Search Documents

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By M. G. Ayat

Although other methods of mineral concentration have been developed over the years, gravity separation remains one of the most efficient and economical for cleaning coal. The concentrating table and the spiral separator are popular devices used for the separation of minerals by exploiting the differences in specific gravities of the product material and the gangue. While the former device has been servicing the coal industry for over 75 years, the latter seems to have not been employed extensively for coal cleaning purposes in this country. As far as coal preparation is concerned, both separatory devices seem to be most efficient for intermediate to fine size fractions. As it stands there exists a great deal of confusion amongst preparation engineers and plant managers as to whether spirals can have a place in the coal industry. If so, whether their come back is the beginning of the end for concentrating tables, or can they be employed along with concentrating tables to contribute toward more efficient cleaning processes resulting in an improvement in the overall economics of the coal preparation industry. This paper examines the efficiency of both systems for coal processing operations as well as the basic principles, operational variables, economics, advantages and disadvantages associated with each unit operation. Attempts have been made to draw conclusions and make recommendations as to which system would be more beneficial for coals of known characteristics.

Jan 1, 1986

By Chris Lynagh, Collin Schroeder

Determining the best excavation method is a critical step in successful tunnel construction. In rock tunneling, several factors can dictate the excavation method, such as: (1) rock characteristics, (2) tunnel size and length, (3) nearby utilities/infrastructure, and (4) contractor’s preferred means and methods. This paper discusses the various rock tunnel excavation methods utilized on the Doan Valley Storage Tunnel Project (DVT), a project constructed as part of the broader Project Clean Lake in Cleveland, Ohio. The differences between each method’s initial and final lining, geology, and cycle sequence will be analyzed and compared.

Jun 13, 2023

By J. Platt

Recent EPRI research on utilities? likely strategies to reduce sulfur emissions differs sharply from policy analyses showing all- switching or all-scrubbing choices. Energy Ventures Analysis, with Stearns-Catalytic and A. T. Kearney, estimated sulfur-removal costs for scrubbing or switching at virtually all affected plants in the 31 Eastern States. Cost tradeoffs occur between $30 and $40-plus per ton FOB mine in Central Appalachia ($33-44-plus per tonne). 1/2 to 3/4 of total sulfur reductions comes from scrubbing, whose costs act as a cap on low-sulfur coal prices. In a severe environmental scenario, low- sulfur coal demand evaporates, replaced by very low-sulfur (0.7%) coal demand. Additional findings and implications of EPRI coal supply and market studies will be reviewed.

Jan 1, 1987

By Edmund C. Bitzer

The unit costs of dry crushing, within the efficient reduction ranges of equipment now available, are considerably less than those for the reduction of the same material in the same size range by wet mills using grinding media. This is a commonly recognized fact which cannot be disputed; still we find considerable imbalance in costs between the crushing and grinding sections of many operating mills. In other words, there are many instances where more reduction could be accomplished in the lower cost area of dry crushing. In addition, equipment is now available which enlarges this area and makes it possible to consider much finer crushing than has been heretofore economically feasible. There has been a tendency for the past two decades to utilize wet rod-¬milling in the reduction step. This actually amounts to a fourth stage of crushing in a size range formerly served by roll crushers which have fallen from favor on account of high operating costs, Some investigations have indicated that there is not sufficient difference in the operating costs of rolls and rod-mills to give a clear cut advantage to either method, There has for some time been a need and an opportunity for a dry crushing process to improve costs in the range now served by these two systems.

Jan 1, 1965

By M. G. Hester

The ore reserve modeling of stratiform uranium deposits to be mined by selective underground mining methods must be done with consideration of the erratic nature of the ore forming processes that produced the mineralization. Estimation methods that model the uranium grade as a smooth transition between high grade and low grade drillhole intercepts tend to greatly overestimate the ore tonnage. Care must be taken to first establish realistic ore pod geometries and then estimate the grade of the reserve units within the pods.

