Search Documents

By Kishore Kumar B., Eswaran Prasad C R, Srini Naik B., Ramakrishna Raju N

The authors through this paper intend to introduce the non-vibro technique of ground improvement by stone column, being used for the first time in India under the Western Dedicated freight Corridor in Mumbai area. New 2x25 KV double line dedicated freight corridor tracks, capable of carrying 32.5-ton axle load are proposed to be built on this stretch. Non-Vibro Displacement Stone Columns of 900 mm diameter were installed to improve the safe bearing capacity of the soft ground to take the loading of Dedicated Freight Corridor Railway embankment. Vertical footing load tests on single and three column groups were conducted to assess the improvement in the sub-surface condition after installation of stone columns. This paper describes load tests conducted on stone columns and analysis of the obtained results. The observed load settlement behaviour of the improved ground has also been presented. Behaviour of single and group of stone columns have been compared and criteria adopted for arriving at desired factor of safety based on the settlement observed, has also been discussed.

Nov 1, 2022

By Madan Kumar Annam, Hari Krishna Y, I. V. Anirudhan

"For completion of projects in time with positive results, improvements of productivity and effective project management procedures have become extremely important. This paper discusses a milestone project comprising 198 residential units of stilt plus 4 levels that highlighted the benefits of these key aspects. Success of ground modification procedure benefitting the entire cycle involving End Users, Suppliers, Bankers and Developer is discussed.Soil profile for a considerable depth comprises weak layers of silty clay and sandy clay with varying consistency. Deep foundations have been an automatic choice of foundation for major buildings constructed in similar environment. After serious geotechnical appraisal, reconsideration of the foundation system with an alternative solution of Ground Improvement was found to be optimal in terms of Cost and Time. Full raft foundation on the improved ground by installation of Vibro Stone Columns (dry bottom feed method) was considered as an alternative foundation system. The ground improvement works were completed within 6 weeks (as against 6 months to that of pile foundations) that was made possible through effective project management. Full size plate load tests were conducted to ascertain effectiveness of the ground improvement works. Success of the foundation system was proved by full scale monitoring of foundation settlement during and after completion of the project over a span of 2 years. This paper describes design considerations, quality control in the construction of Vibro Stone Columns (dry bottom feed method) and performance monitoring of the project thereafter.INTRODUCTIONGenerally in weak deposits, deep foundations like bored cast-in-situ piles and driven piles have historically been the foundation choice for major buildings and other structures. Construction of pile foundations is becoming a challenge due to their high cost, large construction time and due to severe environmental issues (noise pollution, ground vibrations and carbon footprint). Since the proposed building complex is located within the proximity of a well-developed residential locality, objections raised by neighborhoods to pile driving activities called for a rethinking on the foundation system.The top 6m to 8m of soil profile comprises of silty clay / sandy clay having highly varying consistency. GWT was encountered at 3.0m below the existing ground level. Under this situation, the reconsideration of the type of foundation system with respect to the geotechnical analysis gave a thought to assess feasibility of ground improvement system."

Jan 1, 2015

By Christophe H. Locussol

D.C. United, the professional soccer team located in Washington, D.C., completed a 20,000 seat capacity stadium in July 2018 named Audi Field. The project initially considered a foundation system consisting of roughly 800 prestressed concrete driven piles configured in groups with pile caps. A value engineering alternative proposed in a design-build manner ultimately resulted in the use of 300 single element Auger Cast Piles (ACPs) for the foundation system. The ACPs ranged between 1.5 ft and 4 ft in diameter, were up to 85 ft in length, and were connected through a system of grade beams to accommodate large lateral induced loads. Limitations in conventional analytical methods were encountered during the structural design of the piles due to the complexity of the lateral loading and pile fixity conditions. An innovative approach using advanced finite element modeling that incorporated the framing effects of the grade beams was required to meet the strict movement criteria despite large lateral loads.

