Search Documents

By A. McLean, A. Hue, K. Le, Y. D. Yang, P. Wu

While the treatment of relatively inexpensive ferrosilicon alloys is a potential refining route in order to generate solar grade silicon, phosphorus is one of the more difficult impurities to remove by conventional processing. In this project, the use of an electromagnetic levitation technique was used to investigate the dephosphorization of ferrosilicon alloy droplets exposed for various times and temperatures to a hydrogen-argon gas mixture. It was found that approximately 40% of the phosphorus was removed from an 85%Si-15%Fe alloy after 20 minutes exposure at approximately 1673K, to a gas mixture containing 48.5% hydrogen. Further dephosphorization is expected with longer reaction times. The effect of increasing temperature was found to be insignificant, although processing at lower temperatures is not only economically advantageous, it also decreases evaporative silicon losses, thus resulting in a more efficient process.

Jan 1, 2015

By C. S. Ha, H. S. Choi, D. Y. Shin

POSCO installed a new 100 ton oxygen bottom-blown converter in 2013 for the development of new steelmaking process named as PS-BOP which is reading POSCO-Saarstahl Basic Oxygen Process. This process was developed by the collaboration research between POSCO and Saarstahl AG in Germany that is based on substantial increase of CO post combustion in a converter by blowing hot air from the top of converter. The collaboration research has been finished successfully in November 2013 with 17% decrease in hot metal ratio (HMR) when hot air was blown from the top of the oxygen bottom-blown converter. After the collaboration research the converter has been tried to be operated as oxygen top and bottom-blown converter to reduce bottom wear and to decrease production cost with increased use of low cost Fe source by the help of increased CO post combustion. The presentation includes experience on the start up of oxygen bottom-blown converter, HMR reduction trials with hot air top blowing and transition from oxygen bottom-blown to top and bottom-blown converter operation.

Jan 1, 2015

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By M. Kosugi, Y. Kon, M. Kawata, J. V. Satur, K. Mitsuhashi, C. Tokoro, K. Horiuchi, R. Kawarabuki, B. Calabia

"Liberation of copper minerals is important in ensuring high flotation efficiency in copper sulfide flotation. The high pressure grinding roll (HPGR), microwave (MW), and electric disintegration (ED) are known to feature enhanced liberation over conventional comminution machines such as jaw crushers and ball mills by producing internal stresses on minerals or mineral grain boundaries through high compressive forces, thermal expansion of minerals, and pulsed high voltage discharges, respectively. In this study, each of these methods was applied before ball mill grinding to investigate its effect on enhancing the liberation of copper minerals in a low grade and fine-grained copper ore. The copper minerals observed in the tested ore sample are bornite, chalcocite, and chalcopyrite, and their grain sizes range from 10 to over 100 µm. Calcite, quartz, and feldsparare confirmed as gangue minerals. The liberation of the copper minerals by the different methods was analyzed using the mineral liberation analyzer (MLA) and compared. The result showed that the HPGR crushing was the most effective for enhancing copper mineral liberation. HPGR bench-scale test was then conducted on the copper ore and flotation was applied on a HPGR-treated sample to confirm the improvement in the flotation performance by applying HPGR.INTRODUCTIONIn order to recover copper minerals by flotation, copper ore is usually ground by ball milling to liberate the copper minerals from gangue minerals. In the case that the fine size copper minerals are targeted, grinding of the copper ore to a finer size is necessary to increase the copper recovery. However, finer size grinding by ball mill increases energy consumption significantly, which might deteriorate the economies of the mineral processing operation. HPGR, MW, and ED have been recently the focus of researchers as new techniques for enhancing the mineral liberation in mineral processing (Tavares, 2004; Kingman, 1998; Wang, 2010).HPGR crushing is considered to generate micro cracks along mineral boundary when rocks pass between two rolls by applying high compressive force. In the MW treatment, micro cracks are reported to be generated at crystal boundaries by differential thermal expansion of crystals attached to each other. In the ED treatment, micro cracks are known to be produced by plasma current flowing along mineral grain boundaries. These treatments are expected to increase mineral liberation (Fujita, 2001),improve flotation performance(Michaelis, 2005), and reduce ball mill work index(Kaya, 2010)."

