Search Documents

By Ashraf M. Eid

Most research dealing with the problem of laterally loaded piles has been the response of individual piles subjected to lateral loads and/or bending moments. However, piles are seldom used individually but are normally constructed in clusters or groups. Little information is available of the effect of pile-soil-pile interaction (PSPI) on the performance of the group. This may be attributed to the difficulty of carrying out full-scale tests. Such tests are prohibitively expensive and require special installations to provide the required large lateral loads. The problem of laterally loaded single piles or pile groups involves the complexity of extending the theoretical solutions to the limits where the actual soil behaves nonlinearly. As the load increases, the elastic soil behavior cannot be adopted for design. Nonlinear soil behavior or the elasto-plastic behavior is evident. This research consists of experimental and theoretical models. The experimental work was conducted on models of free head pile groups in different configurations. The piles were in a sand formation and compared to the behavior of a single pile. The possible factors that influence the group behavior could be visualized. The experimental data was also compared to the widely used theoretical approaches to determine their adequacy. The analytical model makes use of the finite difference approach to calculate the soil non-linearity. A new approach equates the measured ground deflection and maximum bending moments of each row at every load level with the analytical model of single pile. This is the Deflection-Moment Fitting (DMF). The most suitable non-linear soil modulus modes and row contributions could thus be determined. Design of pile groups can be based on data pertaining to soil characteristics of the single pile. Results of the analysis were consistent with other approaches and proved to be adequate for design.

Jan 1, 2005

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By Kazuyoshi Kamimura, Masaya Kawata

"It has been 30 years since the cement deep mixing (CDM) method developed in Japan. CDM method has been applied to many structures. While various technical improvements have been implemented in the meantime, the single-axial and double-axial technologies used at the time of its initial development are still prevalent.In response to the recent trend of reducing construction costs, we developed a triple-axial CDM method called the “Lemni 2/3 Method.” This method uses two lemniscate motions caused by newly developed auxiliary stirring devices and employs a double-axial injection method in which the cement slurry injection takes place only from the outer two axes. In this way, it is possible to create a stabilized body around the three axes. Moreover, this method does not require substantial equipment investment as conventional construction machine and facilities can be used without modification and large volume work is possible.With these technologies, this method can achieve a substantial reduction in the construction period and cost, while ensuring the same level of improvement quality as conventional methods. As a result, this method is being applied to ground improvement work in a variety of places.Lemni 2/3 Method was first put to practical use in 2004. Since then, the method has been used for ten projects. In this paper, we show some application examples of this method.OUTLINE OF TRIPLE-AXIAL CDM METHOD (LEMNI 2/3 METHOD)In the newly developed CDM method (Lemni 2/3 Method), work efficiency is improved by employing triple-axial stirring blades instead of the conventional single- or double-axial type. Existing conventional construction facilities for double-axial type can be used with only minor equipment additions, because the cement slurry injection takes place only from the outer two axes.Construction Machine and Construction MethodThe combination of major construction machines of the Lemni 2/3 Method differs little from the standard specifications of the double-axial type as shown in Fig. 1. Existing work control equipment can be used without modification, which is further evidence of the simplicity, convenience, and economy of the new method. The Fig. 2 photo shows a full view of the construction machine, and the Fig. 3 photo shows the stirring blades and the auxiliary stirring devices. The work procedure for the Lemni 2/3 Method is shown in Fig. 4."

