Search Documents

By M. Jahazi, P. P. Bhattacharjee, K. Chadha

The present work investigated the effect of strain reversal during high pressure torsion on the evolution of microstructure, texture and hardness properties of two different materials with different dynamic recovery behavior, namely, high purity (99%) Aluminum (2N-Al) and Aluminum-Magnesium (Al-2.5%Mg) alloy. In the two aluminum alloys subjected to different routes, the evolution of the ultrafine structure followed same trend. At lower strain level, sub grains with prominent LAGBs network were observed and at higher strains, ultrafine equiaxed grains separated by HAGBs were observed throughout the disk. The texture evolution in monotonically and strain reversal processed 2N-Al and Al-2.5%Mg showed presence of typical torsion texture components at different strain levels. The strength of the components was observed to follow different trends depending on the processing routes.

Jan 1, 2015

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By Behrouz Abedian, Livia M. Racz

"We address dynamic interactions between high-energy, reactive surfaces of polymer-matrix composites and solid surfaces. A common characteristic of these interfaces is that bonding occurs readily upon contact. In many industrial and biomedical applications, it is desirable to suppress this bonding phenomenon. This interfacial effect is discussed in light of the development of our new method of handling polymer-matrix composites in dental applications. This method involves vibration of the solid-polymer interface at different frequencies. For each material, there is a critical frequency at which the sum of the viscoelastic and inertial energies of the fluid at the surface exceeds the energy available for bonding. When the polymer is vibrated at or beyond this frequency, it does not adhere to solid surfaces. An important aspect of the developed process is that it can be used to characterize surface and interfacial properties of polymers under dynamic conditions, whereas existing techniques are restricted to the study of bulk dynamic properties.IntroductionThe purpose of this paper is to report on the development of a new method for manipulating polymer-matrix composite materials used in dental applications, and the potential of this process for use in materials characterization. The materials under discussion have polymer matrices of a combination of bisphenol A-glycidyl methacrylate (BIS-GMA) and triethylene glycol dimethacrylate (TEGDMA), and contain filler particles of silica and/or zirconia glasses. These materials are called direct aesthetic restorative materials, and are used for filling of cavities, repairing chipped teeth, and for other restorations in which appearance is of importance. They have the appearance of natural tooth material, and are therefore in great demand for use in the anterior portion of the mouth(l,2)."

Jan 1, 1998

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

By R. Peterson, D. C. Popko, J. Y. Hwang, R. McChesney, A. M. Hein, R. C. Greenlund, M. Jeong

MTU is conducting a study to recycle and reuse the aluminum waste generated from various segments of the aluminum smelting industry. This research is supported by the U.S. Department of Energy and industry. A portion of this effort is to determine the operating efficiencies of Eddy Current Separation, comparing separating characteristics of white and black dross. The results of this effort will be presented here.

Jan 1, 2000

By Lu Lin, Yan-ping Bao, Min Wang

In order to forecast the cost of dephosphorization during BOF process, and achieve economical dephosphorization of BOF. The mathematical model of dephosphorization cost for BOF process was established. The model calculations show that, when the silicon content and phosphorus content are increased in hot metal, and the final phosphorus content of BOF is decreased, the dephosphorization cost will be increased. The silicon content of hot metal is increased of 0.1% in the plant, the dephosphorization cost is added by 9 RMB/ton steel. The De-P cost of mode A is much higher than the other two modes for three typical production modes of single slag melting process, when the phosphorus content of hot metal is higher than 0.14%, an increase in the phosphorus content by 0.01%, the De-P cost of mode A is added by about 7 RMB/ton steel. Meanwhile, when the phosphorus content of hot metal is lower than 0.165%, the De-P cost of mode C is higher than mode B’s. For BOF single slag melting process, the dephosphorization cost calculated by model is between ± 2%, proving that the model is reliable for the prediction of dephosphorization cost.

Jan 1, 2015

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By Claude Lorenson

"The Spyrometer™ imaging pyrometer brings new dimension of imaging capabilities to temperature measurement technology by combining a high temperature video camera with scanning optical pyrometry. This gives the operators the ability to observe process conditions while measuring the temperature of virtually any object or region in the field of view. Since the lens tube of the camera can be air or water cooled, it is possible to see inside furnaces giving a very good view of many different types of metallurgical processes. Specific benefits in process knowledge and maintenance tasks for furnaces in different types of metal industries are discussed.1-Principles of Imaging PyrometryLens tube, camera and processorImaging pyrometry is the combination of video imaging and computer-driven pyrometry that measures the temperature of certain zones (selected by the operator) within the image viewed on the monitor screen. To obtain a detailed image of the metallurgical process under observance, it is necessary to place the optical objective of the camera close to the process. The Spyrometer™ (which is Quadtek's tradename for its imaging pyrometer) objective is housed in a lens tube that is cooled and permits insertion inside the vessel of interest. The length of the lens tube is chosen on the basis of making sure that the tip of the tube is just beyond the refractories lining the inside of the furnace. In most pyrometallurgical processes, we have found that the most reliable system set-up uses a water cooled shroud to cool the lens tube optics. A sapphire window provides maximum protection from the environment. Even in the case of the water cooled version, there is an air purge for the lens that keeps the objective clean and protects against hot metal splashes."