Jan 1, 1985

By W. J. Martin

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time ten pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause the chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1986

By George A. Savanick

The objective of this paper is to review advances in the art of borehole (slurry) mining made by the Bureau of Mines. The introduction gives historical and general background information on borehole mining. The borehole mining concept is defined and justified in terms of economics, health and safety, the environment, and resource conservation. This is followed by a description of the design of a prototype borehole mining tool (BMT) developed by the Bureau of Mines. Included are design drawings and performance specifications. The next section describes the application of the BMT in the extraction of metallurgical coal from steeply pitching seams near Wilkeson, Wash., during 1975-76. The field test showed that the BMT produced coal at the rate of 8 tons per hour (tph) (7,272 kg/hr) from a depth of 88 feet (26.8 m) and was effective in producing coal as far as 15 feet (4.6 m) from the center of the borehole. The data are used as a basis for an economic analysis of borehole coal mining and for the suggestions for the design of a second-generation borehole coal mining tool. The following section describes Bureau efforts in applying borehole mining to the extraction of uraniferous sandstone at Rocky Mountain Energy Corp.'s Nine-Mile Lake site, Natrona County, Wyo. BMT design changes appropriate to uranium mining are described along with production, reliability, and reclamation data taken during 1977-73. The field test revealed that the BMT produced 900 tons (81.8x105 g) of uraniferous sand at an average race of 8 tph (7,272 kg/hr) from a depth of 75 (22.8 m) to 90 (27.4 m) feet and created a cavity 25 feet (7.6 m) in radius. These data are used as the basis for an economic analysis of borehole mining of shallow uraniferous sandstones. Reclamation data included will be the results of backfilling experiments conducted at Nine-Mile Lake during 1978. The most significant of these data were that backfill was emplaced at the rate of 16 tph (14.5x103 kg/hr) and that 90 percent of the material extracted from a cavity can be backfilled.

Jan 1, 1979

By D. Mannino, M. Townsend, E. Daniloff, E. Petsonk

Nonspecific airway hyperresponsiveness is a central feature of chronic obstructive pulmonary disease and has been associated with atopy in the presence of environmental exposures such as smoking. Coal miners may develop emphysema and lung function decrements related to their dust exposure. To investigate the roles of airway responsiveness and atopy in these effects, we evaluated the relationships among smoking, a history of hay fever or seasonal rhinitis, and airway responsiveness (AR) in a group of underground bituminous coal miners and nonmining controls. All subjects had a normal baseline percent predicted FEV1. Increased airway responsiveness was defined as a 15% or greater decrease in FEV1 following methacholine inhalation. 85 miners (45%) and 99 controls (46%) were current smokers, 59 miners (31%) and 55 controls (26%) were lifetime nonsmokers; former smokers were excluded from further analysis. Overall, 25% of 144 miners included in this analysis had increased AR, as opposed to 29% of 155 controls. Thirty-seven percent of both miners and controls had a history of seasonal rhinitis. Significantly fewer miners (15%) had a history of hay fever compared to controls (25%, p< 0.05). Figure 1 shows the prevalence of increased airway responsiveness in miners and controls in association with hay fever. In both smoking and non smoking miners the presence of a hay fever history was significantly (p < 0.05) associated with a higher prevalence of increased AR. Little effect was seen in smoking (p = 0.827) and nonsmoking (p = 0.940) controls. Figure 2 shows a similar higher prevalence of increased AR associated with symptoms of seasonal rhinitis in the mining group. This was significant (p < 0.01) only in the smoking miners. No effect was noted in the controls. These data suggest that the association of a history of hay fever or seasonal rhinitis symptoms with increased airway responsiveness may be more common in coal mining, compared to non-dusty occupations. Although the implication of these data are unclear, further study of miners with a history of hay fever or seasonal rhinitis is warranted. (Supported in part by Grants G1135142 and G1105142, US Bureau of Mines, Generic Mineral Technology Center for Respirable Dust)

