Search Documents

By J. W. Reynolds

Use of crushed waste rock recovered by sink-float separation from normal ore production for backfill is an established procedure at Commco's Sulhvan mme, Kimberley, British Columbia. Need for a safe method of placement in voids which were difficult to reach by gravity methods led to a co-operative venture with Radmark Engineering Ltd. in the development of a workable pneumatic transportation system for rock material. This paper reviews work done to date in a current program, and includes comments on the nature of the fill so placed, options for cementing such fill, implications for other aspects of mining and references to other applications of the system by other organizations who exchanged experiences with the Sullivan mine staff during the five-year period reviewed.

Jan 1, 1972

?Four-wheel, skid-steer, rover developed for CSA ?U-chassis for payload accommodation ?Passive geometric suspension ?Max speed 13km/hr ?Remote workstation ?275kg payload capacity ?On-board processor, IMU, motor encoders ?5.2kW-h battery capacity

May 1, 2013

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By L. H. Bergmann

THE blasting practices described are fairly representative of those employed in the coal mines of Eastern Canada. As such, they may be of interest to Western Canadian coal mine operators. The treatment of the subject is general, no attempt being made to discuss blasting operations at any particular coal mine in detail. All the mines dealt with are mining bituminous coal and are classified under the Coal Mines Regulation Act of the Province of Nova Scotia as 'closed light' mines. As such, they are required to use only 'permitted' explosives and to apply them in a 'permitted' manner, except where authority is given by the Mines Department to do otherwise.

Jan 1, 1945

By Samuel Frimpong

Green house gases have become a major concern within the international community over the last two decades due to their potential link to global warming. Carbon dioxide (CO2) is the principal greenhouse gas. In the Kyoto Agreement, Canada has committed to reduce emissions by 6 % below 1990 levels by 2012. This presents a serious economic challenge to Canada and Alberta. Over the next decade, oil sands production expansion, population and industry growth and energy demand will increase CO2 emissions. Current and future CO2 emissions and their economic implications in Alberta will be critical in formulating a comprehensive and balanced policy for dealing with concerns in this area. Disposal of carbon dioxide (CO2) in land aquifers is a potentially viable option for Alberta in dealing with long-term CO2 emissions. Studies have confirmed the existence of appropriate aquifers in the Alberta Basin for CO2 storage over a long geological period. Carbon dioxide is an ideal candidate for aquifer disposal because of its high density and solubility in water at relatively high pressures. In this study, the authors develop a computer simulation model of a scaled aquifer disposal system. The scaled model consists of an injector well, aquifer environment with dominant Ca++ and Mg++ cations. Liquefied CO2 is injected at an appropriate pressure and concentration through an injector well model. The injected CO2 migrates from the point of contact between the injector well and the aquifer domain to the main regime of the latter. The rate of migration is a function of porosity, permeability, cations, aquifer fluid flow regime and CO2 injected pressure. These models are validated using flue gas data from the 546 MW Wabamum Power Plant in Alberta. The total energy requirements for aquifer CO2 disposal system are distributed between a minimum of 105 MW and a maximum of 172 MW, with a mean of 132 MW and a coefficient of variation of 10%. The results show that there is significant variability in all the energy requirements for the CO2 disposal system. The total energy requirements for the disposal system as a fraction of the total power generated by the Wabamum plant of 546 MW could be between 0.19 and 0.32. This is a very significant energy requirement and thorough analysis must be carried out to reduce this variability and energy requirements.

May 1, 2001

By S. Gößling-Reisemann

Most copper ores contain valuable co-products such as molybdenum, gold, silver, nickel, etc. Sulphuric acid and steam are valuable by-products, which are generated dur¬ing copper production. The environmental impacts from mining and refining therefore need to be shared between these by-products and co-products, an issue in Life Cycle As¬sessment (LCA) referred to as allocation. There are different, recognised methodologies for doing so: burdens can be allocated based on the market values of these commodities, they can be allocated by mass, volume, molar amount, functionality, or other physical, technical or economic factors. All of these methodologies have their respective merits and restrictions, and the choice is usually case specific. Nevertheless, the choice between alternative methodologies can have dramatic effects on the LCA results. Recycling in LCA has to be handled in a similar way, as it essentially constitutes a special case of co¬production. The existing standards (ISO 14040 ff.) allow different methods for imple¬menting recycling and allocation into metal LCAs (open loop, closed loop, value cor-rected substitution, etc.), which are still a subject of discussion in the scientific community. However, the methodology used can significantly influence the ecological profile of copper and copper products. We will present an overview of the different methodologies available for including recycling and allocation and give an analysis of how the meth¬odological choice affects the final LCA results. This work will be followed up by quantitative case studies.