Jan 1, 1997

By Laihua Wang, Peter Hayes, Hae-Geon Lee

"This paper introduces a new process for the efficient removal of dissolved gases and inclusions from liquid metals. This process involves the creation and dispersion of fine bubbles in molten metals by introducing inert or reactive gas into a region of turbulent flow. The highly turbulent metal flow splits the gas into fine bubbles and results in good mixing between the gas and molten metal phases. These conditions are ideal for contacting inclusions in the metal with the bubbles and subsequent flotation of the inclusions to the metal-slag interface where the inclusions are then absorbed by the covering slag layer. Dissolved gases, such as [H], [0], [N] in the metals are also transferred to the gas bubbles and removed from solution.The process concept has been previously demonstrated using a full-scale air/water model to simulate the ladle-to-tundish system of continuous casting of steel. The present cold modelling work has further demonstrated the ability of the process to remove gas solutes. The results indicate that the efficiency of new process is several hundred times greater than that of conventional high speed rotating injectors which are currently applied in the treatment of liquid light metals.IntroductionDuring metal smelting, refining and alloying processes, unwanted gas and second phase liquid or solid impurities are incorporated into liquid metals. In the case of steelmaking, the gas-forming impurities include [0], [H] and [N], and the solid impurities as a result of deoxidation include Ah03, Si02 inclusions. Common impurities in liquid aluminium are dissolved hydrogen and solid Ah03. To avoid subsequent problems during processing and to improve the physical properties of the metal products it is necessary to significantly reduce the level of impurities."

Jan 1, 1996

By Andre Krzysik

"Fluidized bed technology has been used in the industry for almost 100 years. To fully understand the process hundreds if not thousands of researchers were and are involved in finding the way to predict the behavior of the solids when subjected to the flow of media through them and the conditions of the solids in the fluidized state. The difficulties in predicting the behavior of solids in the fluidized state stem from the complexity and abnormality of the parameters related to the solid particles. Theoretical calculations can in some degree account for some of them. Particle size distribution, their shape, density, moisture content and physical and chemical reaction that may exist in the fluidized bed reactor play an extremely important role and influence the behavior of the fluidized bed. This paper focuses on the practical examples of the fluid bed equipment and the use of different conditions to process various products.IntroductionEach process application has its own unique requirements and the designers of the equipment must take into consideration specific process requirements, specific properties of the material to be processed (both physical and chemical), and physical and chemical reactions/changes that are taking place in the reactor (heat and mass exchange, chemical reactions, isomorphic change etc.). Each individual piece of equipment must also satisfy specific requirements/ preferences of the client that will operate and maintain the equipment. Those often represent greater challenges than the process on its own, and are equally important to the satisfactory operation of the plant. That includes aspects like location of the equipment, environmental effects, and expected life of the equipment, process control, access, maintenance, and many others.Over the period of time a great deal of research, both theoretical and practical have been carried out and the results of that work are available for equipment designers. For the simple applications that information is usually sufficient and the selection of a suitable solution is relatively simple. In many instances, the available information is not sufficient, and often specialized test work needs to be conducted to obtain additional data. In many cases a pilot installation is built in which the required process is tested. Only then the commercial equipment is designed. The following deal with specific installations that were designed to satisfy specific requirements. In some instances, additional problems were discovered during the commissioning of the equipment that required on site modification. The continuous monitoring of the equipment that was supplied to the various clients allowed us to further develop and improve our designs."

