Search Documents

By H. Cetin

The availability of coal resources of selected 7.5-minute quadrangles of southwest Indiana was examined in this study. Resources were defined as original coal in place, remaining after mining, and currently available considering land-use and technological restrictions. The amount of coal mined from each study area varies depending on the mining practices of the companies operating within the area. Of the three quadrangle investigations, the available resources range from 50 percent to 79 percent of the original resources. Most of the coal resources under deep-minable category were not available because of technologic restrictions, such as insufficient coal thickness.

Jan 1, 1996

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young's moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985

Integrated mining information and process control systems can reduce information delays, enhance decision making and improve the responsiveness of mining operations to, for example, variations in market conditions, mineral grades and ground conditions. This paper examines developments in the areas of: monitoring, data analysis and diagnosis,' communications systems; integrated mining support system;, and process and machine control. It concludes that the development of a comprehensive information technology plan is fundamental to the phased implementation of these technologies. In addition, hardware and software standards and concurrent digital design and simulation practices in selected manufacturing industries are examined and concluded to have relevance to the mining industry. Integrated information and process control systems will lead to emergence of the "digital mine". Such advances in mining information infrastructure as well as mining equipment will enable mining operations to shift from mass production methods to leaner production techniques. "Lean mining" aims to enhance and accelerate cash flow over the life of a mine by focusing on reduction of' throughput times; stockpiles for volume and quality control; and wastage and rework.

Jan 1, 1995

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

By Terence G. McCusker, E. Roy Anderson

A four-mile length of interceptor sewer tunnel in Manhattan has finished sizes ranging from 10'6" to 14'6" horseshoe. Mixed face conditions were anticipated in three areas and encountered in five. All were short but since the tunnel lies well below the water table and failures would involve important utilities, major structures and human lives, great care had to be exercized in choosing a construc¬tion method. Chemical consolidation was selected as the best approach with compressed air working as a backup system. Initially grouting was accomplished from within the tunnel, but treatment from the surface was more successful and was later adopted. The soils consisted largely of impermeable weak silts and it was found possible to inhibit access of water to this material so that it could be controlled by breasting within the tunnel without loss of stability. It is concluded that in the interlayered permeable and impermeable soils encountered, chemical grouting would successfully stabilize the working face. INTRODUCTION An interceptor sewer is currently under construction along the entire length of the west side of Manhattan. When complete, the tunnel will intercept and divert to a treatment plant (also under construction) a daily flow in excess of 200 million gallons per day. About 9 miles of the interceptor sewer is in tunnel and the remain¬der is cut-and-cover construction. The tunnel is almost entirely in Manhattan schist but where its alignment crosses major faults at comparatively shallow depths, mixed face and earth conditions are

Jan 1, 1997

By Alix Thierart, Yann Rouillard, Bernard Catalano

Bessac's presence in Singapore started in 2014 with the construction of the Thomson metro line, which includes 18 miles of twin-bore tunnels and 22 stations split into 17 construction packages. Bessac joint venture was allotted the T219 lot. The works include the construction of a new 660-foot (200-meter) long transfer station, two parallel 19-foot (5.8 m) ID tunnels and a pedestrian underpass. The urban context and the very soft ground stratum imposed to utilize unusual tunneling techniques, from upgrading a slurry TBM to a high-density slurry TBM to launch with very low cover and canopy pipe roofing completed with a MTBM without retrieval shaft.

Jun 23, 2024

Exploration for SX-EW copper deposits and plant operation depend largely on the copper and gangue mineralogy inasmuch as? they govern the feasibility of leaching. Mineralogical parameters are pivotal in identifying if an ore is suitable to dump, heap, thin layer, vat or agitated leaching and/or if the ore requires curing, bioleaching or alternate lixiviants. Problems in metallurgical testing, production leaching and recovery forecasting are very often related to lack of mineralogical data. This presentation will illustrate the use of quantitative mineralogical analysis for exploration, acquisition assessment and optimization of copper leach operations.