By Carlandrea Albonico, Salvatore Miranda

After a brief introduction of the whole Project, the paper describes two special geotechnical engineering solutions provided within the scope of the Galataport Project, in Istanbul, Turkey. The first refers to the new quay of Salıpazarı, which is a combination of retaining structure and ground improvement, formed by a combiwall, a reinforced concrete diaphragm wall and a soil improvement by deep soil mixing (Turbojet). The second, refers to the soil improvement works executed underneath three existing buildings. Single-fluid jet grouting columns had the scope of improving the mechanical properties of the bearing soil and reducing the associated risk of liquefaction. A set of underpinning micropiles was installed in order to allow the excavation of a partial basement inside two of these three buildings. All activities were conducted from inside the existing buildings, with reduced headroom. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Hamed Layssi, Farid Moradi, Thomas Tingson

This paper describes the feasibility and pilot study of of using existing non-destructive testing solutions for evaluating structural integrity and mechanical performance of mass concrete foundations. This paper includes two pilot studies using well-known NDT methods (i.e., Crosshole Sonic Logging and seismic tomography) for new applications (i.e., NDT inspection of mass concrete foundations). In the first case, we will examine an existing mass concrete foundation block with internal cracking, which has negatively impacted the strength and stiffness of the foundation block. A combination of pulse velocity and 2D tomography was used to evaluate the structural integrity in the foundation block. In the second case, the quality and integrity of newly built mass foundations were evaluated using Crosshole Sonic Logging (CSL). The methods are combined to locate potential sub-surface defects such as large voids and discontinuities. This paper aims to study the effectiveness of the NDT methods of Deep Foundations to assess the quality and structural integrity of new and existing mass foundations and explore the opportunity to extend the capabilities of these tests beyond their conventional use.

Sep 8, 2021

By Brian M. Fraley

"Portions of the Catholic Total Abstinence Fountain in Fairmount Park in Philadelphia, Pa., were in “imminent danger,” according to a restoration services request for proposals (RFP) issued by the City of Philadelphia in August 2014. Open voids in the subsurface beneath the foundation were causing ongoing settlement of the fountain.The fountain was unveiled in 1876 as an ornamental drinking fountain for the Centennial International Exhibition, which celebrated the signing of the Declaration of Independence. Its creation was commissioned by the Catholic Total Abstinence Union of America, an Irish temperance organization that advocated for total abstinence from alcohol. Ironically, the fountain ran dry decades ago.The now-defunct fountain features a 100 ft (30.5 m) wide granite base with three steps in the shape of a Maltese cross. The centerpiece — enclosed by a 40 ft (12.2 m) diameter basin — is a 15 ft (4.6 m) tall statue of Moses perched atop an iglooshaped marble mound. Four subsidiary statues rise from granite pedestals at the tips of each arm of the cross, including Archbishop John Carroll, Charles Carroll of Carrollton, Father Theobald Mathew and Commodore John Barry.Natural and Man-Made DamageThe City of Philadelphia’s RFP called attention to three “high priority structural areas.” It was noted that Moses, Father Mathew and the steps surrounding the fountain had been documented as public hazards. The long-term effects of water infiltration had set in, eroding mortar joints and causing some stones to jut out. Furthermore, the stone base supporting the 16 ton (14.5 tonne) statue of Moses was in danger of collapsing. The statue of Father Mathew had been struck by lightning in 1910 and was repaired with an iron and metal pin anchor system, which had succumbed to corrosion. The city considered the statue of Father Mathew as the most threatened of the statues. Mike Miluski, P.E., vice president of Compaction Grouting Services (CGS), recalled “the fountain was in pretty bad shape” as he walked onto the site in August 2016 and immediately recognized the challenges ahead."