Jan 1, 2007

By C. Van Den Heuvel, C. B. Van Buuren

BIOX® has been successfully demonstrated over the past 2 decades for the recovery of gold from refractory sulphide concentrates. To date 12 successful BIOX® plants have been installed in 8 countries spanning 4 continents with the 13th installation currently nearing completion in the Philippines. In 2010 BIOMIN introduced the ASTER™ process for improved water balances in commercial BIOX® applications by supporting tightening environmental legislation on water usage and availability in both arid and tropical regions. Previously, a common challenge for BIOX® plants was the inability to recycle thiocyanate containing water due to the low tolerance of the organisms. ASTER™, a biological thiocyanate and cyanide destruction process, renders a non-toxic solution for re-use in BIOX®. Two commercial ASTER™ plants are in operation with the 3rd ASTER™ plant under construction in the Philippines. A 3rd BIOMIN technology, specifically developed for double refractory ores is available for implementation. The HiTeCC process has shown considerable success on ores where competition from disseminated carbon has rendered ineffective gold recoveries. Through HiTeCC, gold is desorbed from the carbonaceous matter by manipulating the ionic strength and temperature of conventionally treated CIL product. One Australian commercial plant utilises HiTeCC while a 2nd installation is set for commissioning 4th Quarter 2014. BIOMIN’s premier solutions for refractory gold processing are described herein.

Jan 1, 2014

By J. Aydt, W. McCombe, H. McLaughlin, L. Nightingale-Mercer

The McClean Lake mill is located approximately 850 kilometers north of Saskatoon, Saskatchewan, Canada and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and in 2014 completed a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum. This expansion included significant changes to the mill’s secondary leach circuit in support of safely processing high grade ore directly from the Cigar Lake mine. In particular, inter-stage pumps were introduced for slurry transfer between the secondary leach tanks, replacing the original pressure feed forward operation. The design and selection process for these pumps was strongly influenced by the uncertainty related to actual radiation dose exposure when processing undiluted high grade ore (up to 30%U), and consequently the desire to maintain minimal occupancy in the vault enclosure containing the secondary leach tanks. These constraints resulted in the decision to install positive displacement pumps above the leach tanks in a suction-lift configuration. Operating experience with this design has shown that the pump capacity is significantly de-rated due to process solution gas-entrainment and pipe scale build-up, particularly in the front end of the secondary leach circuit where reagent dosage is high. Experience processing high grade ore also provided accurate radiation dose data to demonstrate that the level of occupancy in the leaching vault enclosure could be re-evaluated to accommodate alternate pump configurations. This paper reviews the lessons learned and improvements made to safely increase the capacity and reliability of the leach inter-stage pump system.

Jan 1, 2020

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By H. A. Kee

In the mining industry, as in other business, one of the more satisfactory results of sincere but cheerful effort lies in the proper completion of undertakings and problems, which, to be successful, must continually hold the interest of all concerned in the work. In most undertakings, genuine interest and satisfaction is largely dependent on the proper appraisal of opportunities presented, and the opportunity to associate ourselves with sinking operations at McIntyre central shaft, from the surface to a depth of 4,133 feet, was genuinely appreciated. This opportunity was made possible by the previous persistent and successful leadership of Mr. J. P. Bickell, President, with the assistance of his associates, and of the general manager, Mr. R.J. Ennis, in the development of the McIntyre Porcupine mine, and I beg to state that any success in this sinking operation was very largely due to the congenial co-operation and splendid workmanship of Captain Martin C. Horne, his shift bosses, leaders, and all those who worked with us . Our slogan throughout was " Safety First for Pleasant and Efficient Workmanship," and this general policy made it possible to sink and timber 2.,123 feet during the first year without a serious accident.

