Search Documents

By Chad Ducey

The proper utilization of energy in an explosive column is of paramount importance to the success of any blast. Historically, Powder Factor (the weight of explosive per mass or volume of material to be blasted or its inverse), has dictated the blast design. The concept of Energy Factor is a more effective method to design a blast. In order to utilize explosives efficiently, the energy contained in any given product must be quantified. The Powder Factor method, although historically successful, assumes that a pound of cast pentolite affects the material to be blasted the same as a pound of ammonium nitrate / me1 oil (ANFO.) Years of experience and scientific testing have led the blaster in the field to believe otherwise. The next logical technological step is Energy Factor. The Energy Factor method that will be discussed in this paper takes into consideration not only the weight of the explosive, but also the weight strength (Cal/g) and the density (g/cc) to yield a constant relative Energy Factor. The result of such a method is a factor that can be used in the field exactly the same as Powder Factor, but that reflects the relative energy of any given product in terms that will reflect the relative cost benefit of that explosive selection. The Energy Factors associated with different available explosives make it possible to compare the difference in the amount of energy per loaded pound in each unit length of borehole. This paper will examine the concept of Energy Factor in an in depth manner and also compare this quantification method to that of Powder Factor. It will also demonstrate the value of using Energy Factor and how it can improve the efficiency of a blast design. The misconceptions that come along with using Powder Factor will be examined and comparisons will be made between boreholes loaded using Powder Factor and those that are loaded using Energy Factor. This paper will clearly define the differences between these blast design methods and allow the reader to realize the production, quality, and economic advantages of using the Energy Factor method.

Jan 1, 2000

By Norman Paley, Zachary Pickett

The Red Dog Mine is a high-grade zinc-lead mine located in northwest Alaska which began operations in November 1989. In June 2014 the upper half of a charge in a trim shot in the Aqqaluk pit deflagrated. No other holes in the area were observed to react and the remainder of the pattern was shot without incident. This was the only known case of a deflagration in the 25 years of operations. As part of the investigation into the cause of this incident rock samples were obtained from the area of this hole and from other areas in this pit. The samples were assayed and tested for reactivity using the Reactive Ground Catalyzed Adiabatic test. Approximately half of the samples were found to be reactive with standard blasting agents. Unexpectedly, some of these were found to be reactive with blasting agents doped with urea to act as an inhibiter. Relationships between element grades and reactivity and between Specific Heating Capacity and reactivity were developed; however, the small sample size led to these models having an unrealistically large number of geological model blocks tagged as reactive. A program to better understand the behavior by testing more samples was initiated. Drill core was selected based on the predicted level of reactivity using the aforementioned relationships. The samples covered a greater range of grades and lithologies and included rock from the soon to be developed Qanaiyaq pit. The samples were dry pulverized then split for elemental assay, Reactive Ground Catalyzed Adiabatic testing, Specific Heating Capacity (SHC) determination, and X-ray Diffraction (XRD) mineralogical analysis. From this data, a Red Dog Mine specific assay based classification for separating reactive from non-reactive ground was developed. Furthermore, it was possible to divide the reactive ground into two subgroups: i) rock which reacts with ANFO-emulsion blends even when manufactured specifically with a reactivity suppression agent like urea and ii) rock which reacts with ordinary ANFO-emulsion blends only when a reactivity suppression agent like urea is absent.

By Tom Hanke, Joe Strobbe

The 80 year old Theodore Roosevelt Dam built in a scenic canyon near Globe, Arizona is currently undergoing a major renovation. The old stone dam, built by hundreds of skilled stonemasons, is being covered with a new concrete face that will increase the dam height by 77 feet. The renovated dam will improve flood control and provide increased electrical power and recreation area. The contractor, J.A. Jones is constructing the new dam and powerhouse for the Bureau of Reclamation.

Jan 1, 1993

By Thomas C. Jones

The purpose of this paper is to disseminate new information for nonelectric blasting in trenching and construction work. The presentation is not designed or intended to discredit conventional electric detonators or use of MS connectors and cord. Its sole purpose is to inform the S.E.E. of new and exciting benefits realized by the use of the Hercudet non-electric system in the construction industry.

Jan 1, 1984

By Joshua Hoffman, Catherine Johnson, Braden Lusk

The practice of dual initiation using precise timing from electronic detonators in boreholes is thought to be beneficial for increasing fragmentation at a desired location in the rock strata. This increased capacity for fragmentation is understood to be a product of both the collision of detonation waves in the explosive column and an increased energy liberation rate, each resulting from dual initiation. In addition, the collision of shock waves from two adjacent blast holes is suggested to improve fragmentation at the location the two shock waves meet, which can be controlled with precise timing. This paper presents the results from scaled laboratory experiments where converging detonation waves and shock waves were studied.

Jan 1, 2014

By Norman S. Smith, Richard L. Ash

Many factors affect rock fragmentation from blasting. One variable seldom considered when designing blasts, however, is the borehole length. An example is described of how the length was adjusted to give better breakage when using 4-inch diameter blastholes at a quarry. To explain the basic principles involved test results from experiments conducted by the authors where borehole lengths were altered are presented and evaluated.

Jan 1, 1976

By Mark S. Stagg, Rolfe E. Otterness, Stephen Rholl

The Bureau of Mines is engaged in research to develop and test high explosive fracturing and rubblization techniques that will enhance ore body permeability and thus increase recovery during in situ mining. The natural permeability of many ore bodies is too low to allow successful in-place leaching. These deposits could be profitably mined if flow rates of leach solutions could be increased. Blasting represents a potentially low-cost and effective permeability enhancement technique.

