Search Documents

By M. Rubinstein, N. C. Koon, B. N. Das, V. G. Harris

"Copper and gold - based alloys having giant magnetoresistance properties were produced by melt spinning from arc melted and cast rods. The ribbon width varied between 1 and 2 mm and the ribbon thicknesses were in the range of 30 to 50 11m. The uniform microstructure of the cast rods indicated the composition homogeneity in the starting material. The ribbons showed composition uniformity across the cross section from EDX analysis. However, the spun ribbon microstructure changed from a 'frozen in' region near the wheel side to a nanosize spherically precipitated phase towards the freely frozen surface. The evolution of the microstructure from the spun ribbon state to the annealed ones was studied by optical microscopy, SEM and TEM. The structural information of the spun and annealed specimens was obtained from X - ray, electron diffraction, electron microscopy and ferromagnetic resonance. Magnetoresistance was measured by the four point probe method.IntroductionRecently. Giant Magnetoresistance. GMR. has been observed in sputtered thin films alloys of Ag. Au and Cu with Co and Fe [1. 2. 3]. The sputtered films are produced by condensation of the alloys from the vapor phase. These Ag. Au and Cu alloys are miscible and homogeneous in the vapor and liquid phase (except Ag alloys which exhibit phase separation even in the liquid phase) but immiscible and heterogeneous in the solid phase. In our work we have produced thin ribbons of the Cu and Au alloys about 30 µm thick from the miscible state in liquid phase by rapid solidification melt spinning. The microstructural development of the ribbons was investigated in the as - spun condition and on annealing. The other properties such as magnetization. GMR and Mossbauer Spectroscopy were also investigated in the various microstructural conditions of the ribbons."

Jan 1, 1994

By Chen Dong, Yuanling Gao, Jilai Xue, Jun Zhu, Luxing Feng

"Porous Ni-Ti alloy has many applications in a wide range of engineering areas. The porous NiTi alloys were prepared from Ti and Ni powders in sintering process under argon atmosphere. The major chemical compositions of the sintered Ni-Ti body were Ni Ti, Nh Ti4O and Nh Ti, respectively, the internal pore structures were characterized by image analysis technique, which were dependent on various processing parameters such as sintering temperature, amount of poreforming agent, forming pressure, etc. The results show that the porous alloy samples had the characteristics of uniform pore and high open porosity; pore-forming agent and sintering temperature are important factors in porous; pressure affected the sintered products' pore, by affecting the combination of alloy powder with pore-forming agent.IntroductionPorous Ni-Ti alloy materials exhibit not only excellent shape-memory and superelasticity, high yield strength and ductility, good corrosion resistance and biocompatibility, but also have low density, low stiffness, and high energy absorption rate due to their porous structures [1]. In recent years, these porous Ni-Ti alloys have found applications in a wide range of engineering areas, such as bone implants [2-4], impedance-matching connectors [5], energy-absorbing structures [6,7], separators [8] and actuators [9], etc.Pore characteristics can play very important role in determining of the performance of porous NiTi alloys. For example, when the alloys are used to repair or replace hard tissue implant material, the pore shape and size not only determine their mechanical properties, but also have great effect on the fluid transmission of human body. The pore characteristics can also influence the stressstrain behavior of the porous Ni-Ti alloy and, thus, strongly affect their mechanical properties, superelasticity, and fracture mechanisms [10].In this study, the Ni-Ti alloys with high porosity were prepared in a powder sintering process under argon gas. The pore characteristics were investigated using SEM, XRD and image analysis techniques, especially in association with the content of pore-forming agent, sintering temperature and compacting pressure."

Jan 1, 2011

By Zhou Jiemin

In order to fully understand the behavior of the rectangular six- electrode electric smelting furnace and improve its design and operation, a three-dimensional mathematical model has been developed which incorporates the electrical and thermal flows into numerical solutions, assuming a steady state regime. The model has been used to simulate the performance of the 16500 kVA nickel matte smelter at Jinchuan in China, and various factors have been investigated. The results of computation are in agreement with the measured data obtained from this furnace and its physical model. Application of this model is described and the calculation on the Jinchuan smelter shows that the operation expenses can be reduced by optimizing the furnace geometry and some operating parameters.