Jan 1, 2014

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modem technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example of a European approach to these matters the paper presents Outokumpu' s response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Takamitsu Nakasuga, Haiping Sun, Kyushu University, Katsumi Mori

"The kinetic behavior of reduction of chromite ore by liquid iron containing carbon and silicon has been investigated under various experimental conditions to clarify the reduction mechanism. It was found that the reduction rate of chromium ore by liquid Fe-C alloy was very slow. In addition, when carbon and silicon coexisted in the iron melt, silicon was found to preferentially oxidized to form silica, which favored for the fonnation of liquid slag and the rate of reduction was considerably accelerated. The similar effect was obtained by the addition of some fluxes, such as SiO2, Na2B407, CaO-SiO2, which also promoted the formation of a liquid slag and thus the reduction rate in the early stage also increased.IntroductionThe reduction of Cr2O3 is a basic reaction for production of ferro-chromium from chromite ore and for chromium recovery from the slag fonned during the decarburization period of a stainless steel-making process. The reduction of chromite ore consumes much energy and its reaction rate is not so high. Thus, in order to increase the reduction efficiency, it is strongly desired to clarify its reduction mechanism from the practical and the theoretical points of view."

Jan 1, 2000

By Tapani Järvinen

Non-ferrous metals and metals in general are considered as being non-renewable natural resources. Metals are needed because of their excellent and irreplaceable properties. The consumption of metals, with the exception of carbon steel, is steadily growing by 1-3 % annually, and that of stainless steel as much as 3-6 %. This is a general trend, which is periodically disturbed by cyclical variations. In recent years so-called "New Economy" has become prominent in the public media and the market value of the traditional industry has been well below its real value and importance. Nevertheless, the modem society requires metals today and also in the future, and the companies using the most modern technology in a responsible way and innovative solutions not only in technology, but also in everything they do will survive. This paper describes the role of Europe as a producer of primary base metals and as a supplier of technologies in the base metals industry. It concentrates on the development and commercialization of technologies and project implementation in the metallurgical industry. As one example ofa European approach to these matters the paper presents Outokumpu's response to the future challenges in the base metals industry. Outokumpu Oyj is one of the leading metals and technology companies in the world of stainless steel, copper, zinc, and sales of technology in metals and minerals businesses. Outokumpu applies its knowledge of metals and processing to generate value for its customers and shareholder. Everything we do, we do in an economically, environmentally and socially responsible way.

Jan 1, 2003

By Peter A. Spencer

Bacterial oxidation technology has the ability to selectively attack sulphide minerals. Selectivity allows oxidation of more reactive minerals and the extraction of valuable metals while leaving the bulk of the sulphide component unreacted. Partial oxidation can be used on arsenopyrite to recover gold and for the leaching of base metals, such as copper and nickel, from pyritic ore and concentrate without generation of large quantities of acidic iron solution, which must be neutralized. Thus, rejection of pyrite during the oxidation process can considerably reduce treatment costs. Acid generation in tailings dams would be minimal, compared with most Thiobacillus cultures, as the optimum growth temperature of Bactechts culture is above ambient.

Jan 1, 1992

By Arthur S. Klein, Hugh R. Lowry

"The Levitation Casting Process is a new continuous casting method that uses an electromagnetic levitation field, instead of a mold, to support and contain a column of solidifying metal. By counteracting gravitational forces and hydrostatic pressure on the metal column, this process eliminates friction and adhesion at the interface between the solidifying metal and the cooled walls of the casting chamber. The process inherently provides high casting speeds, excellent dimensional control and smooth, continuous emergence of solidified product from the top of the casting chamber.Of major importance is that the electromagnetic field produces an intense stirring of the liquid metal both before and during solidification. As a result of this stirring, the cast product has a homogeneous, equiaxed, fine grain structure generally suitable for immediate drawing or other forming operations without the need for hot rolling or other expensive additional processing.This paper reviews the fundamentals of the Levitation Casting Process, results obtained in casting various pure metals and alloys, and the production sized system at Lowell, MA, that uses this process. IntroductionThe Levitation Casting process was specifically developed to meet several requirements including:• Economic at low casting rates• Usable with pure metals and alloys• High, uniform product quality suitable for fine wire drawing or cold rolling into flat strip and tape• Easy cast product shape and size changes• Process inherently stable and easily automatedIn meeting these criteria it was also desired to retain the advantages of General Electric's well known Dip Forming continuous casting process; namely the inherent ""fail-safe"" properties of upward casting, solidifying metal by means other than pressure contact with a cooled mold, and use of a sealed furnace, casting chamber and cooling tower, filled with a protective atmosphere, to prevent oxidation of the molten metal or cast product."

