Search Documents

By K. A. Lapakko, D. A. Antonson

Fourteen samples of pyrite-bearing Archean greenstone rock (d < 6.35 mm, 0.04% < St < 1.22%) were characterized (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing. The only sulfide and carbonate minerals identified were pyrite and siderite, respectively. Quartz, chlorite and sericite typically comprised 90 to 98 percent of the mineral content. For the first 60 weeks, seven samples with sulfur contents less than or equal to 0.16% produced drainage pH values exceeding 6.0. Over this period, six of the seven samples with sulfur contents greater than or equal to 0.20% produced drainage pH below 6.0, with minimum values ranging from 3.2 to 4.7. The seventh sample (0.72% S) had a siderite content of 18%. Small amounts of magnesium and, to a lesser degree, calcium carbonates present in the siderite apparently dissolved to neutralize acid and maintain drainage pH above 6.0. Sulfate release rates generally increased as sulfur content increased, and the rates of pyrite oxidation estimated for individual samples were roughly half to five times that reported in the literature for the abiotic oxidation of pyrite by oxygen. Observed neutralization potentials ranged from 0.2 to 2.0 g CaCO3/g rock.

Jan 1, 2002

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By S. McCalpine, W. Muir, P. J. Downey

"Golden Bear Operating Company Ltd. (GBOC) was a joint venture between Chevron Minerals Ltd. and North American Metals Corp. that was formed for the development of the Golden Bear Project. The mine is located at Muddy Lake, Western British Columbia, approximately 80 km northwest of Telegraph Creek and 135 km west of Dease Lake (see Figure 1). Road access to the mine was developed by Golden Bear and consists of a radio controlled 155 km gravel road originating at highway 114.A feasibility study was completed in 1987 and project approval was finalized in 1988 with Golden Bear issuing a ""Request For Proposal"" for detailed engineering in May 1988. Golden Bear also commenced negotiating with vendors at this time for the supply of the two principal process equipment packages: the dry grinding and classification system and the whole ore roaster package.Process plant engineering and plant construction was completed in October 1989 with plant startup commencing in November 1989. Two months into the commissioning phase it became apparent that the plant, as designed, would not achieve the anticipated production targets.Kilborn Engineering Pacific were subsequently contracted by GBOC to review and modify the plant design, assist the operating personnel with plant commissioning and startup and provide operator training.This Paper describes some of the problems encountered during the startup and the plant modifications incorporated to achieve design parameters."

Jan 1, 1992

The following paper deals with a method for the&quot; Proximate Analysis&quot; of Chloridized Ores, which are free from arsenic, antimony and lime. When these are present the analysis is rendered far more complicated, and many of the methods which I am about to describe could not be applied. Sufficient scope is therefore offered for discussing the analysis, when these metals are present, in a separate paper, which I hope to contribute at a future date.I am fully aware that this method is far from being perfect. No doubt many, modifications and improvements will suggest themselves to my readers, and I trust that this paper will be the means of giving a certain impetus to the study of Proximate Analysis which at the present time is practically dormant. For the benefit of my readers who are not initiated into the details of ordinary estimations, I have briefly described well known methods, which, however, will be found fully described in most text-books of analysis. Assuming that the ore contains. sulphates and chlorides of soda and magnesia, sulphates, sulphides, chlorides and oxides of copper, lead, iron, zinc, manganese and silver chloride, the analysis would be conducted as follows. The first compounds to estimate are the chlorides and sulphates of soda and magnesia.

Jan 1, 1901

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By L. K. Weaver

The Bureau of Mines has started an engineering study of oil recovery by miscible-phase displacement. As a preliminary part of the investigation a literature and patent study was made to prevent duplication of work already done, to become acquainted with those actively engaged in research of this type, and to learn where the recovery method has been attempted. This bibliography gives results of this study. The bibliography includes 254 references to U.S. and foreign patents and published literature relating to miscible-phase displacement processes of oil recovery. It is divided into the following sections: (1) U.S. patents, (2) foreign patents, (3) literature references, (4) author index, and (5) publication and source reference. The patents and literature references are listed alphabetically by author by intervals of years. References to February 1963 are included.

