Search Documents

By Robert Yobou, Jacques Naho, Benjamin A. Allou, Jacques Carignan, Huan-Zhang Lu, Jayanta Guha, Koffi Pothin

"Résumé - Les seules productions de columbo-tantalite en Côte d'Ivoire sont effectuées dans les éluvions, colluvions et alluvions d'Issia, au Centre-Ouest de la Côte d'Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n'a été accordée à l'étude de la minéralisation primaire en relation avec l'évolution de ces granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent: le granite orienté à deux micas (type Lobo), le granite orienté à muscovite dominante (type Bitapia) et le granite porphyroïde non orienté à muscovite dominante (type Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale montrent que: (1) les trois principaux granites de la région sont de type-S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite de type Issia fut le dernier à se former.Les pegmatites liées au granite de type Issia ont été classées en quatre types : A- pegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et D- pegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV- zone à microcline massive; V- zone à quartztourmaline. Ces pegmatites présentent une zone d'altération métasomatique externe.La minéralisation de Ta, Nb, et Be est liée à la zone III des pegmatites de types C et D, la minéralisation de Li est associée aux greisens qui peuvent être observés n'importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite de type Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite de type Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite de type Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma. Les éléments rares sont restés dans le liquide résiduel jusqu'à ce que les conditions favorables à leur précipitation soient atteintes.L'établissement de ce lien génétique ouvre des voies pour des nouvelles stratégies d'exploration."

Jan 1, 2005

By S. P. Lowe

Flotation testing of Flin Flon ore was started in the Denver laboratory of Complex Ores Recoveries Co. in March, 1926. There had been a considerable amount of flotation testing previously which had shown possibilities of success, and it was felt that, with the increased knowledge of flotation and the comparatively new reagents then available, flotation held out the best prospects for a successful commercial treatment of this ore. There remained available for this experimental work a small amount of the rejects from a thorough sampling of the mine and some ore from the mine dump.

Jan 1, 1930

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

By N. Hosking, M. Nichols

Aluminum alloys are increasingly used for automotive body construction but are susceptible to filiform corrosion or paint blistering in service. Filiform corrosion resistance of two 6000-series aluminum alloys was investigated in this work. Test panels were produced with full automotive coating layers and scribed parallel and perpendicular to the rolling direction. The corrosion exposure comprised an inoculation step with acidified salt solution followed by a 6-week exposure period at 95% relative humidity and either 25°C or 70°C. Greatest corrosion activity was measured on the alloy with higher copper content, AA6111. Higher temperature exposure led to greatly enhanced corrosion activity for AA6111 compared to the lower temperature exposure. The 70°C exposure also led to greater mean corrosion-affected area measurements for the low copper aluminum alloy, AA6022, but the effect was not as stark as that observed for AA6111. Rolling direction affected the propagation direction, and possibly mechanism, of the corrosion effects. Cross-sectional analysis revealed dense corrosion products within the filament, comprising mostly aluminum and oxygen but with traces of chloride and sulphate. Development of varying filament and blister types on a single test panel and the progression of corrosion underneath a filament into the substrate indicate that several corrosion mechanisms can develop on the test panel, testament to the complexity of the corroding surface developed on an aluminum automotive body panel.

Jan 1, 2015

By A. Eslami

When producing high grade mattes in smelter plants, copper losses in the slag are inevitable. Hence, the recovery of copper from slag has been the focus of many research projects, copper flotation being a widely used process. In the Khatoonabad converter, 200 t/d of slag are presently produced with a grade of 2.3% Cu. Assuming a 85% recovery by flotation, about 3.9 t/d copper could be produced, which is of prime importance economically. In the present work, a sample of this slag was crushed and ground in the laboratory to liberate the copper-bearing minerals. Following mineralogical studies, optimum laboratory flotation parameters were obtained, resulting in 90.27 % recovery and 9.42% of copper grade for the rougher stage. At pilot scale, a pulp of 28% solids was floated at ph 10.5 using 40 git of Z6, 25 git of R407 and 20 git of MIBC and A65. A recovery of 83.52% was obtained for a concentrate grade of 28.36% Cu. In the rougher cells, the feed consisted of particles 94% finer than 74 microns whereas in the cleaning stage, particles were 95% finer than 44 microns. Based on the obtained results, the Sarcheshmeh Khatoonabad converter slag is presently being fed to the Chargonbad flotation plant, where a concentrate of 32% copper at 86% recovery is being produced.