Jan 1, 1991

By Yi Feng Shi

The ISASMELT process is a submerged lance smelting technology operating in smelters in Australia, the USA, Belgium, India, Germany, Malaysia and China. Further plants are under construction in Peru and Zambia. Initially developed at Mount Isa Mines, Australia, the technology is marketed by Xstrata Technology to companies around the world. Yunnan Copper Co. Ltd. (YCC) commissioned the first copper ISASMELT furnace in China in 2002. The plant quickly ramped up to design capacity and the first campaign lasted more than 2 years. Now into the second campaign, the furnace is exceeding the original design capacity and YCC has won numerous awards for its contribution to reducing emissions and energy consumption. YCC and Xstrata put great effort into managing the design, construction and commissioning of the smelter. Xstrata?s technology was combined with YCC?s novel management approach. This effort has been repaid in terms of the outstanding performance of the plant since startup. This paper updates the reader on the first few years? operation of the YCC ISASMELT plant and discusses the way in which the technology was transferred, leading to fast rampup and, as a result, enhanced profitability for the operators.

Jan 1, 2006

By T. Lezhava

A new reactor model with rotating cathodes has been developed where various forms (dendrite, spongy) of metal depositions and their uninterrupted removal are accomplished by the realization of high current densities and low energy consumption. At the same time in contrast with the existing methods a high quality metal powder may be obtained from concentrated electrolytes without any specific organic or inorganic additives, which allows raising the intensity of the process. The reactor can be used for electrowinning of metals with low adhesive capacity (Pb, Ag, Cu, Zn, Ni, Co, etc.) and the powders. The obtained products may be utilized in general metallurgy as well as in powder metallurgy.

Jan 1, 2006

By Dominic T. Jordan, Quinn G. Reynolds, Christopher J. Hockaday, Ian J. Barker

A direct-current (DC) plasma arc furnace is a type of electric furnace used for metallurgical operations. The successful operation of DC furnaces depends to a large extent on gaining a fundamental understanding of the arc phenomenon itself, and ensuring its presence in the furnace at all times. A method for detection of the presence of the arc in a DC circuit is presented, along with discussion of why this may be of value for certain modes of furnace operation such as brush-arc. The theoretical development of the method is presented along with supporting experimental work conducted on large-scale pilot-plant facilities.

Jan 1, 2014

By A. E. Clark

Rare earth compounds are widely known as possessing many extraordinary magnetic properties. In this paper, we focus on the huge magnetically induced displacements (magnetostrictions) which characterize the compounds of terbium with iron (Terfenol). Materials prepared commercially by both free-standing-zone (FSZ) and modified Bridgman (MB) techniques have now become available in large sizes and shapes. Prior to the development of the Terfenol alloys, it was possible to achieve giant magnetostrictions only at cryogenic temperatures. In the cubic Laves phase TbFe2 compound, saturation strains exceed 3000 x 10-6 at room temperature and above. Large magnetization 'jumps' can occur, causing huge spontaneous magnetostrictions with small triggering magnetic fields.

Jan 1, 1992

By Ragnhild E. Aune, Shahid Akhtar, Reza Beheshti

"The potential use of Black Dross (BD) as a raw material for the production of refractories, fluxing agents and glasses is the main motivation of the present study. Heat treatment experiments were carried out in Ar, and under reduced pressure (20 Pa), to evaluate the salt removal efficiency. The chemical composition of the BD after heat treatment was investigated by SEM-EDS and XRD analyses. Based on the present results, it is established that the salt starts to evaporate at ˜1273 K in Ar, and under reduced pressure. The salt removal efficiency in a 20 g sample was found to increase in both cases as a function of time and temperature. Moreover, in Ar the chlorine concentration was lowered to 0.3 wt% after heat treatment at 1523 K for 10 hours. Under reduced pressure, however, 0.2 wt% residual chlorine was obtained after 8 hours at 1473 K.IntroductionIt is believed that aluminum recycling in the near future will become the main route of aluminum production [1]. Black dross (BD) that is produced during this process contains, among other things, high amount of salts like NaCl and KCl [2, 3]. Almost 800,000 tons of BD is annually land filled in United States and this number continues to grow with the increase in aluminum recycling [2]. The BD should be dumped in controlled land field and it is costly procedure [4, 5].The water-soluble compounds in BD react with water or environmental humidity and release chlorides into the water and/or generate toxic gases such as H2, CH4, NH3 and H2 S [6-8]. In the Europe, BD is considered as toxic waste and its disposal as landfill is forbidden [8, 9]. After salt removal, the BD is considered to be non-hazardous and can be buried under ground [10].On the other hand, BD do also contains many relatively valuable compounds that may be changed in to useful materials as a result of further treatment [11, 12]"