Jan 1, 2017

By Eleonora Di Mario, Colin B. Turnbull, Matthew G. Mills, Chengbin Miao, Wilhelm S. Degen

"In the past decade, the ‘zero-dredge’ philosophy has become the preferred option for the formation of marine seawalls and reclamations, compared to the partially or fully dredged options, as this solution presents several environmental advantages. Recent relevant project experience is presented herein in order to highlight key design principles and construction issues central to the successful construction and performance of a sloping rubble seawall founded on soft soil improved by stone columns. If designed and installed with proper quality control, correct treatment intensity and sensible construction staging, stone columns are a safe and cost effective method for seawall foundations. This paper provides guidelines with regards to the design, construction and quality control for the correct implementation of stone columns as a foundation element for sloping rubble marine seawalls.INTRODUCTIONBenefits of sloping marine seawalls founded on stone columnsTo suit the current environmental requirements in Hong Kong, recent projects are tending to favour zero-dredge solutions, such as the Hong Kong Boundary Crossing Facility and the forthcoming Three-Runway System. The installation of stone columns allows the underlying deposits, generally consisting of very soft to soft clay and silt (soft soil), to improve in strength to the extent that the seawall can be directly placed on the seabed. This negates the need to dredge the soft soil and, therefore, this ground improvement technique represents an ideal solution for zero-dredge projects.Stone columns can also provide several other beneficial effects, including: accelerated drainage, reduced settlement, increased slope stability and soil reinforcement in the event of an earthquake. Stone columns, in contrast to competing cementitious methods, are a very ductile foundation method. This ductile behaviour is part of the design concept of stone columns in soft soil. Past projects located in Hong Kong and elsewhere, with an improved soft soil layer thickness of over 15m, have shown that stone columns can remain fully functional in terms of both drainage and horizontal reinforcement, even after settlements of over 3m and lateral displacements of up to 1m have occurred."

Jan 1, 2017

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By Benjamin B. Buensuceso III

Crosshole sonic logging (CSL) is a popular quality assurance and quality control method used to examine the concrete quality of cast-in place deep foundations, though the evaluation of the results is subject to certain limitations. One such limitation explored in this paper is the occurrence of false positives, where signal anomalies indicated by CSL test results are not necessarily indicative of imperfections in the foundation that could affect its performance. A case study of false positives evaluated in CSL records in a major infrastructure project in Metro Manila is presented in this paper. A detailed desktop evaluation and results from complementary high-strain dynamic load testing and low-strain pile integrity testing were used to evaluate the significance of the suspected false positive signal anomalies from the CSL test results. Recommendations for the proper interpretation and evaluation of CSL test results in Philippine practice, given the method’s limitations and examples presented, are also shared.

Sep 8, 2021

By Gerald Verbeek, Erick Baziw

"Downhole Seismic Testing (DST) is an important geotechnical testing technique for site characterization as it provides low strain (<10-5) in-situ interval compression (Vp) and shear (Vs) wave velocity estimates. These velocities are determined by obtaining relative arrival times of source waves as they travel through the stratigraphy and are recorded by one or more vertically offset seismic sensors. A challenging aspect of this process is to characterize the seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. This paper introduces an assessment technique which utilizes linearity estimates (i.e., hodograms fitting straight lines) from the polarization analysis in conjunction with crosscorrelation coefficient calculations of the full waveforms as well as the deviation of the source wave frequency spectrum from a desirable bell-shaped curve. The paper will provide an overview of the technique and include some examples of actual data sets where the technique was applied to analyze those data sets.1. INTRODUCTIONIn general terms, Downhole Seismic Testing (DST) such as Seismic Cone Penetration Testing (SCPT) is a geotechnical technique for measuring in-situ shear and compression wave velocities (VS and VP respectively). The main goal in DST is to obtain arrival times as the source wave travels through the soil profile of interest, and from these arrival times the velocities are then calculated. Figure 1 shows a schematic of the typical DST configuration: a seismic source is used to generate a seismic wave train at the ground surface. One or more downhole seismic receivers are used to record the seismic wave train at predefined depth increments. The downhole receiver(s) may be positioned at selected test depths in a borehole or advanced as part of an instrumentation package as in the case of SCPT. When triggered by the seismic source a data recording system records the response of the downhole receiver(s)."