Jan 1, 1996

By Christopher Mark

Horizontal stresses are caused by global plate tectonic forces. During 1995 alone, they were largely responsible for closing two U.S. longwall mines. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky, and Alabama. In each case history, a mine encountered roof falls or difficult ground conditions in the headgate, caused by horizontal stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble-free. The paper also discusses detailed measurements made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel with the maximum horizontal stress, as previously thought, but rather 20° in the stress shadow of the gob. Other stress control techniques, including artificial support, are briefly discussed.

Jan 1, 1997

By B. Strickland

The decision to accelerate development of Stillwater Mining's East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and Rail Systems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km (3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By D. R. Nagaraj

Depression of copper sulfides followed by MoS2 flotation is the most commonly practiced technique for Cu-MO separation. Although numerous organic depressants have been developed in the past, a majority of the currently used copper depressants are inorganic compounds (ex. NaHS, Nokes reagent, etc.). A unique advantage of organic depressants over the inorganic compounds is the potential versatility for design of the organic molecule to suit many requirements. The present study was initiated to systematically investigate the structure- activity relationships for a large number of organic complexing agents in comparison with the commonly used inorganic depressants that are often inefficient and hazardous. The results obtained in this study are discussed in light of the useful correlation obtained between practical solution redox potential and depressant activity. Several requirements, such as the presence of an active -SH and hydrophilic -OH or -COOH in the organic molecule, are identified for a reagent to be a satisfactory depressant. Some preliminary results on the desorbability (or destruction) of collector coating on the sulfide surfaces in the non-xanthate collector systems are also discussed.

Jan 1, 1983

By W. J. Roberds

A formal and explicit yet cost-effective approach is proposed to ensure that decisions made during mine development are optimum (with respect to their ultimate consequences) as well as defensible. This risk management approach is based on probabilistic risk assessment and established decision analysis techniques, and appropriately considers the relationships among various mine development decisions, tradeoffs among consequences, the uncertainty in predicting consequences, and the benefits of flexibility to respond to changed conditions.

Jan 1, 1992

By Mustafa Fener, Masoud Rostami, Sair Kahraman, Behnaz Dibavar

The paper introduces a new rock mass cuttability classification (RMCC) system for roadheaders used in coal mines. It includes performance prediction models for both axial and transverse roadheaders, based on six parameters: uniaxial compressive strength, Cerchar abrasivity index, volumetric joint count, strike and dip of joints, joint aperture, and groundwater condition. The study validates the RMCC system through field and laboratory measurements, showing high correlation coefficients between net cutting rates and RMCC indices.

Nov 1, 2023

By W. P. Diamond

The Bureau of Mines has been investigating several techniques, including the use of horizontal and vertical boreholes, to remove gas from coal in advance of mining. Horizontal boreholes drilled from underground workings as part of the mining cycle have been shown (Finfinger, 1980; Hagwood, 1983; Perry, 1978; Prosser, 1981; Thakur, 1980; VonSchonfeldt, 1982) to be very effective in providing short-term, immediate relief from high methane emissions. This technique has been widely accepted in the coal mining industry, but it does require close coordination to integrate the drilling and subsequent gas drainage and disposal into the projected mine development plan. Vertical boreholes can be placed several years in advance of mining to predrain gas from coalbeds over relatively large areas (Dunn, 1984; Elder, 1975; Lambert, 1980; Steidl, 1978; Stubbs, 1979). The vertical borehole technique has the additional advantage over horizontal boreholes of allowing work to be performed on the surface instead of in the more restrictive underground environment. However, except for the relatively large scale vertical borehole programs for both mine safety and commercial production in the Black Warrior Basin of Alabama (Dunn, 1984; Lambert, 1980; Stubbs, 1979), the technique has been underutilized. The primary reason for this seems to be a combination of the current economic climate in the coal industry, legal questions as to the ownership of coalbed gas, and potential roof damage from the stimulation treatments required to increase the characteristically low permeability of coalbeds to enhance gas production. The question of potential roof damage is the subject of this paper.

Jan 1, 1985

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.