Jan 1, 2012

By F. Leuzzi

Asbestos is a natural mineral fibre which has been known and utilized commercially for about a century. From the forties, it was employed on an ever-increasing scale throughout the mechanical engineering, building, paper-making and plastics sectors, to name but a few. There are essentially five minerals which provide fibres for industrial applications, namely, the chrysotile variety of serpentine and the amphiboles such as riebeckite, anthophyllite, cummingtonite-grunerite (amosite) and tremolite. About a fifth of the world's asbestos output was once taken by Europe for the manufacture of asbestos-cement products, reinforced plastics, paper and cardboard, panels, soft insulation and spray-on powders. However, in the sixties and seventies the hypothesis regarding the pathogenic nature of asbestos fibres started to gain ground. Moreover, between the sixties and eighties the EU issued a series of regulations designed to bring about a steady decrease in asbestos consumption. This line of action has culminated in recent years in a whole set of directives banning the use of asbestos in all products. This created a major problem, namely, how to clean-up the several million tons of various types of asbestos products in various states of conservation existing in Western Europe. CORDIAM (Pat. RM95 A 000269 and Pat. RM96 A 000782 in the name of ECOTEC S.r.1.) is one of the thermal inertization techniques recently proposed for this purpose. The process provides for the low-temperature ceramization of the toxic-harmful material. Of course, with such a great variety of waste materials and the volumes to be treated, as well as the need to ensure the correct dimensional design of the thermal sections of the treatment plant, it is necessary to know as much as possible about the thermal behaviour of the wastes concerned. This paper details the steps taken firstly to ascertain the thermal behaviour of such materials as may be encountered in day-to-day practice and secondly to examine the influence of the main process parameters on the preliminary design of gas- or fuel-oil-fired rotary kilns of the kind used for waste treatment.

Jan 1, 1999

The Port Kembla Copper (PKC) copper smelting facilities were commissioned during 2000. Numerous difficulties were encountered during the commissioning such as multiple reactor tuyere line failures, absorbing acid tower refractory collapse, and Noranda Reactor and Mitsubishi Converter process control problems. These problems are described along with the actions taken to overcome them. Process development is described particularly for the Mitsubishi Converter and Acid Plant.

Jan 1, 2002

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By Ki Bui Ma

Momentum wheels with superconducting bearings can integrate both attitude control and energy storage functions, with attendant savings in the total volume and weight of hardware, and power consumption, all of which are in short supply on mini-satellites. We have built and tested a prototype with a wheel of mass 1.9 kg, diameter 3.25 in, and height 3 in, which can store 3.5 J-sec of angular momentum and 5 kJ of energy when it rotates at an angular speed of 15000 RPM. The energy density of 2.5 kJ/kg achieved is comparable with the lower range for lead-acid batteries. To show that the wheel is energy efficient, we have performed spin down tests and measured the input power required to sustain rotational speed. Results indicate that power consumption, even accounting for the needs of cooling system, is significantly smaller than that for state of the art commercial reaction wheels.

Jan 1, 2002

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By Y. Maeda

Non-ferrous smelting furnaces generally install a gas cooling system for treatment of waste gas containing SO2,. From the point of view of corrosion resistance and recovery of waste heat, the high pressure boiler system is the best way to cool gas, however this system requires high initial investment and relatively higher operating costs. Because the feasibility of this boiler system greatly depends on the smelting process and scale, other lower temperature systems, e.g. water-cooled jacket system, are more suitable if the smelting process does not produce enough steam nor generate enough electricity to compensate operating cost. In additton, the water-cooled jacket system is simple in structure and easy to operate. For those reasons, it is applied widely. A new smelting furnace was planned in our factory and it was necessary to install waste gas cooling equipment. In our case, a water-cooled jacket system was more feasible because of the low gas volume and high dust content. It was also expected to operate without maintenance for ten years. On the other hand, some leakage problems with the water-cooled jacket had been experienced in the past. That is because SO2 In the waste gas changed into sulfuric acid which corroded the jacket material. As the first step, several data from actual' usage were reviewed to throw light on the corrosion process, and an appropriate procedure to determine the operating temperature of cooling water was obtained. For the basis of this study, a water-cooled jacket system was newly designed and tested for three months in a pilot plant. After this system's performance was confirmed, it was installed in a new furnace as a commercial plant. After one year of operation, the initial thickness of carbon steel jacket remains almost the same.