Jan 1, 1963

By M. K. G. Whateley, W. Hatton

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 20pp., 31 refs. Estimates of coal tonnage on UK open cast mining sites often vary from the recoverable tonnage. This is because the estimates depend on the geological variability of the coal measures. Geological parameters, such as thickness, quality and disturbance of the seam, have a direct control upon this variance. Risk analysis techniques have been applied using commercially available software to combine each parameter's variability into a cumulative variance, resulting in a tonnage distribution. Sensitivity modelling has also been used to identify the geological parameters which have the largest influence on the variance of the simulated tonnage distribution. An understanding of the relationship between the tonnage and geological variability has helped to focus exploration more efficiently. A cost to risk relationship can now be monitored, helping management to avoid negative consequences on site

Aug 1, 1995

REFERENCES AND FOOTNOTES 1. U.S. Department of the Interior, Office of Surface Mining. Surface Coal Mining Reclamation: 10 Years of Progress: 1977-1987. Washington, D.C. August 3, 1987.48 pp. (For sale by the Superintendent of Documents, U. S. Government Printing Office, Washington D.C. 20402.) 2. The Rural Abandoned Mine Program (RAMP), authorized by Section 406 of SMCRA, provides for the control and prevention o f erosion and sediment damages from unreclaimed abandoned mine lands. 3. The Small Operator Assistance Program (SOAP), authorized by Section 401(b)(1) and 507(c) of SMCRA authorizes up to 10 percent of the fees collected for the Abandoned Mine Reclamation Fund to be used for technical assistance to help qualified small mine operators obtain techincal data needed for permit applications. Operators who produce fewer than 300,000 tons of coal per year are eligible for assistance. 4. OSM regulations 30 CFR 816.42 and 817.42 require water from areas distrubed by mining activities be in compliance with all applicable state and federal water-quality laws and effluent limitations for coal mining established by the U.S. Environmental Protection Agency. 5. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 6. Sourse: Abandoned Mine Lands Fee Collection System, Data from OSM-1 form. 7. Source: OSM Field Office Annual Reports. 8. Johnson, W. and G.C. Miller, Abandoned Coal-Mine Lands: nature, extent, and cost of reclamation. U. S. Bureau of Mines, 1979,29 pp. PHOTOGRAPHIC CREDITS Front cover, pp. i, 1, 2 bottom, 7 right, 10 bottom left, l 1 top, l l bottom right, 12 top, 13 bottom, 14 bottom right, 15,16 bottom, 17 top, 17 bottom right, 18 bottom, 19, 20 bottom, 21 top, 22, 23, 24 bottom, 25 bottom, 26 bottom left, 26 bottom right, 27, 28, 29 top, 30 bottom, 32 bottom right, 33 top, 34 top, 35 top left, 35 bottom left, 35 bottom right, 36 top, 37, top right, 37 bottom, 38 bottom, 39, 41, 42 top, 43 bottom, 44 bottom left, 44 bottom right, 45, 46, 47, and 53: Chuck Meyers, OSM. Page 2 top and center: Tony Fuhs. Page 3: John Sharkowicz, OSM. Page 6 left: North American Coal Corp. Pages 6 right, 7 left, l l bottom left, 13 top left, 13 top right, 17 bottom left, 21 bottom, 25 top left, 25 top right, 29 bottom, 30 center, 32 top, 32 bottom left, and 38 top: Bob Welch, OSM. Page 10 top left: Donald Stump, OSM. Pages 10 right, 14 top right, 14 center right, 18 top, and 44 top: Ron Hill, EPA. Page 12 bottom: Texas Utilities Co. Pages 16 top, 20 top, 24 top: Tennessee Valley Authority. Page 26 top right and 26 center left: Richard Dick, U.S. Bureau of Mines. Pages 30 top, 33 bottom left, 33 bottom right, 35 top right, 36 bottom, 37 top left, 40 top, 40 bottom, 42 bottom, 43 top left, and 43 top right: Jim Boyer, OSM. Page 31 top left, and 31 top right: Bruce Wage, Western Energy Co. Page 31 bottom: Rex Wilson, OSM. Page 34 bottom: West Virginia Division of Abandoned Mine Lands. Page 35 center: William Weist, Jr., OSM.

