Search Documents

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By S. M. Molloy

The postwar demand for insulating material such as mineral wool, in-creased in proportion to the rapid construction of new buildings, placing an enormous burden on the existing mineral-wool industry both in known sources of raw materials and in available plant facilities. In view of the increased demand on the industry, the Bureau of Mines in its Mississippi Valley Experiment Station" Rolla, Mo., undertook an investigation to aid the industry by establishing resources of raw materials through actual laboratory wool-blowing tests and by developing certain methods for evaluating the physical proper-ties of a mineral wool. As material was received from the public, laboratory-evaluation technique had to be developed, the results of which would reflect in the mineral-wool-industry standards. The methods of testing used by the mineral-wool industry, not only would have required a pilot-plant installation capable of producing a large tonnage of mineral wool, but each wool-blowing campaign would have been very expensive and necessitated considerable personnel and equipment. The present laboratory wool-blowing equipment can produce as high as eight wool-blowing campaigns a day. The nature, simplicity, and size of the physical testing equipment permit testing as small a sample of wool as 25 grams and give information as reasonably accurate as in a 40-pound bag of wool. The purpose of this report is to describe the laboratory method of production and the evaluation of the physical properties of small quantities of mineral wool. Considerable work has already been done, and the interest of the public and industry is measured in the number of samples being submitted for testing.

Jan 1, 1948

By H. Kenworthy

The objective of this research was to develop methods and determine conditions under which metallic sulfides with lower boiling points than sphalerite may be removed from zinc sulfide concentrates by volatilization. A higher percentage of extraction of lead, cadmium, and germanium than is common in current practice was sought. The investigation, conducted by the Metallurgical Branch of the Minerals Technology Division, Region VI, showed that, under proper conditions, it is possible to remove over 90 percent of the lead, cadmium and germanium as an enriched sublimate. The uses of lead, and cadmium to a lesser extent, are well-known. Although germanium was discovered in 1886 by C. Winkler, commercial use has been achieved only in recent years. The amount consumed per manufacturer unit is so small that the price of germanium may still be quoted by the gram. The electronic industries have been the chief consumer of this semiconductor. Germanium is sold largely to the fabricator as a dioxide for reduction to metal and subsequent processing into wafers for use in diode and triode electronic tubes. Extensive research at Purdue University during World War II led to the first practical use of germanium.

Jan 1, 1952

By N. P. Gallagher

The U.S. Bureau of Mines investigated a hydrothermal sulfidation (HTS) and chloride leaching procedure to recover lead and silver from plumbojarosite. The plumbojarosite, generated during pressure-oxidative leaching of zinc concentrate in a commercial operation, contained, in percent, 25.4 Pb, 18.8 Fe, 1.4 Zn, 29.5 sulfate (S042.), 3.2 elemental sulfur (SO), 13.4 total S, and 7.4 tr oz/st Ag. The HTS was conducted in an autoclave and converted the plumbojarosite into amorphous iron oxide and liberated the Pb and Ag as sulfides (S2) The best operating conditions were 50 g of plumbojarosite and 7 pct So (2.04 g So added) in 500 mL of 2.0-mol/L NH3 at 150° C for 1 h. The sulfidation product contained, in percent, 37 Pb, 28 Fe, 2 S042., 7 total S, and 11.2 tr oz/st Ag. Flotation of the sulfidation product was conducted at pH 3 with 15-pct pulp density and 2.4lb/st of isopropyl xanthate as collector. The flotation concentrate contained 43 pct Pb, 25 pct Fe, and 13 tr oz/st Ag. FeCl3 leaching of the sulfidation product in a resin kettle extracted 98 pct Pb and 97 pct Ag from the sulfidation product, and HCI-Oz leaching in a shaker glass bottle extracted 99 pct Pb and 98 pct Ag. Both leach residues met the Environmental Protection Agency's Toxicity Characteristic Leaching Procedure (EPA-TCLP) standards for nonhazardous wastes. The HTS and chloride leaching procedure is a potentially effective method for detoxification of plumbojarosite-bearing residue from the zinc pressure-leaching circuit.

Jan 1, 1989

By Maria I. De Rosa

Combustible materials, when burned, produce toxic gases and smoke, which may vary dramatically from one material to another, with resultant different total toxicity and smoke obscuration levels. This U.S. Bureau of Mines report presents smoke property data acquired for a variety of mine combustibles and shows that there exists a correlation between the smoke properties, the relative toxicity, and the smoke obscuration levels of those combustibles tested. These correlations can be used to devise simple, standard tests for determining the toxic and smoke obscuration hazards of mine materials during fire.