Jan 1, 2007

By R. F. Tylecote

"The closure of the iron and steel making plant at Consett in Durham in 1980 marked the end of an era-a long era in the world's iron and steel making history. Iron had been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century.The paper describes sites in the area that first worked the bloomery process and then, in the 16th century, as did most of Europe, graduated to the blast furnace process. The main emphasis is on the early introduction of coal to iron making at the end of the 18th century and the use of the steam engine to render integrated sites possible.IntroductionIron has been smelted in the Tyne-Wear area of the United Kingdom since before the Roman period, but apart from clear evidence of smithing in the Roman period, the historical evidence for iron production on a large scale dates from the 14th century. Like many other countries, the United Kingdom benefitted from the visits of foreign observers, such as Jars, Svedenstierna, de la Houliere and Dufrenoy, who left detailed records. In modern times, information gained from excavations of iron and steel making sites has supplemented the historical record.Natural ResourcesUp to the end of the 19th century, the industry was wholly dependent on its own resources. Iron ore, limestone, wood, coal and water power were all found a short distance away from the main valleys of the Tyne and Wear. The main sources of iron ore were the coal measures, with rider ores from the lead vein s in Alston and Weardale, and carbonate ores from shale horizons in the Carboniferous limestone. Good coking coal was available from West Durham and reasonable coal from the Tyne valley and Northumberland limestone. Limestone was plentiful."

Jan 1, 1983

By J. Worden, D. Hughes, S. Smart, H. Zughbi

The enterprise wide optimization (EWO) of steelmaking and manufacturing is a multi-level, hierarchical problem which spans higher level corporate planning and scheduling through to the lower level operations of processes that produce and manufacture steel. External and internal system dynamics combined with process unit co-ordination create complex changing circumstances for the enterprise. This paper presents a scoping study as a prelude to enterprise wide considerations at an integrated steelworks to help inform the choice of appropriate model types and optimization techniques. The hierarchical, multi-level structure of the enterprise and the important spatial-temporal scales to consider are defined. Insights into the system were gained by analyzing a large set of dynamic operational data. Over two years of data were subject to both univariate and multivariate analysis with the intent of understanding the complex interrelations of energy flows on site, the inherent system dynamics of the energy network, system operational modes, aspects of planning and scheduling and the coordination between major processing units. This analysis was further used to evaluate the performance of the system in regards to energy utilization and understand the potential economic benefits derived from improved operational decisions.

Jan 1, 2015

By M. G. Lipsett

One challenge in applying information technologies in Mining is building a business case. In Mine Maintenance, there is a complex flow of information that contributes to making informed business decisions. By understanding those information relationships and the cost of wrong decisions, analysts can estimate the value of information flow. Developers can then ensure that systems deliver key information in an accurate and timely way. In this paper, general maintenance decision-making is discussed, with examples of how model-based analysis can improve the information delivered to decision makers.

May 1, 2001

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By W. J. Dick

THE purpose of this paper is to point out, briefly, the importance of the coal mining industry of Alberta and to stress the economic factors that hinder its development; also to offer suggestions relating to the major problems of the industry. The minor problems will not be dealt with in detail, because, if the major problems are taken care of, it is felt that the industry itself can take care of ,he remainder. COAL MINING NO LESS IMPORTANT THAN GOLO MINING The large increase in metal mining development in all provinces of Canada, excepting Saskatchewan, Alberta, and the Maritimes, has had the effect of focussing public attention on this branch of the industry. The fact, also, that this development came at a time of depression has been of immense benefit to Canada as a whole. On account of the necessity and consequent demand for gold, with its attendant increase in price, through government action, from $20.67 per ounce to $35.00 per ounce, it is safe to say that the public of Canada have become, today, gold mining conscious. While everyone admits the great value. of the gold mrn111g industry, nevertheless, the equal value to Canada of certain other industries must not be lost sight of. The coal mining industry, in particular, is worthy of greater public and government support than has been accorded it in the past. It would seem unnecessary to stress this matter to a meeting of the Canadian Institute of Mining and Metallurgy, but unless certain facts are brought to your attention, there is danger that the coal mining industry will not be developed to the extent its national importance deserves. Too many public men and men in authority are unaware of the value of coal mining.