Jan 1, 1992

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By Marco A. Vera

"This paper investigates the froth function in flotation and the associated upgrading process. Flotation literature has revealed that one of the main functions of the froth phase is the cleaning of bubble-particle aggregates by rejection of entrained material. The cleaning and transport processes across the froth phase exert straining forces on these aggregates on their way up to the froth surface. These forces will impact on the recovery of bubble-particle aggregates.The grade at the top of the froth (TOF) is a parameter related to the quality of particles collected by bubbles in the pulp zone (true flotation). It has recently been demonstrated that TOF corresponds to the maximum practically attainable grade described by the recovery-grade (or enrichment ratio) curve. TOF lumps all the processes experienced by the bubble-particle aggregates before reaching the launder concentrate. This paper describes a methodology for quantifying flotation performance by means of the top of the froth sample - a touch of froth.INTRODUCTIONFroth flotation may be the most important mineral processing technique, but its theory is complex and is not completely understood even though many aspects have been studied and reviewed (Teague, 1998; Wills, 1992).Two distinct particulate systems prevail in the flotation process: a pulp phase and a froth phase (Figure 1). The pulp zone had been studied extensively; however, it is only recently that techniques to measure the froth zone performance have been developed (Contini et al., 1988; Falutsu and Dobby, 1992; Feteris et al., 1987; Seaman, 2002; Vera et al., 1999b).Flotation involves a number of mass transfer processes, occurring in the pulp phase and the froth phase. The formation of the froth and its subsequent removal are considered to be two important steps of the process. Phenomena that occur in the froth phase are known to affect flotation performance significantly (Cutting et al., 1981).Because the froth has a high free surface energy (as a result of the extensive interfacial surface between liquid and air), it appears thermodynamically unstable. The foaming is a dynamic balance, as new bubbles are added continuously from the pulp, while others disappear from the top. Under steady-state conditions, the volumes of added and subtracted air are equal (Booth, 1953)."

Jan 1, 2003

Conventional waste management practices produce two waste streams for the construction of separate disposal facilities. The design of tailings impoundments is usually controlled by physical stability. Waste rock materials offer high shear strength characteristics for waste dump construction, however the hydraulic properties promote oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. Co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retention capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimize acid generation and metal leaching. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repository. The results of a laboratory program to characterize the physical and hydraulic properties of Comix tailings and waste rock are presented here. Various ratios of tailings were blended with three distinct waste rock materials. The saturated hydraulic conductivity for the Co-mixed materials was found to vary between 2 x 10-7 m/s and 5 x 10-8 m/s depending on blend ratio, waste rock type and compaction. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the hydraulic behaviour of a Co-Mix waste system. The potential benefits of Co-Mix are shown for a typical mine.

Nov 1, 2002

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author&apos;s aim in this paper to describe the method in use at the North Broken Hill Oompany&apos;s British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

By A. Monomakhoff

If a conductor traversed by an electric current is broken, a conduction forms in the air between the two broken ends of the wire. This conduction manifests itself in an initial phase by an electric spark and, in a second phase, by an arc if the the circuit continues to supply sufficient power. This arc goes out when the distance between the two ends of the conductor becomes sufficiently large. If the break occurs in an explosive atmosphere, the energy contributed by the arc can cause an explosion. To avoid such accidents, electric circuits that may be utilized in hazardous atmospheres can be made "intrinsically safe". The investigation which we conducted is part of a research project on the intrinsic safety of arcs of high intensity but short duration, in the case of resistive circuits. We developed an electronic system which makes it possible to limit the duration of an arc at the level of the break of a conductor traversed by a current with a possible maximum intensity of 80 amperes. This experimental device for monitoring and measuring the parameters of the arc has shown that arcs of high intensity but with a duration limited to a few microseconds do not ignite an explosive methane-air mixture.