Jan 1, 1988

By Vladyslav P. Yakubovsky, Boris I. Bondarenko, Valentin A. Noskov, Vladyslav M. Sokolov

"Each of Ukrainian producers of ferronickel, stainless steel and synthetic diamonds has the same basic problem with recycling their fine Ni-containing secondary materials. The conditions for generation of them along with the correspondent properties were investigated in details. The new approaches for their recycling have been proposed. They are based on application of some pyrometallurgical processes that are used in Ukraine. The proper equipment is also available. It has been shown that the dust from laterite calcining process of ferronickel production should be efficiently recycled by sintering. The stainless steel dust should be smelted after briquetting as a charge addition to the Ni-containing discarded batteries in the elaborated furnace. The sludge after synthetic diamonds production should be pelletized and processed by liquid cast iron with application of induction magnetodynamic forces in the specific furnace.IntroductionThe object of the investigation is recycling the Ni-containing secondary fines in a form of dust and sludge. There are several generators of the fines in Ukraine. Namely they are Pobuzhye Integrated Ferronickel Mill; Electrometallurgical Works “Dneprospetsstal” with stainless steel plant as well as Poltava Diamond Plant that produces synthetic hard materials. Their businesses are the largest in the Commonwealth of Independent States (CIS). However the status of handling with the fines is not perfect since the applied recycling technologies are low efficient. The landfilling option is often adopted for them. At the same in Ukraine there are some nontraditional pyrometallurgical recycling technologies and equipment that should be tried for application in smelting these secondary materials.Recycling the sludge of synthetic diamonds productionThe sludge of “Poltava diamond plant” from production of synthetic hard materials has a following chemical composition, %: iron oxide – 29.7; chromium oxide – 18.97; nickel – 4.27; manganese oxide – 15.2; sulphate – 3.85; natrium – 14.9. The content of moisture is 70-80%. The moisture quite quickly evaporates while keeping sludge out of doors. Sludge returns into the weak agglomerates. The sizing of the dried sludge particles presents the figures from 400 to 1000 µm. The moisture was extracted by sludge pressing. The content of the basic compounds of the moisture is, g/dm3: chromium oxide – 1.6; nickel – 0.001; manganese oxide – 0.002; lead – 0.005; sulphate – 13.6; natrium – 17.0."

Jan 1, 2008

By Khoo Khyou Pin, Yoshiyuki Funaki, Hirotsugu Takeuchi, Ryoichi Urao, Naotatsu Asahi

"Steel is used to be ion carburized with mixing gas of methane and hydrogen. In carburizing, carbon in the methane decomposes and deposits on the steel by plasma, so methane gas flow may influence on ion carburizing of the steel. An apparatus in which works can transfer preheating, ion-carburizing and diffusion treating zones continuously was made for effective carburizing of steel. The gases were flown into above three zones with three different gas inlets. The hardness and microstructure of the works were investigated after ion carburizing and quenching. The steel is carburized deeper near the carburizing gas flow nozzle of the inlet than far from the nozzle. Hard surface layer fom1ed by quenching of ion-carburized steel.IntroductionGas carburizing is used for a surface hardening treatment which decreases fatigue and wear of the industrial parts used in automobile, machines etc. Ion and vacuum carburizing have been developed recently and applied to some industrial parts of restrictive purposes. The ion carburizing treatment which uses hollow cathode discharge (HCD ion-carburizing) is superior in energy saving, resource saving, environmental cleanness to the other carburizing treatment. Specially, carburizing energy can be saved in HCD ion-carburizing, because highly heated zone can be restricted in the range between work and subsidiary cathode where hollow cathode discharge arises, and the work is carburized in shorter tin1e in HCD ion carburizing method than other carburizing methods. Three treatments of preheating, carburizing methods and carbon potential controlling by hollow cathode discharge tried to be carried out in one continuous transferring series to carburize works more effectively, so the HCD ion-carburizing apparatus with continuous transferring system was made and gears of works were HCD ion-carburized in continuous transferring. The works were rotated themselves to get homogeneous carburizing by continuous transferring in glow of hollow cathode discharge."

Jan 1, 2000

By S. P. Jupp

A 2-D coupled thermo-mechanical model was developed to simulate hot tandem rolling of AA5056 aluminum alloy using the commercial finite element software package, ABAQUS The model was used to predict the temperature, strain rate and strain distribution in the strip at any position in the roll bite and was verified through comparisons with literature results in terms of both temperature and strain predictions at the roll bite exit. A sensitivity analysis indicated that model predictions of temperature and strain at the roll bite exit were sensitive to the friction coefficient and moderately sensitive to the heat transfer coefficient for the conditions studied. Microstructure equations taken from the literature were used to make predictions at various positions in the strip. The temperature, strain rate and strain vary dramatically through the thickness of the strip in the roll bite. The sensitivity of the microstructure predictions to these parameters was assessed and it was found that using average values of temperature and strain rate in the roll bite versus exit values significantly influenced the resulting microstructure predictions.

Jan 1, 2001

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994