Jan 1, 1991

By Yasutaka Izumi, Tuneyoshi Funasaki, Keizou Miki, Makoto Kanai

INTRODUCTION The Tokyo metropolitan region, inclusive of the three neighboring prefectures (Kanagawa, Chiba and Saitama), has the highest concentration of population and industry in Japan; with an area of 13,500 km2 or only 3.6 percent of the national land, but a population of 31.8 million or 26 percent of the national total, and a Gross Regional Product (GRP) of146 trillion yen (US$1.33 trillion) or 36 percent of the overall GDP of Japan as of 1990. Tokyo Bay, embraced by the metropolitan region as shown in Figure 1 (a), (b), is open to the Pacific Ocean as a marine gateway and is ringed by large cities and coastal industrial zones together with port facilities, all constituting a concentration of prime importance for socio-economic activities. The Trans-Tokyo Bay Highway (TTB highway), which crosses Tokyo Bay and provides a direct transportation link between the west and east sides of the bay, has long been a sort of “dream-come-true” project in Japan. As shown in Figure 2, linked to the Tokyo Bay Shore Highway, Metropolitan Inter-city Expressway, Tokyo Outer Ring Road, Tateyama Express-way, and others, it will play an important role as an integral part of the regional highway network to help promote spatial redistribution and multi polarization of urban functions, thus strengthening cooperation between cities and restructuring the metropolitan region. The TTB Highway is a project of 15.1 km in length designed as a toll highway to cross the bay by tunnel and bridge, and will require ten years to complete at a total cost of more than 1,438 billion yen (US$13.077 billion). Following more than 20 years of feasibility and environmental assessment studies, construction of this giant offshore highway project commenced in May 1989 as the first large-scale highway project with private-sector participation under the prevailing Road Law in Japan, and is now steadily proceeding toward the goal of completion in fiscal1997. This report outlines the entire TTB Highway project, including the waterproofing measures against high water pressure and the rapid construction method applied in the construction of shield tunnel sections.

Jan 1, 1997

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.&apos;s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By A. E. Foscolos

British Petroleum (BP, 2005), indicates that world reserves for oil to be 1198 billion barrels, for natural gas the equivalent of 1156 billion barrels of oil and for coal the equivalent of 3219 billion barrels of oil. If we take into consideration the mean aver-age annual increase in demand of the last three years for oil, 2.6%, for natural gas, 3.9%, and for coal, 6.6%, then their respective reserves? lifespan are calculated to be 27, 34 and 38 years. Without taking into account their annual increase in demand, lifespan increases to 38, 67 and 161 years respectively. Since zero increase or perpetual increase in energy demands on finite resources is unrealistic the selection of the most suitable energy commodity for power generation rests upon the law of supply and demand of each commodity. This defines its price hence its selection for the production of cheap electricity. When the ratio of supply to demand is less than one, peak production is achieved. Any further increase in demand results in price increase to quench its demand. The Association for Oil and Gas Peak (ASPO) has calculated that when oil demand exceeds 84 million barrels/day, Peak Oil Production will be attained thus prices will start to increase in order to even demand with supply. Correspondingly, Gas Peak Production is expected to take place when demand exceeds 9.1 or 10.2 billion cubic meters/day. Peak Oil production has been calculated to take place in the current year, 2006, while Gas Peak production is estimated to take place between 2020 and 2025 provided that gas will not cover the energy deficit created from the lack of oil otherwise Gas Peak production could arrive as early as 2010. The use of coal for power generation is considered a better alternative than oil and gas if new combustion technologies with an energy efficiency of 43%, Germany, and 47%, Denmark, are adopted. These not only extend the lifespan of coal reserves but reduce also CO2 emissions by 25% and 31%, respectively. In the very near future CO2 sequestration and fixation in deep geological strata will eliminate its emissions thus rendering the use of coal the cheapest feedstock for power generation.