Jan 1, 1989

By S. H. Ash

The United States Bureau of Mines has published relatively little on the flooding and unwatering of coal and metal mines. Bulletin 229, Fifty-Nine Coal-Mine Fires, published in 1927, contains several instances of the flooding of mines or sections thereof to extinguish fires but does not describe their unwatering. Report of Investigations 2649, Explosion Hazards Incidental to Unwatering Coal Mines, published in 1924, warned against the possibility of gas accumulations in flooded mines and indicated the precautions to be taken. Report of Investigations 2255, An Unusual Hazard in Reopening Long-Flooded Timbered Metal Mines, published in 1921, told of methane being pocketed and the danger thereof. The flooding of mines originates in many ways. At some mines flooding followed reopening after what was thought to be permanent abandonment; also, explosions have caused some mines to be flooded. Extinguishing fires, accidental encountering of underground streams or flooded old workings, and caves of strata admitting water from underground workings, water-bearing strata, or surface accumulations have also flooded all or parts of mines. Unfortunately, un watering often necessitates much study and causes apprehension largely because experiences in similar situations are not generally known, as few descriptions of successful or unsuccessful methods are available. The job has sometimes been contracted for outside the local management involved and has become a matter of record for the contractor only. As the cost-plus contract system often employed in the past is now known to be expensive, careful managements elect to handle the problem themselves, in line with the general policy of cutting expense where possible. This report describes specific in-stances of successful unwatering by operators.

Jan 1, 1933

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By James E. Mauser

This report deals with the investigation of a continuous process for producing pure zirconium. It covers the construction, operation, and maintenance of the semicontinuous reactor. The report covers a study of test variables, such as reactor temperature and reluctant charge weights, and evaluates the results, such as billet metal hardness, residual billet salt content, and suitability of a purified billet as a consumable electrode for arc melting. The purpose of this project was to develop an inexpensive and continuous process for producing pure zirconium. The process developed, termed the semicontinuous reactor process, produced billets of compacted zirconium sponge. The metal was produced by reducing zirconium tetrachloride with sodium and magnesium beneath molten byproduct salt. Hydraulic rams at each end of a vertical reaction tube compacted the sponge and ejected it as a billet. These billets were purified by heat under vacuum to remove entrapped salt. The goal was to utilize the purified billet directly as a consumable electrode for arc melting.

Jan 1, 1961

By Charles Vaught

The U.S. Bureau of Mines evaluated the self-contained self-rescuer (SCSR) donning proficiency of 243 miners. These workers were from eight underground coal mines in the eastern United States. The objectives of the study were (1) to gather information on skill levels, since all miners in the study had prior instruction and opportunity to practice donning the apparatus, and (2) to summarize a quality control procedure useful in conducting periodic evaluations of donning proficiency. The sampling procedure used proved to be both reasonable and efficient in gathering information on training effectiveness. It also provided a good statistical base for making informed site-specific decisions regarding SCSR training needs. Results from the observed samples at each of the eight mines indicate a wide variability across sites. The rate at which miners failed to isolate their lungs varied from 3.3 to 40.0 pet. Concomitantly, proficiency rates (miners either performing adequately or demonstrating a perfect 3 + 3 sequence) ranged from 13.3 to 63.3 pet.

Jan 1, 2010

By Deno M. Pappas

The objective of this Bureau of Mines investigation was to identlfy and evaluate alternative binder materials for use in stabilizing and consolidating highly fractured roof along longwall faces and gate roads. The desirable characteristics of a stabilization material were defined, and an extensive search was conducted to find materials satisfying these characteristics. Of 20 materials originally scrutinized, 9 were chosen for laboratory analyses. The laboratory tests evaluated bond strength and tensile strength under both dry and wet conditions. An optimum material was not found. The laboratory analyses indicated two possible candidate materials for longwall stabilization: high-aluminous cement and two-component epoxy; however, the tensile strength of the high-aluminous cement was mediocre, and the epoxy cement is toxic, flammable, and fairly expensive. The potential market demand for an effective and economical stabilization macerial is discussed in the appendix.

Jan 1, 1988

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By Martin H. Stanezyk

The Bureau of Mines investigated leaching of selected copper sulfide minerals and a composite of impure flotation concentrates at elevated temperatures and pressures with ammoniacal solutions. Copper 1 (tractions of 96 percent were obtained by leaching chalcopyrite at 75° C under oxidizing conditions for 60 minutes. An extraction of 99 percent of the copper contained in the composite concentrate was obtained by leaching the product for 90 minutes at 75° C. In tests of bornite, chalcocite, and covellite, 90 to 97 percent of the copper was extracted at 20° C provided an 8-hour reaction period was used. At 75° C essentially complete dissolution of the copper from these three minerals was accomplished in 60 minutes. Additions of ammonium sulfate to the leach solutions were required to obtain high-percentage extractions of the copper from bornite, chalcocite, and covellite. Although ammonium sulfate was not required when digesting chalcopyrite, copper extraction was enhanced and less free ammonia was required when ammonium sulfate was added to the leach pulps. The chemistry of leaching copper minerals was studied. It was C, termined that chalcocite altered to covellite as one step in the dissolution When leaching iron-bearing copper sulfides, hydrated iron oxide formed on the mineral surfaces, indicating that a diffusion process prevailed. No evidence of covellite was detected.