Jan 1, 2015

By Paul M. Schuman, Alessandro Bertero, Giuliana A. Zelada, Sharon G. Cranston

Many jet grouted columns were recently installed to create a jet grout-treated soil foundation for an earthen embankment used in a large shoreline stabilization project in the Mystic River in Charlestown, MA. A physical test program was used to determine whether the jet grouting parameters the Contractor selected would meet the design requirements given the local soil variability, including soft river sediments and organic soils. The presence of hydrocarbons encountered in the marine sediments during the test program caused concern that the design strength could not be achieved. The published literature discusses the environmental aspects of jet grouting with hydrocarbons. The literature did not include many studies of the effect on jet grout-treated soil strength for the types and concentration of hydrocarbons encountered on this project. The grout mix, air pressure, and number of passes of jet grouting were varied in a second field test program to determine jet grouting parameters needed to achieve the design strength of columns with hydrocarbons. A geo-probe study was performed to identify the type and concentration of hydrocarbons on the site. With few exceptions, the quality control core samples from the production columns met the design requirements with many strength values far exceeding the design strength. This paper presents the data, and reviews the lessons learned. PROJECT BACKGROUND The Charlestown Bus Garage, located in Cambridge, Massachusetts, is a Massachusetts Bay Transportation Authority (MBTA) bus maintenance facility located on the Mystic River. The site was home to a coal gasification facility before it was developed by the MBTA as a bus garage in 1978. A deadman-anchored steel sheet pile bulkhead wall installed along the Mystic river on the east side of the site supports the site grade at about El. 11 ft (NAVD 1988) (Figure 1).

Jan 1, 2019

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By Steven E. Darnell, William W. Haasz, Brandon T. Buschmeier, Frederic Masse

"Landfills often cover expansive areas in locations where large building facilities or infrastructure is in high in demand after the land has been reclaimed. Most landfills have soil or fill properties that vary widely over small distances; combined with the strict guidelines and restrictions for the removal and treatment of soil or material that is on site, these projects can be a major challenge for any prospective developer. In order to make landfills suitable for the construction of any project it is necessary to conduct a detailed evaluation of the subsurface conditions. Ground improvement techniques are among the most typical methods for making reclaimed landfills suitable for the construction of any major project. The paper will discuss the approach that was taken to support a proposed warehouse in Elizabeth, New Jersey using Controlled Modulus Columns Rigid Inclusions (CMC Rigid Inclusions), which are grouted, auger-displacement elements. Additionally, we will discuss the use of Dynamic Compaction (DC) that was performed in areas outside the proposed warehouse footprint. Through the combination of CMC rigid inclusions and DC, the general contractor’s project schedule was expedited, the costs to support the warehouse were economized, and the anticipated settlement of the parking lot areas was drastically reduced. Furthermore, the paper will outline the benefits of using CMC rigid inclusions and DC methods in order to minimize the impact of working with contaminated soils from a landfill.OVERVIEW OF THE ELIZABETH WAREHOUSE PROJECTOver the past several decades the foundations industry has seen an increase in demand for the support of developments on reclaimed landfills; particularly, on the east coast where many landfills were capped before the 1980’s and steady population growth and city expansion have caused high demand for this now highly desired real estate. Unfortunately, these landfills, often as large as twenty (20) or more acres present tough geotechnical and environmental challenges for Owners planning to develop or build structures of any size on the reclaimed land. Consequently, the options for building on reclaimed landfills can quickly become cost prohibitive.Site SpecificSelected by a developer for the location of a future warehouse, the 29 acres (114,424 sq-meters) project site is located in Elizabeth, New Jersey and demonstrates the complexities of designing over a once reclaimed landfill. The landfill was used for municipal solid waste (MSW) consisting of trash, wood, metal, glass, plastic, brick, concrete fragments, and other types of debris. This landfill was capped in the 1960’s, and developed in the 1970’s for a warehouse. The new project included the demolition of the existing warehouse and the development of the site to be repurposed for a new 481,650 sq-ft single-story warehouse, surrounded by paved parking and truck loading areas. Figure 1 below, shows an overview of the project site layout."