Jan 1, 1975

By M Begbie, R J. Norris, D J. MacKenzie

The Otago Schist is crossed by numerous deformation zones that formed in the latter stages of metamorphism and uplift of the metamorphic belt. These deformation zones are long (tens of km) linear features at the regional scale, and are generally narrow (km scale or less). Many of these structural zones separate schist domains with different rock types and structural/metamorphic histories. The Hyde-Macraes Shear Zone is one such deformation zone, and this zone hosts the active Macraes gold mine. The Rise &amp; Shine Shear Zone, 80 km NW of Macraes, is also enriched in gold and has been mined historically. Mineralisation in both these shear zones occurred during the transition from ductile to brittle deformation as the schist belt was uplifted from greenschist facies metamorphic conditions. Recrystallisation of quartz and micas in the early stages was overprinted by cataclasis, with sulfide and gold precipitation throughout. Many of the other late metamorphic deformation zones formed under similar greenschist to sub-greenschist facies conditions, with similar overprinting of recrystallisation textures and folds by more brittle textures such as breccias. Under these conditions, originally regionally pervasive deformation at the highest metamorphic grades was evolving towards more focussed high strain zones at lower temperatures and pressures. Shear zones initially focussed fluid flow along microshears and mineral grain boundaries, resulting in 1 to 100 m scale alteration and replacement in the host schist, with only local development of quartz veins. Fluid flow was not controlled by open fractures, and the rate of fluid movement was probably slow and pervasive. After uplift into the brittle regime, the schist belt underwent tectonic extension. Extension was accompanied by development of swarms of steeply dipping veins, with localised mineralised normal faults. Hydrothermal fluid flow throughout this uplift history was a normal consequence of late stage devolatilisation of the metamorphic belt. Hence, all late metamorphic deformation zones should be considered prospective for gold accumulation.

Jan 1, 2005

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

Effective gas management in coal mines, as well as proper ventilation design, is very important for maintaining the safety of underground coal miners. Advances in numerical modeling techniques have enabled evaluations of the coal mining environment using advanced grid designs and computed gas distributions through detailed mathematical models. These models help engineers to see the unseen areas of the mine through visualization of the data and ultimately help improve worker safety. This paper summarizes the modeling efforts conducted by NIOSH in the U.S. and CSIRO in Australia to address various gas management issues encountered in longwall mines. The modeling studies involved two of the most widely used grid-based techniques, namely computational fluid dynamics (CFD) and numerical reservoir modeling. This paper discusses the application of these techniques for gob inertization and gas control for spontaneous combustion, pre-mining degasification of coalbeds, gob gas venthole design and performance evaluation in longwalls, and gas management during development mining.

Jan 1, 2009

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

By Thornton L. Neathery

Geologic investigation of a mineralized zone in eastern Alabama indicates that large quantities of talc and soapstone are scattered over a wide area close to the surface. Laboratory experiments show that this material may be upgraded to a high-quality talc. A market survey indicates that the talc deposits may be of current and long-range interest. The anthophyllite asbestos which is associated with the talc does not appear to occur in sufficient quantities to be considered as a primary commercial source.

Jan 1, 1967

It has long been recognised that Australia can benefit substantially in an economic sense from its rich resource base. The significant resources of the Gippsland Basin are a good example of the wealth of this nation. As cited in popular debate, Australia must value-add to its natural resources to ensure its long term economic prosperity. The significant oil, gas and coal resources of the Gippsland Basin have provided the Strategic Research Foundation with the basis for two major research and development initiatives ensuring the long term economic development of the Basin and Australia. The gas and coal reserves of the Basin together with the area&apos;s extensive history in electricity generation provide the rationale for establishing Ceramic Fuel Cells Ltd. A consortium comprising Australia&apos;s leading industrialist - BHP, State energy authorities and the Nation&apos;s major research and development organisations, has formed Ceramic Fuel Cells to undertake and manage research, development and commercialisation of solid oxide (ceramic) fuel cells which convert fossil fuels directly to electricity with greater efficiency and less pollution than existing technologies. The oil and gas resources of the Basin together with the valuable experience of the operators in recovering these resources, have provided the impetus to investigate the feasibility of a Marine Engineering Research Centre. The commercially oriented research, education and training objectives of the Centre are well supported by the leading industrialists in related industries.

Jan 1, 1992

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989