Jan 1, 2017

By Leong, William. Chong, Kam Weng

Deep Vibro Techniques namely Vibro Compaction (VC) and Vibro Replacement (VR) are widely used in ground improvement to densify sands and strengthen cohesive soils. This paper describes the application of these techniques for the construction of 20 Ha Iron Ore Stockpile Yard with the maximum stockpile height of 14 m in Quang Ngai, Vietnam. The challenges of this project are to limit the stockpile allowable settlement and the surrounding pile’s lateral movement. The soil condition can be summarized as 12m – 18m thick of loose to medium dense SAND with qc around 5-18MPa and followed by 2.0 – 6.0 m thick soft clay with qc around 0.4 – 0.8MPa. Localized very dense sand layer was found. VR using stone columns were installed in soft clay layer while VC was adopted to densify sand layer. Additional shallow stone columns were built in sand strata to minimize pile top lateral movement. The post construction performance was verified by a large 6 m by 12 m plate load test (PLT). The predicted PLT deformation using Priebe’s improved properties for the VR will be presented and compared with the measured plate load test results.

Nov 1, 2022

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Rich A. Lamb, Paul J. Axtell, Michael K. Muchard

"Since 2010, the Minnesota Department of Transportation (MnDOT) has performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. All of the piles were 42-in diameter, open-ended pipes driven to practical refusal on sedimentary bedrock with D125-32 diesel hammers from three separate manufacturers. The rapid load test method in general accordance with ASTM D7383-10 (Statnamic method) was used along with high-strain dynamic testing and subsequent signal matching. Results of these tests indicate that the axial nominal resistance of these piles in compression is not controlled by geotechnical considerations when driven with an appropriately sized hammer and installation criterion. Rather, the predominantly elastic load-deflection behavior of the piles under compressive load suggests the axial nominal compressive resistance is controlled by the structural capacity of the pile. In all instances, the rapid load tests indicated a nominal resistance exceeding that produced by high-strain dynamic tests due to insufficient hammer energy to fully mobilize resistance. In all cases, the hammers used were able to easily install the piles through the soil overburden. Mobilizing a larger hammer simply to demonstrate high-strain dynamic resistance is not economical or practical. This paper presents the subsurface conditions at each location, the ensuing test results, and the ramifications for future projects in Minnesota utilizing large-diameter open-ended pipe piles.INTRODUCTIONThe Minnesota Department of Transportation (MnDOT) has recently performed eight full-scale compressive load tests on large-diameter pipe piles at four different project locations across the state. The four project locations described in this paper where pile load testing was performed are shown in Figure 1 and exist in the southeastern portion of Minnesota. The projects are all major bridges crossing the Mississippi River in three instances and the St. Croix River just above the Mississippi River in the other instance. The first project is the TH 61 Mississippi River crossing in Hasting, MN where two load tests were conducted. The second is the TH 36 St. Croix River crossing in Stillwater, MN where two load tests were performed. The third project is the I-90 Mississippi River crossing in Dresbach, MN where three load tests were conducted. The final project is the TH 43 Mississippi River crossing in Winona, MN where one load test was performed."

Jan 1, 2017

By Takefumi Takuma, Hiroyuki Nishimura, Shigeru Kambe

"In order to achieve tubular pile driving with low noise and low vibration, the Press-in Piling Method has been adopted on many projects. The method utilizes reaction force derived primarily from previously driven piles to push in the next pile into ground. With attachments, the Press-in piling equipment can deal with hard soil as well as difficult site conditions. At West Toronto Diamond Rail Grade Separation Project in Toronto, Canada, the Press-in piling equipment drove more than 500 of 914 mm (36 inches) diameter tube piles in length of 12 to 25 meters (39 to 82 feet) to construct earth-retaining walls for railway grade separation. Myoshoji River Restoration Project in Tokyo, Japan drove some 600 of 1,000mm (39.4 inches) diameter tube pipe sections in length of 11 to 22 meters (36 to 72 feet) by the rotary Press-in piling equipment to increase the flood drainage capacity of an existing river in highly populated area of the city. Both projects exemplify the advantages of the method in urban settings.1. BACKGROUNDThe Press-in Piling Method was invented some forty years ago in Japan, where a very large number of construction projects were causing widespread construction pollution, especially by pile driving work in densely populated areas. The method has been providing solutions for piling projects which could not have been built otherwise due to the noise and vibration impact to the surrounding communities. The method can be used with various types of piles including sheet piles, tubular piles, concrete sheet piles and so on. With high pressure water jet and continuous flight auger attachments, the Press-in piling equipment can deal with dense sand, stiff clay, gravels, boulders and even soft rock without employing a different set of equipment."