Jan 1, 2017

Technically speaking, the concept of NDT sounds like the "magic bullet" when faced with a questionable drilled shaft. All the Contractor or Engineer needs to do is select an NDT method, apply it, understand the details and extent of the defect and determine whether it will impact the load carrying capacity of the shaft during it’s design life. Unfortunately, it is not that simple. NDT is a tool utilized to indirectly assess the condition of the completed drilled shaft. For the most effective interpretation, NDT data should be correlated with the subsurface information, visual observation, and detailed shaft installation records. The basis for acceptance or rejection of drilled shafts should not be solely based on NDT. The parties responsible for specifying, interpreting and using the NDT results must understand the capabilities and limitations of the method to be utilized, in conjunction with the relevant subsurface conditions of the site, before selecting and specifying a system and acting on the results. This is necessary so that an appropriate NDT method can be specified and contracted. In this manner the results and roles of the responsible parties can be clearly defined.

Jan 1, 2004

By S. Y. Fantaye

This paper discusses the design, construction and performance of a 30 inch thick diaphragm wall recently constructed in Baltimore, Maryland at Inner Harbor East. The project site is an established marina and waterfront property. The geologic profile consists of fill, alluvial silt and clay, Potomac sand and clay, decomposed rock, and weathered rock on top of gneiss bedrock. The approximately 1,300 ft long perimeter diaphragm wall serves as a water cut-off, perimeter basement wall and support of excavation for the high rise project?s five levels of below-ground parking. Due to the fast track construction and the tight schedule, the initial design of the diaphragm wall was based on a limited amount of geotechnical information. Supplemental borings were then performed along the alignment of the wall to verify the design assumptions and wall depths. Additionally, the design criteria required that the wall be keyed into a competent stratum with low permeability. The Engineer of Record for the diaphragm wall, Mueser Rutledge Consulting Engineers (MRCE) completed the design and produced accelerated construction documents allowing the developer to release the drawings early for bid. This paper describes the theoretical soil parameters used to develop the loads, moments, and shears for the design of the diaphragm wall and the temporary tieback anchors. It also discusses the refinement of these soil parameters using the observed wall displacements and tieback pre-stressing forces as a baseline. This paper compares the calibrated parameters to the values used in the design of the wall. It explains how the soil structure interaction model was developed and the soil parameters calibrated using PLAXIS 2D non-linear finite element software. The paper also discusses the use of the proprietary CWS joint by Soletanche/Inquip JV as end stop between consecutive wall panels and the unique top-down construction utilized to support the diaphragm wall at the Southeast double re-entrant corner.

Jan 1, 2008

By Uwe Hess

For the Danish landworks for the coming fixed link between Denmark and Sweden across the Øresund the focus has been on the environmental aspects of the construction and operation of the facilities. This paper describes how the environmental objectives pertaining to the project have influenced the design and construction of one of the major elements of the Danish landworks, i.e. the tunnel in Sydhavnsgade and under Sydhavn Station. The chosen construction methods for the construction pit bracing and the groundwater lowering will be described along with the observed effects on the environment as shown by simulated or measured values for noise impact, settlements, pumped groundwater and extension of the drawdown cone.

Jan 1, 1996

By Aaron L. Sacks, David R. Good, Srinivas Yennamanda, Joseph K. Carey

Construction of Parcels 6 and 7, the second phase of The Wharf, began in 2019 and geotechnical construction was completed by December 2020. The overall project consisted of horizontal site, parks, and office buildings. The Wharf’s Phase 2 development includes approximately 1.2 million ft2 (110,000 m2) of above-grade construction including five multi-story, mixed-use buildings constructed over up to three levels of underground parking. The site is located between the WMATA Green Line Tunnels to the north and the Washington Channel to the south; it is bisected by a 108-in. (2740-mm) diameter DC Water outfall pipe. This arrangement, along with very difficult ground conditions, created challenges in the geotechnical design and construction. The support of excavation for this complex project required several different methodologies, including sheet piles, soldier piles, displacement piles, tiebacks, deep foundation anchors, jet grouting, and internal bracing with multi-tier rakers. Ground improvement was also required for support of spread footings in soft soils over the garage footprint. Underpinning of the active 108-in. (2740-mm) diameter DC Water outfall pipe running on a north/south alignment through the center of the site between the two garage structures was also performed. Since portions of the support of excavation are below the groundwater table, an extensive pre-excavation dewatering program was necessary and was separate from the foundation package. On the north side of the project, support of excavation (SOE) was required on a curved alignment, offset approximately 10 ft (3 m) from the outbound Green Line tunnel. Due to the proximity of the tunnel, a stiff, near-zero displacement wall was required. A portion of the buildings extend over the tunnels, imparting load to the tunnels to approximately restore original overburden loads excavated for the basement space. The building foundation is a 3 to 4-ft (0.9 to 1.2-m) thick mat slab anchored into the Potomac clay formation. Continuous movement monitoring of the tunnels was performed by an automated system. This paper describes the design and construction of the SOE and foundations for this high-profile project, which required collaboration between the Owner, Engineer, Construction Manager, and Specialty Geotechnical Contractor to solve many challenges.