Jan 1, 1928

By P. E. Walker, M. E. Reed, R. C. Sims, B. Snowdon, D. E. Fallas

An advanced Flash Furnace feed system is the key to improving furnace performance. Clyde-WorleyParsons has developed a revolutionary pulseless pneumatic injection feed system technology, capable of delivering a range of benefits to operators of Flash Furnaces. The solution was created by combining the pneumatic conveying and injection knowledge, expertise and technology of Clyde Materials Handling with WorleyParsons' flash furnace process and operating experience. Optimal furnace burner performance requires the feed material to be presented to the burner as a stable, pulseless and accurately controlled flow, distributed evenly around the burner tip circumference. These simple requirements appear obvious, but are extremely difficult to satisfy in industrial environments and are not achieved by conventional feed systems. Our analysis of existing operating furnaces has identified the link between pulses in concentrate feed rate caused by conventional drag chain conveyors and rapid fluctuations measured in the furnace pressure. These fluctuations occur at a timescale close to the reaction shaft residence time and lead to unwanted instability in the primary furnace reaction zone - the flame. Through the use of the solution created by Clyde-WorleyParsons, it is predicted that the much more accurate control of feed rates achieved can lead to substantial improvements in furnace output, increased oxygen efficiency and better control of the composition of furnace liquids, such as matte, blister or slag. All these improvements lead to significant increases in smelter output and efficiency, and deliver high economic value compared to the cost of the feed system. Clyde-WorleyParsons' solutions can be deployed on greenfield sites or retrofitted, and therefore, have the capability to improve feed control at both new and existing smelters. This paper will discuss the field test work undertaken to date, the impact of findings and the ongoing analysis of linkages between instabilities in the various components of conventional feed systems and furnace pressure stability.

Jan 1, 2007

By M. Fall

The progressive depletion of ore available at shallow depths in several underground mines around the world means that underground mining operations would increasingly be carried out at greater depths and therefore at higher temperatures. However, our understanding of the effect of hot temperatures on the response (mechanical, economical, environmental) of cemented paste backfill (CPB) is still limited. Hence, an extensive laboratory investigation was conducted to study the performance of young and aged CPB, in response to deep mine temperatures. Several CPB samples with different compositions, cured at different temperatures (20 to 50°C) and different times (7 to 160 days) were tested regarding their mechanical properties, economical performance (binder consumption) and microstructural properties. The results show that hot temperatures significantly affect the performance properties of CPB at young and advanced ages. An increase in the curing temperature leads to a considerable improvement of the rate of gain of CPB strength and also to a significant increase of the strength of CPBs studied. CBP samples cured at hot temperatures show lower binder consumption and finer pore structure. Results of this study could serve as background information for the development of optimal mine backfill design procedures.

May 1, 2007

By René Dufour

Jusqu?à son acquisition par MM René Dufour et Alain Robin en 1994, les claims miniers et les droits de surface de la propriété étaient détenus depuis 1953 par la société Québec Columbium, une filiale de la socité américaine Kennecott Copper qui y a réalisé d?importants travaux miniers. En 1995 la compagnie NIOCAN inc. fut incorporée; ses actions furent inscrites à la bourse de Montréal en 1997, et à la bourse de Toronto en décembre 1999. Jusqu?à maintenant, NIOCAN a investi plus de 7 millions de dollars dans le développement de sa propriété minière de niobium située à quelques 40 kilomètres au nord-ouest de Montréal. Le haut rendement économique des deux gisements principaux que compte exploiter la compagnie, le S-60 et le HWM-2, a été établie par des études de faisabilité effectuées par le consortium Met-Chem/SNC-Lavalin. La mission que s?est donnée NIOCAN inc. consiste à mettre en production ses deux gisements et à devenir ainsi productrice de ferroniobium dans les plus brefs délais. Figure 2 Le projet est présentement à un stade avancé d?obtention du certificat d?autorisation du ministère de l?Environnement. À plus long terme, la compagnie compte aussi exploiter les sous-produits de ses gisements (apatite, forsterite, magnétite, calcaire et terres rares).

May 1, 2003

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By J. Fujioka, Y. F. Gu, C. Cui, D. Ping, A. Sato, H. Harada

"A new kind of cast & wrought (C&W) Ni-Co base superalloys named as ""TMW alloys"" are developed recently for compressor or turbine disks of gas turbine engines in High Temperature Materials 21 Project at National Institute for Materials Science (NIMS) in Japan. These Ni-Co base superalloys combine the characters of two kinds of y- y' two-phase alloys (Ni-base and Co-18at%Ti alloys) and have higher tensile strength and creep resistance than C&W UNDIMET 720Li superalloy."

