckpile is now the most common method to assess fragmentation. But it has some drawbacks. Although automatic electronic imaging equipment speeds up the process, the results depend on the photographs. Shadows will distort results. High resolution, black-and-white prints are essential.

Jan 1, 1992

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Douglas Rudenko

When blasting complaints come, as an industry we often immediately look to the ground vibration as the source of the trouble. Often times we overlook or place less emphasis on the collected air overpressure data. Air blast like ground vibration is an undesirable side effect of blasting and can produce considerable structural response.

Jan 1, 2002

By Guillermo Silva

A novel, ultra-low density explosive composition, particularly suited for wall control and other applications requiring customising of the explosive’s energy output, has been developed. Being reactive in nature, the low density explosive enables the controlled dilution of dry blasting agents from their nominal densities down to values slightly less than 0.10 g/cm3. The product has been detonated at densities of 0.07 g/cm3 in diameters as small as 50mm under confined conditions, using a 227 g (l/2 lb.) primer. Recorded velocities of detonation ranged between 1200 m/set and 2200 m/set for densities between 0.07 and 0.2 g/cm3. Theoretical velocities ranged from 1700 m/s to 2500 m/s for the same density range. The low density explosive was insensitive to initiation by a blasting cap which is a desirable feature for transportation purposes. Mixing of the product with ANFO has been accomplished with minimum segregation making it suitable for applications where reduction of pressures are necessary.

Jan 1, 2000

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

By Dale Preece, Stephen Chung

The DMC-BLAST (Distinct Motion Code) has been developed for modeling bench blasting to one or two free faces such as choked blasting in surface gold operation and cast blasting in coal mining, respectively. This computer code has been used to assist the analysis of rock mass displacement after a blast was initiated in an orderly delay sequence. Applications of this feature can be found in the studies of dilution control in surface mining of gold as well as coal involving complex rock structures. Recently, DMC-BLAST has been modified to include a designated delay firing order coupled with variable rock strengths in the blasted media. This newly added feature allows the investigation of the effects of delay firing order on rock displacement in blasting a complex interbedded ore-waste structure. Examples of blasting a steeply dipping coal seams and bedded rock structure, especially in coal mining operations will be addressed and the comparison of efficiency in blasting in an up-dip as opposed to blasting in a down-dip direction will be discussed. Also covered in the paper is a new application of DMC-Blast to simulate a stope blasting underground. Simulations of blasting in a few selected types of timing/structure combinations will be presented in this paper.

Jan 1, 2000

By Catherine T. Aimone-Martin, Susan G. Beattie

A series of small scale explosive tests were performed at a perlite mine near Socorro, New Mexico. The tests were designed to investigate the azimuthal or directional relationship between small scale geologic structures such as joints and the propagation of explosively-induced ground motions. Three shots were initiated within a single borehole located at ground zero at depths varying from 83 m (272 ft) to 10 m (32 ft). An array of three component velocity and acceleration transducers were placed in two concentric rings at distances of 20 m (66 ft) and 40 m (131 ft) surrounding the single hole at 7.5° , 15° , and 30° azimuths as measured from ground zero. Data from the transducers were then used to determine the average propagation velocity and waveform characteristics of the blast vibration through the rock mass at the various azimuths. The rock mass was mapped to determine the predominate joint orientations (strike and dip) and the average propagation velocities were correlated with this geologic information. The results showed that there is a correlation between the predominate joint orientation and ground motion amplitudes and velocity. The more predominate geologic structures allow the wave to follow along their strike thereby forming a planar path of least resistance and in turn, allowing higher velocities and amplitudes. Secondary joints or structures may act in concert with more prominent features to form a network of channels or paths along which the wave moves more freely than it may when traveling against the structures. The greatest azimuthal variations in velocity and amplitude was observed for the shallow shot at 10 m (32 ft) depth.

Jan 1, 1996

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000

By Daodu Opeyemi

This paper describes several damages of blasting operations on some case studies, analyzes causative factors, and emphasizes preventive measures. Due to several complaints from some host mining communities as a result of blasting operations; two quarries from Nigeria suburbs were visited for study. The blasting design parameters in the mining companies were examined. Also, the history and existing conclusion of the neighboring buildings were studied using structured questionnaire, personal contact and visual examination. From the study carried out, it was discovered that varying negative environmental and socio economic problems resulted from the effects of vibration and flyrock on the nearby agro mining communities. The consequences are not limited to distortion of landscape but also include extinction of some animals, poor agricultural productivity; such as damages to economic trees and reduction in the yield of crops, health problems as a result of shock resulting to psychological disturbances, communal conflicts, blast induced cracks of structures and sometimes total collapse of host agro mining buildings, thus indicating that most mines did not comply with the safety concept of the existing environmental laws and regulations. Based on the results of the study it was recommended that proper blast design of quarries/mines should be conducted and the compulsory use of seismograph will be crucial in developing predictions. Environmental impact assessment should always be conducted before, during and after each blasting operation. Other possible control of vibration, flyrock and airblast, are also discussed in the paper

Jan 1, 2009

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Robert Jacob Cefalo, Rio Tinto Kennecott

At the end of 2016, the Mine started a new ore phase in the section of the pit located on the East Wall. The East Wall geological structures required controlled blasting for peak particle velocity (PPV) frequency vibrations to protect the wall. Frequency controlled blasting using linear seed wave superposition modeling was required and implemented to reduce the far-field affects to the wall. This paper covers the work done by the drill and blast engineering group, controls used to protect the mine infrastructure, and the continuation of work-to-date of frequency controlled blasting for wall stability. The narrow width of the layback required the combination of hole sizes to blast large diameter production patterns with smaller diameter trim patterns in the same blast. A single blast had to use different burden & spacing and hole diameters and required the use of different timings throughout the pattern. Electronic detonators were required to limit blast vibrations and accommodate the specific timings needed to reduce low frequencies. The geotechnical group with the help of geotechnical radars worked with the drill and blast group on creating a tracking and reporting of blast performance. The radar readings informed the drill and blast engineers of the performance of the blast as it related to the long term performance of the highwall

Jan 1, 2019

By P J. Dailey, S L. Burchell, R F. Chiappetta

High-speed motion picture photography and its application to the mining, quarry, construction, and explosive industries has proven to be a valuable diagnostic tool. The techniques developed allow one to evaluate blasting performance, compare explosive efficiencies in relation to burden velocity, and estimate optimum delay times to provide adequate forward relief.

Jan 1, 1983