Jan 1, 2006

By Ellen Amoako Afful, Michael Moats, Guang Xu, Ashish Kakoria

Electrowinning and solvent extraction are crucial steps in the production of high-purity copper. However, safety concerns have been raised regarding the acid mist generated from the electrowinning process. The mist generated results in health risks to workers and damage to machinery and infrastructure. Currently, chemicals and pellets are used to control acid mist. However, the effectiveness of these controls may vary depending on the type of organic solvent used in the solvent extraction process, which can influence the generation of acid mist. This study aims to evaluate the impacts of organic solvents and surfactants on acid mist suppression. In this study, an electrolyte is contacted with organic solvents to simulate the solvent extraction. The electrolyte is dosed with 20 mg/L of surfactant at each contact. Acid mist testing is performed on the electrolyte separated from the organic phase at the end of the solvent extraction step. The mist collected is analyzed to determine the level of acid mist generated. The results of this study indicate that organic solvents and surfactants showed significant acid mist suppression, but with somewhat different suppression efficiencies. After first contact, Licorice and the organic, for instance, showed a suppression efficiency of up to 69.7% but its efficiency gradually decreased as the number of contacts increased.

Feb 1, 2025

By Colonel Oattis E. Parks

The quantity of coal recovered by diamond coring techniques is not sufficient in many instances to make meaningful coking and/or ash fouling tests. Quantities in excess of that obtained by conventional coring techniques, usually in amounts exceeding 500 pounds, has been designated bulk sampling. During the past three years, AMAX Coal Company has utilized five methods of bulk sampling. It was our desire to obtain a bulk sample that was diagnostic of the seam by the most expedient and economical method. From the beginning all of our efforts have been directed to methods which would extract the required coal from slim boreholes which provide quick and inexpensive access to the coal seam, regardless of depth, terrain and accessability. In our efforts and investigation several large diameter cores have been taken from thick coal seams at relatively shallow depths in easily drilled rocks. On the other hand, for deeper thin seams multiple large diameter coring is more expensive and time consuming. It is somewhat less expensive when multiple cores are taken from a single slim borehole utilizing deflection coring, although considerable skill is necessary.

Jan 1, 1973

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By E. Ashworth

A thermistor probe has been developed to measure in situ temperature profiles underground. A full description of the probe is given. Data collected from the probe has been used to compare the actual profiles with those predicted from a finite element analysis using laboratory measured thermal properties of the different rock types. This comparison indicates the applicability of laboratory measured parameters in modeling the real conditions. Factors such as applied pressure, moisture content and anisotropy on laboratory measurements is discussed.

Jan 1, 1983

By Allan M. Harvey

Asbestos production in the United States is no match for the vast operations of Canada and the U.S.S.R. The majority of U.S. production is limited to the states of Vermont, California and Arizona, and the type of asbestos is limited to the variety of serpentine known as chrysotile. What little production of other varieties of asbestos such as tremolite and anthophyllite that has occurred over the past 100 years since asbestos became a useful commodity is of practically no significance. However, new developments in the field of environmental and occupational health hazards has startled the mining industry in this country and has already given a few particular companies reason to be concerned about the profitability and probability of their continued operation in the business of mineral processing. At the heart of these developments is the question and controversy over just what constitutes asbestos and what exactly is the definition of a fiber. To the mineralogist or, in fact, to practically anyone engaged in the process of mining and separating minerals there is little or no question about asbestos. It is not a distinct mineral but rather a commercial product serving specific applications for which a number of fibrous mineral types can qualify. To the hygienist pr health authority this definition is too general. They demand something they can detect, measure and control. To suit their purposes and simplify their task of detection, they have labelled the minerals chrysotile, crocidolite, amosite, tremolite, anthoph-yllite and actinolite as asbestos, and any particle of these minerals with an aspect ratio of 3:1 as an asbestos fiber. It does not

Jan 1, 1976