Jan 1, 1966

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006

By Richard G. Burdick

The Bureau of Mines conducted this research to determine the feasibility of using soil redox measurements, a relatively new method in mining geophysics, to locate or define a variety of conditions that are hazardous or otherwise of interest to the mining industry. The method was used in three widely separated areas in an attempt to de- fine subsurface concentrations of methane, the edges of coal-burn areas, and a hydrothermal vein set. Both a description of the method used and test cases are given in this report.

Jan 1, 1982

By Elizabeth G. Baglin

Research was conducted by the Bureau of Mines to determine the feasibility of using electrokinetic densification to dewater Bayer process red mud, magnetic black mud prepared by pressure digestion of red mud in the presence of ferrous sulfate, and magnetic black mud formed by simu-lated Bayer digestion of Jamaican bauxite with added ferrous sulfate. Tests showed that the solids content of presettled muds could be increased from 25 pct to approximately 40 to 48 pct by gravity draining followed by electrodewatering for approximately 48 h. Electrodewatering may not be practical because of increased reagent and processing costs and because the muds must be thoroughly washed prior to electrodewatering to remove dissolved ions and decrease mud conductivities.

Jan 1, 1988

By J. D. Zetterstrom

This report supplements an earlier publication on lightweight aggregates of North and South Dakota.3/ The purpose of the investigation was (1) to study the expansion characteristics of large samples of Dakota clays and shales in a 12-inch by 15-foot rotary kiln; and (2) to improve the laboratory bloating test as a tool for predicting the suitability of samples for the rotary-kiln process. This was done by comparing results of the laboratory and kiln tests.

Jan 1, 1956

By C. S. ROBINSON, T. M. Romslo

This investigation was conducted jointly by the Bureau of Mines and the Geological Survey to obtain further information on the source and economic possibilities of the copper mineralization exposed on the Copper Giant group of claims, Ajo mining district, Pima County, Ariz. The Copper Giant group of claims was first brought to the attention of the Bureau of Mines by Joseph Hunter (deceased), Phoenix, Ariz., part owner of the claims. In December 1942 these claims, and an adjoining group, were investigated by T. C. Denton, mining engineer, formerly with the Bureau of Mines, and Nels P. Peterson, geologist, Federal Geological Survey. It was concluded the area could not be considered as a source of copper for immed- iate emergency needs and that further investigation of the area, at the time, was not warranted. In the spring of 1948 the lessee, J. H. Greenway Albert, requested Bureau of Mines assistance in developing the property. J. H. Hedges, former chief, Tucson Branch, Mining Division, and Lincoln A. Stewart, mining engineer, Bureau of Mines, made a cursory examination of the property and noted that at numerous places, low-grade copper mineralization appeared on fractures and bedding of the Locomotive fanglomerate and Ajo volcanics, which are thought to be of Tertiary age. During the period of May 11 through 14, 1949, Bureau of Mines engineers3 mapped and sampled two areas of mineral- ization. On June 2 and 3, 1949, the areas selected by the Bureau and three other nearby mineralized areas were investigated by C. A. Anderson and R. S. Cannon, Jr., of the Federal Geological Survey. As a result of these examina- tions, further investigation of certain areas was believed to be merited. The Copper Giant area was selected as the most favorable in which to carry out exploratory and development work. The field work on the project was started in October 1949 and completed in December 1949. It consisted of road building, trenching, sampling, topo- graphic and geologic mapping, diamond drilling, and logging of core. Samples taken on the project and during preliminary examinations totaled 64, of which 63 were surface samples. Diamond drilling, started October 10 and completed December 7, consisted of two holes for a total depth of 1,542 feet.

Mar 1, 1952

By D. R. Corson

The Bureau of Mines instrumented two similarly backfilled stopes--one filled in the normal manner and the other with the fill densified using vibratory compactors--to evaluate the effect of fill compaction on subsequent vein-wall closure proposed as a adjunct process for strengthening cemented fill. Hydraulic pressure cells to monitor pressures within the fill and mechanical closure devices to measure vein-wall movement and the procedure for their installation are described. The field compaction work was generally performed manually by utilizing small commercial concrete vibrators. A prototype immersible vibrator using slusher cables to propel the vibrator in the stope was used on several lifts of fill. Although compaction efforts were less effective than anticipated in increasing the final density of fill, analysis of the field data does indicate somewhat improved strain characteristics and an increased pressure buildup for the densified fill. The effects of a prolonged period of inactivity and of rock burst occurrences in the immediate area are also reflected in plots of strain and pressure within the two instrumented stopes.

Jan 1, 1971

By Nabil A. Bibawy

The U.S. Bureau of Mines has established a method for the calibration of class 2 and class 4 standards of mass using a procedure from designs developed by the National Institute of Standards and Technology (NIST). This method produces a weight calibration that is within 1.0 pct of the balance sensitivity. A set of four 1-kg weights yielded a standard deviation of 3.25 mg compared to ±2.91 mg balance sensitivity. The method employs the use of a high-accuracy balance to measure the difference between a set of weights calibrated by NIST and the set to be calibrated. The error of the balance is included in the error for each weight calibrated.

Jan 1, 1989

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988