Jan 1, 1992

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By B. Balamurugan, D. J. Sellmyer, J. E. Shield, G. C. Hadjipanayis, Damien Le Ror, R. Skomski

"Rare-earth transition-metal (R-TM) alloys show superior permanent magnetic properties in the bulk, but the synthesis and application ofR-TM nanoparticles remains a challenge due to the requirement of high-temperature annealing above about 800 °C for alloy formation and subsequent crystalline ordering. Here we report a single-step method to produce highly ordered R-TM nanoparticles such as YCO5 and SmCO5, without high-temperature thermal annealing by employing a cluster-deposition system, and we investigate their structural and magnetic properties. Nanoparticles of size = 10 nm are monodispersed (s /d ~ 0.15) and have Hc values at T = 300 K of 8.0 and 4.5 kOe for YC05 and SmC05, respectively. Alignment of the easy axes is performed via a field applied to the clusters before deposition. These processing steps are highly desirable to create and assemble R-TM nanoparticle composites for future permanentmagnet applications.IntroductionMagnetic nanoparticles with high magnetocrystalline anisotropies (Ki > 1 MJ/m3) are required for permanent-magnet, recording-media, and other significant applications [1-3]. In this regard, bulk rare-earth transition metal alloys (R-TM) especially RC05 (R = Y and Sm) crystallized in the hexagonal CaCu5-type structure have shown a large Ki = 5 MJ/m3 (YC05) and 22 MJ/m3 (SmCo5) along with an appreciable saturation-magnetic polarization (Js, > 10 kG) and high curie temperatures (Tc > 1000 K) [2]. The challenges in controlling the size, sizedistribution, phase purity and crystalline ordering, however, limit the research on RCo5 nanoparticles [4,5]. The conventional arc-melting technique requires high-temperature annealing for alloy formation and subsequent crystalline ordering, which causes excess growth and thus results in nanocrystalline powders of particles sizes larger than 30 nm [6, 7]. Low-temperature wet-chemical techniques yield SmC05 nanoparticles of sizes smaller than 20 nm [5], but the control of phase purity is challenging due to the presence of surfactants and formation of other secondary phases [8]."

Jan 1, 2012

By G. Sterzik, W. A. Jankola, T. L. Salway, D. J. McKay

At Trail, British Columbia, Cominco's zinc leaching and solution purification processes include direct pressure leaching of zinc concentrates, leaching of fume from the lead smelter, leaching of calcine and electrolyte purification. These processes have been adapted to match the unique characteristics of Cominco's integrated zinc and lead operations. Recent modifications include changes to the purification process and iron-residue handling circuits. In 1997, a new five-compartment autoclave, complete with ancillary equipment, was installed in the pressure leaching plant. This paper discusses these changes, the current flowsheet and further improvements.

Jan 1, 2000

By C. M. F. Viera

In this work the properties of a clayey ceramic incorporated, up to 10 wt.%, with three types of wastes from a water treatment plant was evaluated. To determine the physical and mechanical properties such as linear shrinkage, water absorption and diametrical compression, specimens were prepared by 18 MPa uniaxial pressure and then fired in laboratory furnace at 700oC. The results indicated that the wastes incorporation changed the properties of the clayey ceramic. From the results it was found it possible to recycle these wastes into clayey ceramic in low amounts to avoid deleterious effect on the quality of the fired product.

Jan 1, 2008

By Beate Ina Jenssen

Ferric iron removal from the nickel electrolyte at Glencore Nikkelverk AS in Kristiansand, Norway, is achieved by precipitation of iron hydroxide followed by filtration, and it is desirable to improve filtration properties of the precipitated iron hydroxide in order to decrease the filtration time. The effect of increasing the residence time from the current 45 min to 75 min and temperature from 65 °C to 90 °C on the filtration properties of the precipitated iron hydroxide (akaganéite) was studied by simulating the industrial process conditions in a continuous reactor setup operating at steady state, using ferrous-containing process solution as feed material. It was possible to decrease the filter cake resistance by both increasing residence time and temperature, but temperature gave the most pronounced effect and reduced the filter cake resistance by one order of magnitude.

By R. W. Smith

A microorganism will function as a mineral flocculant if it is to some degree hydrophobic and can attach itself in some manner, such as through electrostatic interaction, to the fine mineral particles to be flocculated. The present paper concerns the use of a hydrophobic bacterium, Mycobacterium phlei, as flocculating agent for phosphate slimes. Experimental work on the flocculation of phosphate slimes and of dolomite and clay mineral suspensions was performed. It was found that M. phlei functions as an excellent flocculant for a dolomitic slime but does not function as well for mineral suspensions where large quantities of the solids are finer in size than the approximately 1 µm size of the bacterium.

Jan 1, 1992