Jan 1, 1991

By K Uenishi, H P. Rossmanith, N Kouzniak, A Daehnke

This contribution presents an introduction into that part of the field of elastic wave propagation which is relevant to blasting of boreholes and addresses briefly borehole breakdown and the formation of the fracture network around a borehole which ultimately leads to the disintegration of the rock mass. Phenomena of this kind are encountered in mining and quarrying. Numerical as well as experimental work referring to stress wave expansion from a detonating borehole is addressed.

Jan 1, 1998

By Shijie Qu, Paul N. Worsey

Pre-splitting has become widely adopted for the formation and protection of final surface rock excavation profiles in both large scale civil construction and highway rock cuts. Jointing has been shown to affect the success of pre-splitting and the smoothness of the resulting profile, however, only closed joints have been investigated. Frequently jointing that is closed at depth is open at and near the surface due to weathering, reduced stresses and ground water percolation. In many instances, problems are associated with surface rock layers whereas at depth these problems are either reduced or do not exist.

Jan 1, 1987

By John C. Didlinger

How do you measure the highwall? Why do you even need to know the highwall measurement? Why is it important? The importance of this measurement is to help keep a level floor and to help control vibration. Nevertheless, since most of us are not mountain climbers, there must be a safe and easy way to make an accurate highwall measurement. So with these factors in mind, how do you make your measurement?

Jan 1, 1997

By Koichi Kurokawa, Takeo Ueda, Yoji Tasaki, Masashi Nakano

We have developed a new firing system which simplifies the handling and extensively increases the safety in electric blasting operations. Based on the principle of the transformer, this system is operated as follows: When a high frequency alternating current pulse (70-110 kHz) is applied to the lead wire and connecting wire (primary circuit), magnetic flux is generated in the transcore, and an induced current flows through the looped leg wire of the detonator (secondary circuit). Then the detonators are ignited by the induced current.

Jan 1, 1986

By Thomas M. Keevin, Gregory L. Hempen

Natural resource agencies, under various regulatory authorities, are challenged with permitting underwater explosive use while at the same time protecting aquatic resources. Deciding on whether or not to allow use of explosives requires striking a balance between development and aquatic resource protection. A company's goal in underwater explosive use is to select methods that are both expedient and cost effective. Use of explosives is often the best alternative for engineering reasons or economic considerations. Over and above legal requirements, indiscriminate destruction of fish and other aquatic resources is not in a company's best interests because of concerns relating to public image, as well as the need to secure future contracts.

Jan 1, 1995

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By Carl Hendricks

AQUILA Mining Systems Ltd. is the world leader in drill monitoring, control and GPS based drill navigation systems for the mining industry. This paper will review the general design and application of AQUILA.s drill systems currently in use throughout the world and the key benefits that derive through their use.

Jan 1, 2002

By Scott E. Winston, Spencer C. Watson

Dynamite is a generic term for a variety of high explosive formulations containing a blend of liquid and solid nitrate esters co-mixed with solid oxidizers and carbonaceous fuels. Dynamites can be divided into general classes of nongelatins, semi-gelatins, and gelatins which vary as to their detonation rates, densities, and water resistance. There are also numerous products within each classification depending on their utilization or on their permissibility in various types of underground mining operations.

Jan 1, 1985

By Malcolm Scoble

The estimation of digging, ripping and blasting requirements in advance of mine production is a difficult task. The characteristics of the superficials and rock mass govern the type and intensity of ground preparation required as a prelude to loading. The incentives for optimum planning of preparation are primarily economic but also relate to mining method and equipment selection, productivity and environmental impact.

Jan 1, 1985

By Feng Shuyu Yang Nianhua

According to the results of high speed photography tests, particle velocity measurement tests and the digital calculation with TP2 software, the shape of shock wave, the declined laws of the shock wave propagation speed and the peak particle velocity are described and analyzed in detail. New viewpoints about the theories of blasting fragmentation based on analysis of the progressive pictures of the fracture region are given. The formula for calculating the depth of fracture regions is established on the basis of the new viewpoints.

Jan 1, 1997

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Michael Wieland

Delay blasting in underground coal generates shock waves and rifting forces that damage charges remaining in the blast pattern. Damaged charges detonate poorly, raise fume toxicity and reduce coal breakage. Such circumstances could be prevented by using explosives resistant to cross-hole interaction damage. The design of rugged explosives is fraught with contradictory requirements, but tradeoffs related to hard-particle size characteristics prove useful. Hard particles, related voids or trapped bubbles represent reaction nucleation centers which strongly influence the performance of coal mine explosives.

Jan 1, 1992

By Elaine Gorham-Bergeron

CAROM is a distinct element, dynamic code developed at Sandia National Laboratories to calculate the motion of rock fragments during blasting.[1] It has recently been improved to incorporate a mechanism for its elements to mimic non-circular rock fragments. With this option, elements stack and move in ways that are characteristic of irregular boulders of blasted rock. In bench geometry, CAROM has been used to examine the possibility of producing variations in muckpile shape due to variations in detonation-time delays between rows. Surprisingly, the shape of the muckpile was predicted to be insensitive to time delays between detonation of rows of explosive, except where the rock fracturing was affected by the time delays.

Jan 1, 1987