Oct 1, 2022

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Terry Eldridge, Keith MacKay, David Siddle, Luke Moger

On August 4th, 2014, a breach occurred in the Perimeter Embankment of the Tailings Storage Facility (TSF) located at the Mount Polley Mine, releasing approximately 10.6 million m3 of supernatant water, 7.3 million m3 of tailings solids, 6.5 million m3 of tailings interstitial water and 0.6 million m3of construction materials. A Temporary Upstream Rockfill Berm was constructed between August 2014 and February 2015 within the area of the tailings dam failure in order to retain the remaining tailings solids during the low flows of the winter season. The Temporary Upstream Rockfill Berm was constructed as part of the initial response phase, with the primary objective to abate the flow of tailings into the receiving environment. A secondary objective of its construction was facilitating the required investigation works downstream of the tailings dam failure. The selection of the coarse grained material used in the construction of the Temporary Upstream Rockfill Berm was based on the availability of the material (timeliness of construction) and the non-water retaining design of this initial response phase. Consequently, an alternative method was required in order to prevent further loss of mine-affected water and tailings from the TSF, as well as to provide short-term contingency water storage, during high flow conditions expected in late spring. Golder Associates Ltd. designed the 2015 Freshet Management Embankment, a deep mixing cut-off wall, to meet these site requirements, which was constructed by Mount Polley Mining Corporation and Golder Construction Inc. between December 2015 and April 2015. The works included 132 soil cement panels constructed to depths of up to 27 meters. This aspect of the works was completed using an RG25S Bauer CSM rig on a 24 hour per day, 7 day per week schedule. The cut-off wall specifications included a target unconfined compressional strength (UCS) of between 1 and 2 MPa, a maximum hydraulic conductivity of 1x10-6 cm/s, and a ductility to enable the soil cement to undergo a minimum of 5% strain without a reduction in strength or increase in hydraulic conductivity. In order to control and assure the quality of the soil cement, 2553 wet grab specimens were retrieved from the fresh soil cement panels using a project-developed sampler. Four of the soil cement panels were cored with a mud-rotary drill rig and optical and acoustic televiewers were placed into the boreholes in order to log several relevant parameters, including image, texture, relative hardness, borehole-shape, and temperature.

Jan 1, 2016

By Brent Wilkins

The project team was tasked with the design and installation of a deep foundation system to support an expansion to a power generating station in Glenrock WY. Cast-in-place piles installed by a fixed mast drilling platform were assessed to be the most efficient foundation system for the subgrade conditions and range of design loads for the project. It was determined that conventional augered, cast-in-place piles could not be installed to the required pile toe elevations. Subsurface materials consisted of interbedded coarse- and fine-grained soils to about 23 ft to 30 ft depth below the ground surface, underlain by carbonaceous shale (claystone) with interbedded sandstone. The overburden materials varied from very soft to medium stiff and loose to dense. The claystone was typically foliated and very weak to weak whereas the sandstone was typically massive and very weak to weak. The site characterization consisted of a variety of field and laboratory programs including soil borings with Standard Penetration Tests, pressure-meter testing, and geophysical testing. A load test program was performed involving the compressive, lateral, and tensile testing of piles ranging from 14-in to 24-in diameter. Compression test piles were instrumented with vibrating wire strain gages. The paper includes a discussion of the regional and local geologic and geotechnical parameters, particularly the results of the various in situ and laboratory test programs. The selected foundation system is introduced. Load test results are then presented along with analysis and discussion of these results with regard to performance of the piles in the claystone.