Jan 1, 2015

By Heman Manchanda, Sandeep Sharma

Several infrastructure projects are in various stages of construction and planning in India and almost all of them involves open ground excavation extending to varying depths. These structures are generally multipurpose and fulfil several needs of the society, their failure can be catastrophic. The design and construction of deep open excavations is generally associated with a high level of risks due to a whole series of uncertainties involved, and the success of such projects depends on various factors including appropriate evaluation of ground behavior and response to excavation stages, correct choice and analysis of construction supports, control of ground water flow during excavation, etc. One of the most critical amongst all these is ground water flow during construction and stability of underground excavation depends to a large extent on ground water control. This paper uses numerical studies for the assessment of the potential impact of ground water and ground water movement for the design of underground deep structures. The studies are being conducted using PLAXIS 2D finite element software and analysis all construction stages to which an open underground excavation shall be subjected. The paper discussed in detail the impact of water table fluctuations and comparative evaluation of different water flow conditions – a) Different Stages of excavation in line with the construction sequence (Phreatic), b) Coupled flow analysis (Transient- 1 year and 2-year duration) and c) Steady state flow conditions. The paper also covers seepage calculation and design of dewatering system.

Sep 1, 2022

By Maurizio Siepi, Paul van Horn, John Coupland, Julian Crawley

"TTMJ is the acronym for the Slurry (Diaphragm) Wall Tension Track Milled Joint currently in development as part of the European Union's innovative and far-reaching Horizon 2020 initiative (FTI Pilot-2015-1 720579). The TTMJ Project has been specifically set up to deliver this versatile new step-forward in Slurry Wall technology. The TTMJ System is protected by patent in Europe and the USA, and is currently under development by a consortium comprising Trevi SpA (Italy), Arup (Netherlands) and CCMJ Systems (UK). The principles of the TTMJ System together with the installation process are herein described in general terms. The system is still under development with field trials scheduled for early 2018, so some of the detail will not be disclosed at this stage. It is the intention of the Authors that the results of these field trials and a more complete description of the System will be presented in a paper we intend to submit for the DFI/EFFC International Conference on Deep Foundations and Ground Improvement to be held in Rome, Italy in June 2018. The final section of this paper explains how the TTMJ system can be applied to a common application of slurry wall construction; deep circular or multi-cell shafts. The system can be used to construct shafts more easily and at less cost than current methods. It also allows shafts with smaller internal dimensions to be constructed than is currently practical.INTRODUCTIONCCMJ Systems (UK) realised that an innovative new approach to forming joints in both Slurry (Diaphragm) Walls and Secant Pile Walls would provide greatly improved joint integrity to greater depths, to the overallbenefit of retaining wall quality, across the world-wide foundations industry.In particular this new system is designed to:??Increase the effective depth range of Slurry Walls (especially walls excavated by grab) and Secant Walls??Remove the requirement for Stop-ends or Joint Formers??Allow for a Shear Key at the joint??Allow for a Water Stop to be installed at the joint??Permit Continuous Reinforcement across the joint??Optimise Reinforcement Density and hence Concrete Flow??Facilitate joints in corner panels eliminating the need for “L” shaped cages and reducing largesingle-pour concrete volumes and slurry storage capacity requirements.??Enable the construction of smaller-dimensioned square and circular deep shafts (especially useful for city-centre sites) than is possible with current methods.CCMJ Systems approached other industry specialists with a view to forming a development team to explore the possibilities for this new technique."