Jan 1, 2006

By James L. Parks, David M. Kjos

"Significant increases in mill liner life and plant availability can be achieved by following guidelines that have evolved from over twenty years of practical experience with autogenous grinding (A0) and semi-autogenous grinding (SA0) mills. A0 and SA0 mill liner functions, performance criteria, designs, wear-resistant materials and maintenance procedures are reviewed. Operating practices that can lead to accelerated wear and breakage are discussed.IntroductionEfforts to improve the performance of liners for autogenous grinding (AG) and semi-autogenous grinding (SAG) mills began as soon as the modern, large-diameter versions of these comminution machines were first intalled in commercial plants twenty years ago . While concentrators with conventional circuits were typically running at 95010 or better mill availability, many of the new autogenous and semi-autogenous circuits were struggling to achieve 80% availability. Liner maintenance, which involves not only material and labour costs but also loss of production, was quickly identified as one of the major reasons for downtime.Today, liner designs and materials have evolved to the point where virtually maintenance-free liner life of two to three years is possible in autogenous mills and one year in the more severe operating conditions encountered in semi-autogenous mills. Of concern, however, is that hard-won lessons from the past sometimes seem to be forgotten or ignored during the design of new mills and the operation of existing mills. As liner suppliers, we are often confronted with performance problems that could have been avoided by applying well-publicized guidelines for liner design and materials selection.This paper provides an overview of AG and SAG mill liner functions, criteria for evaluating performance, designs, wear-resistant materials and maintenance procedures. Also, operating conditions that can lead to accelerated wear and liner breakage are discussed in detail."

Jan 1, 1990

By A S. Leitch

This paper is based on the accident prevention pro-gram carried out in the coal mines of Alberta. It defines the role of the Alberta Mines Branch and of The Work-men's Compensation Board, and relates how a safety pro-gram was initiated. The formation of the Alberta Class 1 Mining Safety Council is also described. The responsibilities of both management and the individual worker are then outlined, and the main features of a successful accident prevention program are delineated. T HE purpose of this paper is not to repeat generalities and platitudes about industrial safety, but rather to relate the experience of Alberta coal mines during the past number of years in their efforts to keep accidents to a minimum. It has been learned from experience that many basic principles are as sound today as they were 20 years ago. How-ever the complexities of modern mining methods and the modern man or miner have created problems that did not exist then.

Jan 1, 1964

By R. Carrier

"There has been a continuous evolution with the use of pre-cast concrete elements in the construction of aluminum smelters. In 1990, Phase I of Alouette was built using cast-in-place concrete exclusively. Whereas, other AP 30 technology plants such as Hillside 2 in the mid-1990s used pre-cast concrete beams with cast-in-place floors. Mozal 2, in 2002, used pre-cast concrete beams with pre-cast partial-slab operating floors. Alouette Phase II went further. Not only were the potroom building beams and floors pre-cast, but the entire pot support system, insulating walls and basement jersey walls were pre-cast. Once the techniques for bending and welding the reinforcement bars and the design for attaching electrical insulating plates to the concrete was perfected, the challenge for the project remained only in the logistics of transporting the pieces to site and simple erection. The overall impact on the project was dramatic. Using prefabricated concrete not only allowed advancement of the schedule, but totally eliminated formwork, re-bar installation, and form removal activities along with the handling of all the materials involved with these activities. With the elimination of these labour and material-intensive portions of the job, exposure to work injuries was dramatically reduced. The most prevalent activity for lost time accidents is during the rough work associated with concrete formwork, placing concrete and form removal. Another area where prefabricated elements were successfully used on Alouette Phase II was for the insulating walls enclosing the pot area, known as the ""claustra walls"". Usually these walls are constructed in-situ using mortar and breeze block. Success was also achieved with prefabrication of the perimetric walls that are installed at the lower floor of the potroom. A big advantage of using prefabricated concrete in the electrolysis area is in assuring electrical isolation for the operating floors. Poured concrete requires a meticulous clean-up effort before commissioning to establish the electrically ""floating"" characteristics of the operating floors. Poured concrete results in ""wash"", stray wood,"

Jan 1, 2006

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013