Jan 1, 1936

By Limao Zhang

This paper presents a novel model to assess the risk of adjacent buildings in tunnelling environments based on Extended Cloud Model (ECM). ECM is an organic integration of Extension Theory (ET) and Cloud Model (CM), where ET is appropriately employed to flexibly expand the variable range from [0, 1] to (-8, +8), and CM is used to overcome the randomness and fuzziness during the gradation of evaluation factors. The risk level of a specific adjacent building is assessed by the correlation with the cloud models. A confidence indicator ? is proposed to illustrate the rationality and reliability of evaluating results. Ten buildings adjacent to Wuhan Metro Line Two (WMLT) are randomly chosen among hundreds of adjacent buildings for a case study. Results have proved to be consistent with the actual situation. Compared with other traditional evaluation methods, ECM has been verified to be a more competitive solution with high calculation accuracy, wide adaptability, as well as simplified computer programming. There are no stringent requirements on the quantity of training data during the modelling process, and the original data can be directly entered into ECM without a normalization procedure, avoiding the potential information loss. ECM can be offered as a decision support tool for the risk assessment in urban tunnelling construction and worth popularizing in other similar complicated projects.

Aug 1, 2013

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By Q. Li

"The precursor of In2O3 was prepared by hydrolysis precipitation/hydrothermal method using In(NO3)3 solution as the feed material and ammonium hydroxide as the neutralizing agent. The crystallinity, morphology and particle size of the products were characterized by SEM, XRD, BET and LPSA. The results showed that the hydrolysis product consists of an aggregate of cubic In(OH)3 particles with a short rod morphology. In the hydrothermal process, the structure, morphology and size of the particles changes through the mechanisms of Ostwald ripening and phase transition, respectively. When the hydrothermal temperature was less than 280 ?, the Ostwald ripening process took place, which changed the morphology of the particles from short rods to cuboids through dissolution-recrystallization. When the hydrothermal temperature was higher than 280 ?, the processes of Ostwald ripening and phase transition took place successively. Firstly, the morphology of the particles changed from short rods to cuboids through Ostwald ripening, and then, the phase transition from cubic In(OH)3 to orthorhombic InOOH occurred and the morphology of the particles changed from cuboids to polyhedron. INTRODUCTIONDue to its excellent electrical conductivity and optical transparency, indium tin oxide (ITO) film has been wildly used in flat-panel display, solar cell, antistatic coating and EMI shielding (Medvedovski et al., 2008). Indium oxide powder is one of the fundamental materials for preparing ITO film. Along with the development of ITO targets of both high density and large size, high quality indium oxide powders, such as single phase, nano-size, spherical morphology and mono-disperse, have been in high demand (Nakashima and Kumahara, 2002; Betz et al., 2006; Kim et al., 2007). The main preparation methods for indium tin oxide or indium oxide powders include chemical precipitation (Nam et al., 2001; Xu and Yu, 2007), melt atomizing-combustion (Chen et al., 2000) and spray pyrolysis (Ogi et al., 2009). Among them, chemical precipitation has been preferred, since it is simple, easy to control and suitable for industrial scale-up. In chemical precipitation method, indium oxide powders were prepared through the following steps: firstly, indium hydrate precursor was precipitated from an indium salt solution by neutralization using an alkali, such as ammonia; and then, indium oxide (In2O3) powders can be obtained from the precursor through calcination (Li et al., 2006), or solvothermal method (Lee and Choi, 2005), or hydrothermal processing/roasting (Xu et al., 2005; Chen and Li, 2007), respectively. However, the indium oxide powders obtained by direct roasting are polycrystalline, dispersable with a wide size distribution (Liao, 2006). The disadvantages of the solvothermal method are high cost, complicated after-treatment processes, as well as bad performances of the powders (Udawatte and Yanagisawa, 2000). Therefore, among three methods of obtaining indium oxide from the hydrolysis precursor, the hydrothermal process/roasting method is the most feasible to synthesize high quality In2O3 powder with uniform crystallinity and size (Kim et al., 2002; Zhu et al., 2004; Xu et al., 2005; Xu et al., 2005; Chen and Li, 2007; Seetha et al., 2009). However, current research on hydrothermal process-roasting method has been limited to the synthesis of a certain ITO or In2O3 powders under specific conditions. A systematic study on the phase transition, as well as the change of the morphology and size of the particles in the hydrothermal process is still missing. In this paper, the effects of hydrothermal processing on the mineralogy, morphology and size of products were investigated. The results showed that the evolution of crystal structure, morphology and size in the hydrothermal process was affected through the mechanisms of Ostwald ripening and phase transition successively. These results are novel and have guidance for improving the hydrothermal process for In2O3"