Jan 1, 2017

By Hitendrabhai S. Dewangan, Dr. Aashish A. Mehta

Pile foundation is widely used in construction of marine structures. In offshore & marine piling work, drilling/boring supporting fluid is used to stabilize the borehole (excavation) prior to tremie concrete. The poly-fluid is a synthetic drilling granular polymer characterized by high molecular weight.it is mainly used for the preparation of stabilizing and lubrication mud in drilling of deep foundations. Disposal of polymers after using it into the sea, pollutant the sea environment, which may be harmful for living organisms inside sea. To reduce the pollution in offshore/Onshore, it is essential to take the precautions during flushing operation with proper recycled, reused & it’s Disposal. To provide economic and environmental solutions, used slurry was treated with addition dose of fresh material/polymers. The amount of fresh materials/ Polymer to be added can be decided based on (viscosity, density and pH value) test results. Finally, initiate water flow and air agitation as required. Run the tests on the re generated slurry before transferring to storage tank. Also, after storage, polymers will be reused for next operation. Moreover, mud wastage coming from borehole will also be disposed at suitable dumping places.

Sep 1, 2022

By Shreya Vivek Hokam, Dr. A. I. Dhatrak, S. W. Thakare, Dr. Vivek S. Hokam

Construction in congested urban areas has necessitated tall and massive structures. In urban areas, it is common to construct underground structure nearby existing buildings. Selection of an appropriate support structure system to be implemented in the excavation in an urban area is heavily dependent upon the geotechnical conditions and safety of the surroundings and neighbouring structures. Urban Rail, popularly referred to as Metro Rail, has seen substantial growth in India in the recent years. More cities are experiencing the need for metro rail to meet their day-today mobility requirements. The metro structures involved deep excavation for foundations which induces the stresses and thereby alters the existing equilibrium and thus may affect stability of neighbouring structures considering safety point of view. Hence, design and execution of deep excavations become one of the important challenging tasks of any geotechnical engineer in the modern era. Further, it is important to control the ground movement in order to prevent the failure of excavations. This involves specialized foundation technologies, usage of sophisticated equipment and new methods in underground construction, safety and monitoring systems. In this paper the methodology used for protecting adjoining structures due to deep excavation for Nagpur Metro station is studied.

Sep 1, 2022

By Brandon Smith, William Bohlen

Riverbank erosion along the Brazos River has modified the structural support conditions for an existing bridge structure in Southeast Texas. The 8-span, 1,200-foot long bridge was completed in 1992 along Highway 99, a key corridor for the Houston area. Foundation support conditions have been altered due to natural, ongoing river morphology for three bents on the affected riverbank. Recent events include three storms within a three-year period that each exceeded the 500-year return probability. This resulted in accelerated erosion along the northern riverbank. Over forty vertical feet of soil has been removed in some locations. Drilled shaft foundations are now functioning as columns. This review considers the behavior of columns and deep foundation elements due to the modified support conditions. The review ultimately presents a rational methodology for the review of the present and anticipated future bridge configuration with respect to current strength, service, and extreme event limits, with corresponding safety factors for the design. Introduction and Background The Fort Bend Grand Parkway Toll Road Authority (Owner) oversees the State Highway 99 Judge Jodie Stavinoha Bridge over the Brazos River. The 8-span, 1,200-foot long bridge was originally designed with four southern approach spans of 115 feet; a three-span continuous river crossing with span lengths of 195 feet-235 feet-195 feet; and a single northern approach span of 115 feet. Figure 1 provides an overview of the northern portion of the bridge. Table 1 provides a summary of the original bridge substructure configuration. When the bridge was completed, the centerline of the Brazos River was located at midpsan of the main span and the northern high bank was originally located at Bent 7. Erosion process has forced the northern high bank to Abutment 9 (also called Bent 9), and the river centerline during normal flow conditions is located south of Bent 8. The overall estimated river excursion at present day is approximately 270 feet to the north from its original location. An erosion wall that was installed in 2017 limits further erosion of the north river bank within the 300-foot width of the roadway corridor right-of-way. This study was developed to better understand the existing conditions, and to forecast the need, nature, and criteria for potential future improvements.

Jan 1, 2019