Jan 1, 2017

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By P. R. Brito-Parada, A. Norori-McCormac

Positron emission particle tracking (PEPT) has become an important tool for flotation research, as it is able to resolve directly the behaviour of particles in laboratory scale flotation vessels. The first applications of PEPT to flotation showed only the motion of an individual particle in the pulp and the froth, but nonetheless allowed interpretations of behaviour not previously possible. Since then, PEPT measurement and data analysis techniques have improved significantly and now ensure a high level of confidence in the particle behaviour obtained. In particular, statistical analysis of long-duration experiments allows time-averaged data to be collated, ensuring spatial accuracy and allowing rigorous comparison of different conditions. It will be shown that these PEPT techniques can be used to compare directly the effect of operating conditions and particle properties in a laboratory flotation system. Particle tracks will be illustrated, as well as analyses of particle speeds, average flow streamlines and occupancy that show marked differences in behaviour near the interface and impeller.

Jan 1, 2015

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By T. W. Wong, M. A. Whitney, A. Hadadzadeh

Uniaxial compression tests were performed on cylindrical specimens, 10mm in diameter and 15mm in height, machined from an extruded AZ31B magnesium billet. The tests were conducted under isothermal conditions to a true strain of 0.5. The study compares macroscopic flow anisotropy between the extruded (ED) and transverse (TD) directions in the temperature range of 300°C to 500°C, and strain rate range of 0.001s-1 to 1s-1. Compression of ED specimens at low strain rate (0.001s-1) exhibited axisymmetric flow, and no significant differences were observed between geometries of specimens deformed above 350°C under the same strain rate. Deformation of TD specimens at low temperature and/or low strain rate resulted in elliptical cross-sections, with the anisotropy of flow being less significant at higher temperatures. Other studies performed using rolled plates have proposed that pyramidal slip and cross-slip at higher temperature eliminate the effects of initial texture, while the dominance of prismatic slip at lower temperatures will result in anisotropic flow. It is believed that the initial fiber texture common among extruded HCP-structured materials plays a role in the anisotropic deformation behaviour observed in the extruded specimens

Jan 1, 2015

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017

By W. Hawker, A. M. Ivana

"Pressure oxidation is used to liberate gold from refractory sulphide ore and concentrates with over fifteen autoclaves in operation. Despite the importance of pressure oxidation, the autoclave chemistry and chemical thermodynamics are not well established. For example, there is no consensus on aqueous iron speciation or stability of jarosite phases. Additionally, there remains questions about basic ferric sulphate formation and stability. In addition to a review of the current state of knowledge, a methodology to study the ferric precipitation reaction and relate the results to chemical thermodynamic predictions is presented which will be used to accurately define the phase boundaries of the iron precipitates in the future (hematite, jarosite and basic ferric sulphate).INTRODUCTION With declining availability of orebodies that respond to simple leaching conditions, pressure oxidation has become a prevalent technology to liberate gold locked in sulphide mineral matrices. Gold pressure oxidation was established 32 years ago, with McLaughlin being the first facility in 1985 (Thomas & Pearson, 2016). Pressure oxidation is carried out at elevated temperatures ranging from 180 to 240°C as shown in the summary of operations in Table 1 (Ruonala et al., 2016; Fleming, 2010).A considerable amount of research has been done to study iron solubility and precipitation under autoclave conditions (Tozawa & Sasaki, 1986; Umetsu et al., 1977; Sasaki et al., 1993; Fleuriault, 2016; Cheng & Demopoulos, 2004; Papangelakis et al., 1994; Yue et al., 2003). These reports provide a description of the process chemistry and iron behaviour in the autoclave. However, there remain questions about the type and stability of aqueous species and solid phases. This detailed information is required to build a robust chemical thermodynamic model of the system, allowing for equilibrium and kinetic reaction limitations to be discerned."

Jan 1, 2017

By K. E. Waters, N. Brodusch, R. Gauvin, A. Jordens, Teng. C., H. Demers

Rare earth elements (REEs) become increasingly significant for renewable energy devices and high-technology electronic products because of their large-scale popularity and applications. In this project, a field-emission scanning electron microscope was used to characterize the composition and distribution of REEs-bearing minerals. X-ray elemental maps were acquired with a large area x-ray detector (60 and 80 mm2 collecting area) and annular detector (60 mm2 collecting area), which allow fast x-ray acquisition at high count rate. These elemental maps were transformed into phase maps, which are used to identify the composition of the mineral phases and the REEs distribution over a large area. The phase maps are an easy way to distinguish the phases with and without REEs and compare the efficiency of different REEs extraction processes. Different methods (manual and automatic) for producing phase map were studied by comparing the distribution of REEs obtained from the same area.