Jan 1, 2012

By M. Tanaka, T. Oishi, K. Koyama, S. Alam

"A novel hydrometallurgical process for copper recovery from waste printed circuit boards has been proposed, which consists of selective leaching of copper metal as Cu(I) by Cu(II) in ammoniacal alkaline solution, purification, and electrowinning. The distinct feature of this process is much lower power consumption during the electrowinning than that during the conventional one from acidic copper sulfate media, because the deposition of copper metal from Cu(I) at the cathode and the oxidation of Cu(I) to Cu(II) at the anode take place in the present method. In the laboratory-scale tests using waste printed circuit boards, high purity copper which contains 1.1ppm of impurities was obtained in a chloride system. INTRODUCTIONThe recovery of various metals from waste materials is an important issue in order to conserve the environment and metal resources. Copper is used for cables, electric appliances, etc., and is currently a very important material for industries and will continue to be in the future. Among the wastes that contain copper, one of the most complex recycling materials is electronic scrap like printed circuit boards (PCB), which generally contain 10-30% copper as well as plastics, fibreglass and other metals. There are two ways to recover copper, either pyrometallurgical or hydrometallurgical. Hydrometallurgical treatments generally have more flexibilities in the process scale and control. The separation processes tend to become complicated because of the poor selectivity during the leaching in the sulphuric and hydrochloric acid media. On the other hand, the use of ammonia as a complexing agent, gave a higher selectivity for copper leaching (Nigo, Majima, Hirato, Awakura, & Iwai, 1993; Majima, Nigo, Hirato, Awakura, & Iwai, 1993; Zhou, Shinme, & Anezaki, 1995; Koyama, Tanaka, & Lee, 2006) .In this study, recycling process containing leaching, copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) is introduced. Furthermore, copper recovery from a waste printed circuit boards and impurity behaviour was examined in ammonia-ammonium sulfate (sulfate system) and ammonia-ammonium chloride (chloride system) systems."

Jan 1, 2012

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By Steven Doyle

Presentation Outline ?Introduction to Brunswick Mine ?Mining Needs and Drilling Trends ?Maintenance Program ?Back to Basics ?Results ?Additional benefits Introduction Xstrata Zinc Brunswick Mine ?No. 12 deposit discovered in 1953, pilot mining 1957, u/g mining began in 1964 ?Zinc, copper, lead and bulk lead/zinc concentrates ?Since 2007, a fully owned division of Xstrata Zinc Canada ?Over 132Mt milled 3.4 % Pb, 8.8 % Zn and 102 g/t Ag ?Deposit dips approximately 70 degrees; strike length of 1200 m; currently mining from 250 m to 1125 m depth

Nov 1, 2011

By M. D. Everell

Le Centre de Recherches minérales (CRM), qui est un organisme de recherche appliquée du ministère de l'Energie et des Ressources du Québec, a été créé en 1969, dans le but de procurer un support scientifique et technique à l'industrie dans le domaine des mines et de la métallurgie. Pour atteindre ses objectifs, le CRM met à la disposition de l'industrie un personnel spécialisé et compétent dont une quarantaine d'ingénieurs et de scientifiques. Etant donné la nature même de l'industrie minérale, ce personnel est très versé dans l'étude des problèmes diversifiés des domaines de la technologie minière, du traitement des minerais, de la métallurgie extractive et de l'analyse minérale. Ce Centre de recherches met également à la disposition de l'industrie une usine-pilote permettant de reproduire les résultats du laboratoire au moyen d'un appareillage de type industriel, d'obtenir des échantillons en quantité suffisante pour une exploration du marché et de familiariser du personnel avec les opérations normales de l'industrie. Certaines de ses contributions récentes au développement de l'industrie minérale du Québec seront présentées.

Jan 1, 1985