Jan 1, 2009

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Anthony L. Reynolds, Clifford J. Wren

"The adoption of a significant pile testing regime, the use of Eurocode 7 as the design standard, the development of lean construction techniques, and lateral thinking in overcoming some considerable construction challenges allowed Stent Foundations to construct the foundations for the new Wembley Stadium, London, on time and within budget. In addition to the piling works for the main stadium, and after significant design development, a large number of extra piles were required to raise the new iconic roof Arch to its final position some 133 metres above the ground. A 1,400m long contiguous bored pile wall was also constructed to allow for excavation and formation of the new pitch. INTRODUCTIONHjstorjcal lntrodyctionWembley Stadium is the 'home of English football'. As long ago as the 1880's, Wembley Park leisure grounds had football pitches and running tracks.In 1918 the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Exhibition area covered 219 acres and the area on which a former abandoned tower called Watkins Folly had stood was chosen as the site for the new stadium (http://www.wembleystadium.com).The Empire Stadium, as it was originally known, was designed by architects Sir John Simpson and Maxwell Ayerton and the engineer Sir Owen Williams. It took just 300 days to complete at a cost of £750,000 ($1.4m), and was built using 25,000 tons of ferro concrete, 1,000 tons of steel, and over half a million rivets.The Empire Exhibition was a remarkable event, containing fountains, lakes, gardens, and many pavilions, each representing the architectural style of the countries exhibiting. It was opened on 23rd April 1924 and the final attendance was over 27 million, with 4.5 million admissions to the Empire Stadium alone."

Jan 1, 2005

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Gregory A. Stephan

A case history of design, prediction, instrumented static load tests on probe piles, installation monitoring, and integrity testing of production piles is presented. Based upon project-specific subsoil conditions, as obtained from several 60 to 80 ft (18.3 to 24.4 m) deep test borings, deep foundation system alternatives included driven concrete and steel pipe piles as well as augered cast-in-place (ACIP) piles. High structural loads, site-specific constraints, and the production time frame mandated by the project owner led to the selection of an ACIP pile foundation system that was designed for a pile capacity of 75 tons (667 kN) in compression and 35 tons (309 kN) in tension. Site-specific concerns were raised about the highly porous nature of fragmented and decomposed sandy limestone as well as the high grout intake during construction that could result in increased foundation cost as well as interconnecting of the piles in the rock layer. Consequentially, a multi-phase ACIP pile evaluation program consisting of instrumented compression pile load tests, in conjunction with single-hole ultrasonic pile testing, pile echo testing (sonic testing), as well as full-time production pile monitoring by an experienced geotechnician was specified. As a result of this testing and evaluation program, while grout usage was determined to be within an acceptable range, the instrumented compression load tests yielded data that allowed use of 55 ft (16.8 m) long ACIP piles in lieu of the original plans to use 70 ft (21.3 m) long precast concrete piles. This information was effectively utilized as part of the overall quality control program to install a total of 268, 14 in. (356 mm) diameter ACIP piles within the building footprint to depths of 55 ft (16.8 m) below the pile cut-off elevation as part of the foundation support system. Information recorded during installation included rate of insertion/extraction of the auger, grout pump strokes and pressure, total grout volume, and grout factors, as well as quality and strength of grout. Additionally, many pre-selected installed piles were tested for integrity with a Pile Integrity Sonic Analyzer (PISA) using both sonic and ultrasonic methods. This engineered, monitored, and tested foundation solution provided an effective and quality intensive basis for completion and approval of the foundation work for the building that resulted in cost savings over other foundation alternatives for the owner.

Jan 1, 1999

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022