Jan 1, 2015

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

By H. Utsunomiya, J. Su, K. S. Tamimi, S. Yue, M. Sanjari, L. Kestens, A. S. Kabir, R. Petrov

The recrystallization and texture evolution of AZ31 sheets obtained through two stages was investigated at different stages of post-rolling annealing. The specimens were rolled at the temperature of 100? and at a fast speed of 1000m/min and low speed of 15m/min with a reduction of 30% in one pass. The results show thatAZ31B sheets rolled at 15 m/min and 100 °C has fractured for reductions of more than 30% per pass. However, by increasing the rolling speed to 1000 m/min the rollability was improved significantly and the material can be rolled to reductions of more than 70% per pass. The high speed and heavily deformed materials are fully recrystallized even at 100 °C.

Jan 1, 2015

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By C. Tissot, R. Palmer

"Due to the low concentrations of gold, direct measurement of gold concentration in ore on belt has not been seriously considered to now. Pre-concentration or sorting strategies have largely consisted of particle sorting based on secondary characteristics such as colour, which can be successful in select cases. CSIRO has produced sample measurement results using gamma activation analysis of ~300 gm samples with accuracies of around 30 ppb at best. With this encouragement, a feasibility study into gold ore measurement on belt for the purpose of sorting pods of gold ore has been undertaken. The study described here included, prototype design options with existing industrial Linacs, extensive Monte Carlo modelling of measurement sensitivity and shielding, further sample measurement, a study of the interaction of target measurement accuracy and sorting efficiency, and a rough estimation of potential economic benefit. The projected model sensitivity of around 0.1-0.15 ppm (1 standard deviation) in 10 seconds for 1 ppm average feed result in good bulk sorting performance and intriguing economic potential.INTRODUCTION Pre-concentration or sorting strategies for gold ores have largely consisted of particle sorting based on secondary characteristics such as colour or density, which can be successful in select cases (Klein, 2010). No method is available to measure gold content for sorting in particles or even in bulk on belt, principally due to the low concentrations of gold present. In fact, in many cases it is difficult to do rapid bulk grade measurements of base metal ores with concentrations many orders of magnitude higher. By a fortunate quirk of nature gold is particularly amenable to gamma activation analysis (GAA). CSIRO has performed extensive work in GAA of samples of crushed ore (Tickner, 2017). This has resulted in the Photon AssayTM technique that is currently being commercialised through the CSIRO spinoff company Chrysos. The technique relies on the recent availability of industrial high intensity X-ray sources such as Linacs which are currently being used in industry for security, medical and sterilisation applications. This development has led to CRC ORE funding a feasibility study to determine whether on-belt measurement of gold concentration is possible at a rate and accuracy sufficient to be useful for bulk sorting, where pods of ore are diverted rather than individual rocks. The study in the first instance is based on Monte Carlo modelling that has successfully predicted the performance of the sample based gold measurements. As well as the measurement feasibility consideration was also given to the likely heterogeneity of gold ores and hence the degree to which useful separation could be achieved. This is then tied to a back of the envelope evaluation of the order of magnitude economics of bulk sorting in an example deposit."

Jan 1, 2017

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By Haibin Ma, Jie Song, Qingyou Han, Xiaoming Wang, Wei Vian

In the grain refinement of aluminum, Al3Ti and TiB2 particles are introduced to reduce the casting grain size down to 200 micrometer level, which makes cold working possible. The particles are brought in by the addition of Al-Ti-B type master alloys. It is generally believed that TiB2 particles are stable and nucleate a-Al grains in solidification in the presence of extra titanium than the stoichiometry of TiB2 from the dissolution of Al3Ti particle in the master alloys. Titanium in solution either form Al3Ti layers on the surface of TiB2 particles or as solute to promote the nucleation and to restrict the growth of a-Al grains. However, a consensus on a grain refinement mechanism is still to be reached due to the lack of direct observation. This paper presents finding on the TiB2/Al3Ti interfaces in an aluminum matrix. It demonstrates a strong epitaxial growth of Al3Ti on the surface of TiB2 particles, a sign of the formation of an Al3Ti layer on the surface of TiB2 particles in grain refinement practice. The Al3Ti layer has a crystal coherency with a-Al and hence offers a substrate for heterogeneous nucleation of a-Al grains.

Jan 1, 2015

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015